Troy-Bilt 675B--Pony- Manuals

6 WARNING: To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you have read and understand the safety and operating instructions in this Manual. Introduction Carefully follow these assembly steps to correctly prepare your tiller for use. ...

8 CAUTION: Incorrect cable adjustment could cause the wheels and tines to rotate unexpectedly. Follow adjustment procedures carefully. Failure to do so could result in personal injury or property damage. 4. Check for correct spring ⁄ cable tension as instructed in Section 5, Checking and Adjusting F...

9 WARNING: Before operating your machine, carefully read and understand all safety, controls and operating instructions in this Manual, the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious personal injury. Tiller Features Th...

10 3. To move the tiller in reverse, first stop all forward motion. Lift up the handlebars until the tines clear the ground and pull the Reverse Clutch lever out. The wheels will rotate in a reverse direction as long as the lever is held in REVERSE. To stop the wheels and tines, release the lever an...

11 WARNING: Before operating your machine, carefully read and understand all safety (Section 1), controls (Section 3) and operating instructions (Section 4) in this Manual, in the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructions can result in ser...

12 7. Choke or prime the engine as instructed in the separate Engine Owner’s Manual. 8. Check behind you to avoid contacting any obstacles when pulling the starter rope. Place one hand on the fuel tank to stabilize the unit and use the recoil starter to start the engine as instructed in the En-gine ...

13 Stopping the Tiller and Engine 1. To stop the wheels and tines, release the Forward Clutch levers or the Reverse Clutch Control (whichever is engaged). 2. To stop the engine, move the Engine Throttle Lever to STOP. 3. If the engine is equipped with a fuel shut- off valve, close the valve as instr...

14 Preparing Seedbeds Tilling wet soil often results in large, hardclumps of soil that can interfere with plant-ing. If time permits, wait a day or two afterheavy rains to allow the soil to dry beforetilling. Test soil by squeezing it into a ball. Ifit compresses too easily, it is too wet to till. A...

15 Tilling On Slopes Read the following recommendations before tilling on slopes: If you must garden on a moderate slope, please follow two very important guidelines: 1. Till only on moderate slopes, never on steep ground where footing is difficult (review safe-ty rules in Section 1: Safety of this ...

16 WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructions can result in ser...

17 A. To Check Transmission 1. Check the gear oil level when the trans- mission is cool. Gear oil expands in warm operating temperatures and will result in an incorrect oil level reading. 2. To check the gear oil level (and to add oil, if necessary), refer to STEP 5: Check Gear Oil Level in Transmis...

18 Carburetor / Governor Adjustment WARNING: Operators shall not tamper with the engine governor settings; the governor controls the maximum safe operating speed to protect the engine and all moving parts from damage caused by overspeed. Authorized service shall be sought if a problem exists. The ca...

19 WARNING: This is a CRT (counter-rotating tine) tiller and its tines must be mounted in the direction shown in Figure 5-7. Failure to comply could result in personal injury or property damage. 2. When installing individual tines, install them in the reverse order from which they were removed. The ...

20 NOTE: While pushing inward on theforward idler arm, be sure that theforward drive belt is moved off to theright side of the tiller. This createsmore room to install the clevis pinwhen the forward idler arm is pushedinward. IMPORTANT: When the clevis pin is installed in the inner hole of the forwa...

21 front of the unit (not the operator’s posi-tion). If the belt tension is correct, reinstall the belt cover and secure it with the two nuts. • If the guide mark is aligned with the guide pin, or moves to the right side of the guide pin, then the belt is too loose and the tension must be readjusted...

23 WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. TROUB...

TROY-BILT TILLER LIFETIME LIMITED WARRANTY WHAT PRODUCT All Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions. IS COVERED This warranty begins on the date of purchase and is warranted by Troy-Bilt LLC for the life of thetiller, to the original purchaser only. WHAT IS COVE...