Ultra Start 25XX Series - Manuals

Ultra Start 25XX Series – Manual in PDF format online.

Manuals:

Manual

Manual Ultra Start 25XX Series

Summary

Page 2 - Table of Contents; INSTALLATION MANUAL; REMOTE VEHICLE STARTER/ALARM; Quick Learn

Table of Contents INSTALLATION MANUAL REMOTE VEHICLE STARTER/ALARM Page 2 Pre-Installation Page 3 ComponentsFeature ListPre-Installation Installation Procedures Page 4 Wiring Diagrams Page 5-7 Wire Description Page 8-9 6 Pin Connector14 Pin ConnectorAuxiliary OutputsOptional ConnectorsJumper Positio...

Page 4 - Recommended Installation Procedures; Under Hood Connections -; BE CAREFUL; Mounting The Control Module -; Never; Installing the External Long Range Antenna -; BLUE; Security

Recommended Installation Procedures Under Hood Connections - Route the hood pin and tach wire through the firewall into the engine compartment. If possible route the wires through a factory rubbergrommet. If drilling a hole through the firewall, BE CAREFUL . Always check for obstructions on both sid...

Page 5 - Wiring Diagra m

REMOTE VEHICLE STARTER/ALARM INSTALLATION MANUAL Page 5 Wiring Diagra m 1 3 5 2 4 6 2 1 4 3 6 5 7 8 10 10 10 9 12 12 11 11 14 13 13 4 PIN BLUE 30 AMP STARTER DISABLE RELAY- NORMALLY CONNECTED Blue Green Red Red Yellow White /Green White /Blue Red Starter Heater Main Power Ignition 1 Selectable Main ...

Page 6 - Side View; Blue; Pink; Jumper Selections - Back View; Jumper Access; 0amp relayed output; . To change the output of the wire access the jumpers by; nd Starter; If the jumper is in position #2 the output on the white wire will be; nd Accessory; If the jumper is in position #3 the output on the white wire will be; nd Ignition

Page 6 INSTALLATION MANUAL REMOTE VEHICLE STARTER/ALARM Side View PIN 4 RED P N 4 I W E HIT 4 PIN WHITE P N 3 I WHITE Note-250ma outputs are low current and are designed to activate relays Green PinkBlue Programmable * AUX #1 (Hold 1&3) * / (-) HORN OUTPUT* AUXILIARY OUTPUT #2 (Hold 2&3) Pro...

Page 7 - Description; Selectable output for 2nd Ign, acc or starter.; Function; Programmable output. See Menu 3; White; Continued on next page.; Pin Power Connector

Page 7 REMOTE VEHICLE STARTER/ALARM INSTALLATION MANUAL 6-pin Description Test For Wire 1-Yellow 30amp Starter Output This wire will test 0volts in off, accessory and in the ignition position.12volts during start only. 2-Green 30amp Heat/Acc Output This wire will test 0volts in the off position 12- ...

Page 8 - 4 Pin Connector; Continued From Previous Page; Pin Connector Red

Page 8 INSTALLATION MANUAL REMOTE VEHICLE STARTER/ALARM 14 Pin Connector Continued From Previous Page 1-Green Door Lock Door Lock Output - Programmable Menu 1 2-Red 12vlt Output Output For Door Lock Module Only! 3-Blue Door Unlock Door Unlock Output - Programmable Menu 1 4-Pink 2nd Unlock Output whe...

Page 9 - Step 1 - Connect All Of the Following Wires; 2volts during start position only.

Page 9 REMOTE VEHICLE STARTER/ALARM INSTALLATION MANUAL 6 Pin Power Connector Step 1 - Connect All Of the Following Wires Yellow 30amp Starter Output 12volts during start position only. Green 30amp Heater Output 12volts in the accessory position off duringstart and 12volts during run. Red 30amp Powe...

Page 10 - OFF

Step 1 - Connect All Of the Following Wires 6 Pin Power Connector Yellow 30amp Starter Output 12volts during start position only. Green 30amp Heater Output 12volts in the accessory position off during start and 12volts during the run position. Red 30amp Power Input Constant 12volt power at ignition ...

Page 11 - Manual Transmission “M” Models; all; The starter wire travels form the key switch through the; Type 3 - Connect Switch; Install a relay to connect the two wires at the switch when the; Type 4 - Disconnect Switch; Install a relay to disconnect one of the wires at the clutch

Manual Transmission “M” Models Never install an automatic transmission remote starter into a manualtransmission vehicle!!! Doing so may result in serious injury or death. Do notinstall remote starters in convertible vehicles! The following wires must beconnected In addition to the basic remote start...

Page 12 - Auto Tach Learn; Your Basic Install Is Complete!; park lights are flashing a diagnostic code. See diagnostic chart.

Auto Tach Learn 1) Turn the ignition key to the “ON” position. (The park lights will turn on*).2) Start the vehicle with the key, The LEDs on the antenna will turn on if a proper tach signal is detected**, then after 30-35 seconds the park lights will flash and the sirenwill chirp twice to confirm T...

