Toyota 5613- Manuals

Page 2 - Before Starting Installation; Engine Compartment; Inside Cab; Prepare to Install Kit; Measurements

2 ‘05 - ‘06 Tacoma (W/ O.E. Hitch) - 3” Kit 5613 Before Starting Installation 1. Carefully read all warnings and instructions com-pletely before beginning. 2. Verify all parts have been received in this kit bychecking the parts list at the end of this document. 3. Only install this kit on the vehicl...

Page 3 - Front of Vehicle

3 ‘05 - ‘06 Tacoma (W/ O.E. Hitch) - 3” Kit 5613 Front of Vehicle 1. Front bumper a. Remove wiring harnesses from fog lights, ifequipped. b. Remove two pop-up clips, two bolts and grillfrom core support. c. Remove seven pop-up clips from front bumper. WiringHarness Fog Light Bolts Pop-upClips Grill ...

Page 7 - Inside of Vehicle

7 ‘05 - ‘06 Tacoma (W/ O.E. Hitch) - 3” Kit 5613 14. Steering Shaft a. Strap steering wheel to prevent accidentalmovement. b. Mark upper steering shaft in relation to couplerand lower steering shaft. c. Remove coupler bolts, slide coupler up ontoupper steering shaft and disconnect steeringshaft. d. ...

Page 9 - Underside of Vehicle

9 ‘05 - ‘06 Tacoma (W/ O.E. Hitch) - 3” Kit 5613 e. Remove four bolts, and driver and passengerbody mount access plates. f. Remove driver and passenger body mount boltaccess covers. 4. Crew cab models: Rear interior trim panels a. Remove three headrests from seatbacks andfold seatbacks down. b. Remo...

Page 11 - Rear of Vehicle

11 ‘05 - ‘06 Tacoma (W/ O.E. Hitch) - 3” Kit 5613 Rear of Vehicle 1. Fuel filler a. Remove fuel filler cap. b. Loosen two hose clamps and disconnect venthose connector. c. Remove bolt and fuel filler from vehicle. WARNING Use extreme caution when working near the fuel linesand the fuel tank. Clean u...

Page 12 - Install Kit; Cab

12 ‘05 - ‘06 Tacoma (W/ O.E. Hitch) - 3” Kit 5613 Install Kit Cab 1. Lift cab a. Loosen, but DO NOT REMOVE, cab mountingbolts on driver side. b. Remove bolt, nut, and lower washer from eachcab mount on passenger side. NOTE The number of cab mounting bolts may vary with thelength of the cab. Cab Moun...

Page 14 - Bed

14 ‘05 - ‘06 Tacoma (W/ O.E. Hitch) - 3” Kit 5613 3. Cab driver side a. Repeat previous steps on driver side of cab. b. Set cab-to-bed spacing according to previousmeasurement. c. Remove front core support cab mount kit bolts (3/8” x 8”) and apply a few drops of kit Loctite ® to threads. Install kit...

Page 30 - After Completing Installation; Dynamic Vehicle Check

30 ‘05 - ‘06 Tacoma (W/ O.E. Hitch) - 3” Kit 5613 After Completing Installation Inside Cab 1. Install airbag fuse and fuse block cover. Engine Compartment 1. Connect both battery cables. Connect positive cablefirst, then negative cable. Fuse Cover Fuse LocationMay Vary Airbag Fuse NegativeCable (Bla...

Page 31 - Accessories; The following accessories are also available:

31 ‘05 - ‘06 Tacoma (W/ O.E. Hitch) - 3” Kit 5613 Accessories The following accessories are also available: Kit # 6337: Gap Guards

Page 32 - Kit Parts List; Description

32 ‘05 - ‘06 Tacoma (W/ O.E. Hitch) - 3” Kit 5613 Kit Parts List Qty. Description NOTE Depending on the vehicle configuration (automatic ormanual transmission, 2WD or 4WD, cab length, bedlength, etc.), some parts may not be used. 8 Block (2" x 3" spacer) 4 Block (3" x 3" spacer) 1 Br...