Toyota 2012 Tacoma- Manuals

29 Vehicle control and operation data recording Your Toyota is equipped with sophisticated computers that record certaininformation about your vehicle’s operation, such as: • Engine speed• Accelerator status• Brake status• Vehicle speed• Shift position (except manual transmission) The data recorded ...

31 CAUTION ■ General precautions while driving Driving under the influence: Never drive your vehicle when under the influ-ence of alcohol or drugs that have impaired your ability to operate your vehi-cle. Alcohol and certain drugs delay reaction time, impair judgment andreduce coordination, which co...

32 Symbols used throughout this manual Cautions & Notices Symbols used in illustrations CAUTION This is a warning against anything which may cause injury to people if thewarning is ignored. You are informed about what you must or must not do inorder to reduce the risk of injury to yourself and o...

TABLE OF CONTENTS 1 1 Before driving Adjusting and operating features such as door locks, mirrors, and steering column. 2 When driving Driving, stopping and safe-driving information. 3 Interior and exterior features Air conditioning and audio systems, as well as other in-terior features for a comfor...

34 1-1. Key information Keys ■ Key number plate Keep the plate in a safe place such as your wallet, not in the vehicle. In theevent that a key is lost, a new key can be made by your Toyota dealer usingthe key number plate. ( → P. 534) The following keys are provided with the vehicle. Vehicles withou...

35 1-1. Key information 1 Before driving NOTICE ■ To prevent key damage (vehicles with engine immobilizer system) ● Do not subject the keys to strong shocks, expose them to high tempera-tures by placing them in direct sunlight, or get them wet. ● Do not expose the keys to electromagnetic materials o...

36 1-2. Opening, closing and locking the doors Wireless remote control ∗ ∗ : If equipped ■ Operation signals A buzzer sounds and the emergency flashers flash to indicate that the doorshave been locked/unlocked. (Locked: Once; Unlocked: Twice) ■ Panic mode ■ Door lock buzzer If a door is not fully cl...

38 1-2. Opening, closing and locking the doors ■ Certification for wireless remote control MODEL/FCC IDs: Transmitter: GQ43VT20T Receiver: GQ4-34R IC (Canada) IDs: Transmitter: 1470A-1T Receiver: 1470A-6R MADE IN U.S.A. This device complies with Part 15 of the FCC Rules and with RSS-210 ofIndustry C...

39 1 1-2. Opening, closing and locking the doors Before driving Side doors The vehicle can be locked/unlocked using the wireless remote con- trol, key or door lock switch. ■ Wireless remote control (if equipped) → P. 36 ■ Key Regular Cab models Locks the door Unlocks the door Access Cab and Double C...

40 1-2. Opening, closing and locking the doors ■ Door lock switch (if equipped) Driver’s door lock switch Locks all doors Unlocks all doors Passenger’s door lock switch Locks all doors Unlocks all doors ■ Inside door lock button Locks the door Unlocks the door Pulling the inside handle canopen the f...

41 1-2. Opening, closing and locking the doors 1 Before driving Locking the front doors from the outside without a key Move the inside door lock button to the lock position. Close the door. Vehicles with power door lock system The door cannot be locked if a front door is open and the key is inthe en...

42 1-2. Opening, closing and locking the doors CAUTION ■ To prevent an accident Observe the following precautions while driving the vehicle.Failing to do so may result in a door opening and an occupant falling out,resulting in death or serious injury. ● Always use a seat belt. ● Always lock all door...

43 1 1-2. Opening, closing and locking the doors Before driving Access doors (Access Cab models only) NOTICE ■ When opening or closing the front door and access door The front door and access door could be damaged if they hit each otherwhen being opened or closed. The access door (rear door) can be ...

44 1-2. Opening, closing and locking the doors Tailgate Removing the tailgate ■ Before removing the tailgate (vehicles with rear view monitorsystem) These connector covers are used when removing the tailgate, toprevent the back-up camera wire harness connectors from beingcontaminated. Connector cove...

45 1-2. Opening, closing and locking the doors 1 Before driving To disconnect the wire harnessconnectors ( and ), press and hold the lock of the tailgatewire harness connector (White)and pull apart. Tailgate wire harness connec-tor (White) Frame wire harness connector(Gray) Attach the connector cove...

46 1-2. Opening, closing and locking the doors Pull out the wire harness fromthe vehicle bed. Attach the connector cover(Gray) to the tailgate wire har-ness connector (White). Tailgate wire harness connec-tor (White) Connector cover (Gray) ■ Removing the tailgate Open the tailgate to the anglewhere ...

47 1-2. Opening, closing and locking the doors 1 Before driving Slide the tailgate a little to theright to unhook the left side. To attach the tailgate, follow theremoval procedure in reverseorder. Rear step bumper For rear end protection and eas-ier step-up loading. To get on the rear step bumper,u...

48 1-2. Opening, closing and locking the doors NOTICE ■ To prevent damage to the tailgate wire harness (vehicles with rear viewmonitor system) Do not pull out all of the tailgate wire harness before open the tailgate. ■ To prevent damage to the camera lens (vehicles with rear view monitorsystem) Sto...

49 1 Before driving 1-3. Adjustable components (seats, mirrors, steering wheel) Front seats Bench type seat Seat position adjustmentlever Separated type seats Seat position adjustmentlever Driver’s seat lumbar sup-port adjustment knob(if equipped) Seatback angle adjustmentlever

50 1-3. Adjustable components (seats, mirrors, steering wheel) Moving passenger’s seat for rear seat entry (if equipped) Lift the seatback angle adjustinglever or press the pedal behindthe seatback. The seat will slideforward. Move the seat to the front-mostposition. ■ After passengers are in the ve...

51 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving Folding passenger’s seat (vehicles with seatback table) Pull the seatback angle adjustinglever and raise the seatback toits upright position. Pull the seatback folding leverand fold the seatback down.

52 1-3. Adjustable components (seats, mirrors, steering wheel) Active head restraints (Access Cab and Double Cab models only) When the occupant’s backpresses against the seatbackduring a rear-end collision, thehead restraint moves slightly for-ward to help reduce the risk ofwhiplash on the seat occu...

53 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving CAUTION ■ Seat adjustment ● Be careful that the seat does not hit passengers or luggage. ● Do not recline the seat more than necessary when the vehicle is in motionto reduce the risk of sliding under the lap belt. If the...

54 1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats (Access Cab and Double Cab models) Access Cab models The bottom cushion of the rear seats can be raised and lowered. ■ Before raising the bottom cushion Stow the seat belt buckles. This prevents the seat beltbuckles from falli...

55 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving Double Cab models The seatback of the rear seat can be folded. ■ Before folding rear seats Stow the rear seat belt buck-les. This prevents the seat beltbuckles from falling out whenyou fold the seatback. Pass the seat be...

57 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving CAUTION ■ When the seatback is folded/the bottom cushion is raised Do not sit on or place anything on the seatback or auxiliary box while driving. ■ When returning the seats to their original position Observe the followi...

58 1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Head restraints are provided for all seats. ■ Adjusting the head restraints Bench type front seat Up Pull the head restraints up. Down Push the head restraint downwhile pushing the lock releasebutton. Separated type front...

59 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving ■ Removing the front head restraints Bench type seat ■ When using the rear head restraints Access Cab models To use Lift up the head restraint until itlocks. To fold Pull the head restraint lockrelease lever to fold the ...

60 1-3. Adjustable components (seats, mirrors, steering wheel) Separated type seat ■ Removing the rear head restraints (Double Cab models only) ■ Installing the front head restraints Bench type seat Separated type seat Pull the head restraint up while pushingthe lock release button. Pull the head re...

61 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving ■ Installing the rear head restraints (Double Cab models only) ■ When installed the rear outboard head restraints to opposite direction(Double Cab models only) While pressing in the screwdriver, pull up the head restrain...

62 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Head restraint precautions Observe the following precautions regarding the head restraints. Failure todo so may result in death or serious injury. ● Use the head restraints designed for each respective seat. ● Adjust the head r...

63 1 1-3. Adjustable components (seats, mirrors, steering wheel) Before driving Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts ● Extend the shoulder belt sothat it comes fully over theshoulder, but does notcome into ...

64 1-3. Adjustable components (seats, mirrors, steering wheel) Seat belt pretensioners (front seats) The pretensioner helps the seatbelt to quickly restrain the occu-pant by retracting the seat beltwhen the vehicle is subjected tocertain types of severe frontalcollision or a vehicle rollover. The pr...

65 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving ■ Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may alsolock if you lean forward too quickly. A slow, easy motion will allow the belt toextend so that you can mo...

66 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Replacing the belt after the pretensioner has been activated If the vehicle is involved in multiple collisions, the pretensioner will activatefor the first collision, but will not activate for the second or subsequent colli-sions. ■ Se...

67 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving CAUTION ■ When children are in the vehicle Do not allow children to play with the seat belt. If the seat belt becomestwisted around a child’s neck, it may lead to chocking or other serious inju-ries that could result in ...

68 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Seat belt damage and wear ● Do not attempt to install, remove, modify, disassemble or dispose of theseat belts. Have any necessary repairs carried out by your Toyota dealer.Inappropriate handling of the pretensioner may prevent...

69 1 1-3. Adjustable components (seats, mirrors, steering wheel) Before driving Steering wheel CAUTION ■ Caution while driving Do not adjust the steering wheel while driving.Doing so may cause the driver to mishandle the vehicle and an accidentmay occur resulting in death or serious injury. ■ After ...

70 1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions. Manual anti-glare inside rear view mirror Normal position Anti-glare position

71 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving Auto anti-glare inside rear view mirror (type A) In automatic mode, sensors are used to detect the headlights ofvehicles behind and automatically reduces the reflected light. Turns automatic mode on/off The indicator com...

72 1-3. Adjustable components (seats, mirrors, steering wheel) Adjusting the height of rear view mirror Adjust the height of the rear viewmirror by moving it up and down. Auto anti-glare inside rear view mirror (type B) In automatic mode, sensors are used to detect the headlights ofvehicles behind a...

73 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving Inside rear view mirror display (vehicles with auto anti-glareinside rear view mirror) The inside rear view mirror displays the following information. Also, the display and display settings can be changed. ■ Compass → P....

75 1 1-3. Adjustable components (seats, mirrors, steering wheel) Before driving Outside rear view mirrors Mirror angle can be adjusted. Power-adjustable type Select a mirror to adjust. (L: left or R: right) Adjust the mirror up, down,in or out using the switch.

76 1-3. Adjustable components (seats, mirrors, steering wheel) Folding back the mirrors Push backward to fold the mir-rors. Manually adjustable type Adjust the mirror up, down, inor out by pushing the mirrorsurface. ■ Mirror operating conditions (vehicles with power-adjustable type only) The engine ...

77 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving CAUTION ■ When driving the vehicle Observe the following precautions while driving.Failing to do so may result in loss of control of the vehicle and cause an acci-dent, resulting in death or serious injury. ● Do not adju...

78 1-4. Opening and closing the windows Power windows ∗ Lock switch Press the switch down to lockpassenger window switches. Use this switch to prevent chil-dren from accidentally opening orclosing a passenger window. ∗ : If equipped The power windows can be opened/closed using the following switches...

79 1-4. Opening and closing the windows 1 Before driving ■ The power windows can be operated when The engine switch is in the ON position. ■ Operating the power windows after turning the engine off The power windows can be operated for approximately 43 seconds evenafter the engine switch is turned t...

80 1-4. Opening and closing the windows Back window (vehicles with sliding type) ■ Closing the back window Make sure that the back window is securely closed after closing it. CAUTION ■ While driving Keep the back window closed.This not only keeps personal belongings from being thrown out, but also p...

81 1 Before driving 1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle Turn the engine switch off and ensure that all the doors and win-dows are closed. ■ Opening the fuel tank cap Open the fuel filler door. Turn the fuel ta...

82 1-5. Refueling Closing the fuel tank cap When replacing the fuel tankcap, turn it until a clicking soundis heard. After releasing your hand, the capwill turn slightly to the oppositedirection. ■ Fuel types Use unleaded gasoline. (Octane Rating 87 [Research Octane Number 91] orhigher) ■ Fuel tank ...

83 1-5. Refueling 1 Before driving CAUTION ■ Refueling the vehicle ● Do not inhale vaporized fuel.Fuel contains substances that are harmful if inhaled. ● Do not smoke while refueling the vehicle.Doing so may cause the fuel to ignite and cause a fire. ● Do not return to the vehicle or touch any perso...

84 1-6. Theft deterrent system Engine immobilizer system ∗ ∗ : If equipped ■ System maintenance The vehicle has a maintenance-free type engine immobilizer system. ■ Conditions that may cause the system to malfunction ● If the key is in contact with a metallic object ● If the key is in close proximit...

85 1-6. Theft deterrent system 1 Before driving ■ Certifications for the engine immobilizer system For vehicles sold in U.S.A. FCC ID: MOZRI-21BTY This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions: (1) this device may not cause harmful interfer-e...

86 1-6. Theft deterrent system For vehicles sold in New Caledonia NOTICE ■ To ensure the system operates correctly Do not modify or remove the system. If modified or removed, the properoperation of the system cannot be guaranteed. “Hereby, Tokai Rika Co., Ltd., declares that this Immobilizer,model R...

87 1 Before driving 1-7. Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back inthe seat. ( → P. 49) Adjust the position of theseat forward or backward toensure the pedals can bereached and easilydepressed to the extentrequired. ( → P. 49) Adjust t...

89 1 1-7. Safety information Before driving SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. Front airbag...

90 1-7. Safety information Airbag system components Vehicles with bench type front seat Vehicles with separated type front seat

92 1-7. Safety information In certain types of severe frontal or side impacts, the SRS airbag sys-tem triggers the airbag inflators. A chemical reaction in the inflatorsquickly fills the airbags with non-toxic gas to help restrain the motionof the occupants. ■ SRS warning light This warning light sy...

