Toyota 2012 Avalon- Manuals

25 Symbols used throughout this manual Cautions & Notices CAUTION This is a warning against anything which may cause injury to people if thewarning is ignored. You are informed about what you must or must not do inorder to reduce the risk of injury to yourself and others. NOTICE This is a warnin...

TABLE OF CONTENTS 1 1 Before driving Adjusting and operating features such as door locks, mirrors, and steering column. 2 When driving Driving, stopping and safe-driving information. 3 Interior features Air conditioning and audio systems, as well as other interior features for a comfortable driving ...

28 1-1. Key information Keys Using the mechanical key (vehicles with smart key system) Take out the mechanical key. After using the mechanical key,store it in the electronic key. Carrythe mechanical key together withthe electronic key. If the electronickey battery is depleted or thesmart key system ...

29 1-1. Key information 1 Before driving ■ When required to leave a key to the vehicle with a parking attendant(Vehicles with smart key system) Lock the glove box as circumstances demand. ( → P. 350) Remove the mechanical key for your own use and provide the attendant withthe electronic key only. ■ ...

30 1-2. Opening, closing and locking the doors and trunk Smart key system ∗ ∗ : If equipped The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.) Locks and unlocks the doors ( →...

31 1-2. Opening, closing and locking the doors and trunk 1 Before driving Unlocking and locking the doors Grip the driver’s door handle tounlock the door. Grip the passen-ger’s door handle to unlock allthe doors. * Make sure to touch the sensor onthe back of the handle. The door cannot be unlocked f...

32 1-2. Opening, closing and locking the doors and trunk Antenna location and effective range ■ Antenna location Antennas outside cabin Antenna outside trunk Antenna inside trunk Antennas inside cabin

33 1-2. Opening, closing and locking the doors and trunk 1 Before driving ■ Effective range (areas within which the electronic key isdetected) When locking or unlockingthe doors The system can be operatedwhen the electronic key iswithin about 3 ft. (1 m) of anoutside door handles. (Onlythe doors det...

34 1-2. Opening, closing and locking the doors and trunk ■ Operation signals A buzzer sounds and the emergency flashers flash to indicate that the doorshave been locked/unlocked. (Locked: Once; Unlocked: Twice) ■ Conditions affecting operation The smart key system uses weak radio waves. In the follo...

35 1-2. Opening, closing and locking the doors and trunk 1 Before driving ■ Switching the door unlock function It is possible to set which doors the entry function unlocks. Turn the “ENGINE START STOP” switch off. When the indicator on the key surface is turned off, push and hold , , or for approxim...

36 1-2. Opening, closing and locking the doors and trunk ■ Battery-saving function In the following circumstances, the entry function is disabled in order to pre-vent the vehicle and electronic key batteries from discharging. ● When the entry function has not been used for 2 weeks or more ● When the...

37 1-2. Opening, closing and locking the doors and trunk 1 Before driving ■ Note for the smart key system ● Even when the electronic key is within the effective range (detectionareas), the system may not operate properly in the following cases. • The electronic key is too close to the window or outs...

38 1-2. Opening, closing and locking the doors and trunk ■ Security feature If a door is not opened within approximately 60 seconds after the vehicle isunlocked, the theft deterrent system automatically locks the vehicle again. ■ Alarms and warning indicators A combination of exterior and interior a...

39 1-2. Opening, closing and locking the doors and trunk 1 Before driving ■ If the smart key system does not operate properly ● Locking and unlocking the doors: Use the mechanical key. ( → P. 505) ● Starting the engine: → P. 506 ■ When the electronic key battery is fully depleted → P. 440 Alarm Situ...

41 1-2. Opening, closing and locking the doors and trunk 1 Before driving CAUTION ■ Caution regarding interference with electronic devices ● People with implanted pacemakers or cardiac defibrillators should keepaway from the smart key system antennas. ( → P. 32) The radio waves may affect the operat...

42 1-2. Opening, closing and locking the doors and trunk Wireless remote control The wireless remote control can be used to lock and unlock the vehi- cle and the trunk from outside the vehicle. Vehicles with smart key system Locks all doors Unlocks all doors Pressing the button unlocksthe driver’s d...

43 1-2. Opening, closing and locking the doors and trunk 1 Before driving ■ Operation indicator Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked:Twice) Trunk: A buzzer sounds to indicate that the trunk has been unlo...

45 1-2. Opening, closing and locking the doors and trunk 1 Before driving ■ Certification for wireless remote control For vehicles sold in the U.S.A. FCC ID: HYQ14AABFCC ID: HYQ13BZHFCC ID: HYQ14ABKFCC ID: HYQ13BZWFCC ID: HYQ14AEMFCC ID: NI4TMLF-1 NOTE:This device complies with part 15 of the FCC Ru...

47 1 1-2. Opening, closing and locking the doors and trunk Before driving Doors The vehicle can be locked and unlocked using the entry function, wireless remote control or door lock switch. ■ Entry system (vehicles with smart key system) → P. 31 ■ Wireless remote control → P. 42 ■ Key Vehicles with ...

48 1-2. Opening, closing and locking the doors and trunk ■ Door lock switch Locks all doors Unlocks all doors ■ Inside lock button Locks the door Unlocks the door The front doors can be openedby pulling the inside handleseven if the lock buttons are inthe lock position.

49 1-2. Opening, closing and locking the doors and trunk 1 Before driving Locking the front doors from the outside without a key Move the inside lock button to the lock position. Close the door. Vehicles with smart key system The door cannot be locked if the “ENGINE START STOP” switch isin the ACCES...

50 1-2. Opening, closing and locking the doors and trunk Automatic door locking and unlocking systems The following functions can be set or canceled: Function Operation Shift position linked door locking function Shifting the shift lever out of “P” locks all doors. Shift position linked door unlocki...

51 1-2. Opening, closing and locking the doors and trunk 1 Before driving ■ Setting and canceling the functions To switch between setting and canceling, follow the procedurebelow: Vehicles with smart key system: Close all the doors and turnthe “ENGINE START STOP” switch to IGNITION ON mode.(Perform ...

53 1-2. Opening, closing and locking the doors and trunk 1 Before driving ■ Customization that can be configured at Toyota dealer Settings (e.g. unlocking function using a key) can be changed. (Customizable features → P. 545) CAUTION ■ To prevent an accident Observe the following precautions while d...

54 1-2. Opening, closing and locking the doors and trunk Trunk The trunk can be opened using the trunk opener, smart key system or wireless remote control. ■ Opening the trunk from inside the vehicle Push the opener switch. ■ Opening the trunk from outside the vehicle Entry system (vehicles with sma...

55 1-2. Opening, closing and locking the doors and trunk 1 Before driving ■ Internal trunk release lever ■ In case the trunk opener is not actuated The trunk lid can be opened by pullingdown on the glow-in-the-dark leverlocated on the inside of trunk lid. The lever will continue to glow for sometime...

56 1-2. Opening, closing and locking the doors and trunk CAUTION ■ Caution while driving ● Keep the trunk lid closed while driving.If the trunk lid is left open, it may hit near-by objects while driving or lug-gage in the trunk may be unexpectedly thrown out, causing an accident.In addition, exhaust...

57 1-2. Opening, closing and locking the doors and trunk 1 Before driving CAUTION ■ When children are in the vehicle Observe the following precautions.Failure to do so may result in death or serious injury. ● Do not allow children to enter the trunk.If a child is accidentally locked in the trunk, th...

59 1 Before driving 1-3. Adjustable components (seats, steering wheel, mirrors) Front seats Active head restraint When a front seatback receivesa strong impact during a rear-end collision, the head restraintmoves slightly forward andupward to provide support for theoccupants head. Seat leg support s...

60 1-3. Adjustable components (seats, steering wheel, mirrors) ■ Active head restraint Even small forces applied to the seatback may cause the head restraint tomove. Pushing up a locked head restraint forcibly may cause the headrestraint inner structure to appear. This does not indicate a problem. C...

61 1 1-3. Adjustable components (seats, steering wheel, mirrors) Before driving Rear seats ■ Keep the flap area clear To adjust the seat back angle, pull the lock release lever. Do not place objects on the flap area. Ifobjects are left in the gap, the recliningseatback will not lock properly, and ma...

63 1 1-3. Adjustable components (seats, steering wheel, mirrors) Before driving Driving position memory system ∗ ∗ : If equipped Your preferred driving position (the position of the driver’s seat and outside rear view mirrors) can be entered into the computer’s mem- ory and recalled with the touch o...

64 1-3. Adjustable components (seats, steering wheel, mirrors) ■ Recalling the memorized position Vehicles with smart key system: Turn the “ENGINE STARTSTOP” switch to IGNITION ON mode. Vehicles without smart key system: Turn the engine switchto the “ON” position. Push button “1” or “2” to recallthe...

65 1-3. Adjustable components (seats, steering wheel, mirrors) 1 Before driving Linking driving position memory with door unlock operation(vehicles with smart key system) Memorized driving positions can be recalled when you unlock thedriver’s door using the entry function or wireless remote control ...

66 1-3. Adjustable components (seats, steering wheel, mirrors) ■ Canceling the linked door unlock operation Close the driver’s door with the “ENGINE START STOP”switch OFF. Push the “SET” button and the button on the wireless remote control at the same time for about 1 second until youhear 2 beeps. ■...

67 1 1-3. Adjustable components (seats, steering wheel, mirrors) Before driving Head restraints Head restraints are provided for all seats. Front seats Up Down Push and hold the lock releasebutton when lowering the headrestraint. Rear seats Up Down Push and hold the lock releasebutton when lowering ...

69 1-3. Adjustable components (seats, steering wheel, mirrors) 1 Before driving CAUTION ■ Head restraint precautions Observe the following precautions regarding the head restraints. Failure todo so may result in death or serious injury. ● Use the head restraints designed for each respective seat. ● ...

70 1-3. Adjustable components (seats, steering wheel, mirrors) Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts Extend the shoulder belt sothat it comes fully over theshoulder, but does notcome into contact with thenec...

71 1-3. Adjustable components (seats, steering wheel, mirrors) 1 Before driving Seat belt comfort guide (outside rear seats) If the shoulder belt sits close to a person’s neck, use the seat beltcomfort guide. Pull the comfort guide from thepocket. Slide the belt past the slot of theguide. The elasti...

73 1-3. Adjustable components (seats, steering wheel, mirrors) 1 Before driving ■ Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may alsolock if you lean forward too quickly. A slow, easy motion will allow the belt toextend, and you can move ...

74 1-3. Adjustable components (seats, steering wheel, mirrors) ■ People suffering illness Obtain medical advice and wear the seat belt in the proper way. ( → P. 70) ■ Child seat belt usage The seat belts of your vehicle were principally designed for persons of adultsize. ● Use a child restraint syst...

75 1-3. Adjustable components (seats, steering wheel, mirrors) 1 Before driving CAUTION Observe the following precautions to reduce the risk of injury in the event ofsudden braking, sudden swerving or an accident. Failing to do so may causedeath or serious injury. ■ Wearing a seat belt ● Ensure that...

76 1-3. Adjustable components (seats, steering wheel, mirrors) CAUTION ■ Seat belt pretensioners ● Do not place anything, such as a cushion, on the front passenger’s seat.Doing so will disperse the passenger’s weight, which prevents the sensorfrom detecting the passenger’s weight properly. As a resu...

77 1-3. Adjustable components (seats, steering wheel, mirrors) 1 Before driving CAUTION ■ Using a seat belt comfort guide ● Make sure the belt is not twisted and that it lies flat. The elastic cord mustbe behind the belt and the guide must be on the front. ● To reduce the chance of injury in case of...

78 1-3. Adjustable components (seats, steering wheel, mirrors) Steering wheel The steering wheel can be adjusted to a comfortable position. ■ To change the angle Hold the steering wheel, pressthe tilt lock release lever, andadjust to the ideal position bymoving the steering wheelvertically. When the...

79 1-3. Adjustable components (seats, steering wheel, mirrors) 1 Before driving CAUTION ■ After adjusting the steering wheel Make sure that the steering wheel is locked.Otherwise, the steering wheel may move suddenly, possibly causing anaccident and resulting in death or serious injury. ■ While driv...

80 1-3. Adjustable components (seats, steering wheel, mirrors) Inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions. In auto mode, sensors are used to detect the headlights of vehiclesbehind and automatically reduces the reflected light...

81 1-3. Adjustable components (seats, steering wheel, mirrors) 1 Before driving Adjusting the height of the rear view mirror Adjust the height of the rear viewmirror by moving it up and down. ■ To prevent sensor error CAUTION ■ While driving Do not adjust the position of the mirror.Doing so may lead...

82 1-3. Adjustable components (seats, steering wheel, mirrors) Outside rear view mirrors Folding the mirrors Push backward to fold the mir-rors. Mirror angle can be adjusted using the switch. Select a mirror to adjust. Left Right Adjust the mirror. Up Right Down Left STEP 1 STEP 2

83 1-3. Adjustable components (seats, steering wheel, mirrors) 1 Before driving ■ The outside rear view mirrors can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in the ACCESSORY or IGNITIONON mode. Vehicles without smart key system The engine switch is in the “AC...

84 1-3. Adjustable components (seats, steering wheel, mirrors) CAUTION ■ While driving Observe the following precautions.Failing to do so may result in losing control of the vehicle and cause an acci-dent, resulting in death or serious injury. ● Do not adjust the mirrors. ● Before driving, be sure t...

