Troy-Bilt REAR-TINE TILLER 675B- Manuals

Safety Decals For your safety and the safety of others, various safety and operational decals are located on your unit (see Figure 1-2 be­low). Keep the decals clean and legible at all times. Contact your local service dealer or the factory for replacements if any decals are damaged or missing. Refe...

SECTION 2: ASSEMBLY A WARNING: To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you have read and understand the safety and operating Instructions In this Manual. Introduction Carefully follow these assembly steps to correctly prepare y...

Figure 2-4: Attach handlebars. 5. Move the handlebars up or down to align the threaded hole In the cross-brace with one of the four slots in the curved height adjustment bracket. Place the keyed washer (E, Figure 2-3) on the flange head height adjustment screw (F) with the raised keys (edges) of the...

A CAUTION: Incorrect cable adjustment could cause the wheels and tines to rotate unexpectedly. Follow adjustment procedures carefully. Failure to do so could result in personal injury or property damage. 4. Check for correct spring^^able tension as instructed in Section 5, Checking and Adjusting For...

SECTION 3: FEATURES AND CONTROLS A WARNING: Before operating your machine, carefully read and understand all safety, controls and operating instructions in this Manual, the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious pe...

3. To m 0 ve the ti I le r i n reverse. fi rst stop al I forward motion. Lift up the handlebars un­ til the tines clear the ground and pull the Reverse Clutch lever out. The wheels will rotate in a reverse direction as long as the lever is held in REVERSE. To stop the wheels and tines, release the l...

SECTION 3: OPERATION A WARNING: Before operating your machine, carefully read and understand all safety (Section 1), controls (Section 3) and operating instructions (Section 4) in this Manual, In the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructio...

7. Choke or prime the engine as instructed in the separate Engine Owner’s Manual. 8. Check behind you to avoid contacting any obstacies when pulling the starter rope. Place one hand on the fuel tank to stabilize the unit and use the recoil starter to start the engine as instructed in the En­ gine Ow...

stopping the Tiller and Engine 1. To stop the wheels and tines, release the Forward Clutch levers or the Reverse Clutch Control (whichever is engaged). 2. To stop the engine, move the Engine Throttle Lever to STOP. 3. If the engine is equipped with a fuel shut­ off valve, close the valve as instruct...

TILLING TIPS & TECHNIQUES Tilling Depths A This is a CRT (counter-rotating tine) tiller. As the wheels pull forward, the tines rotate back­ward. This creates an “uppercut” tine action which digs deeply, uprooting soil and weeds. Don’t overload the engine, but dig as deeply as possible on each pa...

TILLING TIPS & TECHNIQUES fCONT) A. Tilling On Slopes Read the following recommendations before tilling on slopes; If you must garden on a moderate slope, please follow two very important guidelines: 1. Till only on moderate slopes, never on steep ground where footing is difficult (review safe­ ...

SECTIONS: MAINTENANCE A WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructi...

A WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for ail moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. A. To ...

A WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for ail moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. Carbur...

A WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for ail moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. A WARN...

A WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for ail moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. front ...

A WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for ail moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. TROUBL...

SECTION 6: PARTS LIST HANDLEBAR ASSEMBLY and CONTROL LEVERS 24

MODEL 675B Mount Tines So The Cutting Edge At The Top Of Each Tine Faces The Operator DENOTES CUTTING EDGE OF TINE LEFT-HAND TINE RIGHT-HAND TINE (BOTTOM) IIVIPORTANT: LEFT and RIGHT sides of tiller are determined by standing in the operator position (BEHIND THE HOOD) and facing the di­ rection of f...

TROY-BILT TILLER LIFETIME LIMITED WARRANTY WHAT PRODUCT IS COVERED All Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions. This warranty begins on the date of purchase and is warranted by Troy-Bilt LLC for the life of the tiller, to the original purchaser only. WHAT IS COV...