93 1-7. Safety information 1 Before driving ● It is possible that in some collisions where the forward deceleration of thevehicle is very close to the designed threshold level, the SRS front air-bags and the seat belt pretensioners may not activate together. ● The SRS front passenger airbag will not...

96 1-7. Safety information ■ When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ● The front of the vehicle is damaged ordeformed, or was involved in an acci-dent that was not severe enough tocause th...

97 1-7. Safety information 1 Before driving CAUTION ■ SRS airbag precautions Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat beltsproperly.The SRS airbags are supplemental...

100 1-7. Safety information CAUTION ■ SRS airbag precautions ● Bench type front seat: Do not use a seat accessory, such as a cushion orseat cover, that covers the seat cushion surface. ● Do not use seat accessories which cover the parts where the SRS sideairbags inflate as they may interfere with in...

101 1-7. Safety information 1 Before driving CAUTION ■ Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modificationswithout consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causin...

102 1-7. Safety information Deactivating the curtain shield airbags in a vehicle rollover (4WD models only) On/off (hold for a few seconds) The RSCA OFF indicator turns on(only when the engine switch is inthe ON position.) The roll sensing function for thecurtain shield airbags and seatbelt pretensi...

103 1 1-7. Safety information Before driving Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the right front passenger seat and activates or deactivates the devices for the front pa...

104 1-7. Safety information Conditions and operation of the front passenger occupantclassification system ■ Adult* 1 ■ Child* 3 or child restraint system* 4 Indicator/ warning light AIR BAG ON and AIR BAG OFF indica- tor lights AIR BAG ON SRS warning light Off Front passenger’s seat belt reminder li...

105 1-7. Safety information 1 Before driving ■ Unoccupied ■ There is a malfunction in the system * 1 : The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may rec-ognize him/her as a child depending on his/her physique and pos-ture....

106 1-7. Safety information * 4 : Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should onlybe installed on the front passenger seat when it is unavoidable.( → P. 108) * 5 : In case the indicator is not illuminated, consult t...

107 1-7. Safety information 1 Before driving CAUTION ■ Front passenger occupant classification system precautions ● Do not recline the front passenger seatback so far that it touches a rearseat or a back wall. This may cause the AIR BAG OFF indicator light to beilluminated, which indicates that the ...

108 1-7. Safety information Child restraint systems Points to remember Studies have shown that installing a child restraint on a rear seat ismuch safer than installing one to the front passenger seat. ● Choose a child restraint system that suits your vehicle and isappropriate to the age and size of ...

109 1-7. Safety information 1 Before driving Forward facing — Convertible seat Booster seat ■ Selecting an appropriate child restraint system ● Use a child restraint system appropriate for the child until the childbecomes large enough to properly wear the vehicle’s seat belt. ● If a child is too lar...

110 1-7. Safety information CAUTION ■ Child restraint precautions ● For effective protection in automobile accidents and sudden stops, a childmust be properly restrained, using a seat belt or child restraint systemdepending on the age and size of the child. Holding a child in your arms isnot a subst...

112 1-7. Safety information Installing child restraints Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used ...

113 1-7. Safety information 1 Before driving ■ Using the seat belts Seat belts equipped with achild restraint locking mecha-nism (ALR/ELR belts exceptdriver’s seat belt) ( → P. 63) ■ Using the top tether strap Regular Cab models with bench type seat Anchor bracket (for top tetherstrap) Anchor bracke...

116 1-7. Safety information Installation with LATCH system (Access Cab models) Type A Latch the hooks of thelower straps onto theLATCH anchors andtighten the lower straps. If the child restraint has atop tether strap, the toptether strap should belatched onto the toptether strap anchor. For owners i...

117 1-7. Safety information 1 Before driving Type B Latch the buckles ontothe LATCH anchors. If the child restraint has atop tether strap, the toptether strap should belatched onto the toptether strap anchor. For owners in Canada:A symbol on a child restraint sys-tem indicates the presence of alower...

118 1-7. Safety information Installation with LATCH system (Double Cab models) Type A Widen the gap betweenthe seat cushion andseatback slightly. Latch the hooks of thelower straps onto theLATCH anchors andtighten the lower straps. If the child restraint has atop tether strap, the toptether strap sh...

119 1-7. Safety information 1 Before driving Type B Widen the gap betweenthe seat cushion andseatback slightly. Latch the buckles ontothe LATCH anchors. If the child restraint has atop tether strap, the toptether strap should belatched onto the toptether strap anchor. For owners in Canada:A symbol o...

120 1-7. Safety information Run the seat belt through thechild seat and insert the plateinto the buckle. Make sure thatthe belt is not twisted. Fully extend the shoulder beltand then allow it to retractslightly in order to activate theALR lock mode. Lock mode allows the seat belt toretract only. Whi...

124 1-7. Safety information Center passenger seat Route the top tether strapthrough the routing device asshown in the illustration. Make sure the top tether strap isnot twisted. Latch the hook onto theanchor bracket. Return the seatback to its orig-inal position. Make sure the seatback issecurely lo...

125 1-7. Safety information 1 Before driving ■ Separated type seat Remove the head restraint. Swing the seatback forwardslightly ( → P. 50) and remove the anchor bracket cover. Store the removed cover in a safeplace such as the glove box. Route the top tether strapthrough the routing device asshown ...

126 1-7. Safety information Replace the head restraint. Child restraint systems with a top tether strap (Access Cab models) Remove the anchor bracket cov-ers. Store the removed covers in asafe place such as the glove box. Secure the child restraint using a seat belt or lower anchors. Route the top t...

127 1-7. Safety information 1 Before driving Child restraint systems with a top tether strap (Double Cab models) Remove the head restraint. Installing position: Outside passenger seat Center passenger seat Outside passenger seat Swing the seatback forwardslightly. ( → P. 55) Latch the hook onto thea...

128 1-7. Safety information Secure the child restraint using a seat belt or lower anchors,and tighten the top tether strap. Make sure the top tether strap is securely latched. Replace the head restraint. Installing position: Outside passenger seat Center passenger seat ■ Laws and regulations pertain...

129 1-7. Safety information 1 Before driving CAUTION ■ When installing a booster seat Do not fully extend the shoulder belt to prevent the belt from going to ALRlock mode. ( → P. 65) ALR mode causes the belt to tighten only which could cause injury or dis-comfort to the child. ■ When installing a ch...

130 1-7. Safety information CAUTION ■ When installing a child restraint system ● When a booster seat is installed, always ensure that the shoulder belt ispositioned across the center of the child’s shoulder. The belt should bekept away from the child’s neck, but not so that it could fall off the chi...

132 2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. ■ Starting the engine → P. 143 ■ Driving Automatic transmission With the brake pedal depressed, shift the shift lever to D. ( → P. 146) Release the parking brake. ( → P. 154) Gradual...

133 2-1. Driving procedures 2 Wh en drivin g Starting on a steep uphill Automatic transmission With the brake pedal depressed, firmly set the parking brakeand shift the shift lever to D. Gently depress the accelerator pedal. Release the parking brake. ■ Parking the vehicle Automatic transmission Wit...

134 2-1. Driving procedures Manual transmission With the parking brake firmly set and the clutch pedal fullydepressed, shift the shift lever to 1. Lightly depress the accelerator pedal at the same time asgradually releasing the clutch pedal. Release the parking brake. ■ Driving in the rain ● Drive c...

135 2-1. Driving procedures 2 Wh en drivin g CAUTION ■ When starting the vehicle (vehicles with an automatic transmission) Always keep your foot on the brake pedal while stopped with the engine run-ning. This prevents the vehicle from creeping. ■ When driving the vehicle ● Do not drive if you are un...

138 2-1. Driving procedures CAUTION ■ When the vehicle is stopped ● If the vehicle is stopped on an incline, in order to prevent accidents causedby the vehicle rolling forward or backward, always depress the brake pedaland securely apply the parking brake as needed. ● Avoid revving or racing the eng...

139 2-1. Driving procedures 2 Wh en drivin g CAUTION ■ Exhaust gases Exhaust gases include harmful carbon monoxide (CO) that is colorless andodorless. Inhaling exhaust gases may lead to death or a serious health haz-ard. ● If the vehicle is in a poorly ventilated area, stop the engine. In a closedar...

140 2-1. Driving procedures CAUTION ■ When braking the vehicle ● Do not pump the brake pedal if the engine stalls. Each push on the brake pedal uses up the reserve for the power-assistedbrakes. ● The brake system consists of 2 individual hydraulic systems: If one of thesystems fails, the other will ...

141 2-1. Driving procedures 2 Wh en drivin g NOTICE ■ Avoiding damage to vehicle parts ● Do not turn the steering wheel fully in either direction and hold it there for along time. Doing so may damage the power steering pump. ● When driving over bumps in the road, drive as slowly as possible to avoid...

142 2-1. Driving procedures NOTICE ■ When encountering flooded roads Do not drive on a road that has flooded after heavy rain etc. Doing so maycause the following serious damage to the vehicle. ● Engine stalling ● Short in electrical components ● Engine damage caused by water immersion In the event ...

143 2-1. Driving procedures 2 Wh en drivin g Engine (ignition) switch ■ Engine switch LOCK The steering wheel is lockedand the key can be removed.(Vehicles with an automatictransmission: The key can beremoved only when the shiftlever is in P.) ACC Some electrical componentssuch as the audio system c...

144 2-1. Driving procedures ■ Turning the key from ACC to LOCK ■ Steering lock release ■ If the engine does not start (vehicles with engine immobilizer system) The engine immobilizer system may not have been deactivated. ( → P. 84) ■ Key reminder function A buzzer sounds if the driver’s door is open...

145 2-1. Driving procedures 2 Wh en drivin g CAUTION ■ Caution while driving Do not turn the engine switch to the LOCK position.If in an emergency, you must turn the engine off while the vehicle is moving,turn the engine switch only to the ACC position. NOTICE ■ To prevent battery discharge Do not l...

146 2-1. Driving procedures Automatic transmission ∗ ∗ : If equipped Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever 5-speed models While the engine switch is on, depress the brake pedal andmove the shift lever.

147 2-1. Driving procedures 2 Wh en drivin g 4-speed models While the engine switch is on, depress the brake pedal andmove the shift lever. ■ Shift position uses * : To improve fuel consumption and reduce noises, set the shift lever inD for normal driving. Shift position Function 5-speed models 4-sp...

148 2-1. Driving procedures ■ Downshifting restrictions The shift lever cannot be downshifted if the following speeds are exceeded. 2WD models mph (km/h) 4WD models mph (km/h) Downshifting Maximum speed 5-speed models 4-speed models 4 → 3 81 (130) — 3 → 2 56 (90) 71 (115) 2 → L 22 (35) 34 (55) Downs...

149 2-1. Driving procedures 2 Wh en drivin g ■ When driving with the cruise control system (if equipped) The engine brake will not operate when downshifting from D to 4 (5-speedmodels) or 3 (4-speed models). ( → P. 174) ■ If the shift lever cannot be shifted from P → P. 533 ■ AI-SHIFT AI-SHIFT autom...

150 2-1. Driving procedures Manual transmission ∗ ∗ : If equipped ■ Shifting the shift lever 6-speed models Fully depress the clutch pedal before operating the shift lever, andthen release it slowly. 5-speed models Fully depress the clutch pedal before operating the shift lever, andthen release it s...

151 2-1. Driving procedures 2 Wh en drivin g ■ Maximum allowable speed Observe the following maximum allowable speeds in each gear when maxi-mum acceleration is necessary. 2WD models except PreRunner mph (km/h) PreRunner mph (km/h) Shift position Maximum speed 6-speed models 5-speed models 1 32 (52)...

153 2-1. Driving procedures 2 Wh en drivin g Turn signal lever ■ Turn signals can be operated when The engine switch is in the ON position. ■ If the indicators flash faster than usual Check that a light bulb in the front or rear turn signal lights has not burnedout. Right turn Left turn Move and hol...

154 2-1. Driving procedures Parking brake Lever type ● Sets the parking brake Fully set the parking brakewhile depressing the brakepedal. At this time, the indicator willcome on. ● Release the parking brake Press the button Turn the lever clockwise Press it in completely Pedal type Sets the parking ...

155 2-1. Driving procedures 2 Wh en drivin g ■ Parking brake engaged warning buzzer The buzzer sounds to indicate that parking brake is still engaged (with thevehicle having reach a speed of 3 mph [5 km/h]). ■ Usage in winter time See “Winter driving tips” for parking brake usage in winter time. ( →...

156 2-1. Driving procedures Horn ■ After adjusting the steering wheel Make sure that the steering wheel is securely locked.The horn may not sound if the steering wheel is not securely locked. ( → P. 69) To sound the horn, press on orclose to the mark.

157 2 Wh en drivin g 2-2. Gauges and meters Gauges and meters The following gauges, meters and displays illuminate when theengine switch is in the ON position. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Engine coolant temperature gauge Dis...

158 2-2. Gauges and meters Odometer and trip meter display button Pressing this button switches between odometer and trip meter dis-plays. Odometer Trip meter A * Trip meter B * * :Pushing and holding the button will reset the trip meter. Instrument panel light control The brightness of the instrume...

159 2-2. Gauges and meters 2 Wh en drivin g NOTICE ■ To prevent damage to the engine and its components ● Do not let the indicator needle of the tachometer enter the red zone, whichindicates the maximum engine speed. ● The engine may be overheating if the engine coolant temperature gauge isin the re...

160 2-2. Gauges and meters Indicators and warning lights The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. Instrument cluster Center panel

161 2-2. Gauges and meters 2 Wh en drivin g ■ Indicators The indicators inform the driver of the operating state of thevehicle’s various systems. Turn signal indicator ( → P. 153) * 1,2 Slip indicator( → P. 190, 192, 201) Headlight high beam indicator ( → P. 165) * 1 VSC OFF indicator( → P. 192, 202...

162 2-2. Gauges and meters ■ Warning lights Warning lights inform the driver of malfunctions in any of thevehicle’s systems. ( → P. 505) * 1 : These lights turn on when the engine switch is turned to the ON position to indicate that a system check is being performed. Theywill turn off after the engi...