85 1 Before driving 1-4. Opening and closing the windows and moon roof Power windows Lock switch Press the switch down to lockpassenger window switches. Use this switch to prevent chil-dren from accidentally opening orclosing a passenger window. The power windows can be opened and closed using the f...

86 1-4. Opening and closing the windows and moon roof ■ The power windows can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. ■ Operating the power windows after turnin...

87 1-4. Opening and closing the windows and moon roof 1 Before driving CAUTION ■ When closing the windows Observe the following precautions. Failing to do so may result in death or serious injury. ● Check to make sure that all passengers do not have any part of their bodyin a position where it could...

88 1-4. Opening and closing the windows and moon roof Moon roof ∗ ∗ : If equipped Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Opening and closing Open Stops just before it is openedfully. Press the switch again tofully open. Close To stop partway, press theswitch ...

89 1-4. Opening and closing the windows and moon roof 1 Before driving ■ The moon roof can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. ■ Operating the moon roof aft...

90 1-4. Opening and closing the windows and moon roof ■ To reduce moon roof wind noise When the moon roof is opened automatically, it will stop slightly before thefully open position. Driving with the moon roof in this position can helpreduce wind noise. ■ Sunshade The sunshade can be opened and clo...

91 1-4. Opening and closing the windows and moon roof 1 Before driving CAUTION ■ When opening the moon roof Observe the following precautions.Failing to do so may cause death or serious injury. ● Do not allow any passengers to put their hands or heads outside the vehi-cle while it is moving. ● Do no...

92 1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle Turn the “ENGINE START STOP” switch or the engine switchOFF and ensure that all the doors and windows are closed. ■ Opening the fuel tank cap Press the fuel filler doorop...

93 1-5. Refueling 1 Before driving Closing the fuel tank cap After refueling, turn the fuel tankcap clockwise until you hear aclick. The cap will revolve slightlyin the opposite direction oncereleased. ■ Fuel types Use unleaded gasoline. (Octane Rating 87 [Research Octane Number 91] orhigher) ■ Fuel...

94 1-5. Refueling CAUTION ■ When refueling the vehicle Observe the following precautions while refueling the vehicle. Failure to doso, may result in death or serious injury. ● Before opening the fuel door, touch the vehicle or some other metal sur-face to discharge any static electricity.It is impor...

95 1-5. Refueling 1 Before driving NOTICE ■ Refueling Do not spill fuel during refueling. Failing to do so may damage the vehicle, such as causing the exhaust sys-tems to operate abnormally or damaging fuel system components or thevehicle’s painted surface.

96 1-6. Theft deterrent system Engine immobilizer system The vehicle’s keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. Vehi...

97 1-6. Theft deterrent system 1 Before driving ■ System maintenance The vehicle has a maintenance-free type engine immobilizer system. ■ Conditions that may cause the system to malfunction ● If the grip portion of the key is in contact with a metallic object. ● If the key is in close proximity to o...

98 1-6. Theft deterrent system ■ Certifications for the engine immobilizer system For vehicles sold in the U.S.A. FCC ID: MOZRI-21BTYFCC ID: NI4TMIMB-1 This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions: (1) this device may not cause harmful inter...

99 1 1-6. Theft deterrent system Before driving Alarm The system sounds the alarm and flashes lights when forcible entry is detected. ■ Triggering the alarm The alarm is triggered in the following situations when the alarmis set: ● A locked door or trunk is unlocked or opened in any way otherthan us...

100 1-6. Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type alarm system. ■ Items to check before locking the vehicle To prevent unexpected triggering of the alarm and vehicle theft, make sureof the following: ● Nobody is in the vehicle. ● The windows and moon roof a...

101 1-6. Theft deterrent system 1 Before driving ■ Triggering of the alarm The alarm may be triggered in the following situations. (Stopping the alarm deactivates the alarm system.) ■ When the battery is disconnected Be sure cancel the alarm system.If the battery is disconnected before canceling the...

102 1-6. Theft deterrent system ■ Panic mode Vehicles with smart key system Vehicles without smart key system NOTICE ■ To ensure the system operates correctly Do not modify or remove the system. If modified or removed, the properoperation of the system cannot be guaranteed. When is pushed for longer...

104 1-7. Safety information Correct driving posture Drive with a good posture as follows: Sit upright and well back inthe seat. Adjust the position of theseat forward or backward toensure the pedals can bereached and easilydepressed to the extentrequired. ( → P. 59) Adjust the seatback so thatthe co...

106 1-7. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. Front airbags Driver airbag/...

107 1-7. Safety information 1 Before driving Airbag system components Front airbag sensor Front passenger airbag “AIR BAG ON” and “AIR BAGOFF” indicator lights Side airbag Curtain shield airbag Side and curtain shield airbagsensor SRS warning light Curtain shield airbag sensor Driver’s seat position...

109 1-7. Safety information 1 Before driving ■ Operating conditions (front airbags) ● The SRS front airbags will deploy in the event of an impact that exceedsthe set threshold level (the level of force corresponding to an approxi-mately 12 - 18 mph [20 - 30 km/h] frontal collision with a fixed wall ...

112 1-7. Safety information ■ When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ● The front of the vehicle is damaged ordeformed, or was involved in an acci-dent that was not severe enough tocause t...

113 1-7. Safety information 1 Before driving CAUTION ■ SRS airbag precautions Observe the following precautions regarding the airbags.Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat beltsproperly.The SRS airbags are supplemental...

118 1-7. Safety information CAUTION ■ Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modificationswithout consulting your Toyota dealer. The SRS airbag may malfunction or deploy (inflate) accidentally, causingdeath or serious ...

119 1 1-7. Safety information Before driving Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for front passenger....

121 1-7. Safety information 1 Before driving ■ Unoccupied ■ System malfunction Indicator/ warning light “AIR BAG ON” and “AIR BAG OFF” indicator lights Not illuminated SRS warning light Off Front passenger’s seat belt reminder light Devices Front passenger airbag Deactivated Side airbag on the front...

122 1-7. Safety information * 1 : The system judges a person of adult size as an adult. When asmaller adult sits in the front passenger seat, the system mayrecognize him/her as a child depending on his/her physique andposture. * 2 : In the event the front passenger does not wear a seat belt. * 3 : W...

123 1-7. Safety information 1 Before driving CAUTION ■ Front passenger occupant classification system precautions Observe the following precautions regarding front passenger occupant clas-sification system.Failure to do so may cause death or serious injury. ● Wear the seat belt properly. ● Make sure...

124 1-7. Safety information CAUTION ■ Front passenger occupant classification system precautions ● Do not recline the front passenger seatback so far that it touches a rearseat. This may cause the “AIR BAG OFF” indicator light to be illuminated,which indicates that the passenger’s airbags will not d...

125 1 1-7. Safety information Before driving Child restraint systems Points to remember Studies have shown that installing a child restraint on a rear seat ismuch safer than installing one to the front passenger seat. ● Choose a child restraint system that suits your vehicle and isappropriate to the...

126 1-7. Safety information Types of child restraints Child restraint systems are classified into the following 3 typesaccording to the age and size of the child. Rear-facing ⎯ Infant seat/convertible seat Forward-facing ⎯ Convertible seat Booster seat

127 1-7. Safety information 1 Before driving ■ Selecting an appropriate child restraint system ● Use a child restraint system appropriate for the child until the childbecomes large enough to properly wear the vehicle’s seat belt. ● If a child is too large for a child restraint system, sit the child ...

129 1-7. Safety information 1 Before driving CAUTION ■ Child restraint lock function belt precaution Do not allow children to play with the child restraint lock function belt. If thebelt becomes twisted around a child’s neck, it will not be possible to pull thebelt out leading to choking or other se...

130 1-7. Safety information Installing child restraints Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the outboard rear seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder bel...

131 1-7. Safety information 1 Before driving Installation with LATCH system Adjust the seatback as leaned aspossible. Widen the gap between the seat cushion and seatbackslightly. Type A Latch the hooks of the lowerstraps onto the LATCH anchors. STEP 1 As leaned as possible STEP 2 STEP 3 Canada only

132 1-7. Safety information If the child restraint has a top tether strap, the top tether strapshould be latched onto the top tether anchors. For owners in Canada: The symbol on a child restraint system indicates the presence of alower connector system. Type B Latch the buckles onto theLATCH anchors...

134 1-7. Safety information While pushing the child restraintsystem down into the rear seat,allow the shoulder belt to retractuntil the child seat is securely inplace. After the shoulder belt hasretracted to a point where there isno slack in the belt, pull the belt tocheck that it cannot be extended...

136 1-7. Safety information ■ Booster seat Place the booster seat on theseat facing the front of the vehi-cle. Sit the child in the booster seat.Fit the seat belt to the boosterseat according to the manufac-turer’s instructions and insert theplate into the buckle. Make surethat the belt is not twist...

137 1-7. Safety information 1 Before driving Removing a child restraint installed with a seat belt Push the buckle release buttonand fully retract the seat belt. Child restraint systems with a top tether strap Secure the child restraint using aseat belt or LATCH anchors, andlock the head restraint i...

138 1-7. Safety information ■ Laws and regulations pertaining to anchorages The LATCH system conforms to FMVSS225 or CMVSS210.2.Child restraint systems conforming to FMVSS213 or CMVSS213 specifica-tions can be used.This vehicle is designed to conform to the SAE J1819. CAUTION ■ When installing a boo...

139 1-7. Safety information 1 Before driving CAUTION ■ When installing a child restraint system ● When a booster seat is installed, always ensure that the shoulder belt ispositioned across the center of the child’s shoulder. The belt should bekept away from the child’s neck, but not so that it could...

140 1-7. Safety information CAUTION ■ Do not use a seat belt extender If a seat belt extender is used when installing a child restraint system, theseat belt will not securely hold the child restraint system, which could causedeath or serious injury to the child or other passengers in the event of su...

142 2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing. ■ Starting the engine → P. 154, 158 ■ Driving With the brake pedal depressed, shift the shift lever to “D”. ( → P. 161) Release the parking brake. ( → P. 167) Gradually release the b...

143 2-1. Driving procedures 2 Wh en drivin g Starting on a steep incline Firmly set the parking brake and shift the shift lever to “D”. Gently depress the accelerator pedal. Release the parking brake. ■ Driving in the rain ● Drive carefully when it is raining, because visibility will be reduced, the...

145 2-1. Driving procedures 2 Wh en drivin g CAUTION ■ When starting the vehicle Always keep your foot on the brake pedal while stopped with the engine run-ning. This prevents the vehicle from creeping. ■ When driving the vehicle ● Do not drive if you are unfamiliar with the location of the brake an...

146 2-1. Driving procedures CAUTION ■ When driving the vehicle ● If the smell of exhaust is noticed inside the vehicle, open the windows andcheck that the trunk is closed. Large amounts of exhaust in the vehicle can cause driver drowsiness andan accident, resulting in death or a serious health hazar...

148 2-1. Driving procedures CAUTION ■ When shifting the shift lever Be careful not to shift the shift lever with the accelerator pedal depressed.This may lead to unexpected rapid acceleration of the vehicle that maycause an accident and result in death or serious injury. ■ When the vehicle is stoppe...

149 2-1. Driving procedures 2 Wh en drivin g CAUTION ■ When the vehicle is parked ● Do not leave glasses, cigarette lighters, spray cans, or soft drink cans inthe vehicle when it is in the sun.Failure to do so may result in the following: • Gas may leak from a cigarette lighter or spray can, and may...

150 2-1. Driving procedures CAUTION ■ Exhaust gases Exhaust gases include harmful carbon monoxide (CO) that is colorless andodorless. Inhaling exhaust gases may lead to death or a serious health haz-ard. ● If the vehicle is in a poorly ventilated area, stop the engine. In a closedarea, such as a gar...

151 2-1. Driving procedures 2 Wh en drivin g CAUTION ■ When braking the vehicle ● When the brakes are wet, drive more cautiously. Braking distance increases when the brakes are wet, and may cause oneside of the vehicle to brake differently than the other side. Also the parkingbrake may not securely ...

152 2-1. Driving procedures NOTICE ■ When parking the vehicle Always put the shift lever in “P”. Failure to do so may cause the vehicle tomove or the vehicle may accelerate suddenly if the accelerator pedal is acci-dentally depressed. ■ Avoiding damage to vehicle parts ● Do not turn the steering whe...

153 2-1. Driving procedures 2 Wh en drivin g NOTICE ■ When encountering flooded roads Do not drive on a road that has flooded after heavy rain etc. Doing so maycause the following serious damage to the vehicle. ● Engine stalling ● Short in electrical components ● Engine damage caused by water immers...

154 2-1. Driving procedures Engine (ignition) switch (with smart key system) Performing the following operations when carrying the electronic key on your person starts the engine or changes “ENGINE START STOP” switch modes. ■ Starting the engine Check that the parking brake is set. Check that the sh...

155 2-1. Driving procedures 2 Wh en drivin g ■ Changing engine (ignition) switch mode Modes can be changed by pressing the “ENGINE STARTSTOP” switch with the brake pedal released. (The modechanges each time the switch is pressed.) OFF * Emergency flashers can beused. ACCESSORY mode Some electrical c...

156 2-1. Driving procedures ■ When the steering lock cannot be released ■ If the engine does not start The engine immobilizer system may not have been deactivated. ( → P. 96) ■ When the “ENGINE START STOP” switch indicator flashes in amber The system may be malfunctioning. Have the vehicle inspected...

