Trinity TR20190 - Manuals - manualsarea.com

Page 2 - Contents

Contents Introduction 2 Safety precautions 2 Installation 4 Installing the charcoal filer 8 Operation 9 Care and maintenance 10 Troubleshooting 11 Environmental protection 12

Page 3 - Introduction; Thank you for choosing this extractor hood.; Safety precautions; Never let the children operate the machine.

2 Introduction Thank you for choosing this extractor hood. To ensure that you get the best results from your new extractor, we strongly suggest that you read this instruction manual thoroughly before use. If treated with care, your extractorshould give you years of trouble-free use To register owner...

Page 4 - Do not flambé under the cooker hood.; Electrical shock hazard

3 damaged. A damagesupply cord must be replaced by qualified service personnel only. Please contact the service department. - If the room where the hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed orbalanced flue type. Ifother ...

Page 5 - Installation; Prepare for the installation:; below picture by means of an extraction duct

4 65cm - 76cm Installation Prepare for the installation: a. If you have an outlet to the outside, your cooker hood can be connected as per the below picture by means of an extraction duct with an interior diameter of 150mm. b. Before installation, turn the unit off and unplug it from the outlet. c. ...

Page 6 - Lift up the cooker hood and hang it onto the wall bracket hooks.

5 Holes on Screw Screw Wall Cooker hood Wall bracket Installation – ducted Attention! Observe the warning concerning the operation of the appliance when air is discharged from the room. Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten the bracket onto the wall with the screws and sc...

Page 7 - Chimney installation.; can be telescopically adjusted after assembled.

6 Exhaust pipe Cooker hood Fix the one-way-valve to the air outlet of the cooker hood. Then, attach the exhaust pipe to the one-way-valve as shown below. Chimney installation. Place the upper chimney into the lower chimney . Use 2 pcs ST4x8mm screws to attach lower and upper chimney together. Before...

Page 8 - Fix the lower chimney with the hood with 2 screws ST4x8mm

Drill 2 holes to accommodate the plate II. Screw and tighten the plate II onto the wall with two screws and wall.plugs provided Slide up the upper chimney and fix the upper chimney with plate II with 2 screws ST4x8mm Fix the lower chimney with the hood with 2 screws ST4x8mm

Page 10 - Operation; Low speed button

9 Operation Low speed button Is suitable for simmering and cooking which does not produce much odour. Medium speed button The airflow speed is ideal for extracting with regular cooking. High speed button When a high amount of smoke or odour is produced, press the high speed button for the most effec...

Page 11 - Care and maintenance

10 Care and maintenance IMPORTANT: Before cleaning or maintenance please switch off the electricity supply and remove the plug from the wall. Regular cleaning Use a soft cloth moistened with lukewarm mildly soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive materi...

Page 12 - Troubleshooting

11 Replacing the bulb 1. Switch the unit off and unplug the appliance. 2. Remove the lamp cover by unscrewing the 2 screws. 3.Unscrew the bulbs. 4.Replace with the same type and rated bulb/lamp. Troubleshooting Fault Cause Solution The lights on, but the fan does not work The fan blade is jammed. Sw...

Page 13 - Environmental protection

12 Environmental protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. This appliance is marked according to the European directive 2012/19/EC on Waste Electrical a...