163 2-2. Gauges and meters 2 Wh en drivin g CAUTION ■ If a safety system warning light does not come on Should a safety system light such as ABS and the SRS airbag warning lightnot come on when you start the engine, this could mean that these systemsare not available to help protect you in an accide...

164 2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually. Turning the end of the lever turns on the lights as follows: Type A OFFVehicles with day-time running lightsystem: The daytimerunning lights turnon. The side marker,parking, tail, licenseplate, daytime...

165 2-3. Operating the lights and wipers 2 Wh en drivin g Turning on the high beam headlights With the headlights on, pushthe lever forward to turn on thehigh beams. Pull the lever back to the centerposition to turn the high beamsoff. Pull the lever toward you toturn on the high beams. Release the l...

166 2-3. Operating the lights and wipers ■ Daytime running light system (if equipped) ● To make your vehicle more visible to other drivers, the front turn signallights turn on automatically whenever the engine is started and the park-ing brake is released. Daytime running lights are not designed for...

167 2-3. Operating the lights and wipers 2 Wh en drivin g Fog light switch ∗ ∗ : If equipped ■ The fog lights can be turned on only when The headlights are on low beam. The fog lights improve visibility in difficult driving conditions, such as in rain or fog. On/off

168 2-3. Operating the lights and wipers Windshield wipers and washer ■ Without intermittent type Type A Low speed wind-shield wiper opera-tion High speed wind-shield wiper opera-tion Temporary operation Washer operation

170 2-3. Operating the lights and wipers ■ Intermittent wiper with interval adjuster Wiper intervals can be adjusted for intermittent operation (when or is selected). Type A Intermittent wind-shield wiper opera-tion Low speed wind-shield wiper opera-tion High speed wind-shield wiper opera-tion Tempo...

172 2-3. Operating the lights and wipers ■ The windshield wiper and washer can be operated when The engine switch must be in the ON position. ■ If no windshield washer fluid sprays Check that the washer nozzles are not blocked and if there is washer fluid inthe windshield washer fluid reservoir. Inc...

173 2-3. Operating the lights and wipers 2 Wh en drivin g NOTICE ■ When the windshield is dry Do not use the wipers, as they may damage the windshield. ■ When there is no washer fluid spray from the nozzle Damage to the washer fluid pump may be caused if the lever is pulledtoward you and held contin...

174 2-4. Using other driving systems Cruise control ∗ ∗ : If equipped Use the cruise control to maintain a set speed without depressing the accelerator pedal. Indicator Cruise control switch ■ Setting the vehicle speed Press the ON-OFF button toactivate the cruise control. Cruise control indicator w...

175 2-4. Using other driving systems 2 Wh en drivin g ■ Adjusting the set speed To change the set speed, operate the lever until the desired setspeed is obtained. Increases the speed Decreases the speed Fine adjustment: Momentarilymove the lever in the desireddirection. Large adjustment: Hold thelev...

177 2-4. Using other driving systems 2 Wh en drivin g CAUTION ■ To avoid operating the cruise control by mistake Switch the cruise control off using the ON-OFF button when not in use. ■ Situations unsuitable for cruise control Do not use cruise control in any of the following situations.Doing so may...

178 2-4. Using other driving systems Rear view monitor system (vehicles with auto anti-glare inside rear view mirror) The rear view monitor system assists the driver by displaying an image of the area behind the vehicle. The image is displayed in reverse on the screen. This reversed image is a simil...

179 2-4. Using other driving systems 2 Wh en drivin g ■ The rear view monitor system can be operated when The shift lever is in R and engine switch is ON. ■ Switching the screen on/off mode The rear view monitor display on the inside rear view mirror can be turnedon/off. Type A: Press and hold to di...

180 2-4. Using other driving systems ■ Displayed area ■ Rear view monitor guide lines ● Guide lines are displayed on the monitor. Vehicle width extension guide lines (blue)These lines indicate the estimated vehicle width extension. Distance guide line (blue)This line indicates a position on the grou...

181 2-4. Using other driving systems 2 Wh en drivin g ■ Driving precautions When the grade behind the vehicleslopes up sharply, objects appear to befarther away than they actually are. When the grade behind the vehicleslopes down sharply, objects appear tobe closer than they actually are.

183 2-4. Using other driving systems 2 Wh en drivin g ■ Rear view monitor system camera ■ Smear effect The rear view monitor system camera islocated on the tailgate as shown in theillustration. In the following cases, it may become dif-ficult to see the images on the screen,even when the system is f...

184 2-4. Using other driving systems ■ Flicker effect When the camera is used under fluorescent lights, sodium lights, mercurylights etc., the lights and the illuminated areas may appear to flicker. CAUTION ■ When using the rear view monitor system Observe the following precautions to avoid an accid...

185 2-4. Using other driving systems 2 Wh en drivin g NOTICE ■ Handling of the camera ● As the camera has a water proof construction, do not detach, disassembleor modify it. This may cause incorrect operation. ● If the camera lens becomes dirty, it cannot transmit a clear image. If waterdroplets, sn...

186 2-4. Using other driving systems Four-wheel drive system ∗ ∗ : If equipped Use the front-wheel drive control switch to select the following transfer modes. H2 (high speed position,two-wheel drive) Use this for normal drivingon dry hard-surfaced roads.This position gives greatereconomy, quietest ...

187 2-4. Using other driving systems 2 Wh en drivin g Shifting between H4 and L4 ■ Shifting from H4 to L4 Automatic transmission Stop the vehicle completely with brake pedal help down. Shift the shift lever to N. Push and turn the front-wheel drive control switch fully clock-wise.If the four-wheel d...

188 2-4. Using other driving systems ■ Shifting between H2 and H4 ● Shifting from H2 to H4 Reduce the vehicle speed to less than 62 mph (100 km/h) and turn thefront-wheel drive control switch fully clockwise. ● Shifting from H4 to H2 Turn the front-wheel drive control switch fully counterclockwise.T...

189 2-4. Using other driving systems 2 Wh en drivin g ■ Shifting to L4 VSC is automatically turned off. ■ Four-wheel drive usage frequency You should drive in four-wheel drive for at least 10 miles (16 km) eachmonth.This will assure that the front-drive components are lubricated. CAUTION ■ Caution w...

190 2-4. Using other driving systems Active traction control system ∗ When the active traction control system is operating If four wheels spin, the slip indi-cator flashes to indicate that theactive traction control systemhas been engaged. ∗ : If equipped The active traction control system automatic...

191 2-4. Using other driving systems 2 Wh en drivin g ■ When the rear differential is locked (vehicles with the rear differentiallock system) The active traction control system is activated only when the vehicle speedis less than 3 mph (6 km/h). ■ Sounds and vibrations caused by the active traction ...

192 2-4. Using other driving systems AUTO LSD system When the AUTO LSD system is operating If the rear wheels spin, the slipindicator flashes to indicate thatthe AUTO LSD system has beencontrolled the spinning of therear wheels. The AUTO LSD system aids traction by using the traction control system ...

193 2-4. Using other driving systems 2 Wh en drivin g ■ If the engine is turned off and restarted The AUTO LSD system and the indicators are automatically turned off. ■ Reactivation of the VSC system linked to vehicle speed When the AUTO LSD system is turned on, the VSC system will turn on auto-mati...

194 2-4. Using other driving systems Rear differential lock system ∗ Using the rear differential lock system Automatic transmission 4WD models: Before using the rear differential lock system.Stop the vehicle, shift the shift lever to N and put the front-wheel drive control switch in the L4 position ...

195 2-4. Using other driving systems 2 Wh en drivin g Manual transmission 4WD models: Before using the rear differential lock system.Stop the vehicle or reduce your speed to less than 2 mph (3km/h). Depress the clutch pedal and put the front-wheel drivecontrol switch in the L4 position to see if thi...

196 2-4. Using other driving systems ■ After unlocking the rear differential To check that the indicator goes off, turn the engine switch to the ON posi-tion, but do not start the engine. CAUTION ■ To avoid an accident ● Do not use the rear differential lock system except when wheel spinningoccurs i...

197 2-4. Using other driving systems 2 Wh en drivin g Downhill Assist Control system ∗ ∗ : If equipped The downhill assist control system helps to prevent excessive speed on steep downhill descents. ■ System operation The system will operate when the vehicle is traveling under 15mph (25 km/h) and th...

199 2-4. Using other driving systems 2 Wh en drivin g Clutch start cancel switch ∗ ∗ : If equipped ■ Clutch start system The system is designed to keep the starter motor from operating if the clutchpedal is not depressed all the way down. The switch allows the vehicle to be driven out of difficult s...

200 2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when ...

202 2-4. Using other driving systems To disable VSC, Trailer Sway Control and TRAC (2WD modelsand 2WD mode on 4WD models) If the vehicle gets stuck in fresh snow or mud, VSC, Trailer SwayControl and TRAC may reduce power from the engine to the wheels.You may need to turn the system off to enable you...

203 2-4. Using other driving systems 2 Wh en drivin g To disable VSC, Trailer Sway Control and/or TRAC (4WD modeon 4WD models) If the vehicle gets stuck in fresh snow or mud, VSC, Trailer SwayControl and TRAC may reduce power from the engine to the wheels.You may need to turn the system off to enabl...

204 2-4. Using other driving systems ■ When the TRAC OFF indicator light comes on even if the VSC OFFswitch has not been pressed TRAC, hill-start assist control, downhill assist control system cannot be oper-ated. Contact your Toyota dealer. ■ Reactivation of the TRAC, VSC and Trailer Sway Control s...

206 2-4. Using other driving systems CAUTION ■ Replacing tires Make sure that all tires are of the same size, brand, tread pattern and totalload capacity. In addition, make sure that the tires are inflated to the appro-priate tire pressure level. The ABS, VSC, TRAC and Trailer Sway Control will not ...

207 2 Wh en drivin g 2-5. Driving information Off-road precautions (4WD models and PreRunner) Off-road vehicle feature ● Specific design characteristics give it a higher center of gravitythan ordinary passenger cars. This vehicle design feature causesthis type of vehicle to be more likely to rollove...

208 2-5. Driving information CAUTION ■ Off-road vehicle precautions Always observe the following precautions to minimize the risk of serious per-sonal injury or damage to your vehicle: ● In a rollover crash, an unbelted person is significantly more likely to diethan a person wearing a seat belt. The...

209 2-5. Driving information 2 Wh en drivin g Off-road driving When driving your vehicle off-road, please observe the following pre-cautions to ensure your driving enjoyment and to help prevent theclosure of areas to off-road vehicles. ● Drive your vehicle only in areas where off-road vehicles are p...

210 2-5. Driving information CAUTION ■ Off-road driving precautions Always observe the following precautions to minimize the risk of seriousinjury or damage to your vehicle: ● Drive carefully when off the road. Do not take unnecessary risks by drivingin dangerous places. ● Do not grip the steering w...

211 2-5. Driving information 2 Wh en drivin g NOTICE ■ To prevent the water damage ● Take all necessary safety measures to ensure that water damage to theengine or other components does not occur. ● Water entering the engine air intake will cause severe engine damage. ● Water entering the automatic ...

212 2-5. Driving information Cargo and luggage CAUTION ■ When you secure cargo with the deck rails Be sure to follow the instructions below in order to avoid the cargo com-ing loose. ● Do not install accessories (tie-down cleats, storage boxes, etc.) atmore than the following number of locations per...

213 2-5. Driving information 2 Wh en drivin g Capacity and distribution Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) − (Total weight of occupants) Steps for Determining Correct Load Limit— (1) Locate the statement “The combined weight of occup...

214 2-5. Driving information (6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine howthis reduces the available cargo and luggage load capacity of yourvehicle. Example on your vehicle Cargo capacity Total load capa...

215 2-5. Driving information 2 Wh en drivin g CAUTION ■ Things that must not be carried in the luggage compartment The following things may cause a fire if loaded in the luggage compart-ment. ● Receptacles containing gasoline ● Aerosol cans ■ Storage precautions Observe the following precautions.Fai...

217 2-5. Driving information 2 Wh en drivin g Vehicle load limits ■ Total load capacity and seating capacity These details are also described on the tire and loading informationlabel. ( → P. 461) Vehicle load limits include total load capacity, seating capacity, TWR (Trailer Weight Rating) and cargo...

218 2-5. Driving information CAUTION ■ Overloading the vehicle Do not overload the vehicle.It may not only cause damage to the tires, but also degrade steering andbraking ability, resulting in an accident.

219 2-5. Driving information 2 Wh en drivin g Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations ● Use fluids that are approp...

220 2-5. Driving information Selecting tire chains Use the correct tire chain size when mounting the snow chains.Chain size is regulated for each tire size. Side chain 0.2 in. (5 mm) in diameter Cross chain 0.25 in. (6.3 mm) in diameter Regulations on the use of snow chains ● Regulations regarding t...

221 2-5. Driving information 2 Wh en drivin g ■ Snow chain installation Observe the following precautions when installing and removing chains. ● Install and remove tire chains in a safe location. ● Install tire chains on the rear tires only. Do not install tire chains on thefront tires. ● Install ti...

222 2-5. Driving information CAUTION ■ When parking the vehicle Always use wheel blocks when parking without the parking brake. Failure todo so may allow the vehicle to move, resulting in an accident. NOTICE ■ Repairing or replacing snow tires Request repairs of and obtain replacement snow tires fro...

223 2-5. Driving information 2 Wh en drivin g Trailer towing Your vehicle is designed primarily as a passenger-and-load-carrying vehicle. Towing a trailer can have an adverse impact on handling, performance, braking, durability, and fuel consumption. For your safety and the safety of others, you mus...

224 2-5. Driving information Towing related terms ■ GCWR (Gross Combination Weight Rating) The maximum allowable grosscombination weight. The grosscombination weight is the sum ofthe total vehicle weight (includingthe occupants, cargo and anyoptional equipment installed onthe vehicle) and the weight...

