Troy-Bilt STORM Series- Manuals

Operation 1. Do not put hands or feet near rotating parts, in the auger/impeller housing or chute assembly. Contact with the rotating parts can amputate hands and feet. 2. The auger/impeller control lever is a safety device. Never bypass its operation. Doing so makes the machine unsafe and may cause...

3 Setting Up Your Snow Thrower 6. Remove the flat washer and hairpin clip from the end of the chute directional control, Figure 3-5. Insert the end of the chute directional control into the lower bracket and secure with the flat washer and hair-pin clip just removed. If necessary, the lower bracket ...

8 4 Operating Your Snow Thrower Now that you have setup your snow thrower, it’s important to become acquainted with its controls and features. NOTE: For detailed starting instructions and more information on all engine controls, refer to the Tecumseh Engines manual packed separately. Shift Lever The...

10 Gas & Oil Fill-Up Service the engine with gasoline and oil as instructed in the Tecumseh Engines manual packed separately with your snow thrower. Read instructions carefully.Starting The Engine:1. Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug w...

14 6 Maintaining Your Snow Thrower WARNING Before lubricating, repairing, or inspecting, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop. Avoid oil spillage on rubber friction wheel and aluminum drive plate. Engine Refer to the separate Tecumseh Engin...

1 6 Maintaining Your Snow Thrower Auger Belt Replacement To remove and replace your snow thrower’s auger belt, proceed as follows:1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws, Figure 6-4. NOTE: Drain the gasoline from the snow thrower, or place ...

16 Augers • The augers are secured to the spiral shaft with two shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear, Figure 6-2. • If the augers will not turn, check to see if the pins have sheared. One set of re...

1 Friction Wheel Removal If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjust-ment fails to correct the problem, the friction wheel may need to be replaced. Follow the instructions below. Examine the friction wheel for signs of wear or crac...

18 Preparing Engine NOTE: Refer to the engine manual for more detailed information on preparing the snow thrower engine for storage. Short-Term Storage It is important to prevent gum deposits from forming in essential fuel system parts of the engine such as the carburetor, fuel filter, fuel hose, or...

3 This section addresses minor service issues. For further details, contact an authorized service center. 8 Trouble- shooting Cause Problem Remedy Engine fails to start 1. Choke not in ON position.2. Spark plug wire disconnected.3. Fuel tank empty or stale fuel.4. Engine not primed. 5. Faulty spark ...

0 9 19 4 36 7 56 7 4 50 39 53 27 46 41 44 47 40 49 15 20 45 3 26 24 9 28 5 8 12 23 7 14 54 1 18 52 48 55 51 38 43 31 33 35 11 2 7 9 4 4 34 33 31 21 33 29 30 16 25 57 13 33 10 32 22 42 37 6 Style N

1 9 Illustrated Parts List To order replacement parts, call 1-800-648-6776 or visit www.troybilt.com 1. 731-2635 Snow Removal Tool Mount 2. 684-04057 Impeller Assembly, 12” Dia. 3. 710-0347 Hex Screw, 3/8-16, 1.75, Gr5 4. 710-0451 Bolt, Carriage, 5/16-18, .750 Gr1 5. 710-0604A Screw, 5/16-18, 0.625 ...

The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States and /or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased and used in Canada and /or its territories and possess...

Operation 1. Do not put hands or feet near rotating parts, in the auger/impeller housing or chute assembly. Contact with the rotating parts can amputate hands and feet. 2. The auger/impeller control lever is a safety device. Never bypass its operation. Doing so makes the machine unsafe and may cause...

3 Setting Up Your Snow Thrower 6. Remove the flat washer and hairpin clip from the end of the chute directional control, Figure 3-5. Insert the end of the chute directional control into the lower bracket and secure with the flat washer and hair-pin clip just removed. If necessary, the lower bracket ...

8 4 Operating Your Snow Thrower Now that you have setup your snow thrower, it’s important to become acquainted with its controls and features. NOTE: For detailed starting instructions and more information on all engine controls, refer to the Tecumseh Engines manual packed separately. Shift Lever The...

10 Gas & Oil Fill-Up Service the engine with gasoline and oil as instructed in the Tecumseh Engines manual packed separately with your snow thrower. Read instructions carefully.Starting The Engine:1. Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug w...

14 6 Maintaining Your Snow Thrower WARNING Before lubricating, repairing, or inspecting, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop. Avoid oil spillage on rubber friction wheel and aluminum drive plate. Engine Refer to the separate Tecumseh Engin...

1 6 Maintaining Your Snow Thrower Auger Belt Replacement To remove and replace your snow thrower’s auger belt, proceed as follows:1. Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws, Figure 6-4. NOTE: Drain the gasoline from the snow thrower, or place ...

16 Augers • The augers are secured to the spiral shaft with two shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins may shear, Figure 6-2. • If the augers will not turn, check to see if the pins have sheared. One set of re...

1 Friction Wheel Removal If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjust-ment fails to correct the problem, the friction wheel may need to be replaced. Follow the instructions below. Examine the friction wheel for signs of wear or crac...

18 Preparing Engine NOTE: Refer to the engine manual for more detailed information on preparing the snow thrower engine for storage. Short-Term Storage It is important to prevent gum deposits from forming in essential fuel system parts of the engine such as the carburetor, fuel filter, fuel hose, or...

3 This section addresses minor service issues. For further details, contact an authorized service center. 8 Trouble- shooting Cause Problem Remedy Engine fails to start 1. Choke not in ON position.2. Spark plug wire disconnected.3. Fuel tank empty or stale fuel.4. Engine not primed. 5. Faulty spark ...

0 9 19 4 36 7 56 7 4 50 39 53 27 46 41 44 47 40 49 15 20 45 3 26 24 9 28 5 8 12 23 7 14 54 1 18 52 48 55 51 38 43 31 33 35 11 2 7 9 4 4 34 33 31 21 33 29 30 16 25 57 13 33 10 32 22 42 37 6 Style N

1 9 Illustrated Parts List To order replacement parts, call 1-800-648-6776 or visit www.troybilt.com 1. 731-2635 Snow Removal Tool Mount 2. 684-04057 Impeller Assembly, 12” Dia. 3. 710-0347 Hex Screw, 3/8-16, 1.75, Gr5 4. 710-0451 Bolt, Carriage, 5/16-18, .750 Gr1 5. 710-0604A Screw, 5/16-18, 0.625 ...

The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States and /or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased and used in Canada and /or its territories and possess...