Troy-Bilt 70- Manuals

Operation 1. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet. 2. Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of a...

6 Figure 3-1 IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine. NOTE: Reference to right and left hand side of the Chip-per/Shredder Vacuum is observed fr...

7 Figure 3- Figure 3-3 Figure 3-4 3 IMPORTANT Make sure the cables are routed outside the lower handle. Also, do not crimp the cables while lifting up the handles. Setting Up Your Chipper Shredder Vacuum Attaching The Handle 1. Remove the hairpin clips from the handle brackets and remove the carriag...

8 Figure 3-6 Attaching The Hose Assembly 5. a. Slide hose adapter of hose assembly into the base adapter located on the left front of the Yard Vacuum. See Figure 3-5. b. Pull spring loaded pin out on the base and align pin with the first hole (closest to the end of the tube) in the hose adapter. c. ...

9 Figure 3-8 A B C Figure 3-7 3 NOTE: The bag must be removed before installing the blower chute. Setting Up Your Chipper Shredder Vacuum Attaching The Bag 7. Grasp bag handle with one hand and slide locking rod on mounting bracket with other hand toward engine. Use the end of mounting bracket as le...

1 To Empty Bag 1. a. Unhook bag straps from the lower handle. b. Unsnap bag clip from the top of lower handle. See Figure 4-3. c. Grasp bag handle with one hand and pull lock rod on mounting bracket with other hand toward engine to release. d. Lift bag off back of unit.2. Twist the two buttons on th...

13 WARNING: Do not attempt to shred, chip, or vacuum any material larger than specified on the machine or in this manual. Personal injury or damage to the machine could result. IMPORTANT: The flail screen is located inside the housing in the discharge area. If the flail screen becomes clogged, remov...

14 WARNING: Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. General Recommendations Always observe safety rules when performing any maintenance.The warranty on this chipper/shredder vacuum does not co...

1 Maintaining Your Chipper Shredder Vacuum Figure 5-3 Figure 5-4 IMPORTANT: Make sure to insert the z-fitting into the rear hole as it was inserted in the front hole, that is from the outside of the drive control. 3. You may now carefully reinstall the drive control by performing the previous steps ...

16 Figure 5-5 Figure 5-6 Figure 5-7 Sharpening or Replacing Chipper Blade NOTE: When tipping the unit, empty the oil and fuel tank and keep engine spark plug side up. Disconnect and ground the spark plug wire to retaining post. Remove bag assembly or blower chute.Remove the three hex cap screws hold...

17 Carefully tilt and support the unit up to provide access underneath to the nozzle mounting hardware and impeller. Remove the three shoulder bolts securing the black plastic lower flail housing to the lower housing. Refer to Figure 5-8.Tilt top of black plastic lower flail housing toward the engin...

18 For repairs beyond the minor adjustments listed here, contact an authorized service dealer. 6 Trouble Shooting Cause Problem Remedy Engine fails to start 1. Throttle lever not in correct starting position. 2. Spark plug wire disconnected.3. Choke not in CHOKE position (if equipped). 4. Fuel tank ...

19 NOTES Use this page to make notes and write down important information.

1 7 Parts List Ref. Part No. Description 1. 736-0451 Saddle Washer, .320 x.93 2. 749-04163 Upper Handle 3. 720-0279 Knob 4. 710-1205 Eye Bolt 5. 781-1056 Upper Handle Bracket 6. 710-0726 Hex Cap Screw 5/16-12 x.750 7. 720-04072 Star Knob 8. 710-1174 Carriage Bolt 9. 731-04911 Nozzle Handle Clip 10. ...

MANUFACTURER’S LIMITED WARRANTY FOR GDOC-100020 REV. A The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States and/or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased ...

Operation 1. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet. 2. Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of a...

6 Figure 3-1 IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine. NOTE: Reference to right and left hand side of the Chip-per/Shredder Vacuum is observed fr...

7 Figure 3- Figure 3-3 Figure 3-4 3 IMPORTANT Make sure the cables are routed outside the lower handle. Also, do not crimp the cables while lifting up the handles. Setting Up Your Chipper Shredder Vacuum Attaching The Handle 1. Remove the hairpin clips from the handle brackets and remove the carriag...

8 Figure 3-6 Attaching The Hose Assembly 5. a. Slide hose adapter of hose assembly into the base adapter located on the left front of the Yard Vacuum. See Figure 3-5. b. Pull spring loaded pin out on the base and align pin with the first hole (closest to the end of the tube) in the hose adapter. c. ...

9 Figure 3-8 A B C Figure 3-7 3 NOTE: The bag must be removed before installing the blower chute. Setting Up Your Chipper Shredder Vacuum Attaching The Bag 7. Grasp bag handle with one hand and slide locking rod on mounting bracket with other hand toward engine. Use the end of mounting bracket as le...

1 To Empty Bag 1. a. Unhook bag straps from the lower handle. b. Unsnap bag clip from the top of lower handle. See Figure 4-3. c. Grasp bag handle with one hand and pull lock rod on mounting bracket with other hand toward engine to release. d. Lift bag off back of unit.2. Twist the two buttons on th...

13 WARNING: Do not attempt to shred, chip, or vacuum any material larger than specified on the machine or in this manual. Personal injury or damage to the machine could result. IMPORTANT: The flail screen is located inside the housing in the discharge area. If the flail screen becomes clogged, remov...

14 WARNING: Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. General Recommendations Always observe safety rules when performing any maintenance.The warranty on this chipper/shredder vacuum does not co...

1 Maintaining Your Chipper Shredder Vacuum Figure 5-3 Figure 5-4 IMPORTANT: Make sure to insert the z-fitting into the rear hole as it was inserted in the front hole, that is from the outside of the drive control. 3. You may now carefully reinstall the drive control by performing the previous steps ...

16 Figure 5-5 Figure 5-6 Figure 5-7 Sharpening or Replacing Chipper Blade NOTE: When tipping the unit, empty the oil and fuel tank and keep engine spark plug side up. Disconnect and ground the spark plug wire to retaining post. Remove bag assembly or blower chute.Remove the three hex cap screws hold...

17 Carefully tilt and support the unit up to provide access underneath to the nozzle mounting hardware and impeller. Remove the three shoulder bolts securing the black plastic lower flail housing to the lower housing. Refer to Figure 5-8.Tilt top of black plastic lower flail housing toward the engin...

18 For repairs beyond the minor adjustments listed here, contact an authorized service dealer. 6 Trouble Shooting Cause Problem Remedy Engine fails to start 1. Throttle lever not in correct starting position. 2. Spark plug wire disconnected.3. Choke not in CHOKE position (if equipped). 4. Fuel tank ...

19 NOTES Use this page to make notes and write down important information.

1 7 Parts List Ref. Part No. Description 1. 736-0451 Saddle Washer, .320 x.93 2. 749-04163 Upper Handle 3. 720-0279 Knob 4. 710-1205 Eye Bolt 5. 781-1056 Upper Handle Bracket 6. 710-0726 Hex Cap Screw 5/16-12 x.750 7. 720-04072 Star Knob 8. 710-1174 Carriage Bolt 9. 731-04911 Nozzle Handle Clip 10. ...

MANUFACTURER’S LIMITED WARRANTY FOR GDOC-100020 REV. A The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States and/or its territories and possessions, and by MTD Products Limited with respect to new merchandise purchased ...