Toyota 2011 Sienna- Manuals

4 OVERVIEW Low engine oil pressure warning 1,2 Driver seat belt reminder 2 (alarm will sound if speed is over 12 mph)Front passenger seat belt reminder 2 (alarm will sound if speed is over 12 mph) Brake system warning 1,2 Charging system warning 1,2 Malfunction/Check Engine indicator 1,2 Indicator s...

6 OVERVIEW Keyless entry Locking operation NOTE: If a door is not opened within 60 seconds of unlocking, all doors will relock for safety. Push Push ONCE: Driver door TWICE: ALL doors Unlocking operation Panic button Push and hold Power back door operation (if equipped) Push and hold Type A Type B T...

7 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES Smart Key system (if equipped) Start function Accessories such as the radio will operate. Power ON; the engine not running. All systems OFF. ACCESSORY ON OFF NOTE: Gear shift lever must be in Park and brake pedal depressed. Push Depr...

8 Fuel tank door release and cap Pull up Store Turn NOTE: Tighten until one click is heard. If the cap is not tightenedenough, Check Engine “ ” indicator may illuminate. Hood release Pull up latch and raise hood Pull OVERVIEW Insert rod to hold hood open

10 FEATURES/OPERATIONS Auto lock functions Automatic door locks can be programmed to operate in four differentmodes, or turned OFF. - Doors lock when shifting from Park. - Doors lock when the vehicle speed goes above approximately 12 mph. - Doors unlock when shifting into Park. - Doors unlock when t...

11 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES Hold wheel, push lever down, set angle and length, and return lever. NOTE: Do not attempt to adjust while the vehicle is in motion. Tilt and telescopic steering wheel Length Lock release lever Angle Lights & turn signals Headlig...

12 FEATURES/OPERATIONS Headlight beam level control (if equipped) Rotating the dial downward will lower the angle of the beam. Up Down Down Up Turn signals Front fog lights (if equipped) Front fog lights come on only whenthe headlights are on low beam. Right turn Lane change Lane change Left turn Tu...

13 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES Windshield wipers & washers Interval wipe Slow Fast Pull to wash and wipe Single wipe Adjust frequency* Front Rear Wash and wipe Wipe Interval wipe Wash and wipe * Intermittent windshield wiper frequency adjustment Rotate to inc...

14 FEATURES/OPERATIONS Seat adjustments-Rear Second row seat Third row seat Seat position (forward/backward)Seatback angleOttoman angle Refer to the Owner’s Manual for more details. Tip-up seat Manual Ottoman seat Power Seat adjustments-Front Manual seat Power seat Seat position (forward/backward)He...

15 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES (2) (2) (1) (1) Tip-up seats Fold Pull Lift Pull Pull Tip-up Pull Fold Lift Ottoman seats Seats-Removing second row center seat (if equipped) Pull Fold Pull Remove (2) (1) (3) Seats-Removing second row outside seats

16 FEATURES/OPERATIONS Seats-Stowing third row seats (manual) Lower An alarm will sound for 10 seconds and the indicator will light up on the instrument panel if the seat is not fully open or stowed whenvehicle is shifted out of Park. Refer to the Owner’s Manual for more details. Third seat foldinco...

17 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES Opening/Closing ON/OFF switch Power • Sliding doors will not fully open if the sliding door window is open.• Power sliding doors will open only when gear selector is in the “P” (Park) position, and doors are unlocked. Refer to the O...

18 FEATURES/OPERATIONS Windows Automatic operation Push the switch completely down or pull it completely up and release to fully open or close. To stop window midway,lightly push the switch in the opposite direction. Window lock switch Deactivates all passenger windows. Driver’s window remains opera...

19 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES Moonroof (if equipped) Rear moonroof (if equipped) Front moonroof Close Close Open Open Sunshade-Side (if equipped) Rear side window Rear quarter window Hook Pull Hook Pull Clock (if equipped) H- Hour set M- Minute set Open* Close C...

20 To set, cancel and resume a speed Refer to “Functions” in the Cruise Control section, and to the Owner’s Manual for more details. Fixed speed mode (1) Push System ON/OFF (2) Push and hold Refer to the Owner’s Manual for more details and complete safety precautions before attempting to use “Dynami...

21 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES Distance control mode To set, cancel and resume a speed Refer to “Functions” in the Cruise Control section, and your Owner’s Manual for more details. NOTE: Once vehicle speed is set, pushing lever up toward “+ RES” will increase spe...

22 FEATURES/OPERATIONS Audio CD PLAYER To scan tracks on a disc Push and hold “SCAN.” Push again to hold selection. CD changer (Type 2 only)-To load one disc Push “LOAD” and insert one disc. -To load multiple discs Push and hold “LOAD” until you hear a beep. Insert one disc. Shutter will close and t...