157 2-1. Driving procedures 2 Wh en drivin g CAUTION ■ When starting the engine Always start the engine while sitting in the driver’s seat. Do not press theaccelerator pedal while starting the engine under any circumstances.Doing so may cause an accident resulting in death or serious injury. ■ Stopp...

158 2-1. Driving procedures Engine (ignition) switch (without smart key system) ■ Starting the engine Check that the parking brake is set. Check that the shift lever is set in “P”. Sit in the driver’s seat and firmly depress the brake pedal. Turn the engine switch to the “START” position and startth...

159 2-1. Driving procedures 2 Wh en drivin g ■ Turning the key from “ACC” to “LOCK” Shift the shift lever to “P”. ■ When the steering lock cannot be released ■ If the engine does not start The engine immobilizer system may not have been deactivated. ( → P. 96) ■ Key reminder function A buzzer sounds...

160 2-1. Driving procedures CAUTION ■ When starting the engine Always start the engine while sitting in the driver’s seat. Do not press theaccelerator pedal while starting the engine under any circumstances.Doing so may cause an accident resulting in death or serious injury. ■ While driving Do not t...

161 2-1. Driving procedures 2 Wh en drivin g Automatic transmission Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever Vehicles with smart key system: While the “ENGINE START STOP” switch is in IGNITIONON mode, depress the brake pedal and move the shiftlever. ...

162 2-1. Driving procedures ■ Shift position uses * 1 : Shifting to the D position allows the system to select a gear suitable for the driving conditions.Setting the shift lever to the D position is recommended for normal driv-ing. * 2 : Selecting shift ranges using S mode restricts the upper limit ...

163 2-1. Driving procedures 2 Wh en drivin g Changing shift ranges in S mode Shift the shift lever to the S mode driving position and operate theshift lever. Upshifting Downshifting The initial shift range in S mode is set automatically to 5 or 4 accord-ing to vehicle speed. However, the initial shi...

164 2-1. Driving procedures ■ Shift ranges and their functions ● Automatically selecting gears between 1 and 6 according tovehicle speed and driving condition. (However the gear is limitedaccording to selected shift range.) ● You can choose from 6 levels of engine braking force. ● A lower shift rang...

165 2-1. Driving procedures 2 Wh en drivin g ■ If the S indicator does not come on even after shifting the shift lever to S mode driving position This may indicate a malfunction in the automatic transmission system. Havethe vehicle inspected by your Toyota dealer immediately. (In this situation, the...

166 2-1. Driving procedures Turn signal lever ■ Turn signals can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. ■ If the indicators flash faster than usual Check that ...

167 2-1. Driving procedures 2 Wh en drivin g Parking brake ■ Usage in winter time See “Winter driving tips” for parking brake usage in winter time. ( → P. 219) NOTICE ■ Before driving Fully release the parking brake.Driving the vehicle with the parking brake set will lead to brake componentsoverheat...

168 2-1. Driving procedures Horn To sound the horn, press on orclose to the mark.

169 2 Wh en drivin g 2-2. Instrument cluster Gauges and meters The units used on the speedometer may differ depending on thetarget region. Engine coolant temperature gauge Displays the engine coolant temperature. Tachometer Displays the engine speed in revolutions per minute. Shift position indicato...

170 2-2. Instrument cluster Odometer and trip meter display button Vehicles with smart key system Pressing this button switches among odometer and trip meter whenthe “ENGINE START STOP” switch is IGNITION ON mode. Vehicles without smart key system Pressing this button switches among odometer and tri...

171 2-2. Instrument cluster 2 Wh en drivin g Instrument panel light control The brightness of the instrument panel lights can be adjusted. Darker Brighter NOTICE ■ To prevent damage to the engine and its components ● Do not let the indicator needle of the tachometer enter the red zone, whichindicate...

172 2-2. Instrument cluster Indicators and warning lights The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. Instrument cluster The units used on the speedometer and some indicators may differdepending on ...

173 2-2. Instrument cluster 2 Wh en drivin g ■ Indicators The indicators inform the driver of the operating state of thevehicle’s various systems. * 1 : These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with smart key system) orthe engine switch is turn...

174 2-2. Instrument cluster CAUTION ■ If a safety system warning light does not come on Should a safety system light such as ABS and the SRS airbag warning lightnot come on when you start the engine, this could mean that these systemsare not available to help protect you in an accident, which could ...

175 2-2. Instrument cluster 2 Wh en drivin g Multi-information display Switching the display Items displayed can be switchedby pressing the “DISP” button. The multi-information display presents the driver with a variety of driving-related data including the current outside air temperature. ● Outside...

176 2-2. Instrument cluster Display items ■ Outside temperature ■ Driving range ■ Average fuel consumption ■ Current fuel consumption Displays the outside air temperature The temperature range that can be displayed is from-40 ° F (-40 ° C) up to 122 ° F (50 ° C). Displays the estimated maximum dista...

177 2-2. Instrument cluster 2 Wh en drivin g ■ Average vehicle speed Displays the average vehicle speed since theengine was started or the function was reset The function can be reset by pressing the “DISP” but-ton for longer than 1 second when the average vehi-cle speed is displayed. ■ Outside temp...

178 2-3. Operating the lights and windshield wipers Headlight switch The headlights can be operated manually or automatically. Type A The headlights,parking lights, day-time running lightsand so on turn onand off automati-cally. (When the“ENGINE STARTSTOP” switch is inIGNITION ON mode[vehicles with ...

180 2-3. Operating the lights and windshield wipers Turning on the high beam headlights With the headlights on, pushthe lever forward to turn on thehigh beams. Pull the lever back to the centerposition to turn the high beamsoff. Pull the lever toward you toturn on the high beams. Release to turn the...

181 2-3. Operating the lights and windshield wipers 2 Wh en drivin g ■ Automatic light off system Vehicles with smart key system The headlights and tail lights turn off 30 seconds after a door is opened orclosed if the “ENGINE START STOP” switch has been turned to ACCES-SORY or turned OFF while the ...

182 2-3. Operating the lights and windshield wipers Fog light switch The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam. Type A OFF ON

184 2-3. Operating the lights and windshield wipers Windshield wipers and washer (Type A) ■ Intermittent wiper with interval adjuster (if equipped) Wiper intervals can be adjusted for intermittent operation (when is selected). Intermittent wiperoperation Low speed wiperoperation High speed wiperoper...

185 2-3. Operating the lights and windshield wipers 2 Wh en drivin g Wash/wipe operation Wipers will automatically oper-ate a couple of times after thewasher squirts. ■ Raindrop detection windshield wipers (if equipped) With “AUTO” selected, the wipers will operate automaticallywhen the sensor detec...

186 2-3. Operating the lights and windshield wipers ■ The windshield wiper and washer can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. Sensor sensitivity (high) Sens...

187 2-3. Operating the lights and windshield wipers 2 Wh en drivin g ■ Effects of vehicle speed on wiper operation Vehicle speed affects the following even when the wipers are not in “AUTO”mode. ● Intermittent wiper interval ( mode) ● Wiper operation when the washer is being used With low speed mode...

188 2-3. Operating the lights and windshield wipers CAUTION ■ Caution regarding the use of windshield wipers in “AUTO” mode The windshield wipers may operate unexpectedly if the sensor is touched orthe windshield is subject to vibration in “AUTO” mode. Take care that yourfingers or anything else do ...

189 2-3. Operating the lights and windshield wipers 2 Wh en drivin g Windshield wipers and washer (Type B) ■ Intermittent wiper with interval adjuster (if equipped) Wiper intervals can be adjusted for intermittent operation (when is selected). Intermittent wiperoperation Low speed wiperoperation Hig...

194 2-4. Using other driving systems Cruise control Use the cruise control to maintain a set speed without using the accelerator. Indicator Cruise control switch ■ Set the vehicle speed Press the “ON-OFF” button toactivate the cruise control. Press the button once more todeactivate the cruise contro...

195 2-4. Using other driving systems 2 Wh en drivin g ■ Adjusting the speed setting To change the set speed, operate the lever until the desired setspeed is obtained. Increase speed Decrease speed Fine adjustment. Momentarilymove the lever in the desireddirection. Large adjustment. Hold thelever in ...

196 2-4. Using other driving systems ■ Cruise control can be set when ● The shift lever is in the “D” or range “4” or higher of “S” has beenselected. ● Vehicle speed is above approximately 25 mph (40 km/h). ■ Accelerating ● The vehicle can be accelerated normally. After acceleration, the setspeed re...

197 2-4. Using other driving systems 2 Wh en drivin g ■ Automatic cruise control cancelation The set speed is automatically canceled in any of the following situations. ● Actual vehicle speed falls more than 10 mph (16 km/h) below the presetvehicle speed.At this time, the memorized set speed is not ...

198 2-4. Using other driving systems Rear view monitor system ∗ ∗ : If equipped The rear view monitor system assists the driver by displaying an image of the view behind the vehicle while reversing. The image is displayed in reverse on the screen. This allows the image to appear in the same manner a...

199 2-4. Using other driving systems 2 Wh en drivin g ■ Switching the screen ■ When using the rear view monitor system The anti-glare function of the inside rear view mirror will be canceled. ■ Automatic shut off The display will be turned off automatically after 5 minutes. ■ Display mode The rear v...

201 2-4. Using other driving systems 2 Wh en drivin g ■ Displayed area ■ Driving precautions The area covered by the camera is lim-ited. Objects which are close to eithercorner of the bumper or under thebumper cannot be seen on the screen. The area displayed on the screen mayvary according to vehicl...

203 2-4. Using other driving systems 2 Wh en drivin g ■ Rear view monitor guide lines Guide lines are displayed on the screen. Guide lines shown differ from those shown on the actual screen. Vehicle width extension guide lines (blue)These lines indicate the estimated vehicle width extension. Distanc...

204 2-4. Using other driving systems ■ Rear view monitor system camera In the following cases, it may be difficultto see the images on the screen, evenwhen the system is functioning correctly. • In the dark (e.g. at night).• If the temperature near the lens is extremely high or low. • If water dropl...

205 2-4. Using other driving systems 2 Wh en drivin g CAUTION ■ When using the rear view monitor system Observe the following precautions to avoid an accident that could result indeath or serious injuries. ● Never depend solely on the monitor system when reversing. ● Always check visually and with t...

206 2-4. Using other driving systems CAUTION ■ Conditions which may affect the rear view monitor system ● If the back of the vehicle is hit, the camera’s position and mounting anglemay change. Contact your Toyota dealer. ● Rapid temperature changes, such as when hot water is poured on thevehicle in ...

207 2-4. Using other driving systems 2 Wh en drivin g Driving assist systems When the VSC/TRAC/TRC are operating If the vehicle is in danger of slip-ping, or if the front wheels spin,the slip indicator light flashes toindicate that the VSC/TRAC/TRC have been engaged. To help enhance driving safety a...

208 2-4. Using other driving systems To disable TRAC/TRC and/or VSC If the vehicle gets stuck in fresh snow or mud, TRAC/TRC and VSCmay reduce power from the engine to the wheels. You may need toturn the system off to enable you to rock the vehicle in order to free it. ■ Turning off TRAC/TRC Quickly...

209 2-4. Using other driving systems 2 Wh en drivin g ■ When the “TRAC OFF” indicator light or “TRC OFF” indicator lightcomes on even if the VSC OFF switch has not been pressed TRAC orTRC cannot be operated. Contact your Toyota dealer. ■ Automatic reactivation of TRAC/TRC and VSC Vehicles with smart...

210 2-4. Using other driving systems CAUTION ■ The ABS does not operate effectively when ● The limits of tire gripping performance have been exceeded. ● The vehicle hydroplanes while driving at high speed on the wet or slickroad. ■ Stopping distance when the ABS is operating on the wet or slick road...

211 2-4. Using other driving systems 2 Wh en drivin g CAUTION ■ When the VSC is activated The slip indicator light flashes. Always drive carefully.Reckless driving may cause an accident. Exercise particular care when theindicator light flashes. ■ Replacing tires Make sure that all tires are of the s...

212 2-5. Driving information Cargo and luggage Capacity and distribution Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) – (Total weight of occupants) Steps for Determining Correct Load Limit— (1) Locate the statement “The combined weight of occu...

214 2-5. Driving information Example on your vehicle Cargo capacity Total load capacity When 2 people with the combined weight of 366 lb. (166 kg) areriding in your vehicle, which has a total load capacity of 870 lb. (395kg), the available amount of cargo and luggage load capacity will beas follows:...

215 2-5. Driving information 2 Wh en drivin g CAUTION ■ Things that must not be carried in the trunk The following things may cause a fire if loaded in the trunk. ● Receptacles containing gasoline ● Aerosol cans ■ Storage precautions Observe the following precautions.Failing to do so may result in d...

216 2-5. Driving information CAUTION ■ Weight of the load ● Do not exceed the maximum axle weight rating or the total vehicleweight rating. ● Even if the total load of occupant’s weight and the cargo load is lessthan the total load capacity, do not apply the load unevenly. Improperloading may cause ...

217 2-5. Driving information 2 Wh en drivin g Vehicle load limits Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ■ Total load capacity: 870 lb. (395 kg) Total load capacity means the combined weight of occupants,cargo and luggage. ■ Seating cap...

218 2-5. Driving information ■ Total load capacity and seating capacity These details are also described on the tire and loading informationlabel. ( → P. 430) CAUTION ■ Overloading the vehicle Do not overload the vehicle.It may not only cause damage to the tires, but also degrade steering andbraking...

219 2-5. Driving information 2 Wh en drivin g Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations ● Use fluids that are approp...

