TP-Link TL-SF1024D - Manuals

Page 2 - COPYRIGHT & TRADEMARKS; Specifications are subject to change without notice.; FCC STATEMENT; may cause undesired operation.; CE Mark Warning

COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form ...

Page 3 - CONTENTS; Chapter 1

CONTENTS Package Contents ................................................................................................ 1 Chapter 1 Product Introduction ....................................................................... 2 1.1 Product Overview ....................................................

Page 4 - Package Contents; The following contents should be found in your box:

1 Package Contents The following contents should be found in your box: ¾ One TL-SF1016/TL-SF1016DS/TL-SF1024/TL-SF1024D/TL-SF1048 Switch ¾ One power cord ¾ This User Guide ¾ Mounting screws and two “L” planks Note: Make sure that the package contains the above items. If any of the listed items are d...

Page 5 - Chapter 1 Product Introduction; Product Overview; LED indicators for monitoring power, link, activity, speed

2 Chapter 1 Product Introduction This chapter describes the features of the model of TL-SF1016/TL-SF1016DS/TL-SF1024/TL-SF1024D/TL-SF1048 16/24/48-port 10/100Mbps Fast Ethernet Switch. TL-SF1016, TL-SF1024 and TL-SF1048 just differ in the size, the number of LED indicators and ports, and all figures...

Page 6 - Chapter 2 Identifying External Components; Power LED

3 Chapter 2 Identifying External Components This Chapter describes the front panel, rear panel and LED indicators of the Switch. 2.1 Front Panel The front panel of TL-SF1016 consists of switch model, switch LED indicators, and 16 10/100Mbps RJ-45 ports. Figure 2-1 TL-SF1016 Switch Front Panel sketch...

Page 7 - TL-SF1016 already comes with Lightning Protection; Connect to Ground; Connect the female connector of the power cord here, and

4 ¾ Grounding Terminal: TL-SF1016 already comes with Lightning Protection Mechanism. You can also ground the Switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable. For detail information, please refer to section 3.3 Connect to Ground . ¾ AC Power Socket: Connect the female c...

Page 8 - Chapter 3 Installation; ) Safety Requirements

5 Chapter 3 Installation 3.1 Precautions To ensure a long-term and stable performance of the Switch, please pay attention to the following before the installation. 1) Safety Requirements • Before cleaning the Switch, cut off the power supply. Do not clean it by the waterish cloth, and never use any ...

Page 10 - Connect to Ground

7 1) Secure the supplied rack-mounting brackets to each side of the Switch with supplied screws, as illustrated in the following figure. Figure 3-2 Attaching Brackets 2) After the brackets are attached to the Switch, use suitable screws (not provided) to secure the brackets to the rack, as illustrat...

Page 11 - from electric shock.; Connecting to the Grounding Bar; Protecting Earth

8 from electric shock. In different environments, the Switch may be grounded differently. The following will instruct you to connect the Switch to the ground in two ways, connecting to the Grounding Bar or connecting to the Ground via the power cord. Please connect the Switch to ground in the optimu...

Page 13 - Appendix A: Specifications; General

10 Appendix A: Specifications General Standards IEEE802.3 10Base-T, IEEE802.3u 100Base-TX Topology Star Protocol CSMA/CD Ethernet: 10Mbps (Half Duplex) 20Mbps (FullDuplex) Data Transfer Rate Fast Ethernet: 100Mbps (Half Duplex) 200Mbps (Full Duplex) 10Base-T: UTP category 3, 4, 5 cable (maximum 100m...

Page 14 - Appendix B: Troubleshooting; The Power LED is not lit; Make sure the power source is ON.

11 Appendix B: Troubleshooting 1. The Power LED is not lit ¾ Make sure the AC power cord connected the Switch with power source properly. ¾ Make sure the power source is ON. 2. The Link/Act LED is not lit when a device is connected to the corresponding port ¾ Make sure that the cable connectors are ...