Tyan TYAN S1471 - Manuals - manualsarea.com

Page 2 - Table Of Contents

2 S1471-001-01 http://www.tyan.com Table Of Contents 1. Introduction....................................................................... 3 1.1 Overview................................................................31.2 Hardware Specifications.......................................... 41.3 Softwa...

Page 3 - Notice

3 S1471-001-01 http://www.tyan.com 1. Introduction 1.1 Overview The S1471 is a quality, high performance mainboard designed forl IntelPentium microprocessors. This mainboard utilizes the Intel 430VX chipsetand can support CPU speeds of 75MHz through 200MHz. S1470 willalso support the CyrixM1/6x86 CP...

Page 5 - Software Specifications; Trademarks

5 S1471-001-01 http://www.tyan.com w Mouse On-board PS/2 mouse connector. 1.3 Software Specifications w BIOS Award or AMI BIOS AT CMOS setup, BIOS/CHIPSET setup,and hard disk utility included.Support for easy BIOS upgrades with flashEPROM chip. w O.S. Operates with MS-DOS, Windows 3.x, Windowsfor Wo...

Page 6 - Board Installation; The mainboard package should contain the following:

6 S1471-001-01 http://www.tyan.com 2. Board Installation 2.1 Unpacking The mainboard package should contain the following: w S1471 Mainboard w One IDE 40 pin cables w Two serial cables w w One parallel cable w One 34 pin floppy cable w User's Manual The mainboard contains sensitive electric componen...

Page 7 - On Board Resource Setting; RTC; Socket 7; CPU; Voltage Regulator

7 S1471-001-01 http://www.tyan.com 3. On Board Resource Setting Figure 3.1 S1471 Board Layout KB CTR PWR CON. 5V ISA Slot 1 ISA Slot 2 ISA Slot 3 ISA Slot 4 KeyboardCON BIOS AMI/AWARD RTC PS/2MouseHeader J50 J13 J14 pin 1 Con 10 pin 1 PCI Slot 1 PCI Slot 2 PCI Slot 3 PCI Slot 4 PCI Slot 5 Secondary ...

Page 9 - Memory Voltage SIMMs:; Damage to system can result if these are set incorrectly!; Volts J5

9 S1471-001-01 http://www.tyan.com Memory Voltage SIMMs: Some EDO memory uses 3.3V. Damage to system can result if these are set incorrectly! Volts J5 J7 J9 J11 J3 J6 J8 Default 5V On On On On Off Off Off 3.3V Off Off Off Off On On On Memory Voltage DIMMs: Default is 5V. Volts JP1 JP2 JP3 Default 5V...

Page 15 - CPU Installation; The CPU is a sensitive electronic component and it can be easily; A cooling fan and heat sink assembly is required to protect the

15 S1471-001-01 http://www.tyan.com 1. Make sure the ZIF socket lever is up. To raise the lever, pull it out to the side a little and raise it as far as it will go. The top plate will slide back. 2. Align the CPU and socket Pin 1 corners. The pins on the bottom should align with the rows of holes in...

Page 16 - Upgrading Cache Memory; Peripheral Device Installation

16 S1471-001-01 http://www.tyan.com 3.11 Upgrading Cache Memory The S1471 has either 256Kb or 512kb of on-board pipelined burst SRAM. Since the SRAM is surfaced mounted onto the board,the L2 Cache cannot be field upgraded. 3.12 Peripheral Device Installation After all the jumpers on the mainboard ha...

Page 17 - Connecting the Power Supply; Good Power Signal; power

17 S1471-001-01 http://www.tyan.com 3.13 Connecting the Power Supply The system power supply connectors on the mainboard is for a 5 voltpower supply. Incorrect installation of the power supply could result inserious damage to the system board and connected peripherals. Good Power Signal VCC +12V -12...

Page 18 - Connecting 5V power supply

18 S1471-001-01 http://www.tyan.com Align the plastic guide pins on the lead cables to their receptacles on themainboard. You may need to hold the lead at an angle to line it up.Onceyou have the guide pins aligned, press the lead connector so that theplastic clips on the lead snap into place and sec...

Page 19 - BIOS Configuration

19 S1471-001-01 http://www.tyan.com 4. BIOS Configuration Award's BIOS has a built in setup program that allows the user to modifythe basic system configuration. This type of information is stored in thebattery-backed CMOS SRAM. Entering incorrect information or forget-ting your password can lock yo...

Page 21 - CMOS SETUP UTILITY

21 S1471-001-01 http://www.tyan.com 4.3. Getting Help 4.3.1. Main Menu The on-line description of the highlighted setup function is displayed at thebottom of the screen. 4.3.2. Setup Page menu/Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keysto use and...

Page 22 - Power Management setup; Automatically configure hard disk parameters.

22 S1471-001-01 http://www.tyan.com w w Standard CMOS setup This setup page includes all the items in a standard compatible BIOS. w w BIOS features setup This setup page includes all of the enhanced features of Award's BIOS. w w Chipset features setup This setup page includes all the items of the 43...

Page 23 - STANDARD CMOS SETUP

23 S1471-001-01 http://www.tyan.com w w Date The date format is <month>, <day>, <year>. Press <F3> to show the calendar. Base Memory: 640 K Extended Memory: 7168 KExpanded Memory: 0 KOther Memory: 384 K Total Memory: 8192 K ESC: Quit : Select Item PU/PD/+/-: Modify F1: Help (...