220 2-5. Driving information ■ Before driving the vehicle Perform the following according to the driving conditions. ● Do not try to forcibly open a window or move a wiper that isfrozen. Pour warm water over the frozen area to melt the ice.Wipe away the water immediately to prevent it from freezing....

221 2-5. Driving information 2 Wh en drivin g Selecting snow chains Use the correct snow chain size when mounting the snow chains.Chain size is regulated for each tire size. Side chain: 0.12 in. (3.0 mm) 1.18 in. (30.0 mm) 0.39 in. (10.0 mm) Cross chain: 0.16 in. (4.0 mm) 0.98 in. (25.0 mm) 0.55 in....

222 2-5. Driving information ■ Snow chain installation Observe the following precautions when installing and removing chains. ● Install and remove tire chains in a safe location. ● Install tire chains on the front tires only. ● Install tire chains following the instructions provided in the accompany...

223 2-5. Driving information 2 Wh en drivin g NOTICE ■ Repairing or replacing snow tires Request repairs of and obtain replacement snow tires from Toyota dealers.This is because the removal and attachment of snow tires affects the opera-tion of the tire pressure warning valves and transmitters. ■ Fi...

224 2-5. Driving information Trailer towing Toyota does not recommend towing a trailer with your vehicle. Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc. Your Toyota is not designed for trailer towing or for th...

225 2-5. Driving information 2 Wh en drivin g Dinghy towing NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground. Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

228 3-1. Using the air conditioning system and defogger Automatic air conditioning system Using the automatic mode Press . The air conditioning system will begin to operate. Air outlets and fanspeed are automatically adjusted according to the temperature set-ting. Airflow and outlets are automatical...

229 3-1. Using the air conditioning system and defogger 3 Inte rior fe atures Turning to the right increase the temperature and turn- ing to the left decrease the temperature. The temperature for the driver and passenger seats can be set sep-arately. Adjusting the settings ■ Adjusting the temperatur...

230 3-1. Using the air conditioning system and defogger ■ Changing the air outlets Press . The air outlets switch each timethe button is pressed. The air flowshown on the display indicate thefollowing. Air flows to the upper body. Air flows to the upper body andfeet.

231 3-1. Using the air conditioning system and defogger 3 Inte rior fe atures Air flows to the feet. Air flows to the feet and thewindshield defogger operates. ■ Switching between outside air and recirculated air modes Press . The mode switches between outside air mode (indicator off) and recircu-la...

232 3-1. Using the air conditioning system and defogger Defogging the windshield Press . The air conditioning system con-trol operates automatically.

233 3-1. Using the air conditioning system and defogger 3 Inte rior fe atures Adjusting the position of and opening and closing the air outlets Center outlets Turn the knob to open or closethe vent Direct air flow to the left orright, up or down Side outlets Direct air flow to the up ordown Direct a...

235 3-1. Using the air conditioning system and defogger 3 Inte rior fe atures CAUTION ■ To prevent the windshield from fogging up Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the wind-shield can cause the outer...

236 3-1. Using the air conditioning system and defogger Using the steering wheel climate control switches Using the automatic mode Press . The air conditioning system will begin to operate. Air outlets andfan speed are automatically adjusted according to the tempera-ture setting. Press “ ∧ ” to incr...

237 3-1. Using the air conditioning system and defogger 3 Inte rior fe atures Rear window and outside rear view mirror defoggers These features are used to defog the rear window, and to remove raindrops, dew and frost from the outside rear view mirrors. Press the button to turn on therear window and...

238 3-1. Using the air conditioning system and defogger ■ Operating conditions Vehicles with smart key system The “ENGINE START STOP” switch must be in IGNITION ON mode. Vehicles without smart key system The engine switch must be in the “ON” position. CAUTION ■ When the outside rear view mirror defo...

239 3 Inte rior fe atures 3-2. Using the audio system Audio system type With navigation system Owners of models equipped with a navigation system shouldrefer to the “Navigation System Owner’s Manual”. Without navigation system Type A: CD player with changer and AM/FM radio

241 3-2. Using the audio system 3 Inte rior fe atures Language settings The language used for all voice guidance, voice recognition and mes-sages may be changed. Press . Press that corresponds to “MORE”. Press that corresponds to “LANG”. Press that corresponds to the desired language. For vehicles s...

242 3-2. Using the audio system CAUTION ■ For vehicles sold in the U.S.A. ● Part 15 of the FCC Rules FCC Warning:Any unauthorized changes or modifications to this equipment will void theuser’s authority to operate this device. ● Laser products • Do not take this unit apart or attempt to make any cha...

243 3-2. Using the audio system 3 Inte rior fe atures Using the radio Selecting the preset station pages Displaying text messages AM/FM/SAT mode button Changing the category (SAT mode) Station selector Power Volume Adjusting the frequency (AM, FM mode) or channel (SAT mode) Scanning for receivable s...

244 3-2. Using the audio system Setting station presets (excluding XM ® Satellite Radio) Search for desired stations by turning or pressing “ ∧ ” or “ ∨ ” on . Press and hold the button (one of ) the station is to be set to, and you hear a beep. Each preset page may contain AM, FM, or XM radio stati...

245 3-2. Using the audio system 3 Inte rior fe atures Scanning radio stations (excluding XM ® Satellite Radio) ■ Scanning the preset radio stations Press and hold until you hear a beep. Preset stations will be played for a few seconds each. When the desired station is reached, press once again. ■ Sc...

247 3-2. Using the audio system 3 Inte rior fe atures ■ Scanning XM ® Satellite Radio channels ● Scanning channels in the current category Press . When the desired channel is reached, press the button again. ● Scanning preset channels Press and hold until you hear a beep. When the desired channel is...

249 3-2. Using the audio system 3 Inte rior fe atures ■ If the satellite radio does not operate normally If a problem occurs with the XM ® tuner, a message will appear on the dis- play. Refer to the table below to identify the problem, and take the suggestedcorrective action. CHECK ANTENNA The XM ® ...

250 3-2. Using the audio system Contact the XM ® Listener Care Center at 1-800-967-2346 (U.S.A.) or 1-877- 209-0079 (Canada). ■ Certifications for the radio tuner This equipment has been tested and found to comply with the limits for aclass B digital device, pursuant to Part 15 of the FCC Rules. The...

251 3-2. Using the audio system 3 Inte rior fe atures Using the CD player Selector buttons CD load (type A only) Displaying text messages Searching playback Playback Playback/pause Fast-forwarding and reversing/Selecting a track CD eject Power Volume

252 3-2. Using the audio system Loading a CDs ■ Loading a single CD Type A Press . When the indicator on the slot turns from amber to green,insert a CD. Type B Insert a CD. ■ Loading multiple CDs (type A only) Press and hold until you hear a beep. Insert a CD when the indicator on the slot turns fro...

253 3-2. Using the audio system 3 Inte rior fe atures Ejecting CDs ■ Ejecting a CD Type A To select the CD to be ejected, press that corresponds to “ ” or “ ”. The selected CD number is shown on the display. Press and remove the CD. Type B Press and remove the CD. ■ Ejecting all CDs (type A only) Pr...

254 3-2. Using the audio system Selecting a track Press “ ∧ ” to move up or “ ∨ ” to move down using until the desired track number appears on the display. Fast-forwarding and rewinding tracks Press and hold “ ∧ ” or “ ∨ ” on . Scanning a CD Press . The first 10 seconds of each track will be played....

255 3-2. Using the audio system 3 Inte rior fe atures Random playback ■ Current CD Press that corresponds to “RDM”. Songs are played in random order. To cancel, press the button again. ■ All CDs (type A only) Press that corresponds to “RDM” twice. Tracks on all loaded CDs are played in random order....

256 3-2. Using the audio system ■ Error messages “READ ERROR”: This indicates a trouble either in the CD or inside the player. The CD may be dirty, damaged or inserted up-sidedown. “PLEASE WAIT”: Operation has stopped due to a high temperature inside the player. Wait for a while and then press . Con...

257 3-2. Using the audio system 3 Inte rior fe atures NOTICE ■ CDs and adapters that cannot be used Do not use the following types of CDs, 3 in. (8 cm) CD adapters or DualDisc. Doing so may damage the player and/or the CD insert/eject function. ● CDs that have a diameter that is not 4.7in. (12 cm). ...

258 3-2. Using the audio system NOTICE ■ Player precautions Failure to follow the precautions below may result in damage to the CDs orthe player itself. ● Do not insert anything other than CDs into the CD slot. ● Do not apply oil to the player. ● Store CDs away from direct sunlight. ● Never try to d...

259 3-2. Using the audio system 3 Inte rior fe atures Playing back MP3 and WMA discs Loading and ejecting MP3 and WMA discs → P. 251 Selecting a CD (type A only) → P. 251 Playback CD eject Playback/pause Searching playback Displaying text messages Selecting a folder CD load (type A only) Selecting a...

260 3-2. Using the audio system Selecting and scanning a folder ■ Selecting folders one at a time Press “ ∧ ” or “ ∨ ” on to select the desired folder. To return to the first folder, press and hold “ ∨ ” on until you hear a beep. ■ Selecting the desired folder by cueing the first file of eachfolder ...

262 3-2. Using the audio system Switching the display Press . Each time is pressed, the display changes in the order of Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time. ■ Display → P. 255 ■ Error messages “READ ERROR”: This indicates a trouble either in the ...

266 3-2. Using the audio system ● Extensions If the file extensions .mp3 and .wma are used for files other than MP3 andWMA files, they will be mistakenly recognized and played as MP3 andWMA files. This may result in large amounts of interference and damageto the speakers. ● Playback • To play MP3 fi...

267 3-2. Using the audio system 3 Inte rior fe atures Operating an iPod Connecting an iPod enables you to enjoy music from the vehicle speakers. ■ Connecting an iPod Open the cover and connectan iPod using an iPod cable. Turn on the power of the iPod ifit is not turned on. Press . ■ Control panel ST...

268 3-2. Using the audio system Selecting a play mode Press that corresponds to “BROWSE” to select iPod menu mode. Press that corresponds to the desired play mode. ■ Play mode list Depending on the model, the name of your iPod may be displayed atthe top of the list. STEP 1 STEP 2 Play mode First sel...

269 3-2. Using the audio system 3 Inte rior fe atures Selecting songs from a song list Press that corresponds to “LIST”. The current playlist is displayed. Turning to select the desired song. Press returns the screen from list display to the previous screen. Selecting songs Turn or press “ ∧ ” or “ ...

270 3-2. Using the audio system Shuffle playback ■ Playing songs from one playlist or album in random order Press that corresponds to “RDM”. To cancel, press the button twice. ■ Playing songs from all the playlists or albums in random order Press that corresponds to “RDM” twice. To cancel, press the...

271 3-2. Using the audio system 3 Inte rior fe atures ■ About iPod ● Apple is not responsible for the operation of this device or its compliancewith safety and regulatory standards. ● iPod is a trademark of Apple Inc., registered in the U.S. and other coun-tries. ■ iPod functions ● When an iPod is c...

273 3-2. Using the audio system 3 Inte rior fe atures CAUTION ■ While driving Do not connect iPod or operate the controls. NOTICE ■ To prevent damage to iPod ● Do not leave iPod in the vehicle. The temperature inside the vehicle maybecome high, resulting in damage to the player. ● Do not push down o...

274 3-2. Using the audio system Operating a USB memory Connecting a USB memory enables you to enjoy music from the vehicle speakers. ■ Connecting a USB memory Open the cover and connect aUSB memory. Turn on the power of the USBmemory if it is not turned on. Depending on the USB device,a USB extensio...

277 3-2. Using the audio system 3 Inte rior fe atures Switching the display Press . Each time the button is pressed, the display changes in the followingorder: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time. ■ When using the USB port You may be unable to us...

278 3-2. Using the audio system ■ USB memory ● Compatible devices USB memory that can be used for MP3 and WMA playback. Depending on the type of USB device, playback may not be possible. ● Compatible device formats The following device formats can be used: • USB communication formats: USB2.0 FS (12m...

281 3-2. Using the audio system 3 Inte rior fe atures CAUTION ■ While driving Do not connect USB memory or operate the controls. NOTICE ■ To prevent damage to USB memory ● Do not leave USB memory in the vehicle. The temperature inside the vehi-cle may become high, resulting in damage to the player. ...

282 3-2. Using the audio system Optimal use of the audio system Using the audio control function ■ Changing modes Press . Press that corresponds to the desired mode. “BASS”, “MID” (type A only), “TREB”, “FADE” or “BAL” Selector buttons Adjusting the sound quality Menu button Power Volume STEP 1 STEP...

283 3-2. Using the audio system 3 Inte rior fe atures ■ Adjusting sound quality Turning adjusts the level. * : The sound quality level is adjusted individually in each audio mode. Mode displayed Sound quality mode Level Turn to the left Turn to the right BASS Bass * -5 to 5 Low High MID Mid-range * ...

284 3-2. Using the audio system ■ Adjusting the Automatic Sound Levelizer (ASL) Press . Press that corresponds to “MORE”. Press that corresponds to “ASL”. Press that corresponds to the desired mode. Type A: “ON” or “OFF” ASL automatically adjusts the volume and tone quality according to vehi-cle spe...

285 3-2. Using the audio system 3 Inte rior fe atures Using the AUX port ■ Operating portable audio devices connected to the audio system The volume can be adjusted using the vehicle’s audio controls. All otheradjustments must be made on the portable audio device itself. This port can be used to con...

