Ultra Start CJ series - Manuals

Page 2 - COMPONENTS; - Three Button Remote transmitter’s (430 Series); Table Of Contents Page 2; Components; Programming Page 7-9; INSTALL MANUAL; Table of Contents

COMPONENTS - Three Button Remote transmitter’s (430 Series) -Control Module - Four Button Remote transmitter’s (440 Series) - Plug-in Led - Plug-in Valet Switch (Program Switch) - Multi-Tone Siren - 10 Pin Main Harness - Installation Guide - 2 pin Keyless Entry harness - Owners Manual Table Of Conte...

Page 3 - INSTALL MANUAL; For modules with 10 pin connector only.; See page 4 for 11 pin connector.

Blue Connect to hood and / or trunk pin Hood Input Green Connect to door pin. (-) when opened Door Input Purple Connect to door pin. (+) when opened Door Input Black Connect to chassis ground Ground Input Brown Connect to Siren wire. 2amp Maximum Siren Output Red Connect to constant power. 20amp inp...

Page 4 - Red; For modules with 11 pin connector only.

INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 4 Blue Connect to hood and / or trunk pin Hood Input Green Connect to door pin. (-) when opened Door Input Purple Connect to door pin. (+) when opened Door Input Blk/White Dome Light Supervision Output (-) Dome Light Black Connect to chassis ground Ground ...

Page 5 - Recommended Installation Procedures; *This wire is only available on models with the 11 pin connector.; Under Hood Connections-; Wiring Descriptions

REMOTE VEHICLE SECURITY INSTALL MANUAL PAGE 5 Recommended Installation Procedures White (+) Park lights Park light output. Orange* (-) When Armed Negative output when system is armed. Grey* (-) Trunk Release Negative output for trunk release. Yellow (+) Ignition Input Input from vehicles ignition wi...

Page 6 - Step 3- Test And Adjust The Shock Sensor; Installing the Program Button-; Blue; Your Basic Install Is Complete!

INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 6 Step 3- Test And Adjust The Shock Sensor (see page 3) Recommended Installation Procedures Basic Install Installing the LED- Choose a location that will be highly visible when the LED is installed. Most vehicles are equipped with knock out panels in the d...

Page 7 - Changing A Programmable Setting; Quick View Programming; To Enter Program Mode; ) Press and release the Program Button; NOTE; Programming

REMOTE VEHICLE SECURITY INSTALL MANUAL PAGE 7 Changing A Programmable Setting Quick View Programming To Enter Program Mode 1) Make sure ignition is in the off position.2) Within three seconds turn the key ON the OFF. 3) Press and release the Program Button two times. 4) The siren will chirp and the ...

Page 8 - Enter Program Mode; Repeat sequence to change selection

INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 8 Enter Program Mode Entering program mode is done by the following steps: 1) Make sure ignition is in the off position.2) Turn the ignition key ON - OFF, leaving key in the OFF position. 3) Press and release the Valet button two times.4) The siren will ch...

Page 9 - Voltage / Door Pin Sensing; Chirps Door Pin- Door Pin Connection Required; Passive / Active Locks; Chirps Passive Locks; Passive / Active Arming; Chirps System Reset

REMOTE VEHICLE SECURITY INSTALL MANUAL PAGE 9 Voltage / Door Pin Sensing 1 - Enter Program Mode - (Ignition ON-OFF, followed by Valet 2 times) 2 - Press & release transmitter buttons in the following sequence #1 - #1 then #33 - The siren will respond with the following: 1 Chirp Voltage Sensing- ...

Page 10 - Transmitter Programming; - Turn the Ignition key; Exit; Car Jack Mode Activation

INSTALL MANUAL REMOTE VEHICLE SECURITY PAGE 10 Transmitter Programming Follow the steps below to program the transmitters to the system s memory Step 1 - Turn the Ignition key ON then OFF - Leaving Key Off. Step 2 - Press and release the Program Button twice then press and hold. Step 3 - The siren w...

Page 11 - Arm; disable will activate.; Disarm; Panic; Alar m Functions

REMOTE VEHICLE SECURITY INSTALL MANUAL PAGE 11 Arm 1. Press and release the button. 2. The park lights will flash and the siren will chirp one time. 3. The doors will lock (optional). NOTE : The LED will start flashing within five seconds. If installed, the starter disable will activate. Disarm 1.Pr...

Page 12 - Negative Park Lights-; White; Relay Wiring Diagrams

87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 Negative Type Door Locks Positive Type Door Locks 5 Wire / Reverse Polarity Type Door Locks Negative Park Lights- In some cases the park lights may flash erratically after installing the negative park light relay. To cor...