Page 24 - Drive A type/Drive B type

24 S1471-001-01 http://www.tyan.com N o n e No floppy drive installed 360K, 5.25 in. 5-1/4 inch PC-type standard drive; 360 kilobyte capacity 1.2M,5.25 in. 5-1/4 inch AT-type high-density drive; 1.2 megabyte capacity 720K, 3.5 in. 3-1/2 inch double-sided drive; 720 kilobyte capacity 1.44M, 3.5 in. 3...

Page 25 - Video; Color Graphics Adapter, power up in 40 column mode.; Halt On; Base Memory

25 S1471-001-01 http://www.tyan.com w w Video This category detects the type of graphics adapter used for the primarydisplay system. It must match your video display card and monitor. Al-though secondary monitors are supported, you do not have to select thattype in setup. EGA/VGA Enhanced Graphics A...

Page 26 - ROM ISA BIOS

26 S1471-001-01 http://www.tyan.com Expanded Memory Expanded Memory (EMS) defines a 64Kb page frame inthe area between 640K and 1Mb containing four 16K pagesthat are windows into the EMS memory. Programs issuerequests to the EMS manager to switch the page to anypart of EMS memory. Extended memory ca...

Page 27 - Default value is Disabled

27 S1471-001-01 http://www.tyan.com w w Virus warning This category flashes on screen. During and after the system boot up, any attempt to write to the boot sector or the partition table of the hard disk drive will halt the system and the following error message will appear. In the meantime, you can...

Page 28 - Default value is On; Memory Parity Check; The default value is disabled; Gate A20 Option

28 S1471-001-01 http://www.tyan.com w w Boot Up Floppy Seek During POST, the BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks while 720K, 1.2M and 1.44M are all 80 tracks. Default value is Enabled Enabled BIOS searches for floppy disk drive to determi...

Page 29 - Chipset Features Setup; The Chipset Features Screen; Security Option

29 S1471-001-01 http://www.tyan.com ROM ISA BIOS CHIPSET SETUP UTILITY AWARD SOFTWARE, INC. Auto Configuration :Enabled DRAM Timing :70ns DRAM RAS# Precharge Time :3DRAM R/W Leadoff Timing :6 DRAM RAS to CAS Delay :3 DRAM Read Burst Timing :x2222/x3333DRAM Write Burst Timing : x 2 2 2 2 Fast MA to R...

Page 32 - PCI Slot Configuration

32 S1471-001-01 http://www.tyan.com 4.8 PCI Slot Configuration ROM ISA BIOS PCI SLOT CONFIGURATION AWARD SOFTWARE, INC. Resource Controlled by :Manual Reset Configuration :Disabled IRQ3 assigned to :legacy ISA IRQ4 assigned to :legacy ISA IRQ5 assigned to : P C I / P n P IRQ7 assigned to :legacy ISA...

Page 33 - Select the PCI IRQ Active scheme either LEVEL or EDGE.

33 S1471-001-01 http://www.tyan.com w w Resources Controlled By The Award Plug and Play BIOS can automatically configure all the boot and Plug and Play compatible devices. If you seelect Auto, all the interrupt request and DMA assignment fields disappear, as the BIOS automatically assigns them. w w ...

Page 34 - Integrated Peripherals

34 S1471-001-01 http://www.tyan.com 4.9 Integrated Peripherals Integrated Peripherals Award Software, Inc. IDE HDD Block Mode :Enabled IDE Primary Master PIO :Auto IDE Primary Slave PIO :Auto IDE Secondary Master PIO :Auto IDE Secondary Slave PIO :Auto On-Chip Primary PCI-IDE :Enable On-Chip Seconda...

Page 35 - Load SETUP defaults; If any problem has occurred, loading the SETUP DEFAULTS is

35 S1471-001-01 http://www.tyan.com STANDARD CMOS SETUP PASSWORD SETTING BIOS FEATURES SETUP IDE HDD AUTO DETECTION CHIPSET FEATURES SETUP DAVE & EXIT SETUP PCI SLOT configuration EXIT WITH OUT SAVING LOAD SETUP DEFAULTS 4.9. LOAD SETUP DEFAULTS ROM ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC...

Page 38 - Flash Writer Utility; Warning: Do not flash the BIOS unless instructed by your dealer.; AMIFLASH.COM -The Flash Memory Writer utility for; Note

38 S1471-001-01 http://www.tyan.com 5.0 Flash Writer Utility Warning: Do not flash the BIOS unless instructed by your dealer. You can upgrade the BIOS of your mainboard by using a "FlashMemory Writer"(FMW) utility. This utility can be downloaded fromTyan's BBS(Consult your system vendor for ...

Page 40 - Once you have satisfied the two requirements mentioned above,; Warning: If you do not successfully install a complete BIOS file

40 S1471-001-01 http://www.tyan.com Once you have satisfied the two requirements mentioned above, you can run FMW. You can copy the contents of the “Flash”directory to your hard drive, or you can run the utility from abackup of the support floppy disk. Make sure the new BIOS fileis in the same direc...

Page 41 - Parity check error

41 S1471-001-01 http://www.tyan.com 6.0 System Resource6.1. TIMER & DMA CHANNEL MAP TIMER MAP: TIMER Channel-0 system timer interruptTIMER Channel-1 DRAM REFRESH requestTIMER Channel-2 SPEAKER tone generator DMA CHANNELS: DMA Channel-0 AvailableDMA Channel-1 AvailableDMA Channel-2 FLOPPY DISK ad...