286 3-2. Using the audio system Using the steering switches Some audio features can be controlled using the switches on the steering wheel. Increases/decreases vol-ume Radio mode: Selects radio stations CD mode: Selects tracks files(MP3 and WMA) anddiscs iPod mode: Selects a song USB memory mode: Se...

287 3-2. Using the audio system 3 Inte rior fe atures Turning on the power Press when the audio system is turned off. The audio system can be turned off by holding the switch down until youhear a beep. Changing the audio source Press when the audio system is turned on. The audio source changes as fo...

288 3-2. Using the audio system Selecting a track/file or song Press to select the CD, iPod, USB memory or Bluetooth ® audio mode. Press “ ∧ ” or “ ∨ ” on to select the desired track/file or folder. Selecting a folder or album Press to select the CD, USB memory or Bluetooth ® audio mode. Press and h...

289 3 Inte rior fe atures 3-3. Using the Bluetooth ® audio system Bluetooth ® audio system The Bluetooth ® audio system enables you to enjoy music played on a portable digital audio player (portable player) from the vehicle speakers via wireless communication. This audio system supports Bluetooth ® ...

290 3-3. Using the Bluetooth ® audio system ■ Conditions under which the system will not operate ● If using a portable player that does not support Bluetooth ® ● If the portable player is switched off ● If the portable player is not connected ● If the portable player’s battery is low ● If the portab...

291 3-3. Using the Bluetooth ® audio system 3 Inte rior fe atures ■ Certification for the Bluetooth ® audio system Type AFCC ID: BABFT0001AIC ID: 2024B-FT0001AMADE IN CHINA Type BFCC ID: L2C0045TRIC ID: 3432A-0045TRMADE IN MEXICO This device complies with Part 15 of the FCC Rules and RSS-210 Rules.O...

292 3-3. Using the Bluetooth ® audio system Using the Bluetooth ® audio system ■ Audio unit Display A message, name, number,etc. is displayed. Lower-case charactersand special characterscannot be displayed. Selects items such as menuand numberTurn: Selects an itemPress: Inputs the selecteditem Bluet...

293 3-3. Using the Bluetooth ® audio system 3 Inte rior fe atures ■ Steering wheel Volume The voice guidance volumecannot be adjusted by usingthis button. Talk switch Turns the voice command sys-tem on (press)/turns the voicecommand system off (pressand hold) ■ Microphone

294 3-3. Using the Bluetooth ® audio system Operating the system using voice commands By following voice guidance instructions output from the speaker, voice commands enable to the operation of the Bluetooth ® audio sys- tem without the need to check the display or operate . ■ Operation procedure wh...

296 3-3. Using the Bluetooth ® audio system Select “Confirm” using a voice command or . A passkey is displayed and heard, and a voice guidance instructionfor inputting the passkey into the portable player is heard. Input the passkey into the portable player. Refer to the manual that comes with the p...

297 3-3. Using the Bluetooth ® audio system 3 Inte rior fe atures Menu list of the Bluetooth ® audio system ■ Normal operation “BT•A Setup” can be canceled by pressing the on-hook switch or sayingthe voice command, “Cancel”. First menu Second menu Third menu Operation detail “Setup” “BT•A Setup” “Pa...

298 3-3. Using the Bluetooth ® audio system ■ When using a voice command For numbers, say a combination of single digits from zero to nine. Say the command correctly and clearly. ■ Situations that the system may not recognize your voice ● When driving on rough roads ● When driving at high speeds ● W...

299 3-3. Using the Bluetooth ® audio system 3 Inte rior fe atures Operating a Bluetooth ® enabled portable player ∗ Selecting an album Press “ ∨ ” or “ ∧ ” on . Selecting tracks Turn or press “ ∧ ” or “ ∨ ” on to select the desired track. ∗ : If equipped Playback/pause Displaying text messages Playb...

300 3-3. Using the Bluetooth ® audio system Playing and pausing tracks Press . Fast-forwarding and rewinding tracks Press and hold “ ∧ ” or “ ∨ ” on . Switching the display Press . Each time the button is pressed, the display changes in the followingorder: Track title → Track title/Artist name → Tra...

301 3-3. Using the Bluetooth ® audio system 3 Inte rior fe atures Setting up a Bluetooth ® enabled portable player ∗ ∗ : If equipped Registering a portable player in the Bluetooth ® audio system allows the system to function. The following functions can be used for reg- istered portable players: ■ F...

302 3-3. Using the Bluetooth ® audio system Registering a portable player Select “Pair Audio Player” using a voice command or , and perform the procedure for registering a portable player. ( → P. 295) Selecting a portable player to be used Select “Select Audio Player” using a voice command or . Sele...

303 3-3. Using the Bluetooth ® audio system 3 Inte rior fe atures Press the talk switch and say “From Car” or “From Audio”, and select “Confirm” by using a voice command or . Vehicles with smart key system: If “From Car” is selected, the porta-ble player will be automatically connected whenever the ...

304 3-3. Using the Bluetooth ® audio system Press the talk switch or select “Record Name” using , and say the new name. Select “Confirm” using a voice command or . Listing the registered portable players Select “List Audio Players” using a voice command or . The list of registered portable players w...

305 3-3. Using the Bluetooth ® audio system 3 Inte rior fe atures Changing the passkey Select “Set Passkey” using a voice command or . Press the talk switch, say a 4 to 8-digit number, and select “Confirm” using a voice command or . When the entire number to be registered as a passkey has been input...

306 3-3. Using the Bluetooth ® audio system Deleting a registered portable player Select “Delete Audio Player (Delete Audio)” using a voice command or . Select the portable player to be deleted by either of the follow-ing methods and select “Confirm” using a voice command or : a. Press the talk swit...

307 3-3. Using the Bluetooth ® audio system 3 Inte rior fe atures Bluetooth ® audio system setup ■ System setup items and operation procedures → P. 332

309 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures ■ Hands-free System Additional Information For additional information pairing and connecting cellular phone or for phonecompatibility with vehicle’s Bluetooth ® system, please visit the following website: http://www.toyo...

310 3-4. Using the hands-free system (for cellular phone) ■ Certification for the hands-free system Type AFCC ID: BABFT0001AIC ID: 2024B-FT0001AMADE IN CHINA Type BFCC ID: L2C0045TRIC ID: 3432A-0045TRMADE IN MEXICO This device complies with Part 15 of the FCC Rules and RSS-210 Rules.Operation is sub...

311 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Using the hands-free system ■ Audio unit Display A message, name, phonenumber, etc. is displayed. Lower-case characters andspecial characters, such asan umlaut, cannot be dis-played. Selects speed dials Selects items suc...

313 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Operating the system by using a voice command By following voice guidance instructions output from the speaker,voice commands can be given to allow for operation of the hands- free system without checking the display or ...

314 3-4. Using the hands-free system (for cellular phone) Using the hands-free system for the first time Before using the hands-free system, it is necessary to register a cel-lular phone in the system. The phone registration mode will beentered automatically when starting the system with no cellular...

318 3-4. Using the hands-free system (for cellular phone) ■ Using a short cut key First menu Second menu Operation detail Dial “XXX (name)” ⎯ Dialing a number registered in the phone book Dial “XXX (number)” ⎯ Dialing the input numbers Phone book add entry ⎯ Adding a new number Phone book change nam...

319 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures ■ Automatic adjustment of volume When vehicle speed is 50 mph (80 km/h) or more, the volume automaticallyincreases. The volume returns to the previous volume setting when vehiclespeed drops to 43 mph (70 km/h) or less. ■...

320 3-4. Using the hands-free system (for cellular phone) Making a phone call ■ Making a phone call ● Dialing by inputting a number“Dial by number” ● Dialing by inputting a name “Dial by name” ● Speed dialing ● Dialing a number stored in the outgoing history memory “Redial” ● Dialing a number stored...

321 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Dialing by inputting a number Press the talk switch and say “Dial by number”. Press the talk switch and say the phone number. Dial by one of the following methods: a. Press the off-hook switch. b. Press the talk switch a...

323 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Using the call history memory Follow the procedure below to use a number stored in the call historymemory: Press the talk switch and say “Redial” (when using a numberstored in the outgoing call history memory) or “Call b...

324 3-4. Using the hands-free system (for cellular phone) ■ Call history Up to 5 numbers can be stored in each of the outgoing and incoming historymemories. ■ When talking on the phone ● Do not talk simultaneously with the other party. ● Keep the volume of the receiving voice down. Otherwise, voice ...

325 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Setting a cellular phone Registering a cellular phone in the hands-free system allows the system to function. The following functions can be used for regis- tered cellular phones: ■ Functions and operation procedures To ...

327 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Changing a registered name Select “Change Name” by using a voice command or . Select a name of cellular phone to be changed by either of thefollowing methods: a. Press the talk switch and say the desired phone name, and ...

328 3-4. Using the hands-free system (for cellular phone) Listing the registered cellular phones Selecting “List Phones” by using a voice command or causes the list of registered cellular phones to be read aloud.When listing is complete, the system returns to “Phone Setup”. Pressing the talk switch ...

329 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Deleting a cellular phone Select “Delete Phone” by using a voice command or . Pattern A Select the cellular phone to be deleted by either of the follow-ing methods and select “Confirm” by using a voice command or : a. Pr...

330 3-4. Using the hands-free system (for cellular phone) Changing the passkey Select “Set Passkey” by using a voice command or . Pattern A Press the talk switch, say a 4 to 8-digit number, and select “Confirm” by using a voice command or . Pattern B Select a 4 to 8-digit number by using . The numbe...

331 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Turning the hands-free phone automatic connection on/off ■ Turning off the automatic connection Select “Hands-free Power” by using a voice command or . Select “Turn off” by using a voice command or . ■ Turning on the aut...

332 3-4. Using the hands-free system (for cellular phone) Security and system setup To enter the menu of each setting, follow the steps below: ■ Security setting items and operation procedure ● Setting or changing the PIN (Personal Identification Number)1. “Setup” → 2. “Security” → 3. “Set PIN” ● Lo...

333 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Setting or changing the PIN ■ Setting a PIN Select “Set PIN” by using a voice command or . Enter a PIN by using a voice command or . When using , input the code 1 digit at a time. ■ Changing the PIN Select “Set PIN” by u...

335 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Displaying the Bluetooth ® device address and name Select “Device Name” using . Turn to display the Bluetooth ® device address and name. Select “Go Back” using to return to “System Setup”. Initialization Select “Initiali...

337 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Using the phone book To enter the menu of each setting, follow the steps below: ● Adding a new phone number1. “Phonebook” → 2. “Add Entry” ● Setting speed dial1. “Phonebook” → 2. “Set Speed Dial (Speed Dial)” ● Changing ...

341 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Select the name to be registered by either of the followingmethods, and select “Confirm” by using a voice command or : a. Press the talk switch and say the desired name. b. Select “Record Name” by using , and say the des...

344 3-4. Using the hands-free system (for cellular phone) Deleting registered data Select “Delete Entry” by using a voice command or . Select the data to be deleted by either of the following meth-ods, and select “Confirm” by using a voice command or : a. Press the talk switch, and say the name of t...

345 3-4. Using the hands-free system (for cellular phone) 3 Inte rior fe atures Listing the registered data Selecting “List names” by using a voice command causes a list of theregistered data to be read aloud. When listing is complete, the system returns to “Phonebook”. Pressing the talk switch whil...

346 3-5. Using the interior lights Interior lights list Illuminated entry system: The various lights automatically turn on/ off according to the presence of the key, whether the doors are locked/unlocked, whether the doors are open/closed, and the “ENGINE START STOP” switch mode (vehicles with smart...

348 3-5. Using the interior lights Interior lights “ON” “OFF” “DOOR” The interior lights are turned on/off by the illuminated entry sys-tem. Personal lights Front ON/OFF Rear ON/OFF

349 3 Inte rior fe atures 3-6. Using the storage features List of storage features Overhead console Glove box Door pocket Cup holders Console boxes Coin tray Storage compartment

350 3-6. Using the storage features Glove box Open Lock with the mechanical keyor the master key Unlock with the mechanicalkey or the master key CAUTION ■ Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as thismay cause the foll...

351 3-6. Using the storage features 3 Inte rior fe atures Console boxes Front Lift the lid while pulling the lever. Rear Lift the lid while pulling the lever. CAUTION ■ While driving Keep the glove box closed.Injuries may result in the event of sudden braking, sudden swerving or anaccident.

353 3-6. Using the storage features 3 Inte rior fe atures Overhead console The overhead console is usefulfor temporarily storing sun-glasses and similar small items. CAUTION ■ While driving Do not leave the overhead console open. Items may fall out and causeinjury.

354 3-6. Using the storage features Storage compartment Front console Center console CAUTION ■ While driving Do not leave the storage compartment open. The opened compartment may hit your body or items may be thrown out ofthe compartment in the event of an accident or sudden braking and causeinjury.

355 3-6. Using the storage features 3 Inte rior fe atures Cup holders Front To open, press down andrelease the cup holder lid. Rear (type A) Pull down the armrest. Rear (type B) Pull down the armrest and openthe lid.

356 3-6. Using the storage features Door pockets The front door pocket can beopened and closed. CAUTION ■ Items unsuitable for the cup holder Do not place anything other than cups or aluminum cans in the cup holders.Other items may be thrown out of the holders in the event of an accident orsudden br...

357 3 Inte rior fe atures 3-7. Other interior features Sun visors Forward position: Flip down. Side position: Flip down,unhook, and swing to theside. Side extender: Place in sideposition, then slide back-wards.