Page 13 - Impor tant Tach Notes; Quick lear n Tach; BRAKE; Press and hold the brake pedal.

Impor tant Tach Notes Tach Learning the remote starter is one of the most important steps in the installationprocess. Do not tach learn vehicle while the engine is in high idle. To ensure the bestpossible tach setting, ensure that the vehicle is at low idle/ normal operating RPM.Vehicles such as Toy...

Page 14 - Entering Program Mode; Press and release; Program Menus

Entering Program Mode 1) With the ignition in the OFF position, turn the ignition key from “Off” to “On” 3 times, ON-OFF-ON-OFF-ON within three seconds. (Leave the key in the ON position) 2) Press and release the Program Button located on the antenna. The park lights will flash and the siren will ch...

Page 15 - Quick View Progr amming; System Reset; ON; System is now reset to factory defaults; does not

Quick View Progr amming * See the following pages for more detailed programming instructions.Menu 1 - Press Lock 1 Flash 2 Flashes 3 Flashes 1 Ignition Lock Enabled Lock Only Disabled 2 Siren Chirp Type 1 Type 2 All Chirps 3 Lock&Unlock Options Double Unlock 3 second .75 second 4 Unlock/Disarm 1...

Page 16 - Menu 1- User Settings

Menu 1- User Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Lock Button Setting 1 Ignition Auto Lock 1) Ignition Lock & Unlock Enable 1 Flash/Chirp Doors Lock/Unlock with Ignition key. 2) Ignition Lock Only 2 Flashes/Chirps Doors Lock when ignition is turned ON only....

Page 17 - continued from previous page; Setting 5 Active/Passive Locks; No auto-lock with passive arming; Flashes/Chirps Doors Lock when passive arming; to proceed to the next step.

Menu 1- User Settings .. . continued from previous page Setting 5 Active/Passive Locks 1) No Auto-Lock with Passive Arm 1 Flash/Chirp No auto-lock with passive arming *2) Doors Auto-Lock with Passive Arm 2 Flashes/Chirps Doors Lock when passive arming Press & Release the Program Button 5 Times (...

Page 18 - Menu 2 - Additional Settings

*(Default Settings) Menu 2 - Additional Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Unlock Button Setting 1 Secure Valet Mode - Length of time required to set the system into Service Mode 1) Secure Valet 1 Flash/chirp Hold the Program Button for 15 seconds *2) Normal ...

Page 19 - Menu 3- Starter Settings

Page 19 Menu 3- Starter Settings Ignition ON-OFF-ON-OFF-ON Press & Release Program Button Press Button #3 Setting 1 Special Door Lock/Unlock Operations (Factory Alarm Rearm) . 1) Type 1 1 Flash/chirp Unlock before start. Lock pulse after start and on shutdown. 2) Type 2 2 Flashes/chirps Lock pul...

Page 20 - Menu 4- Tach Settings; Setting 1 Auto Tach Learn.; will chirp twice to confirm that a tach signal has been learned.

Menu 4- Tach Settings Setting 1 Auto Tach Learn. 1) Perform a System Reset. See page 15. 2) Turn the ignition key on. (Park lights will turn on).3) Start the vehicle, the LEDs on the antenna will come on when a proper tach signal is detected*.4) After approximately 30-35 seconds the park lights will...

Page 21 - Transmitter Programming

Page 21 REMOTE VEHICLE STARTER/ALARM INSTALLATION MANUAL Step 1 - Within 3 seconds turn the ignition ON-OFF-ON-OFF-ON - Leaving Key ONStep 2 - Press and hold the Program Button - The park Lights will turn ON and the siren will chirp once. If the park lights do not come on atthis point, turn the igni...

Page 22 - Negative Type Door Locks 250ma; When installing relays always use a fused power source.

87 86 85 87a 30 87 86 85 87a 30 Lock Un lock VehicleLock/UnlockSwitch To Control Relay or Actuator Green Fused +12V Blue Ground Negative Type Door Locks 250ma Negative Door Locks (More Than 250ma) Positive Type Door Locks Note: When installing relays always use a fused power source. Blue Green Lock ...

Page 23 - DIAGNOSTICS; Wire / Reverse Polarity Type Door Locks

87 86 85 87a 30 87 86 85 87a 30 Blue Green Lock Un lock VehicleLock/UnlockSwitch To Actuator Fused +12V x x Cut Cut 87 86 85 87a 30 Ground DIAGNOSTICS 13 87 86 85 87a 30 87 86 85 87a 30 Blue Green Lock Un lock To Vacuum Pump Fused +12V x Cut Ground Page 23 REMOTE VEHICLE STARTER/ALARM INSTALLATION M...

Page 24 - DIAGNOSTIC MEMORY; Maximum four events, four chirps

DIAGNOSTICS If the remote starter does not activate when the start button is pressed the park lightswill flash a diagnostic to indicate what shutdown input has been triggered. For examplewhen the start button is pressed the park lights flash 3 times slowly. Looking at the chartbelow this would indic...