Troy-Bilt 12001C- Manuals

at the tiller for damage, and repair damage be­ fore restarting and operating the tiller. 5. Exercise caution to avoid slipping or falling. 6. If the machine should start to vibrate abnor­ mally, stop the engine. Disconnect the spark plug wire and prevent it from touching the spark plug, and check i...

DECALS If any of the decals below become illegible, damaged, or missing, order replacements immediately. See the Parts Ordering Information at the back of this Manual. Serial Number Engine Ignition Warning Photo 1: Decals

Section 2: Easy Assembly_______________ Please follow the steps in this Section to assemble your tiller and prepare it for use. These steps will not take long and will assure correct assembly of your new tiller. We recommend you read this Section ail the way through first. Then begin the assembly st...

ASSEMBLY STEPS You’ll need the following tools for assembly: • Two 7/16" wrenches ( a 7/16" socket, exten­ sion, and ratchet can be substituted for one of the 7/16" wrenches). • One Medium size Phillips head screwdriver. 1. Unwind the throttle cable from around the en­ gine. Use care whe...

Section 3: Operation Your equipment is now assembled and ready to be serviced with the correct fuei/oii mixture. THE GASOLINE / TWO‘CYCLE ENGINE OIL MIXTURE Since your tiiler has a Tecumseh two cycle (“two-stroke”) engine, you MUST mix together a quality two-cycle oil with gasoline. The mixture is 2...

Figure 10: Select the right fuel priming tech­ nique: High Volume (A) or Standard Volume (B). A WARNING Do not touch the Throttle Control Lever while starting the engine. The tines may propel the machine forward if the engine speed is advanced from idle. Failure to follow these instructions can re­ ...

6. If you need to make any adjustments to the tilling depth: a. Turn the engine OFF. Disconnect the spark plug wire. b. Remove the hairpin cotter and the clevis pin from the depth stake bracket. c. Move the depth stake down for deeper tilling and cultivating, or up for shallower work. d. Reinsert th...

Remounting the tine gangs takes just a coupie )f minutes and you’ll need a pliers at most. The ■igures to the right show the conventional tine :onfiguration where there is a narrow gap be- ween the center (inner) tines, and the special itony soil tine pattern where the inner tine gangs lave been swa...

To lubricate the transmission: 5. Place the nozzle of a grease gun on the rim of the middle hole. Push the nozzle firmly up against the opening.6. Apply grease until it begins to come out of the bottom hole. Replace the bottom plug securely. Then apply grease to the top plug hole. Add until it begin...

TINE REMOVAL & INSTALLATION A WARNING Worn tines may become sharp. Wear heavy gloves when removing, handling, or rein­ stalling tines to prevent personal injury. IMPORTANT The four tines are not interchangeable. They must be reinstalled in the same posi­ tions from which you removed them and the...

Düst; Cover "WÌtlT^ Jeft Washer Photo 18: Installing an inner tine. B. Slide the inner tine over the tine shaft. C. Slide the outer tine over the tine shaft. D. Secure the tines to the tine shaft by inserting the hairpin cotter in the outer hole in the tine shaft. It is easier to install the hai...

Ref. No. Description Part No. 1 ................ Transmission Case, with pressed-in bushing, leftside.......................... 1915039. 2 ................Transmission Case, with pressed-in bushing, right side...................... 1915040.3 ................Oil Seal.....................................

LIIVIITED WARRANTY Products Covered This warranty is for the following TROY-BiLT® branded products and their attachments or accessories: chipper/shredders, chipper/vacs, walk-behind mowers, riding mowers, tractors, snow throwers, brush- cutters, sprayers, carts, composters and the Mini-Tiller. Date ...