358 3-7. Other interior features Vanity mirrors The light turns on when thecover is opened.To adjust the brightness of thelights, slide the switch.

359 3-7. Other interior features 3 Inte rior fe atures Clock ■ The clock is displayed when Vehicles with smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ONmode. Vehicles without smart key system The engine switch is in the “ACC” or “ON” position. ■ When the battery is dis...

360 3-7. Other interior features Ashtrays ∗ ∗ : If equipped CAUTION ■ When not in use Keep the ashtray closed.Injuries may result in the event of sudden braking, sudden swerving or anaccident. ■ To prevent fire ● Fully extinguish matches and cigarettes before putting them in the ashtray,then make su...

361 3-7. Other interior features 3 Inte rior fe atures Power outlets The power outlets can be used for 12V accessories that run on less than 10A. Front console box Center console box

362 3-7. Other interior features ■ The power outlets can be used when Vehicles with smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ONmode. Vehicles without smart key system The engine switch is in the “ACC” or “ON” position. NOTICE ■ To avoid damaging the power outlets C...

363 3-7. Other interior features 3 Inte rior fe atures Seat heaters/ventilators ∗ ∗ : If equipped The seat heaters and ventilators heat the seats and maintain good airflow by blowing air from the seats. Vehicles with ventilator Press the knob to release it,and turn the knob to thedesired temperature...

364 3-7. Other interior features ■ The seat heaters and ventilators can be used when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. CAUTION ■ Burns ● Use caution when seating the follo...

365 3-7. Other interior features 3 Inte rior fe atures Armrest NOTICE ■ To prevent damage to the armrest Do not place too much strain on the armrest. Pull the armrest down for use.

366 3-7. Other interior features Rear sunshade ∗ ∗ : If equipped ■ The rear sunshade can be used when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. ■ Reverse operation feature To ensu...

367 3-7. Other interior features 3 Inte rior fe atures ■ Operating the rear sunshade after turning the “ENGINE START STOP”switch or the engine switch off The rear sunshade can be raised and lowered for approximately 1 minute. ■ Customization that can be configured at Toyota dealer Contact your Toyot...

368 3-7. Other interior features Floor mats CAUTION Observe the following precautions. Failure to do so may cause the driver’s floor mat to slip, possibly interferingwith the pedals while driving. An unexpectedly high speed may result or itmay become difficult to stop the vehicle, leading to a serio...

370 3-7. Other interior features Trunk features ■ Shopping bag hooks ■ Storage box

371 3-7. Other interior features 3 Inte rior fe atures Trunk storage extension Pull down the rear seat centerarmrest. Open (push down the handle) CAUTION ■ While driving ● To avoid injury, always return the cargo hooks to their positions when theyare not in use. ● Always keep the trunk storage exten...

372 3-7. Other interior features Garage door opener ∗ The garage door opener (HomeLink ® Universal Transceiver) is manufac- tured under license from HomeLink ® . Programming the HomeLink ® (for U.S.A. owners) The HomeLink ® compatible transceiver in your vehicle has 3 buttons which can be programmed...

373 3-7. Other interior features 3 Inte rior fe atures ■ Programming the HomeLink ® Point the remote control for thedevice 1 to 3 in. (25 to 75 mm)from the HomeLink ® control but- tons. Keep the indicator light on theHomeLink ® in view while pro- gramming. Press and hold one of theHomeLink ® buttons...

374 3-7. Other interior features Test the operation of theHomeLink ® by pressing the newly programmed button. If programming a garage dooropener, check to see if the garagedoor opens and closes. If thegarage door does not operate,see if your garage transmitter isof the Rolling Code type. Pressand ho...

375 3-7. Other interior features 3 Inte rior fe atures ■ Programming a Rolling Code system (for U.S.A. owners) If your device is Rolling Code equipped, follow the steps under theheading “Programming the HomeLink ® ” before proceeding with the steps listed below. Locate the training button on the cei...

376 3-7. Other interior features ■ Programming an entry gate (for U.S.A. owners)/Programmingall devices in the Canadian market Place your transmitter 1 to 3 in. (25 to 75 mm) away from thesurface of the HomeLink ® . Keep the indicator light on the HomeLink ® in view while program- ming. Press and ho...

377 3-7. Other interior features 3 Inte rior fe atures Operating the HomeLink ® Press the appropriate HomeLink ® button. The HomeLink ® indicator light on the HomeLink ® transceiver should turn on. The HomeLink ® continues to send a signal for up to 20 seconds as long as the button is pressed. Repro...

378 3-7. Other interior features ■ Before programming ● Install a new battery in the transmitter. ● The battery side of the transmitter must be pointed away from theHomeLink ® . ■ Certification for the garage door opener For vehicles sold in U.S.A. FCC ID: NZLZTVHL4 NOTE:This device complies with Pa...

379 3-7. Other interior features 3 Inte rior fe atures CAUTION ■ When programming a garage door or other remote control device The garage door may operate, so ensure people and objects are out of dan-ger to prevent potential harm. ■ Conforming to federal safety standards Do not use the HomeLink ® Co...

380 3-7. Other interior features Compass ∗ ∗ : If equipped The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Operation Type A To turn the compass on or off,press the switch. Type B To turn the compass on or off,press the switch. ITN35A024

381 3-7. Other interior features 3 Inte rior fe atures Calibrating the compass The direction display deviates from the true direction determined bythe earth’s magnetic field. The amount of deviation varies accordingto the geographic position of the vehicle. If you cross over a map boundary shown in ...

382 3-7. Other interior features ■ Deviation calibration Stop the vehicle where it is safe to drive in a circle. Press the switch until a number(1 to 15) appears on the com-pass display. Press the switch, and referring to the map above, select thenumber of the zone where you are. Wait a few seconds ...

383 3-7. Other interior features 3 Inte rior fe atures ■ Conditions unfavorable to correct operation The compass may not show the correct direction in the following conditions: ● The vehicle is stopped immediately after turning. ● The vehicle is on an inclined surface. ● The vehicle is in a place wh...

384 3-7. Other interior features NOTICE ■ To avoid the compass malfunctions Do not place magnets or any metal objects near the inside rear view mirror. Doing this may cause a malfunction of the compass sensor. ■ To ensure normal operation of the compass ● Do not perform circling calibration of the c...

386 4-1. Maintenance and care Cleaning and protecting the vehicle exterior ■ Automatic car washes ● Fold the mirrors back before washing the vehicle. ● Brushes used in automatic car washes may scratch the vehicle surfaceand harm your vehicle’s paint. ■ High pressure car washes Do not allow the nozzl...

387 4-1. Maintenance and care 4 Mainten ance an d ca re CAUTION ■ When cleaning the windshield (vehicles equipped with the raindropdetection windshield wipers) Make sure to turn off the wiper switch. If the switch is left in the “AUTO” position, the windshield wiper may operateunexpectedly in the fo...

388 4-1. Maintenance and care NOTICE ■ To prevent paint deterioration and corrosion on the body and compo-nents (aluminum wheels etc.) ● Wash the vehicle immediately in the following cases: • After driving near the sea coast• After driving on salted roads• If you see coal tar or tree sap on the pain...

389 4-1. Maintenance and care 4 Mainten ance an d ca re Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle’s interior and keep it in top condition: ■ Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty sur-faces wi...

390 4-1. Maintenance and care ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a yearto maintain the quality of the vehicle’s interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use asponge or brush to apply...

391 4-1. Maintenance and care 4 Mainten ance an d ca re NOTICE ■ Cleaning detergents ● Do not use the following types of detergent, as they may discolor the vehi-cle interior or cause streaks or damage to painted surfaces. • Non-seat portions: Organic substances such as benzine or gasoline, alkaline...

392 4-2. Maintenance Maintenance requirements To ensure safe and economical driving, day-to-day care and regular maintenance is essential. It is the owner’s responsibility to perform regular checks. Toyota recommends the following maintenance. ■ General maintenance Should be performed on a daily bas...

393 4-2. Maintenance 4 Mainten ance an d ca re ■ Repair and replacement It is recommended that genuine Toyota parts be used for repair to ensureperformance of each system. If non-Toyota parts are used in replacement orif a repair shop other than a Toyota dealer performs repairs, confirm the war-rant...

394 4-2. Maintenance CAUTION ■ If your vehicle is not properly maintained It could result in serious damage to the vehicle and possible serious injury ordeath. ■ Hazardous materials ● Engine exhaust, some of its constituents, and a wide variety of automobilecomponents contain or emit chemicals known...

395 4-2. Maintenance 4 Mainten ance an d ca re General maintenance Engine compartment Items Check points Battery • Maintenance-free ( → P. 417) Brake fluid • At the correct level? ( → P. 414) Engine coolant • At the correct level? ( → P. 412) Engine oil • At the correct level? ( → P. 408) Exhaust sy...

396 4-2. Maintenance Vehicle interior Items Check points Accelerator pedal • Moves smoothly (without uneven pedal effort or catching)? Automatic transmission “Park” mechanism • Can the vehicle be hold securely on an incline with the shift lever in “P”? Brake pedal • Moves smoothly?• Does it have app...

397 4-2. Maintenance 4 Mainten ance an d ca re Vehicle exterior Items Check points Doors/trunk • Operate smoothly? Engine hood • The lock system works properly? Fluid leaks • Is there any leakage after parking? Tire • Inflation pressure is correct?• Tire surfaces not worn or damaged?• Tires rotated ...

398 4-2. Maintenance Emission inspection and maintenance (I/M) programs Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system moni- tors the operation of the emission control system. ■ If the malfunction indicator lamp comes on The OBD ...

399 4 Mainten ance an d ca re 4-3. Do-it-yourself maintenance Do-it-yourself service precautions If you perform maintenance yourself, be sure to follow the correct procedure given in these sections. Items Parts and tools Battery condition ( → P. 417) • Warm water• Baking soda• Grease• Conventional w...

400 4-3. Do-it-yourself maintenance Items Parts and tools Engine oil level ( → P. 408) • “Toyota Genuine Motor Oil” or equivalent • Rag or paper towel, funnel (used only for adding engine oil) Fuses ( → P. 444) • Fuse with same amperage rating as original Headlight aim ( → P. 453) • Phillips-head sc...

4 Mainten ance an d ca re 401 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that maymove suddenly, become hot, or become electrically energized. To avoid deathor serious injury, observe the following precautions. ■ When working on the engine compa...

402 4-3. Do-it-yourself maintenance CAUTION ■ When working near the electric cooling fan or radiator grille Vehicles with smart key system Be sure the “ENGINE START STOP” switch is turned OFF. With the“ENGINE START STOP” switch in IGNITION ON mode, the electric coolingfan may automatically start to ...

403 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Hood CAUTION ■ Pre-driving check Check that the hood is fully closed and locked. If the hood is not locked properly it may open while the vehicle is in motionand cause an accident, which may result in death or serious injury. Release the ...

404 4-3. Do-it-yourself maintenance Positioning a floor jack When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury. Front Rear

4 Mainten ance an d ca re 405 4-3. Do-it-yourself maintenance CAUTION ■ When raising your vehicle Make sure to observe the following to reduce the possibility of death or seri-ous injury. ● When using a floor jack, follow the instructions of the manual provided withthe jack. ● Do not use the jack th...

4 Mainten ance an d ca re 407 4-3. Do-it-yourself maintenance Engine compartment cover ■ Removing the cover ■ Installing the clips Open Insert Press NOTICE ■ After installing an engine compartment cover Make sure that the cover is securely installed in its original position.

408 4-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oillevel on the dipstick. ■ Checking the engine oil Park the vehicle on level ground. After turning off the engine,wait more than five minutes for the oil to drain back into thebottom of...

4 Mainten ance an d ca re 409 4-3. Do-it-yourself maintenance ■ Adding engine oil If the oil level is below or nearthe low level mark, add engineoil of the same type as already inthe engine. Make sure to check the oil type and prepare the items needed beforeadding oil. Remove the oil filler cap. Add...

410 4-3. Do-it-yourself maintenance ■ Engine oil consumption ● The amount of engine oil consumed depends on the oil viscosity, thequality of the oil and the way the vehicle is driven. ● More oil is consumed under driving conditions such as high speeds, fre-quent acceleration and deceleration. ● A ne...

4 Mainten ance an d ca re 411 4-3. Do-it-yourself maintenance CAUTION ■ Used engine oil ● Used engine oil contains potentially harmful contaminants which maycause skin disorders such as inflammation or skin cancer, so care shouldbe taken to avoid prolonged and repeated contact. To remove used engine...

412 4-3. Do-it-yourself maintenance Engine coolant The coolant level is satisfactory if it is between the “F” and “L” lines onthe reservoir when the engine is cold. Reservoir cap Full Low If the level is on or below the “L”line, add coolant up to the “F” line. ■ If the coolant level drops within a s...

4 Mainten ance an d ca re 413 4-3. Do-it-yourself maintenance Radiator and condenser Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure oftheir condition, have your vehicle checked by your Toyota dealer. CAUTION ■ When...

414 4-3. Do-it-yourself maintenance Brake fluid ■ Checking fluid level The brake fluid level should bebetween the “MAX” and “MIN”lines on the tank. Make sure to check the fluid type and prepare the necessary items. ■ Adding fluid Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Items Clean fun...

4 Mainten ance an d ca re 415 4-3. Do-it-yourself maintenance Power steering fluid ■ Fluid level The fluid level should be within the appropriate range. Full (when hot) Add fluid (when hot) Full (when cold) Add fluid (when cold) Hot: The vehicles has been driven around 50 mph (80 km/h) for 20 minute...