23 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES “MODE” Push to turn audio ON and select an audio mode. Push and hold to turnthe audio system OFF. “ ” Use to search within the selected audio medium (radio, CD, iPod, etc.). > > Steering wheel switches (if equipped) Volume con...

24 Air Conditioning/Heating Front automatic Air Conditioning FEATURES/OPERATIONS Automatic climate control ONAdjusting the temperature setting will cause the airflow vents, airintake and fan to adjust automatically.Temperature selector (driver side)Airflow ventIn “ ” mode, use fresh air (“ ” indicat...

25 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES Front manual Air Conditioning Temperature selector (driver side)Airflow ventIn “ ” mode, use fresh air (“ ” indicator OFF) to reduce window fogging. “ ” mode uses fresh air only. Front fan speedTemperature selector (rear passenger a...

26 FEATURES/OPERATIONS Seat heaters (if equipped) Frontpassenger’s seat Driver’s seat Rear manual Air Conditioning Fan speedAirflow ventTemperature selector

27 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES Bluetooth ® technology allows dialing or receipt of calls without taking hands from the steering wheel or using a cable to connect the telephoneand the system. Refer to “Using the hands-free phone system (for cellular phone),” Secti...

28 FEATURES/OPERATIONS The Enhanced VSC OFF button is used to switch between modes related tothe TRAC and Enhanced VSC functions. Refer to Section 2-4 of the Owner’s Manual for more information. Enhanced VSCOFF button Enhanced VSC OFF button Front audioDVD playerDisplayHeadphone jacks and headphone ...

29 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES HAC helps prevent rolling backwards on an incline. To engage, push further down on brake pedal while at a complete stop until a beep sounds and slip indicator illuminates. HAC holds for approximately 2 seconds after releasing brake ...

31 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES Cup holders Instrument panel Second center seat Third row area Console box Front side Rear side Type A Type B Bottle holders NOTE : Do not place open containers in the bottle holders. Front doors Sliding doors

32 SAFETY AND EMERGENCY FEATURES Doors-Child safety locks Door locks Moving the lever to “LOCK” will allow the door to be opened only fromthe outside. Seat belts-Shoulder belt anchor Unlock Lock Push up, or squeeze lock release to lower Rear door If belt is fully extended, then retracted even slight...

33 OVER VIEW FEA T URES/OPERA TIONS SAFETY AND EMERGENCY FEA T URES Spare tire & tools Tool and spare tire location Removing the spare tire Tire bagJack Wheel nut wrenchJack handleTire strapSocket adapterSpare tire Refer to the Owner’s Manual for jack positioning and tire changing procedures. Al...

774 Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING 2WD 2 Wheel Drive A/C Air Conditioning ABS Anti-lock Brake System ACC Accessory AI-SHIFT Artificial Intelligence Shift control ALR Automatic Locking Retractor AVG Average AWD All Wheel Drive CRS Child Restraint System ECO Economy/...

24 For your information Main Owner’s Manual Please note that this manual applies to all models and all equipment, includ-ing options. Therefore, you may find some explanations for equipment notinstalled on your vehicle. All specifications provided in this manual are current at the time of printing.H...

26 CAUTION ■ General precautions while driving Driving under the influence: Never drive your vehicle when under the influ-ence of alcohol or drugs that have impaired your ability to operate your vehi-cle. Alcohol and certain drugs delay reaction time, impair judgment andreduce coordination, which co...

27 Symbols used throughout this manual Cautions & Notices Symbols used in illustrations CAUTION This is a warning against anything which may cause death or injury to people ifthe warning is ignored. You are informed about what you must or must not doin order to reduce the risk of injury to yours...

TABLE OF CONTENTS 1 SIENNA AAS_U (OM45460U) 1 AUTO ACCESS SEAT Information regarding the AUTO ACCESS SEAT, including usage procedure 2 Maintenance Checking fuses and replacing the battery of the wireless remote control 3 When trouble arises Points to check when you think a malfunction has occurred I...

3 SIENNA AAS_U (OM45460U) Pictorial index AUTO ACCESS SEAT Wireless remote control P. 16 Head restraint P. 9 Seat position adjustment switch P. 6 Seatback angle adjustment switch P. 6 Seatback angle adjustment switch P. 6 Seat position adjustment switch P. 6 Armrests P. 11 Seat raise/lower switch P....

30 1-1. Key information Keys The following keys are provided with the vehicle. Vehicles without a smart key system (type A) Master keysValet keyKey number plate Vehicles without a smart key system (type B) Master keys (black)Valet key (gray)Key number plate Vehicles with a smart key system Electroni...