225 2-5. Driving information 2 Wh en drivin g ■ GAWR (Gross Axle Weight Rating) The maximum allowable grossaxle weight. The gross axleweight is the load placed oneach axle (front and rear). ■ TWR (Trailer Weight Rating) The maximum allowable grosstrailer weight. The gross trailerweight is the sum of...

227 2-5. Driving information 2 Wh en drivin g Weight limits ● The gross trailer weight must never exceed the TWR described inthe table. ( → P. 228, 551) ● The gross combination weight must never exceed the GCWRdescribed in the table. ( → P. 228) Regular Cab models and Double Cab models ● The gross v...

231 2-5. Driving information 2 Wh en drivin g *1 : The model code is indicated on the Certification Label. ( → P. 227 , 553) *2 : Without towing package *3 : With towing package ■ Unbraked TWR * 1000 lb. (450 kg) ■ Fifth wheel and gooseneck towing TWR * Toyota does not recommend fifth wheel and goos...

232 2-5. Driving information Trailer Tongue Weight ● A recommended tongue weight varies in accordance with the typesof trailers or towing as described below. ● To ensure the recommended values shown below, the trailer mustbe loaded by referring to the following instructions. • Tongue Weight The gros...

233 2-5. Driving information 2 Wh en drivin g Hitch Trailer hitch assemblies have different weight capacities. Toyota rec-ommends the use of Toyota hitch/bracket for your vehicle. For details,contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only...

234 2-5. Driving information Selecting trailer ball Use the correct trailer ball for your application. Trailer ball load rating Matches or exceeds the grosstrailer weight rating of the trailer. Ball diameter Matches the size of the trailercoupler. Most couplers arestamped with the required trailerba...

235 2-5. Driving information 2 Wh en drivin g Positions for towing hitch receiver and hitch ball Weight carrying ball position:56.1 in. (1425 mm) Hitch receiver pin hole posi-tion: 44.2 in. (1123 mm) Connecting trailer lights Vehicles with 7 pin connector Use the wire harness stored inthe rear end u...

236 2-5. Driving information Trailer towing tips Your vehicle will handle differently when towing a trailer. Help to avoidan accident, death or serious injury, keep the following in mind whentowing: ● Speed limits for towing a trailer vary by state or province. Do notexceed the posted towing speed l...

237 2-5. Driving information 2 Wh en drivin g ● Reversing with a trailer attached is difficult and requires practice.Grip the bottom of the steering wheel and move your hand to theleft to move the trailer to the left. Move your hand to the right tomove the trailer to the right. (This is generally op...

239 2-5. Driving information 2 Wh en drivin g Release the parking brake (and also the brake pedal on vehi-cles with an automatic transmission), and slowly pull or backaway from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks. ■ Matching trailer ball height to trailer co...

240 2-5. Driving information ● The rear view mirrors conform to all applicable federal, state/provincial orlocal regulations. If they do not, install rear view mirrors appropriate fortowing purposes. ■ Break-in schedule If your vehicle is new or equipped with any new power train components(such as a...

241 2-5. Driving information 2 Wh en drivin g ● After the trailer swaying has stopped: • Stop in a safe place. Get all occupants out of the vehicle.• Check the tires of the vehicle and the trailer.• Check the load in the trailer. Make sure the load has not shifted.Make sure the tongue weight is appr...

242 2-5. Driving information CAUTION ■ To avoid accident or injury ● Do not exceed 65 mph (104 km/h), the posted towing speed limit or thespeed limit for your trailer as set forth in your trailer owner’s manual,whichever is lowest. Slow down sufficiently before making a turn, in crosswinds, on wet o...

243 2-5. Driving information 2 Wh en drivin g CAUTION ■ When towing a trailer Toyota recommends trailers with brakes that conform to any applicable fed-eral and state/provincial regulations. ● If the gross trailer weight exceeds unbraked TWR, trailer brakes arerequired. Toyota recommends trailers wi...

244 2-5. Driving information Dinghy towing NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground. Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

248 3-1. Using the air conditioning system and defogger Air conditioning system Adjusting the settings ■ Adjusting the temperature setting Turn the temperature control dial clockwise (warm) or counter-clockwise (cool). If is not pressed, the system will blow ambient temperature air or heated air. Fo...

249 3-1. Using the air conditioning system and defogger 3 In te ri o r a n d exte ri or fe at u res ■ Selecting the air outlets Set the air outlet selection dial to an appropriate position. The positions between the air outlet selections shown below can also beselected for more detailed adjustment. ...

250 3-1. Using the air conditioning system and defogger When the dial is set to , air flows to the feet and the wind-shield defogger operates. The air intake selector is automat-ically set to outside air mode. To return the recirculated air mode, press . Double Cab models only When the dial is set t...

251 3-1. Using the air conditioning system and defogger 3 In te ri o r a n d exte ri or fe at u res ■ If the ambient temperature drops while using the recirculatedair mode The air intake mode automatically changes from recirculated airmode to outside air mode after a few minutes. To cancel this func...

252 3-1. Using the air conditioning system and defogger Right and left side outlets Direct air flow to the left or right,up or down. Opening and closing the air outlets Center outlets Open the vent. Close the vent.

253 3-1. Using the air conditioning system and defogger 3 In te ri o r a n d exte ri or fe at u res Right and left side outlets Open the vent. Close the vent. ■ For quick clearing of the windshield and side windows Press to turn the air conditioning on. ■ Using the system in recirculated air mode Th...

254 3-1. Using the air conditioning system and defogger CAUTION ■ To prevent the windshield from fogging up Do not set the air outlet selection dial to during cool air operation in extremely humid weather. The difference between the temperature of theoutside air and that of the windshield can cause ...

255 3 In te ri o r a n d exte ri or fe at u res 3-2. Using the audio system Audio system types With Display Audio system Owners of models equipped with a Display Audio system shouldrefer to the “Display Audio System Owner’s Manual”. Without Display Audio system Type A: CD player with changer control...

256 3-2. Using the audio system Type B: CD player with changer controller and AM/FM radio Title Page Using the radio P. 260 Using the CD player P. 267 Playing MP3 and WMA discs P. 273 Operating an iPod P. 280 Operating a USB memory P. 288 Optimal use of the audio system P. 295 Using the AUX port P. ...

257 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res Language settings Vehicles with Display Audio system Refer to “Display Audio System Owner’s Manual”. Vehicles without Display Audio system (type B only) The language used for all voice guidance, voice recognition and mes-sag...

258 3-2. Using the audio system ■ About Bluetooth ® (vehicles with Display Audio system) CAUTION ■ For vehicles sold in U.S.A. and Canada Vehicles without Display Audio system ● Part 15 of the FCC Rules FCC Warning:Any unauthorized changes or modifications to this equipment will void theuser’s autho...

259 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res CAUTION Vehicles with Display Audio system Properly shielded a grounded cables and connectors must be used forconnection to host computer and/or peripherals in order to meet FCCemission limits. This transmitter must not be c...

260 3-2. Using the audio system Using the radio Type A Type B Volume Scanning for receivable stations Station selector Seeking the frequency Adjusting the frequency (AM, FM mode) or channel (SAT mode) AM ⋅ SAT/FM mode buttons Power Displaying radio text messages Changing the channel AM/FM/SAT mode b...

261 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res Setting station presets (excluding XM ® Satellite Radio) Search for desired stations by turning or or pressing “ ∧ ” or “ ∨ ” on . Press and hold a button (from to ) until you hear a beep. Type B only: Each time is pressed, ...

266 3-2. Using the audio system Contact the XM ® Listener Care Center at 1-800-967-2346 (U.S.A.) or 1-877- 209-0079 (Canada) ■ Certifications for the radio tuner This equipment has been tested and found to comply with the limits for aclass B digital device, pursuant to Part 15 of the FCC Rules. Thes...

267 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res Using the CD player Type A Type B Selector buttons Playback CD eject Fast-forwarding and reversing/ Selecting a track Searching playback Volume Power Selecting a track Displaying text messages Fast-forwarding and reversing/S...

268 3-2. Using the audio system Loading CD Insert a CD. Ejecting CD Press and remove the CD. Selecting a track Turn or or press “ ∧ ” or “ ∨ ” on to select the desired track. Fast-forwarding and reversing tracks Press and hold “ ∧ ” or “ ∨ ” on . Scanning tracks Press or . The first 10 seconds of ea...

271 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res NOTICE ■ CDs and adapters that cannot be used Do not use the following types of CDs, 3 in. (8 cm) CD adapters or DualDiscs.Doing so may damage the CD player and/or the CD insert/eject function. ● CD player with changer and A...

272 3-2. Using the audio system NOTICE ■ CD player precautions Failure to follow the precautions below may result in serious damage to theCDs or the player itself. ● Do not insert anything other than CDs into the CD slot. ● Do not apply oil to the CD player. ● Store CDs away from direct sunlight. ● ...

273 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res Playing MP3 and WMA discs Type A Type B Selecting a folder Volume Power Playback Searching playback Selecting a file Displaying text messages CD eject Selector buttons Fast-forwarding and reversing/Selecting a file Fast-forw...

274 3-2. Using the audio system Loading and ejecting MP3 and WMA discs → P. 268 Selecting and scanning a folder ■ Selecting folders one at a time Press “ ∧ ” or “ ∨ ” on to select the desired folder. ■ Scanning the first file of all the folders Press and hold or until you hear a beep. The first 10 s...

276 3-2. Using the audio system Switching the display Press or . Each time or is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time. ■ Error messages “CD CHECK”: This indicates a problem either with the CD or...

277 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res ■ MP3 and WMA files MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by usingMP3 compression. WMA (Windows Media Audio) is a Microsoft ® aud...

279 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res ● Extensions If the file extensions .mp3 and .wma are used for files other than MP3 andWMA files, they will be mistakenly recognized and played as MP3 andWMA files. This may result in large amounts of interference and damage...

280 3-2. Using the audio system Operating an iPod ∗ ∗ : If equipped Connecting an iPod enables you to enjoy music from the vehicle speakers. ■ Connecting an iPod Open the cover and connectan iPod using an iPod cable. Turn on the power of the iPod ifit is not turned on. Press .

281 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res ■ Control panel Fast-forwarding and reversing/Selecting a song Playback Selector knob Selector buttons Volume Power Displaying text messages Playback/pause

282 3-2. Using the audio system Selecting a play mode Press (BROWSE) to select iPod menu mode. Press , , or as that corresponds to the desired play mode. Press (MORE) to change to the second selection list. ■ Play mode list Depending on the model, the name of your iPod may be displayed atthe top of ...

283 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res ■ Selecting a list Turn to display the first selection list. Press to select the desired item. Pressing that corresponds to “MORE” changes to the second selection list. Repeat the same procedure to select the desired song na...

285 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res ■ About iPod ● Apple is not responsible for the operation of this device or its compliancewith safety and regulatory standards. ● iPod is a trademark of Apple Inc., registered in the U.S. and other coun-tries. ■ iPod functio...

286 3-2. Using the audio system ■ Compatible models Depending on differences between models or software version etc., somemodels listed above might be incompatible with this system.iPod 4th generation and earlier models are not compatible with this system.iPhone, iPod mini, iPod shuffle and iPod pho...

287 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res NOTICE ■ To prevent damage to iPod ● Do not leave iPod in the vehicle. The temperature inside the vehicle maybecome high, resulting in damage to the player. ● Do not push down on or apply unnecessary pressure to the iPod whi...

288 3-2. Using the audio system Operating a USB memory ∗ ∗ : If equipped Connecting a USB memory enables you to enjoy music from the vehicle speakers. ■ Connecting a USB memory Open the cover and connect aUSB memory. Turn on the power of the USBmemory if it is not turned on. Press .

290 3-2. Using the audio system Selecting and scanning files ■ Selecting a file Turn or press “ ∧ ” or “ ∨ ” on to select the desired file. ■ Scanning the files in a folder Press . The first 10 seconds of each file will be played. To cancel, press again. When the desired file is reached, press again...

291 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res Repeat play ■ Repeating a file Press (RPT). To cancel, press the button twice. ■ Repeating all the files in a folder Press (RPT) twice. To cancel, press the button again. Switching the display Press . Each time is pressed, t...

292 3-2. Using the audio system ■ USB memory ● Compatible device USB memory that can be used for MP3 and WMA playback. Depending on the type of USB device, playback may not be possible. ● Compatible device formats The following device formats can be used: • USB communication formats: USB2.0 FS (12 m...

294 3-2. Using the audio system ● Extensions If the file extensions .mp3 and .wma are used for files other than MP3 andWMA files, they will be mistakenly recognized and played as MP3 andWMA files. This may result in large amounts of interference and damageto the speakers. ● Playback • To play MP3 fi...

295 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res Optimal use of the audio system Type A Type B Adjusting the sound quality and ASL Menu button Selector buttons Selector knob

297 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res ■ Adjusting sound quality Type A: Turning adjusts the level. *: The sound quality level is adjusted individually in each radio mode or CD mode. Mode displayed Sound qual- ity mode Level Turn to the left Turn to the right BAS...

298 3-2. Using the audio system Type B: Turning adjusts the level. *: The sound quality level is adjusted individually in each audio mode. ■ Adjusting the Automatic Sound Levelizer (ASL) Type A: When “ASL” is selected, turning to the right changes the “ASL” level in the order of “LOW”, “MID” and “HI...

299 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res Type B: Press . Press (MORE). Press (ASL). Press , , or as corresponds to the desired mode (OFF, LOW, MID, or HIGH). ASL automatically adjusts the volume and tone quality according tovehicle speed. ■ Setting the number of pr...

300 3-2. Using the audio system Operating the sub woofer (on some Access Cab models) OFF ON LIGHT ON The sub woofer illuminationturns on. In this position, thesub woofer operates.

301 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res Using the AUX port This adapter can be used to connect a portable audio device and lis- ten to it through the vehicle’s speakers. Open the cover and connect the portable audio device. Type A

303 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res Using the steering wheel audio switches ∗ ∗ : If equipped Some audio features can be controlled using the switches on the steering wheel. Increases/decreases vol-ume Radio mode: Selects radiostation CD mode: Selects track/fi...