416 4-3. Do-it-yourself maintenance ■ Checking the fluid level Make sure to check the fluid type and prepare the necessary items. Clean all dirt off the reservoir. Remove the cap by turning it counterclockwise. Wipe the dipstick clean. Reinstall and remove the reservoir cap again. Check the fluid le...

4 Mainten ance an d ca re 417 4-3. Do-it-yourself maintenance Battery Check the battery as follows. ■ Battery exterior Make sure that the battery terminals are not corroded and thatthere are no loose connections, cracks, or loose clamps. Terminals Hold-down clamp ■ Before recharging When recharging,...

418 4-3. Do-it-yourself maintenance CAUTION ■ Chemicals in the battery A battery contains poisonous and corrosive sulfuric acid and may producehydrogen gas which is flammable and explosive. To reduce the risk of deathor serious injury, take the following precautions while working on or near bat-tery...

4 Mainten ance an d ca re 419 4-3. Do-it-yourself maintenance CAUTION ■ Emergency measures regarding electrolyte ● If electrolyte gets in your eyesFlush your eyes with clean water for at least 15 minutes and get immedi-ate medical attention. If possible, continue to apply water with a sponge orcloth...

420 4-3. Do-it-yourself maintenance Washer fluid If any washer does not work orthe low washer fluid warning lightcomes on, the washer tank maybe empty. Add washer fluid. CAUTION ■ When refilling the washer fluid Do not refill the washer fluid when the engine is hot or running, as thewasher fluid con...

421 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Tires Replace or rotate tires in accordance with maintenance sched- ules and treadwear. ■ Checking tires New tread Treadwear indicator Worn tread The location of treadwearindicators is shown by the“TWI” or “ ∆ ” marks, etc., molded on the...

422 4-3. Do-it-yourself maintenance Installing tire pressure warning valves and transmitters When replacing tires or wheels, tire pressure warning valves andtransmitters must also be installed. When new tire pressure warning valves and transmitters areinstalled, new tire pressure warning valve and t...

4 Mainten ance an d ca re 423 4-3. Do-it-yourself maintenance ■ How to initialize the tire pressure warning system Park the vehicle in safe place and turn the “ENGINE STARTSTOP” switch or the engine switch OFF. While the vehicle is moving, initialization is not performed. Adjust the tire inflation p...

424 4-3. Do-it-yourself maintenance Registering ID codes The tire pressure warning valve and transmitter is equipped with aunique ID code. When replacing a tire pressure warning valve and transmitter, it isnecessary to register the ID code of tire pressure warning valve andtransmitter. Have the ID c...

4 Mainten ance an d ca re 425 4-3. Do-it-yourself maintenance ■ Tire life Any tire over 6 years old must be checked by a qualified technician evenif they have seldom or never been used or damage is not obvious. ■ If the tread wears down below 0.16 in. (4 mm) on snow tires The effectiveness of snow t...

426 4-3. Do-it-yourself maintenance ■ Tire types 1 Summer tires Summer tires are high-speed performance tires best suited to highwaydriving under dry conditions. Since summer tires do not have the sametraction performance as snow tires, summer tires are inadequate fordriving on snow-covered or icy r...

4 Mainten ance an d ca re 427 4-3. Do-it-yourself maintenance ■ When initialization of the tire pressure warning system has failed Initialization can be completed in a few minutes. However, in the follow-ing cases, the settings have not been recorded and the system will notoperate properly. If repea...

428 4-3. Do-it-yourself maintenance CAUTION ■ Tire pressure warning system operation The tire pressure warning system may not provide warning immediatelyif a tire bursts or if sudden air leakage occurs. ■ When inspecting or replacing tires Observe the following precautions to prevent accidents. Fail...

4 Mainten ance an d ca re 429 4-3. Do-it-yourself maintenance NOTICE ■ Repairing or replacing tires, wheels, tire pressure warning valves,transmitters and tire valve caps ● When removing or fitting the wheels, tires or the tire pressure warningvalve and transmitter, contact your Toyota dealer as the...

430 4-3. Do-it-yourself maintenance Tire inflation pressure ■ Tire inflation pressure The recommended cold tire inflation pressure and tire size is dis-played on the tire and loading information label. ( → P. 526)

4 Mainten ance an d ca re 431 4-3. Do-it-yourself maintenance ■ Inspection and adjustment procedure Tire valve Tire pressure gauge Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the graduations of the gauge. If the tire inflation pres...

432 4-3. Do-it-yourself maintenance . ■ Tire inflation pressure check interval You should check tire inflation pressure every two weeks, or at leastonce a month.Do not forget to check the spare. ■ Effects of incorrect tire inflation pressure Driving with incorrect tire inflation pressure may result ...

4 Mainten ance an d ca re 433 4-3. Do-it-yourself maintenance CAUTION ■ Proper inflation is critical to save tire performance Keep your tires properly inflated. Otherwise, the following conditionsmay occur and result in an accident causing death or serious injury. ● Excessive wear ● Uneven wear ● Po...

434 4-3. Do-it-yourself maintenance Wheels If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause loss of handling control. ■ Wheel selection When replacing wheels, care should be taken to ensure thatthey are equivalent to tho...

4 Mainten ance an d ca re 435 4-3. Do-it-yourself maintenance ■ When replacing wheels The wheels of your Toyota are equipped with tire pressure warningvalves and transmitters that allow the tire pressure warning system toprovide advanced warning in the event of a loss in tire inflation pressure.When...

436 4-3. Do-it-yourself maintenance NOTICE ■ Replacing tire pressure warning valves and transmitters ● Because tire repair or replacement may affect the tire pressure warn-ing valves and transmitters, make sure to have tires serviced by yourToyota dealer or other qualified service shop. In addition,...

437 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. ■ Removal method Set the air conditioning system to recirculated mode. The air conditioning filter case cannot be remov...

4 Mainten ance an d ca re 439 4-3. Do-it-yourself maintenance ■ Checking interval Inspect and replace the air conditioning filter according to the maintenanceschedule. In dusty areas or areas with heavy traffic flow, early replacementmay be required. (For scheduled maintenance information, refer to ...

440 4-3. Do-it-yourself maintenance Key battery Replace the battery with a new one if it is discharged. ■ You will need the following items: ● Flathead screwdriver (To prevent damage to the key, coverthe tip of the screwdriver with rag.) ● Small Phillips-head screwdriver ● Lithium battery CR1632 (ve...

4 Mainten ance an d ca re 441 4-3. Do-it-yourself maintenance Remove the depleted battery. Insert a new battery with the“+” terminal facing up. ■ Replacing the battery (vehicles without smart key system) Remove the cover. Remove the module. STEP 3 STEP 1 STEP 2

442 4-3. Do-it-yourself maintenance ■ If the key battery is discharged The following symptoms may occur. ● The smart key system and wireless remote control will not function prop-erly. ● The operational range is reduced. ■ Use a CR1632 (vehicles with smart key system), or CR2016 (vehicleswithout sma...

4 Mainten ance an d ca re 443 4-3. Do-it-yourself maintenance NOTICE ■ For normal operation after replacing the battery Observe the following precautions to prevent accidents. ● Always work with dry hands.Moisture may cause the battery to rust. ● Do not touch or move any other components inside the ...

444 4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Turn the “ENGINE START STOP” switch or the engineswitch OFF. Open the fuse box cover. Engine compartm...

4 Mainten ance an d ca re 449 4-3. Do-it-yourself maintenance ■ Driver’s side instrument panel Fuse Ampere Circuit 1 RR DOOR 20 A Power window 2 RL DOOR 20 A Power window 3 FR DOOR 20 A Power window, driving position memory system 4 FOG 15 A Front fog lights 5 OBD 7.5 A On-board diagnosis system 6 M...

452 4-3. Do-it-yourself maintenance ■ After a fuse is replaced ● If the lights do not turn on even after the fuse has been replaced, a bulbmay need replacement. ( → P. 455) ● If the replaced fuse blows again, have the vehicle inspected by yourToyota dealer. ■ If there is an overload in the circuits ...

453 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Headlight aim (with discharge headlights) ■ Vertical movement bolts Adjustment bolt A Adjustment bolt B ■ Before checking the headlight aim Make sure the vehicle has a full tank of gas and the areaaround the headlight is not deformed. Par...

454 4-3. Do-it-yourself maintenance ■ Adjusting the headlight aim Turn bolt A in either directionusing a Phillips-head screw-driver. Remember the turning direc-tion and the number of turns. Turn bolt B the same numberof turns and in the same direc-tion as step 1 using a Phillips-head screwdriver. If...

455 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Light bulbs You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about r...

4 Mainten ance an d ca re 457 4-3. Do-it-yourself maintenance Exchange the light bulb, andinstall the socket. Align the 3 tabs on the light bulbwith the mounting, and insert. Turn and secure the socket. After installing the socket, turn theheadlight low beams on once andvisually confirm that no ligh...

460 4-3. Do-it-yourself maintenance Exchange the light bulb, andinstall the socket. Align the 3 tabs on the light bulbwith the mounting, and insert. Turn and secure the socket. After installing the socket, turn theheadlight high beams on onceand visually confirm that no lightis leaking through the m...

462 4-3. Do-it-yourself maintenance Turn and secure the socket andplug the connector. After installing the socket, turn thefog lights on once and visuallyconfirm that no light is leakingthrough the mounting. ■ Front turn signal/parking lights Remove the fender liner clip. Partly remove the fender li...

4 Mainten ance an d ca re 463 4-3. Do-it-yourself maintenance Remove the light bulb. ■ Front side marker lights Remove the fender liner clip. Partly remove the fender linerand turn the bulb base counter-clockwise. STEP 3 STEP 1 STEP 2

464 4-3. Do-it-yourself maintenance Remove the light bulb. ■ Auxiliary lights Turn the bulb base counterclock-wise. Remove the light bulb. STEP 3 STEP 1 STEP 2

4 Mainten ance an d ca re 465 4-3. Do-it-yourself maintenance ■ Rear turn signal lights, stop lights and rear side marker lights Open the trunk and remove thecover as follows. Turn the bulb bases counter-clockwise and remove (upperand lower), or squeeze bulbbase and remove (center). Remove the light...

4 Mainten ance an d ca re 467 4-3. Do-it-yourself maintenance ■ License plate light Remove the cover. To prevent damaging the vehicle,wrap the flathead screwdriverwith a tape. Remove the light bulb. STEP 1 STEP 2

468 4-3. Do-it-yourself maintenance ■ Bulbs other than the above If any of the bulbs listed below has burnt out, have your Toyotadealer replace it. ● Headlights (discharge bulb) ● Side turn signal lights ● Tail lights ● High mounted stoplight ■ Condensation build-up on the inside of the lens Contact...

4 Mainten ance an d ca re 469 4-3. Do-it-yourself maintenance CAUTION ■ Replacing light bulbs ● Turn off the headlights. Do not attempt to replace the bulb immediatelyafter turning off the headlights. The bulbs become very hot and may cause burns. ● Do not touch the glass portion of the light bulb w...

470 4-3. Do-it-yourself maintenance CAUTION ■ High-intensity discharge (HID) headlights (if equipped) ● Contact your Toyota dealer before replacing high-intensity dischargeheadlights (including light bulbs). ● Do not touch the high-intensity discharge headlight’s high voltage socketwhen the headligh...

472 5-1. Essential information Emergency flashers NOTICE ■ To prevent battery discharge Do not leave the emergency flashers on longer than necessary when theengine is not running. Use the emergency flashers if the vehicle malfunctions or is involved in an accident. Press the switch to flash allthe t...

5 Wh en t ro uble ar ises 473 5-1. Essential information If your vehicle needs to be towed Before towing The following may indicate a problem with your transmission. Contactyour Toyota dealer before towing. ● The engine is running, but the vehicle will not move. ● The vehicle makes an abnormal sound...

474 5-1. Essential information Towing with a sling-type truck NOTICE ■ To prevent body damage Do not tow with a sling-type truck, either from the front or rear.

5 Wh en t ro uble ar ises 475 5-1. Essential information Towing with a wheel lift-type truck From front Release the parking brake. From rear Use a towing dolly under thefront wheel. NOTICE ■ To prevent causing damage to the transmission Never tow this vehicle from the rear with the front wheel on th...

476 5-1. Essential information Using a flat bed truck If you use chains or cables to tiedown your vehicle, the anglesshaded in black must be 45°. Do not overly tighten the tiedowns or the vehicle may bedamaged.

5 Wh en t ro uble ar ises 477 5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms ● Fluid leaks under the vehicle(Water dripping fr...

478 5-1. Essential information Fuel pump shut off system Follow the procedure below to restart the engine after the system isactivated. Vehicles with smart key system: Turn the “ENGINE STARTSTOP” switch OFF. Vehicles without smart key system: Turn the engine switch tothe “ACC” or “LOCK” position. Re...

5 Wh en t ro uble ar ises 479 5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer sounds... Stop the vehicle immediately. Continuing to drive the vehiclemay be dangerous. The following warning indicates a possible problem in the brake sys-tem. Immediately stop the vehi...

480 5-2. Steps to take in an emergency Stop the vehicle immediately. The following warning indicates the possibility of damage to the vehi-cle that may lead to an accident. Immediately stop the vehicle in asafe place and contact your Toyota dealer. Have the vehicle inspected immediately. Failing to ...

