Troy-Bilt CS4210- Manuals

6 Attaching The Debris Collection Bag • To attach the bag, place the opening of the bag completely over the discharge chute. • Position the bag so that the wing knobs which secure the discharge chute to the impeller housing are completely covered. • Pull on the drawstrap until the bag is tight aroun...

7 Figure 4 SECTION 4: OPERATING YOUR CHIPPER SHREDDER WARNING: The operation of any chippershredder can result in foreign objects beingthrown. Always wear the safety glassesprovided with this unit or eye shields beforechipping or shredding and while performingany adjustments or repairs. Gas And Oil ...

8 • Grasp the starter handle and pull the rope out slowly until resistance is felt. When it becomes slightly harder to pull the rope, slowly allow the rope to recoil. Then pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. NOTE: A “clanking” noise may be heard w...

9 • Use the tamper to assist in feeding branches into the chipper chute. • Apply intermittent pressure (force, in short pulses) while feeding larger (2- 3-inch diameter) branches into the chipper chute, to avoid bogging or stalling the engine. IMPORTANT: Never feed branches with a diameter greater t...

10 Discharge Chute: Lubricate the pivot points on the chute deflector with light oil once a season. Engine: Refer to the Briggs & Stratton Owner/Operator manual packed with your unit for lubrication instructions. Maintenance Engine Refer to the Maintenance section of the Briggs & Stratton Ow...

11 Figure 9 NOTE: Use a 3/16” hex key (Allen) wrench on the outside of the blade and a 1/2” box (or socket) wrench on the inside of the impeller. See Figure 9. Hold the Allen wrench stationary and rotate the box (or socket) wrench to loosen the nut. • Install a replacement blade (Part No. 742-0544) ...

12 Storing Your Chipper Shredder • Clean the equipment thoroughly. • Wipe equipment with an oiled rag to prevent rust. • Refer to engine manual for correct engine storage instructions • Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer. SECTION 6: TROUBLESH...

MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. “Troy-Bilt” warrants this product against defects in material and workmanship for a period of ...

7 Figure 4 SECTION 4: OPERATING YOUR CHIPPER SHREDDER WARNING: The operation of any chippershredder can result in foreign objects beingthrown. Always wear the safety glassesprovided with this unit or eye shields beforechipping or shredding and while performingany adjustments or repairs. Gas And Oil ...

8 • Grasp the starter handle and pull the rope out slowly until resistance is felt. When it becomes slightly harder to pull the rope, slowly allow the rope to recoil. Then pull rope with a rapid, continuous, full arm stroke. Keep a firm grip on starter handle. NOTE: A “clanking” noise may be heard w...

9 • Apply intermittent pressure (force, in short pulses) while feeding larger (2- 3-inch diameter) branches into the chipper chute, to avoid bogging or stalling the engine. IMPORTANT: Never feed branches with a diameter greater than three (3) inches into the chipper chute. Doing so can result in ser...

10 Chute Deflector: Lubricate the pivot points on the chute deflector with light oil once a season. Engine: Refer to the Briggs & Stratton Owner/Operator manual packed with your unit for lubrication instructions. Maintenance Engine Refer to the Maintenance section of the Briggs & Stratton Ow...

11 Figure 9 NOTE: Use a 3/16” hex key (Allen) wrench on the outside of the blade and a 1/2” box (or socket) wrench on the inside of the impeller. See Figure 9. Hold the Allen wrench stationary and rotate the box (or socket) wrench to loosen the nut. • Install a replacement blade (Part No. 742-0544) ...

12 Storing Your Chipper Shredder • Clean the equipment thoroughly. • Wipe equipment with an oiled rag to prevent rust. • Refer to engine manual for correct engine storage instructions • Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer. SECTION 6: TROUBLESH...