305 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res Selecting a track/file or song Press to select the CD, iPod, USB memory or Blue- tooth ® audio mode. Press “ ∨ ” or “ ∧ ” on to select the desired track/file or song. Selecting a folder or album Press to select the CD, USB m...

306 3-2. Using the audio system Detachable pole antenna The antenna can be removed. ■ Removing the antenna Place the included wrencharound the antenna. When not in use, the wrench isstored in glove box. Loosen the antenna with thewrench and remove it.

307 3-2. Using the audio system 3 In te ri o r a n d exte ri or fe at u res ■ About the wrench ● A standard 5/16 in. (8 mm) wrench can also be used to install or removethe antenna. ● After using the included wrench, store it in the glove box for safekeeping. ■ Installing the antenna Tighten the ante...

308 3-2. Using the audio system NOTICE ■ To avoid damaging the antenna Remove the antenna in the following situations. ● When using an automatic carwash. ● When the antenna will touch the ceiling of a garage, etc. ● When covering the vehicle with a car cover. ■ Removing the antenna ● For normal driv...

309 3 In te ri o r a n d exte ri or fe at u res 3-3. Using the Bluetooth ® audio system Bluetooth ® audio system ∗ ∗ : If equipped ■ Conditions under which the system will not operate ● If using a portable player that does not support Bluetooth ® ● If the portable player is switched off ● If the por...

310 3-3. Using the Bluetooth ® audio system ■ About Bluetooth ® ■ Compatible models ● Bluetooth ® specifications: Ver. 1.2 ● Following Profiles: • A2DP (Advanced Audio Distribution Profile) Ver. 1.0• AVRCP (Audio/Video Remote Control Profile) Ver. 1.0 or higher (Ver. 1.3 or higher recommended) Porta...

311 3-3. Using the Bluetooth ® audio system 3 In te ri o r a n d exte ri or fe at u res CAUTION ■ FCC WARNING Changes or modifications in construction not expressly approved by theparty responsible for compliance could void the user’s authority to operatethe equipment.Radio frequency exposure. This ...

312 3-3. Using the Bluetooth ® audio system Using the Bluetooth ® audio system ∗ ∗ : If equipped ■ Audio unit Display A message, name, number,etc. is displayed. Lower-case characters andspecial characters cannotbe displayed. Displays information that istoo long to be displayed atone time on the disp...

313 3-3. Using the Bluetooth ® audio system 3 In te ri o r a n d exte ri or fe at u res ■ Microphone

314 3-3. Using the Bluetooth ® audio system Operating the system using voice commands By following voice guidance instructions output from the speaker, voice commands enable the operation of the Bluetooth ® audio sys- tem without the need to check the display or operate . ■ Operation procedure when ...

316 3-3. Using the Bluetooth ® audio system Menu list of the Bluetooth ® audio system ■ Normal operation “BT•A Setup” can be canceled by pressing the on-hook switch or sayingthe voice command, “Cancel”. First menu Second menu Third menu Operation detail “Setup” “BT • A Setup” “Pair Audio Player” Reg...

317 3-3. Using the Bluetooth ® audio system 3 In te ri o r a n d exte ri or fe at u res ■ When using a voice command For numbers, say a combination of single digits from zero to nine. Say the command correctly and clearly. ■ Situations that the system may not recognize your voice ● When driving on r...

318 3-3. Using the Bluetooth ® audio system Operating a Bluetooth ® enabled portable player ∗ Selecting an album Press “ ∨ ” or “ ∧ ” on . Selecting tracks Turn or press “ ∧ ” or “ ∨ ” on to select the desired track. Playing and pausing tracks Press . ∗ : If equipped Fast-forwarding and reversing/Se...

319 3-3. Using the Bluetooth ® audio system 3 In te ri o r a n d exte ri or fe at u res Fast-forwarding and reversing tracks Press and hold “ ∧ ” or “ ∨ ” on . Switching the display Press . Each time is pressed, the display changes in the following order: Track title → Track title/Artist name → Trac...

320 3-3. Using the Bluetooth ® audio system Setting up a Bluetooth ® enabled portable player ∗ ∗ : If equipped Registering a portable player in the Bluetooth ® audio system allows the system to function. The following functions can be used for reg- istered portable players: ■ Functions and operation...

321 3-3. Using the Bluetooth ® audio system 3 In te ri o r a n d exte ri or fe at u res Registering a portable player Select “Pair Audio Player” using a voice command or , and per- form the procedure for registering a portable player. ( → P. 315) Selecting a portable player to be used Select “Select...

322 3-3. Using the Bluetooth ® audio system Changing the registered name of a portable player Select “Change Name” using a voice command or . Select the name of the portable player to be changed byeither of the following methods, and select “Confirm” using a voice command or : a. Press the talk swit...

323 3-3. Using the Bluetooth ® audio system 3 In te ri o r a n d exte ri or fe at u res Listing the registered portable players Select “List Audio Players” using a voice command or . The list of registered portable players will be read aloud.When listing is complete, the system returns to “BT•A Setu...

324 3-3. Using the Bluetooth ® audio system Deleting a registered portable player Select “Delete Audio Player” using a voice command or . Select the portable player to be deleted by either of the follow-ing methods and select “Confirm” using a voice command or : a. Press the talk switch and say the ...

325 3-3. Using the Bluetooth ® audio system 3 In te ri o r a n d exte ri or fe at u res Bluetooth ® audio system setup ∗ ∗ : If equipped ■ System setup items and operation procedures ● Setting voice guidance volume 1. “Setup” → 2. “System Setup” → 3. “Guidance Volume” ( → P. 352) ● Displaying the Bl...

326 3-4. Using the hands-free phone system (for cellular phone) Hands-free phone system features ∗ ∗ : If equipped This system supports Bluetooth ® , which allows you to make or receive calls without using cables to connect a cellular phone and the system, and without operating the cellular phone. O...

329 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res CAUTION ■ FCC WARNING Changes or modifications in construction not expressly approved by theparty responsible for compliance could void the user’s authority to operatethe equipment.Radio frequ...

330 3-4. Using the hands-free phone system (for cellular phone) Using the hands-free phone system ∗ ∗ : If equipped ■ Audio unit DisplayA message, name, phonenumber, etc. is displayed. Lower-case characters andspecial characters, such asan umlaut, cannot be dis-played. Displays information that isto...

331 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res ■ Steering wheel Volume The voice guidance volumecannot be adjusted using thisbutton. Off-hook switch Turns the hands-free sys-tem on/starts a call On-hook switch Turns the hands-free sys-tem ...

333 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res Operating the system by using a voice command By following voice guidance instructions output from the speaker,voice commands enable the operation of the hands-free phone sys- tem without the ...

337 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res ■ Using a short cut key First menu Second menu Operation detail “Dial XXX (name)” - Dialing a number registered in the phone book “Dial XXX (number)” - Dialing the input numbers “Phone book ad...

339 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res Making a phone call ∗ ∗ : If equipped ■ Making a phone call ● Dialing by inputting a number“Dial by number” ● Dialing by inputting a name“Dial by name” ● Speed dialing ● Dialing a number store...

341 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res When receiving a phone call ■ Answering the phone Press the off-hook switch. ■ Refusing the call Press the on-hook switch. Transferring a call A call can be transferred between the cellular ph...

342 3-4. Using the hands-free phone system (for cellular phone) Using the call history memory Follow the procedure below to use a number stored in the call historymemory: Press the talk switch and say “Redial” (when using a numberstored in the outgoing call history memory) or “Call back”(when using ...

343 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res ■ Call history Up to 5 numbers can be stored in each of the outgoing and incoming call his-tory memories. ■ When talking on the phone ● Do not talk simultaneously with the other party. ● Keep ...

344 3-4. Using the hands-free phone system (for cellular phone) Setting a cellular phone ∗ ∗ : If equipped Registering a cellular phone in the hands-free phone system allows the system to function. The following functions can be used for reg- istered cellular phones: ■ Functions and operation proced...

346 3-4. Using the hands-free phone system (for cellular phone) Changing a registered name Select “Change Name” by using a voice command or . Select the name of the cellular phone to be changed by eitherof the following methods: a. Press the talk switch and say the desired phone name, and select “Co...

347 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res Listing the registered cellular phones Selecting “List Phones” by using a voice command or causes the list of registered cellular phones to be read aloud.When listing is complete, the system r...

348 3-4. Using the hands-free phone system (for cellular phone) Changing the passkey Select “Set Passkey” by using a voice command or . Press the talk switch, say a 4 to 8-digit number, and select “Confirm” by using a voice command or . The number should be input 1 digit at a time. When the entire n...

349 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res ■ Turning on the automatic connection Select “Handsfree Power” by using a voice command or . Select “Turn on” by using a voice command or . ■ The number of cellular phones that can be register...

350 3-4. Using the hands-free phone system (for cellular phone) Security and system setup ∗ ∗ : If equipped To enter the menu of each setting, follow the steps below: ■ Security setting items and operation procedure ● Setting or changing the PIN (Personal Identification Number) 1. “Setup” → 2. “Secu...

351 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res Setting or changing the PIN ■ Setting a PIN Select “Set PIN” by using a voice command or . Enter a PIN by using a voice command or . When using , input the code 1 digit at a time. ■ Changing t...

352 3-4. Using the hands-free phone system (for cellular phone) Locking or unlocking the phone book Select “Phonebook lock” or “Phonebook unlock” by using a voice command or . Input the PIN by either of the following methods and select “Confirm” by using a voice command or : a. Press the talk switch...

355 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res Using the phone book ∗ Adding a new phone number The following methods can be used to add a new phone number: ● Inputting a phone number by using a voice command ● Transferring data from the c...

356 3-4. Using the hands-free phone system (for cellular phone) ■ Adding procedure Select “Add Entry” by using a voice command or . Use one of the following methods to input a telephone num-ber: Inputting a telephone number by using a voice command STEP2-1 Select “By Voice” by using a voice command ...

358 3-4. Using the hands-free phone system (for cellular phone) Select the name to be registered by either of the followingmethods, and select “Confirm” by using a voice command or : a. Press the talk switch and say the desired name. b. Select “Record Name” by using , and say the desired name. Selec...

359 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res Setting speed dials Select “Set Speed Dial (Speed Dial)” by using a voice com- mand or . Select the data to be registered as a speed dial by either ofthe following methods: a. Press the talk s...

361 3-4. Using the hands-free phone system (for cellular phone) 3 In te ri o r a n d exte ri or fe at u res Deleting registered data Select “Delete Entry” by using a voice command or . Select the data to be deleted by either of the following meth-ods, and select “Confirm” by using a voice command or...

362 3-4. Using the hands-free phone system (for cellular phone) Listing the registered data Selecting “List names” by using a voice command causes a list of theregistered data to be read aloud. When listing is complete, the system returns to “Phonebook”.Pressing the talk switch while the desired dat...

363 3 In te ri o r a n d exte ri or fe at u res 3-5. Using the interior lights Interior lights list ■ Illuminated entry system When the interior light switch is in the DOOR position, the interior light auto-matically turns on/off according to whether the doors are locked/unlockedand whether the door...

364 3-5. Using the interior lights Interior light DOOR position OFF ON Personal lights (Access Cab and Double Cab models) On/off Interior light and personal lights

365 3 In te ri o r a n d exte ri or fe at u res 3-6. Using the storage features List of storage features CAUTION ■ Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as thismay cause the following when cabin temperature becomes hig...

366 3-6. Using the storage features Glove box Pull up the lever. Front console box (Separated type front seat only) Push the button. CAUTION ■ Caution while driving Keep the glove box closed.Injuries may result in the event of an accident or sudden braking. CAUTION ■ Caution while driving Keep the c...

367 3-6. Using the storage features 3 In te ri o r a n d exte ri or fe at u res Cup holders Type A (Bench type front seat) Type B (Separated type front seats with an automatic transmis-sion) Type C (Separated type front seats with a manual transmission) Cup holders

368 3-6. Using the storage features ■ Removing the cup holder Type A (Bench type front seat) Type B (Separated type front seats with an automatic transmission) CAUTION ■ Items unsuitable for the cup holder Do not place anything other than cups or aluminum cans in the cup holders.Other items may be t...

369 3-6. Using the storage features 3 In te ri o r a n d exte ri or fe at u res Bottle holders Front Front console box (Separated type front seat) Rear (Double Cab models) ■ Bottle holders Depending on their size or shape, some bottles may not fit in the holders. Bottle holders

370 3-6. Using the storage features Auxiliary boxes Front Pull the lid down. Under the rear seats (Access Cab models) Pull up the lever. Raise the bottom cushion up. NOTICE ■ Items that should not be stowed in the bottle holders Put the cap on before stowing a bottle. Do not place open bottles in th...

371 3-6. Using the storage features 3 In te ri o r a n d exte ri or fe at u res Turn the knob counterclockwise. Open the lid. Press the lid against the bot-tom of the lower cushion untilit is supported by the hook-and-loop fastener. Make sure that the lid is sup-ported to prevent it from closingunex...

372 3-6. Using the storage features Overhead console (Access Cab and Double Cab models) The overhead console is useful for temporarily storing sunglassesand similar small items. Pull the lid down while pushingthe knob. CAUTION ■ Caution while driving Keep the auxiliary boxes closed and locked.Injuri...

373 3 In te ri o r a n d exte ri or fe at u res 3-7. Other interior features Sun visors Type A Forward position: Flip down. Side position: Flip down, unhook, andswing to the side. Type B Forward position: Flip down. Side position: Flip down, unhook, andswing to the side. Side extender: Place in side...

374 3-7. Other interior features Vanity mirrors Vehicles without vanity light Vehicles with vanity light Slide the cover. The light turns on when thecover is opened.

375 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Clock ■ The clock is displayed when The engine switch is in the ACC or ON position. ■ When disconnecting and reconnecting battery terminals The time display will automatically be set to 1:00. Adjusts the hours Adjusts the m...

