Ultra Start 43xx - Manuals

Ultra Start 43xx – Manual in PDF format online.

Manuals:

Manual

Manual Ultra Start 43xx

Summary

Page 2 - Door Lock Diagrams; Table of Contents; INSTALLATION MANUAL; WAY REMOTE STARTER/ALARM

Table of Contents Page 2 Pre-Installation Page 3 ComponentsFeature ListPre-Installation Installation Procedures Page 4 Wiring Diagrams Page 5-7 Wire Description Page 8-9 6 Pin ConnectorAuxiliary ConnectorsOptional ConnectorsJumper Positions Quick Start Installation Page 10 Basic InstallationPlug-in ...

Page 3 - REMOTE STARTER/ ALARM

Recommended Pre-Installation Procedures Feature List - Control module - 2way LCD and 1way transmitters - Antenna with built in - 6 pin main harness with dual - Program Button and LED’s 30 amp power inputs. - Multi-tone Siren - 11 pin harness** - 14 pin harness* - 4 pin harness** - 3 pin keyless entr...

Page 4 - Recommended Installation Procedures; Under Hood Connections -; BE CAREFUL; Mounting The Control Module -; Never; Installing the Exter nal Long Range Antenna -; BLUE; Security

Recommended Installation Procedures Under Hood Connections - Route the hood pin and tach wire through the firewall into the engine compartment. If possible route the wires through a factory rubbergrommet. If drilling a hole through the firewall, BE CAREFUL . Always check for obstructions on both sid...

Page 5 - Wiring Diagram - 11 pin + 4 pin Connectors; GREEN; RED

Wiring Diagram - 11 pin + 4 pin Connectors BLUE GREEN RED RED YELLOW Starter Output Heater/Acc Output Power Input Ignition Output Selectable Output Power Input 30amp Output 30amp Output 30amp Input 30amp Input 30amp Output 30amp Output * These connections are for manual transmission vehicles only! “...

Page 6 - Wiring Diagram 14 pin connector; YELLOW

Wiring Diagram 14 pin connector BLUE GREEN RED RED YELLOW 1 5 3 2 4 6 Starter Output Heater/Acc Output Power Input Ignition Output Selectable Output Power Input 30amp Output 30amp Output 30amp Input 30amp Input 30amp Output 30amp Output Factory Re-arm Output Starter kill & Anti-Grind Output Fact...

Page 7 - Wiring Diagram auxiliar y connectors; Door lock output; The jumpers control the output from the; WHITE; . Place the jumpers in the following order to change the output.; nd Starter; If the jumper is in position #2 the output on the white wire will be; nd Accessory; If the jumper is in position #3 the output on the white wire will be; nd Ignition; Output on White wire; Second Starter; Second Accessory; Second Ignition; Status Led’s; **The antenna MUST be connected for the system to operate; Green; Jumpers

Wiring Diagram auxiliar y connectors Door lock output Door unlock output (-) When Running Low Current (-) OutputLow Current (+) Output Door lock module output only* ACTIVE RF ANTENNA** (-) 500ma Output (-) 250ma Output (-) 250ma Output (-) 500ma Output (+) 500ma Output 1 2 3 The jumpers control the ...

Page 8 - Pin Power Connector; Auxiliary Connectors - 4, 11 and 14 pin Connectors; Negative input from hood pin safety switch.

6 Pin Power Connector 6-pin Description Test For Wire 1-Yellow 30amp Starter Output - This wire will test 0volts in off, accessory and in the ignition position.12volts during start only. 2-Green 30amp Heat/Acc Output - This wire will test 0volts in the off position 12- 14volts in the accessory and r...

Page 9 - Auxiliar y Connectors; continued from previous page; Ground; Pin Connector Red; Note; Pin Connector White

Auxiliar y Connectors - continued from previous page 11-Black Ground - System Chassis Ground Input. 12-Blue Glow Plug - Diesel Glow plug input, detects both 12volt and negative glow plug signals. Programmable input. See Menu 3. 13-Blue/White Tach - A/C Tach Signal Input. Used to detect when the vehi...

Page 10 - OFF

Step 1 - Connect All Of the Following Wires 6 Pin Power Connector Yellow 30amp Starter Output - 12volts during start position only. Green 30amp Heater Output - 12volts in the accessory position off during startand 12volts during run. Red 30amp Power Input - Constant 12volt power at ignition harness ...

Page 11 - Manual Transmission “M” Models; all; The starter wire travels form the key switch through the; Type 3 - Connect Switch; Install a relay to connect the two wires at the switch when the; Type 4 - Disconnect Switch; Install a relay to disconnect one of the wires at the clutch

Manual Transmission “M” Models Never install an automatic transmission remote starter into a manualtransmission vehicle!!! Doing so may result in serious injury or death. Do notinstall remote starters in convertible vehicles! The following wires must beconnected In addition to the basic remote start...

Page 12 - Auto Tach Learn; Your Basic Install Is Complete!; park lights are flashing a diagnostic code. See diagnostic chart.