5 Wh en t ro uble ar ises 481 5-2. Steps to take in an emergency Have the malfunction repaired immediately. After taking the specified steps to correct the suspected problem,check that the warning light turns off. Warning light Warning light/Details SRS warning light Malfunction in:• The SRS airbag ...

5 Wh en t ro uble ar ises 487 5-2. Steps to take in an emergency ■ If the tire pressure warning system is inoperative The tire pressure warning system will be disabled in the following condi-tions: (When the condition becomes normal, the system will work properly.) ● If tires not equipped with tire ...

488 5-2. Steps to take in an emergency ■ If the tire pressure warning light frequently comes on after blinkingfor 1 minute Vehicles without smart key system If the tire pressure warning light comes on after blinking for 1 minute fre-quently when the engine switch is turned to the “ON” position, have...

5 Wh en t ro uble ar ises 489 5-2. Steps to take in an emergency CAUTION ■ If the tire pressure warning light comes on Be sure to observe the following precautions. Failure to do so couldcause loss of vehicle control and result in death or serious injury. ● Stop your vehicle in a safe place as soon ...

490 5-2. Steps to take in an emergency CAUTION Please note that the TPMS (tire pressure warning system) is not a sub-stitute for proper tire maintenance, and it is the driver’s responsibility tomaintain correct tire pressure, even if under-inflation has not reached thelevel to trigger illumination o...

5 Wh en t ro uble ar ises 491 5-2. Steps to take in an emergency If you have a flat tire Remove the flat tire and replace it with the spare provided. ■ Before jacking up the vehicle ● Stop the vehicle on a hard, flat surface. ● Set the parking brake. ● Shift the shift lever to “P”. ● Stop the engine...

492 5-2. Steps to take in an emergency Take out the jack Remove the cover. To remove the jack, turn the jackjoint by hand until the jackbecomes free. Taking out the spare tire Remove the luggage floor cover. STEP 1 STEP 2 STEP 1

5 Wh en t ro uble ar ises 493 5-2. Steps to take in an emergency Loosen the center fastener thatsecures the spare tire. Remove the spare tire cover. Replacing a flat tire Chock the tires. STEP 2 STEP 3 STEP 1 Flat tire Wheel chock positions Front Left-hand side Behind the rear right-hand side tire R...

496 5-2. Steps to take in an emergency Installing the spare tire Remove any dirt or foreign mat-ter from the wheel contact sur-face. If foreign matter is on the wheelcontact surface, the wheel nutsmay loosen while the vehicle isin motion, and the tire maycome off the vehicle. Install the spare tire ...

5 Wh en t ro uble ar ises 497 5-2. Steps to take in an emergency Firmly tighten each nut two orthree times in the order shown inthe illustration. Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m) Reinstall the wheel ornament. Stow the flat tire, tire jack and all tools. STEP 4 STEP 5 ■ To store the...

498 5-2. Steps to take in an emergency CAUTION ■ Using the tire jack Improper use of the tire jack may lead to death or injuries due to thevehicle suddenly falling off the jack. ● Do not use the tire jack for any purpose other than replacing tires orinstalling and removing tire chains. ● Only use th...

500 5-2. Steps to take in an emergency NOTICE ■ Do not drive the vehicle with a flat tire Do not continue driving with a flat tire.Driving even a short distance with a flat tire can damage the tire and thewheel beyond repair. ■ When replacing the tires When removing or fitting the wheels, tires or t...

5 Wh en t ro uble ar ises 501 5-2. Steps to take in an emergency If the engine will not start If the engine will not start even though correct starting procedures are being followed ( → P. 154, P. 158), consider each of the following points. ■ The engine will not start even when the starter motor op...

502 5-2. Steps to take in an emergency Emergency start function (vehicles with smart key system) When the engine does not start, the following steps can be used asan interim measure to start the engine if the “ENGINE START STOP”switch is functioning normally. Set the parking brake. Shift the shift l...

5 Wh en t ro uble ar ises 503 5-2. Steps to take in an emergency If the shift lever cannot be shifted from P If the shift lever cannot be shifted with your foot on the brake, there may be a problem with the shift lock system (a system to prevent accidental operation of the shift lever). Have the veh...

504 5-2. Steps to take in an emergency If you lose your keys New genuine keys can be made by your Toyota dealer. Bring the other key and the key number stamped on the key number plate.

5 Wh en t ro uble ar ises 505 5-2. Steps to take in an emergency If the electronic key does not operate properly (with smart key system) Locking and unlocking the doors key linked functions Using the mechanical key ( → P. 28) in order to perform the following operations: Locks all doors Unlocks the ...

506 5-2. Steps to take in an emergency Changing “ENGINE START STOP” switch modes and starting theengine Put the shift lever in “P” and apply the brakes. Touch the Toyota emblem side ofthe electronic key to the“ENGINE START STOP” switch. An alarm will sound to indicatethat the start function cannotde...

508 5-2. Steps to take in an emergency If the vehicle battery is discharged The following procedures may be used to start the engine if the vehi- cle’s battery is discharged. You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi-c...

510 5-2. Steps to take in an emergency ■ Starting the engine when the battery is discharged The engine cannot be started by push-starting. ■ To prevent battery discharge ● Turn off the headlights and the audio system while the “ENGINE STARTSTOP” switch or the engine is turned off. ● Turn off any unn...

5 Wh en t ro uble ar ises 511 5-2. Steps to take in an emergency CAUTION ■ Battery precautions The battery contains poisonous and corrosive acidic electrolyte, whilerelated parts contain lead and lead compounds. Observe the following pre-cautions when handling the battery: ● When working with the ba...

512 5-2. Steps to take in an emergency If your vehicle overheats If your engine overheats: Stop the vehicle in a safe place and turn off the air condi-tioning system. Check to see if steam is coming out from under the hood. If you see steam: Stop the engine. Carefully lift the hood after the steamsu...

5 Wh en t ro uble ar ises 513 5-2. Steps to take in an emergency ■ Overheating In the following situations, your vehicle may be overheating. ● The engine coolant temperature gauge enters the red zone or a loss ofpower is experienced. ● Steam is coming from under the hood. Add coolant if required. Wa...

514 5-2. Steps to take in an emergency CAUTION ■ To prevent an accident or injury when inspecting under the hood ofyour vehicle ● If steam is seen coming from under the hood, do not open the hood untilthe steam has subsided. The engine compartment may be very hot, caus-ing serious injury such as bur...

5 Wh en t ro uble ar ises 515 5-2. Steps to take in an emergency If the vehicle becomes stuck CAUTION ■ When attempting to free a stuck vehicle If you choose to rock the vehicle back and forth to free it, make sure the sur-rounding area is clear, to avoid striking other vehicles, objects or persons....

516 5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following pro- cedure: Steadily step on the brake pedal with both feet and firmlydepress i...

5 Wh en t ro uble ar ises 517 5-2. Steps to take in an emergency CAUTION ■ If the engine has to be turned off while driving ● Power assist for the brakes and steering wheel will be lost, making thebrake pedal harder to depress and the steering wheel heavier to turn.Decelerate as much as possible bef...

520 6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions and weight * : Unladen vehicle Overall length 197.6 in. (5020 mm) Overall width 72.8 in. (1850 mm) Overall height * 58.5 in. (1485 mm) Wheelbase 111.0 in. (2820 mm) Tread Front 62.2 in. (1580 mm) Rear 61.6 in. (1565 mm) Vehi...

521 6-1. Specifications 6 Vehicl e sp ecification s Vehicle identification The vehicle identification number (VIN) is the legal identifier for yourvehicle. This is the primary identification number for your Toyota. It isused in registering the ownership of your vehicle. This number is stamped on the...

523 6-1. Specifications 6 Vehicl e sp ecification s Oil grade: ILSAC multigrade engine oil Recommended viscosity: SAE 5W-30 SAE 5W-30 is the best choice forgood fuel economy and goodstarting in cold weather. If SAE 5W-30 is not available,SAE 10W-30 oil may be used.However, it should be replacedwith ...

524 6-1. Specifications Cooling system Ignition system Electrical system Capacity 8.8 qt. (8.3 L, 7.3 lmp.qt.) Coolant type Use either of the following: • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non- silicate, non-amine, non-nitrite, and non-borate coolant with ...

525 6-1. Specifications 6 Vehicl e sp ecification s Automatic transaxle * : The fluid capacity is the quantity of reference. If replacement is necessary, contact your Toyota dealer. Brakes * 1 : Minimum pedal clearance when depressed with a force of 110 lbf (490 N, 50 kgf) while the engine is runnin...

526 6-1. Specifications Steering Tires and wheels Type A Type B Free play Less than 1.2 in. (30 mm) Tire size P215/55R17 93V Front and rear tire inflation pressure (Recommended cold tire inflation pressure) Vehicle speed psi (kPa, kgf/cm 2 or bar) More than 99 mph (160 km/h) 38 (260, 2.6) 99 mph (16...

528 6-1. Specifications Fuel information ■ Fuel tank opening for unleaded gasoline To help prevent incorrect fueling, your Toyota has a fuel tank opening thatonly accommodates the special nozzle on unleaded fuel pumps. ■ If your engine knocks ● Consult your Toyota dealer. ● You may occasionally noti...

529 6-1. Specifications 6 Vehicl e sp ecification s ■ Gasoline quality standards ● Automotive manufacturers in the US, Europe and Japan have developeda specification for fuel quality called World-Wide Fuel Charter (WWFC)that is expected to be applied worldwide. ● The WWFC consists of four categories...

531 6-1. Specifications 6 Vehicl e sp ecification s NOTICE ■ Notice on fuel quality ● Do not use improper fuels. If improper fuels are used the engine will bedamaged. ● Do not use leaded gasoline.Leaded gasoline can cause damage to your vehicle’s three-way catalyticconverters causing the emission co...

532 6-1. Specifications Tire information Typical tire symbols Tire size ( → P. 534) DOT and Tire Identification Number (TIN) ( → P. 533) Location of treadwear indicators ( → P. 421) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Tire ply composition and ma...

533 6-1. Specifications 6 Vehicl e sp ecification s Typical DOT and tire identification number (TIN) DOT symbol * Tire Identification Number(TIN) Tire manufacturer’s identifica-tion mark Tire size code Manufacturer’s optional tiretype code (3 or 4 letters) Manufacturing week Manufacturing year * : T...

534 6-1. Specifications Tire size ■ Typical tire size information The illustration indicates typicaltire size. Tire use(P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio(tire height to section width) Tire construction code(R = Radial, D = Diagonal) Wheel diameter (inches...

535 6-1. Specifications 6 Vehicl e sp ecification s Tire section names Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer Uniform Tire Quality Grading This information has been prepared in accordance with regulationsissued by the National Highway Tra...

536 6-1. Specifications ■ DOT quality grades All passenger vehicle tires must conform to Federal SafetyRequirements in addition to these grades. Quality grades can befound where applicable on the tire sidewall between tread shoulderand maximum section width. For example: Treadwear 200 Traction AA Te...

538 6-1. Specifications Glossary of tire terminology Tire related term Meaning Cold tire inflation pressure Tire pressure when the vehicle has been parked for three hours or more, or has not been driven more than 1 mile or 1.5 km under that condition Maximum inflation pressure The maximum cold infla...

543 6-1. Specifications 6 Vehicl e sp ecification s * : Table 1 ⎯ Occupant loading and distribution for vehicle normal load for various designated seating capacities Tire related term Meaning Sidewall That portion of a tire between the tread and bead Sidewall separation The parting of the rubber com...

545 6 Vehicl e sp ecification s 6-2. Customization Customizable features Item Function Default setting Customized setting Smart key system ( → P. 30) Smart key system ON OFF Operation signal(Emergency flashers) ON OFF Operation signal(Buzzer) ON OFF Wireless remote control ( → P. 42) Unlocking opera...

547 6-2. Customization 6 Vehicl e sp ecification s * : Vehicles sold outside Canada Item Function Default setting Customized setting Door lock ( → P. 47) Unlocking using a key Driver’s door unlocked in 1-step, all doors unlocked in 2-step All doors unlocked in 1-step Speed-detecting auto-matic door ...

549 6 Vehicl e sp ecification s 6-3. Initialization Items to initialize Item When to initialize Reference Power window • After reconnecting or changing the battery • After changing a fuse P. 86 Moon roof P. 90 Maintenance data After the maintenance is performed P. 410 Tire pressure warning system • ...

553 7 For owners Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions inEnglish.

556 SRS airbag instructions for Canadian owners (in French)

568 Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING A/C Air Conditioning ABS Anti-lock Brake System ACC Accessory ALR Automatic Locking Retractor CRS Child Restraint System ECU Electronic Control Unit EDR Event Data Recorder ELR Emergency Locking Retractor GAWR Gross Axle Weight Ra...

577 What to do if... The warning light or indicator light comes on P. 479 If the warning light turns on ■ Warning lights or or P. 479 P. 480 P. 482 or P. 481 P. 482 P. 482 P. 482 P. 481 P. 481 P. 481 P. 480 P. 480 P. 483 P. 481 P. 483 Brake system warning light Malfunction indicator lamp ABS warning...

580 GAS STATION INFORMATION Auxiliary catch lever P. 403 Trunk opener P. 54 Fuel filler door P. 92 Hood lock release lever P. 403 Fuel filler door opener P. 92 Tire inflation pressure P. 526 Fuel tank capacity(Reference) 18.5 gal. (70 L, 15.4 lmp.gal.) Fuel type Unleaded gasoline only P. 92, 522 Col...