376 3-7. Other interior features Outside temperature display (vehicles with auto anti-glare inside rear view mirror) The temperature display shows temperatures within the ranges of -40°F (-40°C) and 122°F (50°C). ■ Outside temperature display Type A Type B ■ Ice advisory indicator If the outside tem...

378 3-7. Other interior features ■ Changing display units Type A: Press and hold to display “Custom Settings Menu”. Type B: Press to display “Custom Settings Menu”. Type A: Press and select “Outside Temperature”,then press and hold . Type B: Press and select “Outside Temperature”,then press . Type A...

379 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Setting the ice advisory indicator The ice advisory indicator on the inside rear view mirror can beturned on/off. Type A: Press and hold to display “Custom Settings Menu”. Type B: Press to display “Custom Settings Menu”. Ty...

380 3-7. Other interior features ■ The outside temperature is displayed when The engine switch is in the ON position. ■ Display In the following situations, the correct outside temperature may not be dis-played, or the display may take longer than normal to change: ● When the vehicle is stopped, or ...

381 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Power outlets (12V DC) ■ The power outlets can be used when The engine switch is in the ACC or ON position. NOTICE ■ To avoid damaging the power outlets Close the power outlets lid when not in use.Foreign objects or liquids...

382 3-7. Other interior features Power outlet (120V AC) ∗ Maximum available capacity of the power outlet ■ While the vehicle is being driven The maximum capacity of the power outlet is always 120V AC/100W. ■ When the vehicle is stationary The maximum capacity of the power outlet varies depending ont...

383 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res • The shift lever is in N and the clutch pedal is not depressed. (manual transmission) A maximum capacity of 400W can only be restored by turningthe power outlet main switch off and then on again under condi-tion described ...

385 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res CAUTION ■ Using a power outlet Observe the following precautions to reduce the risk of injury. ● Use of the power outlet when it is wet with rain, drinking water or snowmay result in electrical shocks and is extremely dange...

386 3-7. Other interior features NOTICE ■ To avoid damaging the power outlet and the plug ● Close the power outlet lid when not in use. ● Foreign objects or liquids that enter the power outlet may cause a shortcircuit. ● Do not use plug adaptors to connect too many plugs to the power outlet. ● After...

387 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res NOTICE ■ If any electrical appliances are to be used while driving Securely fasten both the appliances and their cables to prevent them fromfalling or getting caught any of the power train components. ■ If the power outlet ...

388 3-7. Other interior features Seatback table ∗ ∗ : If equipped CAUTION ■ Caution while driving Observe the following precautions to avoid death or serious injury. ● Do not set up the seatback table. ● Do not sit on or place anything on the seatback table. NOTICE ■ To prevent damage to the seatbac...

389 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Insert the retaining hooks(clips) into the floor mat eye-lets. T...

390 3-7. Other interior features CAUTION Observe the following precautions.Failure to do so may cause the driver’s floor mat to slip, possibly interferingwith the pedals while driving. An unexpectedly high speed may result or it maybecome difficult to stop the vehicle, leading to a serious accident....

391 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Luggage compartment features Behind the rear seat (Double Cab models only) Cargo net hooks (vehicles with sub woofer) Grocery bag hooks Flashlight holder Storage boxes Deck Auxiliary boxes Tie-down cleats Deck hooks

392 3-7. Other interior features Auxiliary boxes Left side Turn the knob counterclock-wise. Open the lid. Right side (vehicles without 120V power outlet) Turn the knob counterclock-wise. Open the lid. Right side (vehicles with 120V power outlet) Turn the knob counterclock-wise. Open the lid.

393 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Deck hooks Deck hooks are provided forsecuring loose items. CAUTION ■ Caution while driving Keep the auxiliary boxes closed and locked.Injuries may result in the event of an accident or sudden braking. CAUTION ■ When not in...

394 3-7. Other interior features Tie-down cleats The deck rail system enables you to insert and move tie-down cleatsto their best location along deck rails to secure a load. Locking plate Thumb wheel Tie-down cleat ■ Installing the tie-down cleat Loosen the thumb wheel in acounterclockwise motion, a...

396 3-7. Other interior features Storage boxes (Double Cab models only) Storage box is designed to place things like bottles. Right side (vehicles without sub woofer) CAUTION ■ Tie-down cleat precautions ● Properly install and tighten the tie-down cleats into the deck rail system.Failure to properly...

397 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Left side Flashlight holder (Double Cab models only) Flashlight holder is designed tohold the flashlight securely. ■ Removing the separator Remove the separator.It can be installed in various positions asrequired.

398 3-7. Other interior features Grocery bag hooks (Double Cab models only) Grocery bag hook is designed tohang things like grocery bag. ■ Removing the flashlight holder Remove the flashlight holder.It can be installed in various positions asrequired. NOTICE ■ Grocery bag hook weight capacity Do not...

399 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Cargo net hooks (Double Cab models with sub woofer) Cargo net hooks are designed tohang the factory-supplied cargonet. NOTICE ■ To prevent damage to the cargo net hook Do not hang items other than the cargo net.

400 3-7. Other interior features Garage door opener ∗ The garage door opener (HomeLink ® Universal Transceiver) is manufac- tured under license from HomeLink ® . Training the HomeLink ® (for U.S. owners) The HomeLink ® compatible transceiver in your vehicle has 3 buttons which can be trained to oper...

401 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res ■ Training the HomeLink ® Point the remote control trans-mitter for the device 1 to 3 in. (25to 75 mm) from the HomeLink ® control buttons. Keep the indicator on theHomeLink ® in view while training. Press and hold down one...

403 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res ■ Training a Rolling Code system (for U.S. owners) If your device is Rolling Code equipped, follow the steps under theheading “Training the HomeLink ® ” before proceeding with the steps listed below. Locate the learn button...

404 3-7. Other interior features ■ Training an entry gate (for U.S. owners)/Training a device inthe Canadian market Place the remote control transmitter 1 to 3 in. (25 to 75 mm)away from the HomeLink ® buttons Keep the HomeLink ® indicator light in view while training. Press and hold the selected Ho...

405 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Operating HomeLink ® Press the appropriate HomeLink ® button. The HomeLink ® indicator light should come on. The HomeLink ® compatible transceiver in your vehicle continues to send a signal for up to 20 seconds as long as t...

406 3-7. Other interior features ■ Before training ● Install a new battery in the remote control transmitter. ● The battery side of the remote control transmitter must be pointed awayfrom the HomeLink ® button. ■ Certification for the garage door opener FCC ID: NZLGHSHL4 For vehicles sold in the U.S...

407 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res ■ If the following message is displayed This message appears when training procedures have not been performedcorrectly. Follow the instructions on the screen to complete or cancel train-ing. Pattern A Pattern B ■ When suppo...

408 3-7. Other interior features CAUTION ■ When training a garage door or other remote control devices The garage door or other devices may operate, so ensure people andobjects are out of danger to prevent potential harm. ■ Conforming to federal safety standards Do not use the HomeLink ® compatible ...

409 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Compass (vehicles with auto anti-glare inside rear view mirror) The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Location Type A Type B

410 3-7. Other interior features ■ Displays and directions Display Direction N North NE Northeast E East SE Southeast S South SW Southwest W West NW Northwest

411 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Calibrating the compass The direction display deviates from the true direction determined bythe earth’s magnetic field. The amount of deviation varies dependingon the geographic position of the vehicle. If you cross over on...

412 3-7. Other interior features Type A: Press and select “Compass”, then pressand hold . Type B: Press and select “Compass”, then press . Type A: Press and select “Compass Display”. Type B: Press and select “Compass Display”. Type A: Press and hold and select display on/off. Type B: Press and selec...

414 3-7. Other interior features Circling calibration If “C” appears on the display, circling calibration needs to be per-formed. Stop the vehicle in a place where it is safe to drive in a circle. Type A: Press and hold to display “Custom Settings Menu”. Type B: Press to display “Custom Settings Men...

415 3-7. Other interior features 3 In te ri o r a n d exte ri or fe at u res Drive the vehicle at 5 mph (8km/h) or less in a circle until adirection is displayed. If there is not enough space todrive in a circle, drive around theblock until a direction is dis-played. To leave the “Compass Settings M...

416 3-7. Other interior features CAUTION ■ While driving the vehicle Do not adjust the display. Adjust the display only when the vehicle isstopped. ■ When doing the circling calibration Secure a wide space, and watch out for people and vehicles in the vicinity.Do not violate any local traffic rules ...

418 4-1. Maintenance and care Cleaning and protecting the vehicle exterior ■ Automatic car washes ● Fold the mirrors and remove the detachable pole antenna before wash-ing the vehicle. Start washing from the front of the vehicle. Make sure tore-install the detachable pole antenna and extend the mirr...

419 4-1. Maintenance and care 4 Mainten ance an d ca re ■ Aluminum or chrome cladded wheels (if equipped) ● Remove any dirt immediately by using a neutral detergent. Do not usehard brushes or abrasive cleaners. Do not use strong or harsh chemicalcleaners. Use the same mild detergent and wax as used ...

420 4-1. Maintenance and care NOTICE ■ Cleaning the exterior lights ● Wash carefully. Do not use organic substances or scrub with a hard brush. This may damage the surfaces of the lights. ● Do not apply wax on the surfaces of the lights.Wax may cause damage to the lenses. ■ Detachable pole antenna i...

421 4-1. Maintenance and care 4 Mainten ance an d ca re Cleaning and protecting the vehicle interior ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a yearto maintain the quality of the vehicle’s interior. The following procedures will help protect yo...

422 4-1. Maintenance and care ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use asponge or brush to apply the foam. Rub in overlapping circles. Do not applywater. The excellent results are obtained when keeping the carpet as dry aspossible. ■ Seat belts Clean...

423 4-1. Maintenance and care 4 Mainten ance an d ca re NOTICE ■ Cleaning detergents ● Do not use organic substances such as benzene or gasoline, acidic oralkaline solutions, dye, bleach or other detergent. Doing so may discolorthe vehicle interior or cause streaks or damage to painted surfaces. ● D...

424 4-2. Maintenance Maintenance requirements ■ Repair and replacement It is recommended that genuine Toyota parts be used for repair to ensureperformance of each system. If non-Toyota parts are used in replacement orif a repair shop other than Toyota dealer performs repairs, confirm the war-ranty c...

425 4-2. Maintenance 4 Mainten ance an d ca re ■ Allow inspection and repairs to be performed by a Toyota dealer ● Toyota technicians are well-trained specialists and are kept up to datewith the latest service information. They are well informed about theoperations of all systems on your vehicle. ● ...

426 4-2. Maintenance General maintenance Engine compartment Items Check points Battery Maintenance-free. ( → P. 448) Brake fluid At the correct level? ( → P. 444) Engine coolant At the correct level? ( → P. 443) Engine oil At the correct level? ( → P. 438) Exhaust system No fumes or strange sounds? ...

427 4-2. Maintenance 4 Mainten ance an d ca re Vehicle interior Items Check points Accelerator pedal • Moves smoothly (without uneven pedal effort or catching)? Automatic transmission “Park” mechanism • Can the vehicle be hold securely on an incline with the shift lever in P? Brake pedal • Moves smo...

428 4-2. Maintenance Vehicle exterior Steering wheel • Moves smoothly?• Has correct free play?• No strange noises? Items Check points Doors • Operate smoothly? Engine hood • The lock system works properly? Fluid leaks • Is there any leakage after park- ing? Tire • Inflation pressure is correct?• Tir...

429 4-2. Maintenance 4 Mainten ance an d ca re Emission inspection and maintenance (I/M) programs Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system moni- tors the operation of the emission control system. ■ If the malfunction indica...

431 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Items Parts and tools Light bulbs ( → P. 484) • Bulb with same number and watt- age rating as original • Phillips-head screwdriver• Conventional wrench Power steering fluid level ( → P. 446) • Automatic transmission fluid DEXRON ® II or I...

432 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that maymove suddenly, become hot, or become electrically energized. To avoid deathor serious injury observe the following precautions. ■ When working on the engine compartment ● Keep hands, clothi...

433 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re NOTICE ■ If you remove the air cleaner Driving with the air cleaner removed may cause excessive engine wear dueto dirt in the air. Also a backfire could cause a fire in the engine compart-ment. ■ If the fluid level is low or high It is no...

434 4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood release lever. The hood will pop up slightly. Pull up the hood catch leverand lift the hood.

435 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re CAUTION ■ Pre-driving check Check that the hood is fully closed and locked.If the hood is not locked properly, it may open while the vehicle is in motionand cause an accident, which may result in death or serious injury. ■ After installin...

438 4-3. Do-it-yourself maintenance Engine oil Engine oil With the engine at operating temperature and turned off, check the oillevel on the dipstick. ■ Checking the engine oil Park the vehicle on level ground. After warming up the engineand turning it off, wait more than 5 minutes for the oil to dr...

439 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re 2.7 L 4-cylinder (2TR-FE) engine Low Full 4.0 L V6 (1GR-FE) engine Low Full ■ Adding engine oil 2.7 L 4-cylinder (2TR-FE) engine If the oil level is below or nearthe low level mark, add engineoil of the same type as already inthe engine.

440 4-3. Do-it-yourself maintenance 4.0 L V6 (1GR-FE) engine Make sure to check the oil type and prepare the items needed beforeadding oil. Remove the oil filler cap, turning it counterclockwise. Add engine oil slowly. Checking the dipstick. Reinstall the filler cap, turning it clockwise. The approx...

441 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Engine oil consumption ● The amount of engine oil consumed depends on the oil viscosity, thequality of the oil and the way the vehicle is driven. ● More oil is consumed under driving conditions such as high speeds andfrequent accelerati...

442 4-3. Do-it-yourself maintenance CAUTION ■ Used engine oil ● Used engine oil contains potentially harmful contaminants which maycause skin disorders such as inflammation or skin cancer, so care shouldbe taken to avoid prolonged and repeated contact. To remove used engineoil from your skin, wash t...

443 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Engine coolant The coolant level is satisfactory if it is between the FULL and LOWlines on the reservoir when the engine is cold. Reservoir cap FULL line LOW line If the level is on or below the LOW line, add coolant up to the FULL line. ...