Auto Tach Learn 1) Turn the ignition key to the “ON” position. (The park lights will turn on*).2) Start the vehicle with the key, The LEDs on the antenna will turn on if a proper tach signal is detected**, then after 30-35 seconds the park lights will flash and the sirenwill chirp twice to confirm T...

Page 13 - Impor tant Tach Notes; Quick lear n Tach; BRAKE; Press and hold the brake pedal.

Impor tant Tach Notes Tach Learning the remote starter is one of the most important steps in the installationprocess. Do not tach learn vehicle while the engine is in high idle. To ensure the bestpossible tach setting, ensure that the vehicle is at low idle/ normal operating RPM.Vehicles such as Toy...

Page 14 - Entering Program Mode; Press and release; Program Menus

Entering Program Mode 1) With the ignition in the OFF position, turn the ignition key from “Off” to “On” 3 times, ON-OFF-ON-OFF-ON within three seconds. (Leave the key in the ON position) 2) Press and release the Program Button located on the antenna. The park lights will flash and the siren will ch...

Page 15 - Quick View Progr amming; System Reset; System is now reset to factory defaults

Quick View Progr amming * See the following pages for more detailed programming instructions.Menu 1 - Press Lock 1 Flash 2 Flashes 3 Flashes 1 Ignition Lock Enabled Lock Only Disabled 2 Siren Chirp Type 1 Type 2 All Chirps 3 Lock&Unlock Options Double Unlock 3 second .75 second 4 Unlock/Disarm 1...

Page 16 - Menu 1- User Settings; WAY REMOTE STARTER/ ALARM

Menu 1- User Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Button #1 (Lock) Setting 1 Ignition Auto Lock 1) Ignition Lock & Unlock Enable 1 Flash/Chirp Doors Lock/Unlock with Ignition key. 2) Ignition Lock Only 2 Flashes/Chirps Doors Lock when ignition is turned ON ...

Page 17 - Menu 2 - Additional Settings

Menu 1- User Settings.. . continued from previous page Setting 6 Sensor Enable/Disable 1) Sensor Disabled 1 Flash/Chirp Impact Sensor Disabled *2) Sensor Enabled 2 Flashes/Chirps Impact Sensor Enabled Press & Release the Program Button 6 Times (Setting 6) Confirmed with 6 LED flashes. Press &...

Page 19 - Menu 3- Starter Settings

Menu 3- Starter Settings - Continued From Previous Page Setting 2 With 14pin Connector- Gas/Diesel Mode (Auxiliary Connector Pin 12) 1) (-) Input 1 Flash/chirp (-) Glow Plug input. Waits maximum 30 seconds then starts. 2) Time Delay 2 Flashes/chirps Waits for approximately 15 seconds then remote sta...

Page 20 - Menu 4- Tach Settings; Program Button; Setting 1- Auto Tach Learn; will chirp twice to confirm that a tach signal has been learned.

Menu 4- Tach Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Button #4 Setting 1- Auto Tach Learn 1) Perform a System Reset. See page 15. 2) Turn the ignition key on. (Park lights will turn on).3) Start the vehicle, the LEDs on the antenna will come on when a proper tach ...

Page 21 - Transmitter Programming; All the transmitters; WAY REMOTE STARTER/ALAM; Battery Replacement; Lift

Transmitter Programming Step 1 - Within 3 seconds turn the ignition ON-OFF-ON-OFF-ON - Leaving Key ON Step 2 - Press and hold the Program Button - The park lights will turn ON and the siren will chirp once.* Continue to hold the Program Button , the park lights will turn off and the siren will chirp...

Page 22 - Negative Type Door Locks 250ma; When installing relays always use a fused power source.

87 86 85 87a 30 87 86 85 87a 30 Lock Un lock VehicleLock/UnlockSwitch To Control Relay or Actuator Green Fused +12V Blue Ground Negative Type Door Locks 250ma Negative Door Locks (More Than 250ma) Positive Type Door Locks Note: When installing relays always use a fused power source. Blue Green Lock ...

Page 23 - DIAGNOSTICS; Wire / Reverse Polarity Type Door Locks

87 86 85 87a 30 87 86 85 87a 30 Blue Green Lock Un lock VehicleLock/UnlockSwitch To Actuator Fused +12V x x Cut Cut 87 86 85 87a 30 Ground DIAGNOSTICS 13 87 86 85 87a 30 87 86 85 87a 30 Blue Green Lock Un lock To Vacuum Pump Fused +12V x Cut Ground Page 23 2WAY REMOTE STARTER/ALARM INSTALLATION MANU...

Page 24 - DIAGNOSTIC MEMORY; Maximum four events, four chirps

DIAGNOSTICS If the remote starter does not activate when the start button is pressed the park lightswill flash a diagnostic to indicate what shutdown input has been triggered. For examplewhen the start button is pressed the park lights flash 3 times slowly. Looking at the chartbelow this would indic...