444 4-3. Do-it-yourself maintenance Radiator and condenser Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure oftheir condition, have your vehicle checked by your Toyota dealer. Brake fluid ■ Checking fluid level Type ...

445 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Type B MAX line MIN line ■ Adding fluid Make sure to check the fluid type and prepare the necessary items. Type B only Turn the engine off. Depress the brake pedal 20 times or more. Remove the reservoir cap. Add newly opened brake fluid u...

446 4-3. Do-it-yourself maintenance Power steering fluid ■ Fluid level The fluid level should be within the appropriate range. 2.7 L 4-cylinder (2TR-FE) engine Full (when cold) Add fluid (when cold) Full (when hot) Add fluid (when hot) CAUTION ■ When filling the reservoir Take care because brake flu...

447 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Hot: Vehicle has been driven around 50 mph (80 km/h) for 20minutes, or slightly longer in frigid temperatures. (Fluidtemperature, 104°F - 175°F [40°C - 80°C]) Cold: Engine has not been run for about 5 hours. (Room tem-perature, 32°F - 104...

448 4-3. Do-it-yourself maintenance Battery ■ Battery exterior Make sure that the battery terminals are not corroded and thatthere are no loose connections, cracks, or loose clamps. Terminals Hold-down clamp CAUTION ■ Checking the fluid level Take care, as the reservoir may be hot. NOTICE ■ When add...

449 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Before recharging When recharging, the battery produces hydrogen gas which is flammableand explosive. Therefore, before recharging: ● If recharging with the battery installed on the vehicle, be sure to discon-nect the ground cable. ● Ma...

450 4-3. Do-it-yourself maintenance Washer fluid If any washer does not work, the washer tank may be empty. Open the lid. CAUTION ■ Emergency measures regarding electrolyte ● If electrolyte gets in your eyesFlush your eyes with clean water for at least 15 minutes and get immedi-ate medical attention...

451 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Add washer fluid. CAUTION ■ When refilling the washer fluid Do not refill the washer fluid when the engine is hot or running, as thewasher fluid contains alcohol and may catch fire if spilled on the engine etc. NOTICE ■ Do not use any flu...

452 4-3. Do-it-yourself maintenance Tires Replace or rotate tires in accordance with maintenance sched- ules and treadwear. ■ Checking tires New tread Treadwear indicator Worn tread The location of treadwearindicators is shown by the“TWI” or “ ” marks, etc., molded on the sidewall ofeach tire. Check...

453 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Installing tire pressure warning valves and transmitters When replacing tires or wheels, tire pressure warning valves andtransmitters must also be installed. When new tire pressure warning valves and transmitters are installed,new tire pr...

454 4-3. Do-it-yourself maintenance Press and hold the tire pressurewarning reset switch until the tirepressure warning light blinksslowly 3 times. Wait for a few minutes with the engine switch in the ON posi-tion, and then turn the engine switch to the ACC or LOCKposition. Registering ID codes The ...

455 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ When to replace your vehicle’s tires Tires should be replaced if: ● You have tire damage such as cuts, splits, cracks deep enough toexpose the fabric or bulges indicating internal damage ● A tire goes flat repeatedly or cannot be proper...

456 4-3. Do-it-yourself maintenance Access Cab models ■ Tire types 1 Summer tires Summer tires are high-speed performance tires best suited to highwaydriving under dry conditions. Since summer tires do not have the sametraction performance as snow tires, summer tires are inadequate fordriving on sno...

457 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ If you push the tire pressure warning reset switch accidentally If initialization is performed, adjust the tire inflation pressure to the speci-fied level and initialize the tire pressure warning system again. ■ When the initialization ...

458 4-3. Do-it-yourself maintenance ■ Tire pressure warning system certification FCC ID: PAXPMV107J PAXPMV108J FCC ID: HYQ13BCX For vehicles sold in U.S.A. This device complies with part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) This device may not cause harmfulin...

459 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re CAUTION ■ When inspecting or replacing tires Observe the following precautions to prevent accidents. Failure to do somay cause damage to parts of the drive train, as well as dangerous han-dling characteristics, which may lead to an accide...

460 4-3. Do-it-yourself maintenance NOTICE ■ Repairing or replacing tires, wheels, tire pressure warning valves,transmitters and tire valve caps ● When removing or fitting the wheels, tires or the tire pressure warningvalve and transmitter, contact your Toyota dealer as the tire pressurewarning valv...

461 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Tire inflation pressure ■ Tire inflation pressure The recommended cold tire inflation pressure and tire size is dis-played on the tire and loading information label. ( → P. 564) Regular Cab and Double Cab models

463 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Inspection and adjustment procedure Tire valve Tire pressure gauge Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the graduations of the gauge. If the tire inflation pres...

464 4-3. Do-it-yourself maintenance ■ Tire inflation pressure check interval You should check tire pressure every two weeks, or at least once amonth.Do not forget to check the spare. ■ Effects of incorrect tire inflation pressure Driving with incorrect tire inflation pressure may result in the follo...

465 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re CAUTION ■ Proper inflation is critical to save tire performance Keep your tires properly inflated.Otherwise, the following conditions may occur and result in an accidentcausing death or serious injury. ● Excessive wear ● Uneven wear ● Poo...

466 4-3. Do-it-yourself maintenance Wheels If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause loss of handling control. ■ Wheel selection When replacing wheels, care should be taken to ensure thatthey are equivalent to tho...

467 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ When replacing wheels The wheels of your Toyota are equipped with tire pressure warningvalves and transmitters (except for spare tire) that allow the tire pressurewarning system to provide advanced warning in the event of a loss in tire...

468 4-3. Do-it-yourself maintenance NOTICE ■ Replacing tire pressure warning valves and transmitters ● Because tire repair or replacement may affect the tire pressure warn-ing valves and transmitters, make sure to have tires serviced by yourToyota dealer or other qualified service shop. In addition,...

469 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. ■ Removal method Turn the engine switch to the LOCK position. Open the glove box. Slide off the damper. Push in each si...

470 4-3. Do-it-yourself maintenance Open the filter door. Remove the filter. ■ Replacement method Remove the air conditioningfilter and replace it with a newone. When installing the filter, followthe instructions indicated onthe label.

471 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Checking interval Inspect and replace the air conditioning filter according to the maintenanceschedule. In dusty areas or areas with heavy traffic flow, early replacementmay be required. (For scheduled maintenance information, please re...

472 4-3. Do-it-yourself maintenance Wireless remote control battery ∗ ∗ : If equipped Replace the battery with a new one if it is discharged. ■ You will need the following items: Lithium battery CR2032 ■ Replacing the battery Remove the cover using acoin protected with tape etc. Remove the discharge...

473 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ If the wireless remote control battery is discharged The following symptoms may occur. ● The wireless remote control will not function properly. ● The operational range is reduced. ■ Use a CR2032 lithium battery ● Batteries can be purch...

474 4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Turn the engine switch to the LOCK position. The fuses are located in the following places. To check ...

475 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re After a system failure, see “Fuse layout and amperageratings” ( → P. 477) for details about which fuse to check. Remove the fuse with the pull-out tool. Check if the fuse has blown. Type A Normal fuse Blown fuse Replace it with one of ana...

477 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Fuse layout and amperage ratings ■ Engine compartment Type A Type B

481 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Under the instrument panel Fuse Ampere Circuit 1 IGN 15 A Multiport fuel injection system/sequential multiport fuel injection system, anti-lock brake system, traction control system, vehicle sta-bility control system, SRS airbag system,...

483 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ After a fuse is replaced ● If the lights do not turn on even after the fuse has been replaced, a bulbmay need replacement. ( → P. 484) ● If the replaced fuse blows again, have the vehicle inspected by yourToyota dealer. ■ If there is an...

484 4-3. Do-it-yourself maintenance Light bulbs You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs...

485 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Replacing light bulbs ■ Headlights Unplug the connector. ■ Rear bulb locations High mounted stoplight Rear turn signal lights License plate lights Back-up lights Stop/tail and rear side marker lights (bulb type only)

486 4-3. Do-it-yourself maintenance Remove the rubber cover. Release the bulb retainingspring. Remove the bulb. To install a new bulb, align thetabs of the bulb with the cutoutsof the mounting hole.

487 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Front fog lights (if equipped) Unplug the connector while pull-ing the lock release. Turn the bulb counterclockwise.

488 4-3. Do-it-yourself maintenance ■ Front side marker lights Turn the bulb base counterclock-wise. Remove the light bulb.

491 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ High mounted stoplight Remove the screws and cover. Remove the light bulbs.

492 4-3. Do-it-yourself maintenance ■ License plate lights Remove the screw and light unit. Turn the bulb base counterclock-wise. Remove the light bulb.

493 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Lights other than the above If any of the lights listed below has burnt out, have it replaced byyour Toyota dealer. • Side turn signal lights (if equipped)• Stop/tail lights (LED type)• Rear side marker lights (LED type) ■ Condensation ...

496 5-1. Essential information Emergency flashers NOTICE ■ To prevent battery discharge Do not leave the emergency flashers on longer than necessary when theengine is not running. Use the emergency flashers if the vehicle malfunctions or is involved in an accident. Press the switch to flash allthe t...

5 Wh en t ro uble ar ises 497 5-1. Essential information If your vehicle needs to be towed Before towing The following may indicate a problem with your transmission. Contactyour Toyota dealer before towing. ● The engine is running, but the vehicle will not move. ● The vehicle makes an abnormal sound...

498 5-1. Essential information Type B Towing hook ■ Emergency towing procedure The engine switch must be in the ACC (engine off) or the ON(engine running) position. 4WD models: Put the front-wheel drive control switch in H2. Put the shift lever in N. Release the parking brake. CAUTION ■ Caution whil...

5 Wh en t ro uble ar ises 499 5-1. Essential information Towing with a sling-type truck NOTICE ■ Emergency towing eyelet/hook precautions ● Before emergency towing, check that the eyelet/hook is not broken ordamaged. ● Fasten the towing cable or chain securely to the eyelet/hook. ● Do not jerk the e...

500 5-1. Essential information Towing with a wheel lift-type truck from the front Vehicles with an automatic trans-mission: Use a towing dollyunder the rear wheels. 2WD models with a manualtransmission: We recommend touse a towing dolly under the rearwheels. When not using a towing dolly,release the...

5 Wh en t ro uble ar ises 501 5-1. Essential information Towing with a wheel lift-type truck from the rear 2WD models Turn the engine switch to theACC position. 4WD models We recommend to use a towingdolly under the front wheels. When not using a towing dolly,turn the engine switch to the ACCpositio...

502 5-1. Essential information Using a flat bed truck If your Toyota is transported by aflat bed truck, it should be tieddown at the locations shown inthe illustration. If you use chains or cables to tiedown your vehicle, the anglesshaded in black must be 45 ° . Do not overly tighten the tiedowns or...

5 Wh en t ro uble ar ises 503 5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms ● Fluid leaks under the vehicle(Water dripping fr...

504 5-1. Essential information Fuel pump shut off system Follow the procedure below to restart the engine after the system isactivated. Turn the engine switch to the ACC or LOCK position. Restart the engine. NOTICE ■ Before starting the engine Inspect the ground under the vehicle.If you find that fu...

5 Wh en t ro uble ar ises 505 5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer sounds... Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous. The following warning indicates a possible problem in the brake sys-tem. Immediately stop the veh...

506 5-2. Steps to take in an emergency Stop the vehicle immediately. The following warnings indicate the possibility of damage to the vehi-cle that may lead to an accident. Immediately stop the vehicle in asafe place and contact your Toyota dealer. *: The light may come on when the oil level is extr...

508 5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem,check that the warning light turns off. Warning light Warning light/Details Correction procedure Open door warning light Indicates that a door is not fully close...

5 Wh en t ro uble ar ises 509 5-2. Steps to take in an emergency Tire pressure warning light When the light comes on: Low tire inflation pressure such as• Natural causes ( → P. 510) • Flat tire ( → P. 515) Adjust the tire inflation pressure to the speci-fied level. The light will turn off after a fe...

510 5-2. Steps to take in an emergency * : Driver’s and front passenger’s seat belt buzzer: The driver’s and front passenger’s seat belt buzzer sounds to alert the driverand front passenger that their seat belt is not fastened. Once the engineswitch is turned to the ON or START position, the buzzer ...

5 Wh en t ro uble ar ises 511 5-2. Steps to take in an emergency ■ When a tire is replaced with a spare tire The temporary spare tire is not equipped with the tire pressure warningvalve and transmitter. If a tire goes flat, the tire pressure warning light willnot turn off even though the flat tire i...

512 5-2. Steps to take in an emergency ■ After changing the engine oil (U.S.A. only) Make sure to reset the oil maintenance data. ( → P. 441) ■ Customization that can be configured at Toyota dealer The vehicle speed linked seat belt reminder buzzer can be disabled.(Customizable features → P. 583) CA...

514 5-2. Steps to take in an emergency NOTICE ■ Precaution when installing a different tire When a tire of a different specification or maker is installed, the tire pres-sure warning system may not operate properly.

5 Wh en t ro uble ar ises 515 5-2. Steps to take in an emergency If you have a flat tire Remove the flat tire and replace it with the spare provided. ■ Before jacking up the vehicle ● Stop the vehicle on a hard, flat surface. ● Set the parking brake. ● Shift the shift lever to P (automatic transmiss...

516 5-2. Steps to take in an emergency Taking out the jack and tool bag Regular Cab models with bench type seat Pull the lever and fold down theseatback. Access Cab models Double Cab models Tool bag Jack Tool bag Jack

520 5-2. Steps to take in an emergency Loosen and remove the jack. Loosen Tighten Assemble the jack handle (in the tool bag) Assemble the jack handle exten-sion as shown. Taking out the spare tire Insert the end of the jack handleextension into the loweringscrew and turn it counterclock-wise.

5 Wh en t ro uble ar ises 521 5-2. Steps to take in an emergency After the tire is lowered com-pletely to the ground, remove theholding bracket. Replacing a flat tire Chock the tires. Flat tire Wheel chock positions Front Left-hand side Behind the rear right-hand side tire Right-hand side Behind the...

524 5-2. Steps to take in an emergency Remove all the wheel nuts andthe tire. When resting the tire on theground, place the tire so that thewheel design faces up to avoidscratching the wheel surface. Installing the tire Remove any dirt or foreign mat-ter from the wheel contact sur-face. If foreign m...

526 5-2. Steps to take in an emergency Firmly tighten each nut two or three times in the order shownin the illustration. Tightening torque: 83 ft·lbf (113 N·m, 11.5 kgf·m) 2WD models except PreRunner 4WD models and PreRunner Stowing the flat tire, jack and all tools Lay down the tire with the outers...

5 Wh en t ro uble ar ises 527 5-2. Steps to take in an emergency 4WD models only: Fasten theclaws of the holding bracket intothe wheel holes as shown in theillustration. Holding bracket Claw Then secure the tire, taking care that the tire goes straight upwithout catching on any other part, to preven...

528 5-2. Steps to take in an emergency CAUTION ■ Using the jack Improper use of the jack may lead to death or serious injuries due to thevehicle suddenly falling off the jack. ● Do not use the jack for any purpose other than replacing tires or install-ing and removing tire chains. ● Only use the jac...

530 5-2. Steps to take in an emergency CAUTION ■ Speed limit when using the temporary spare tire Do not drive at speeds in excess of 50 mph (80 km/h) when a temporaryspare tire is installed on the vehicle. The temporary spare tire is not designed for driving at high speeds. Fail-ing to observe this ...

5 Wh en t ro uble ar ises 531 5-2. Steps to take in an emergency NOTICE ■ Do not drive the vehicle with a flat tire Do not continue driving with a flat tire.Driving even a short distance with a flat tire can damage the tire and thewheel beyond repair. ■ When stowing the flat tire Ensure that there i...

532 5-2. Steps to take in an emergency If the engine will not start If the engine still does not start after following the correct starting procedure ( → P. 143) or releasing the steering lock ( → P. 144), confirm the following points. ■ The engine will not start even when the starter motor oper-ate...

5 Wh en t ro uble ar ises 533 5-2. Steps to take in an emergency If the shift lever cannot be shifted from P (vehicles with an automatic transmission) If the shift lever cannot be shifted with your foot on the brake, there may be a problem with the shift lock system (a system to prevent accidental o...

534 5-2. Steps to take in an emergency If you lose your keys New genuine Toyota keys can be made by your Toyota dealer using the other key and the key number stamped on your key number plate.

5 Wh en t ro uble ar ises 535 5-2. Steps to take in an emergency If the vehicle battery is discharged The following procedures may be used to start the engine if the vehicle’s battery is discharged. You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) ca...

5 Wh en t ro uble ar ises 537 5-2. Steps to take in an emergency ■ Starting the engine when the battery is discharged (vehicles with anautomatic transmission) The engine cannot be started by push-starting. ■ Avoiding a discharged battery ● Turn off the headlights and the audio system while the engin...

538 5-2. Steps to take in an emergency CAUTION ■ Battery precautions The battery contains poisonous and corrosive acidic electrolyte, whilerelated parts contain lead and lead compounds. Observe the following pre-cautions when handling the battery. ● When working with the battery, always wear safety ...

5 Wh en t ro uble ar ises 539 5-2. Steps to take in an emergency If your vehicle overheats If your engine overheats: Stop the vehicle in a safe place and turn off the air condi-tioning system. Check to see if steam is coming out from under the hood. If you see steam: Stop the engine. Carefully lift ...

540 5-2. Steps to take in an emergency The engine has cooled down sufficiently. The engine coolant temperature gauge indicates C. Check the engine coolant level. Look for obvious coolant leaks from the radiator, hoses andunder the vehicle. Note that water draining from the air conditioning is normal...

5 Wh en t ro uble ar ises 541 5-2. Steps to take in an emergency ■ Overheating If you observe the following, your vehicle may be overheating. ● The engine coolant temperature gauge enters the red zone or a loss ofpower is experienced. ● Steam is coming from under the hood. CAUTION ■ To prevent an ac...

542 5-2. Steps to take in an emergency If the vehicle becomes stuck CAUTION ■ When attempting to free a stuck vehicle If you choose to rock the vehicle back and forth to free it, make sure the sur-rounding area is clear, to avoid striking other vehicles, objects or persons.The vehicle may also lunge...

5 Wh en t ro uble ar ises 543 5-2. Steps to take in an emergency NOTICE ■ To avoid damaging the transmission and other components ● Avoid spinning the wheels and do not rev the engine. ● If the vehicle remains stuck after trying these procedures, the vehicle mayrequire towing to be freed.

544 5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following pro- cedure: Steadily step on the brake pedal with both feet and firmlydepress i...

5 Wh en t ro uble ar ises 545 5-2. Steps to take in an emergency CAUTION ■ If the engine has to be turned off while driving ● Power assist for the brakes and steering wheel will be lost, making thebrake pedal harder to depress and the steering wheel heavier to turn.Decelerate as much as possible bef...

548 6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions 2WD models except PreRunner * : Unladen vehicle 4WD models and PreRunner (except Regular Cab models) * : Unladen vehicle Cab type Regular Cab Access Cab Double Cab Except X-Runner X-Runner Overall length 190.4 in. (4835 mm) ...

549 6-1. Specifications 6 Vehicl e sp ecification s * : Unladen vehicle Vehicle capacity weight 2WD models except PreRunner * : Installing accessories in addition to those installed at the factory increases vehicle weight, thereby reducing vehicle capacity weight. Contact yourToyota dealer about the...

553 6-1. Specifications 6 Vehicl e sp ecification s Vehicle identification ■ Vehicle identification number The vehicle identification number (VIN) is the legal identifier for yourvehicle. This is the primary identification number for your Toyota. It isused in registering the ownership of your vehicl...

554 6-1. Specifications ■ Engine number The engine number is stamped on the engine block as shown. 2.7 L 4-cylinder (2TR-FE) engine 4.0 L V6 (1GR-FE) engine

555 6-1. Specifications 6 Vehicl e sp ecification s Engine 2.7 L 4-cylinder (2TR-FE) engine 4.0 L V6 (1GR-FE) engine Fuel Model 2TR-FE Type 4-cylinder in line, 4-cycle, gasoline Bore and stroke 3.74 × 3.74 in. (95.0 × 95.0 mm) Displacement 164.3 cu.in. (2694 cm 3 ) Drive belt tension Automatic adjus...

556 6-1. Specifications Lubrication system * : The engine oil capacity is a reference quantity to be used when exchanging. Warm up and turn off the engine, wait more than 5 minutes, and check the oillevel on the dipstick. Oil capacity(Drain and refill - reference * ) Without filter With filter 2.7 L...

557 6-1. Specifications 6 Vehicl e sp ecification s ■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. UseToyota approved “Toyota Genuine Motor Oil” or equivalent to satisfythe following grade and viscosity. Oil grade: ILSAC multigrade engine oil Recommended viscosity:...

558 6-1. Specifications 4.0 L V6 (1GR-FE) engineSAE 5W-30 SAE 5W-30 is the best choice forgood fuel economy and goodstarting in cold weather. If SAE 5W-30 is not available,SAE 10W-30 oil may be used.However, it should be replacedwith SAE 5W-30 at the next oilchange. Oil viscosity (5W-30 is explained...

559 6-1. Specifications 6 Vehicl e sp ecification s Cooling system Ignition system Capacity 2.7 L 4-cylinder (2TR-FE) engine 4.0 L V6 (1GR-FE) engine Vehicles with an automatic transmission9.1 qt. (8.6 L, 7.6 Imp.qt.)Vehicles with a manual transmission9.2 qt. (8.7 L, 7.7 Imp.qt.)Vehicles with an aut...

563 6-1. Specifications 6 Vehicl e sp ecification s Brakes * 1 : Minimum pedal clearance when depressed with a force of 110 lbf (490 N, 50 kgf) with the engine running. * 2 : Parking brake pedal travel when depressed with a force of 67.4 lbf (300 N, 30.6 kgf). * 3 : Parking brake lever travel when p...

564 6-1. Specifications Steering Tires and wheels Type A * : If you affix the spare tire to a front position, please make sure to adjust the tire to the correct inflation pressure as soon as possible. Free play Less than 1.2 in. (30 mm) Power steering fluid type Automatic transmission fluid DEXRON ®...

567 6-1. Specifications 6 Vehicl e sp ecification s Type F Tire size P265/60R18 109H Tire inflation pressure(Recommended cold tire inflation pressure) Front tires:29 psi (200 kPa, 2.0 kgf/cm 2 or bar) Rear tires:29 psi (200 kPa, 2.0 kgf/cm 2 or bar) Spare tire:29 psi (200 kPa, 2.0 kgf/cm 2 or bar) D...

569 6-1. Specifications 6 Vehicl e sp ecification s Fuel information ■ Fuel tank opening for unleaded gasoline To help prevent incorrect fueling, your Toyota has a fuel tank opening thatonly accommodates the special nozzle on unleaded fuel pumps. ■ If your engine knocks ● Consult your Toyota dealer....

571 6-1. Specifications 6 Vehicl e sp ecification s ■ Toyota does not recommend gasoline containing MMT Some gasoline contains octane enhancing additive called MMT(Methylcyclopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuelcontaining MMT is...

572 6-1. Specifications Tire information Typical tire symbols Tire size ( → P. 574) DOT and Tire Identification Number (TIN) ( → P. 573) Location of treadwear indicators ( → P. 452) Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are thestrands which form t...

573 6-1. Specifications 6 Vehicl e sp ecification s Typical DOT and tire identification number (TIN) DOT symbol * Tire Identification Number(TIN) Tire manufacturer’sidentification mark Tire size code Manufacturer’s optional tiretype code (3 or 4 letters) Manufacturing week Manufacturing year * :The ...

574 6-1. Specifications Tire size ■ Typical tire size information The illustration indicates typicaltire size. Tire use(P = Passenger car,T = Temporary use) Section width (millimeters) Aspect ratio(tire height to section width) Tire construction code(R = Radial, D = Diagonal) Wheel diameter (inches)...

575 6-1. Specifications 6 Vehicl e sp ecification s Tire section names Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer Uniform Tire Quality Grading This information has been prepared in accordance with regulationsissued by the National Highway Tra...

576 6-1. Specifications ■ Treadwear The treadwear grade is a comparative rating based on the wearrate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2)times as well on the government course as ...

577 6-1. Specifications 6 Vehicl e sp ecification s Warning: The temperature grades for this tire are established for atire that is properly inflated and not overloaded.Excessive speed, underinflation, or excessive loading, eitherseparately or in combination, can cause heat buildup and possibletire ...

583 6 Vehicl e sp ecification s 6-2. Customization Customizable features Customizing inside rear view mirror features (vehicles with autoanti-glare inside rear view mirror) For information displayed on the inside rear view mirror, it is possibleto change the units displayed for outside temperature, ...

585 6-2. Customization 6 Vehicl e sp ecification s Type A: Each time is pressed and held, the display col- ors change in the following order: “Green” → “White” → “Orange” → “Blue” Type B: Each time is pressed, the display colors change in the following order: “Green” → “White” → “Orange” → “Blue” To...

587 6-2. Customization 6 Vehicl e sp ecification s Items to initialize Item When to initialize Reference Engine oil maintenance data After changing engine oil P. 441 Tire pressure warning sys-tem • When rotating the tires on vehi- cles differing with front and rear tire inflation pressures. • When c...

591 7 For owners Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions inEnglish.

593 7 For owners SRS airbag instructions for Canadian owners (in French) The following is a French explanation of SRS airbag instructionsextracted from the SRS airbag section in this manual.See the SRS airbag section for more detailed SRS airbag instruc-tions in English.

604 Camper information Center of gravity location The figures given in the illustration indicate the recommended centerof gravity zone. Recommended location forcargo center of gravity forcargo weight rating Rear end of truck bed * : Truck-campers cannot be used with the X-Runner since it is not desi...

605 7 For owners Cargo weight rating and proper matching When the truck is used to carry a slide-in camper, the total cargo loadof the truck consists of the manufacturer’s camper weight figure, theweight of installed additional camper equipment not included in themanufacturer’s camper weight figure,...

606 Access Cab models 2 people, 2TR-FE engine, 2WD except PreRunner: 750 lb. (340 kg) 4 people, 2TR-FE engine, 2WD except PreRunner: 450 lb. (204 kg) 2 people, 2TR-FE engine, PreRunner: 1000 lb. (453 kg) 4 people, 2TR-FE engine, PreRunner: 700 lb. (317 kg) 2 people, 1GR-FE engine, PreRunner: 950 lb....

607 7 For owners Gross axle and vehicle weight ratings Secure loose items to prevent weight shifts that could affect the bal-ance of your vehicle. When the truck camper is loaded, drive to ascale and weigh on the front and on the rear wheels separately todetermine axle loads. Individual axle loads s...

609 7 For owners PreRunner 4WD models Cab type GVWR Access Cab Vehicles with 2.7 L 4-cylinder (2TR-FE) engine5250 lb. (2380 kg)Vehicles with 4.0 L V6 (1GR-FE) engine5400 lb. (2445 kg) Double Cab Cab type GVWR Regular Cab 5100 lb. (2310 kg) Access Cab Vehicles with 2.7 L 4-cylinder (2TR-FE) engine535...

614 Alphabetical index Alphabetical index A/C ............................................. 248ABS ........................................... 200Access doors ............................. 43Active traction control system .................................... 190 Air conditioning filter.................

628 GAS STATION INFORMATION Auxiliary catch lever P. 434 Fuel filler door P. 81 Tire inflation pressure P. 564 Hood lock release lever P. 434 Fuel tank capacity(Reference) 21.1 gal. (80.0 L, 17.6 Imp.gal.) Fuel type Unleaded gasoline, Octane Rating 87 (Research Octane Number 91) or higher Cold tire ...