31 1-1. Key information 1 Before driving Using the mechanical key (vehicles with a smart key system) To take out the mechanical key,push the release button and takethe key out. The mechanical key can only beinserted in one direction, as thekey only has grooves on oneside. If the key cannot be insert...

32 1-1. Key information ■ When required to leave the vehicle’s key with a parking attendant Lock the glove box as circumstances demand. ( → P. 532) On vehicles without the smart key system, provide the attendant with thevalet key. On vehicles with the smart key system, remove the mechanical key for ...

33 1-1. Key information 1 Before driving NOTICE ■ To prevent key damage Observe the following: ● Do not drop the keys, subject them to strong shocks or bend them. ● Do not expose the keys to high temperatures for a long periods of time. ● Do not get the keys wet or wash them in an ultrasonic washer ...

6 SIENNA AAS_U (OM45460U) 1-1. AUTO ACCESS SEAT AUTO ACCESS SEAT n Operating condition The seat position and seatback angle cannot be adjusted if the AUTO ACCESS SEAT is not stowed correctly inside the vehicle. n Seat movement amount The AUTO ACCESS SEAT can be moved 3.1 in. (80 mm) forward and 1.2 ...

7 1-1. AUTO ACCESS SEAT 1 A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) n Disconnecting the battery Do not disconnect the battery while operating the AUTO ACCESS SEAT. The AUTO ACCESS SEAT will become inoperable. If the battery is disconnected during operation and the AUTO ACCESS SEAT becomes inoperab...

8 1-1. AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) CAUTION n Seatback angle adjustment Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces...

9 1 1-1. AUTO ACCESS SEAT A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) Head restraint n Adjusting the height of the head restraint n Removing the head restraint Head restraint is provided for the AUTO ACCESS SEAT. Up Pull the head restraint up. Down Push the head restraint down while pressing the loc...

10 1-1. AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) n Installing the head restraint CAUTION n Head restraint precautions Observe the following precautions regarding the head restraint. Failure to do so may result in death or serious injury. l Use the head restraint designed for AUTO ACCESS SEAT. l Adju...

11 1 1-1. AUTO ACCESS SEAT A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) Armrests n Wearing the seat belt Wearing the seat belt is easier with the armrest raised. Lower the armrests as far as they will go when rotating or raising/ lowering the AUTO ACCESS SEAT. Raise Lower

12 1-1. AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) CAUTION n When wearing the seat belt Wear the seat belt correctly, passing it underneath the armrest. If the seat belt is caught on the armrest, it may not be fully effective, which could cause death or serious injury in the event of a sudden braking,...

13 1 1-1. AUTO ACCESS SEAT A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) Footrest CAUTION n When operating the footrest Operate the footrest by holding the front edge. You may be injured if your fingers get caught in the rotating parts. Lower the footrest as far as it will go when rotating or raising/...

14 1-1. AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) Correct riding posture Maintain the correct posture while sitting in the seat, as follows: Sit while keeping both knees aligned and inside the AUTO ACCESS SEAT. Lower the armrests and keep both arms inside the armrests and inside the AUTO ACCESS SEAT....

15 1-1. AUTO ACCESS SEAT 1 A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) CAUTION n When sitting in the seat l When the seat is being used by a person who is unable to bend his/her knees or neck, or by a person that is unable to sit far back in the seat, be careful as their head, feet etc. may hit the ...

16 1-1. AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) Wireless remote control Effective range Approximately 3.3 ft. (1 m) from the AUTO ACCESS SEAT The wireless remote control can be used to rotate and raise or lower the AUTO ACCESS SEAT. Indicator light Seat raise switch Seat lower switch

17 1-1. AUTO ACCESS SEAT 1 A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) n Operating conditions l The effective range of the wireless remote control changes in accor-dance with surroundings. l Interference from other radio waves may cause the AUTO ACCESS SEAT to stop moving temporarily even when press...

18 1-1. AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) n Conditions affecting operation If you use the wireless remote control to operate the AUTO ACCESS SEAT at the same time as doing any of the following, the AUTO ACCESS SEAT may not operate properly: l Operating the AUTO ACCESS SEAT using another wirel...

19 1-1. AUTO ACCESS SEAT 1 A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) CAUTION n Wireless remote control precautions Observe the following precautions to reduce the risk of injury. l Operate the AUTO ACCESS SEAT from a position from which you can see the occupant of the seat. l Make sure that the oc...

20 SIENNA AAS_U (OM45460U) 1-2. Operating the AUTO ACCESS SEAT Before operating the AUTO ACCESS SEAT The AUTO ACCESS SEAT (right-hand second seat) can be rotated, raised and lowered electrically to help the seat occupant easily enter and exit the vehicle. Have all operations carried out by an assist...

21 1-2. Operating the AUTO ACCESS SEAT 1 A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) Fold the front passenger seat-back while pulling the seat-back angle lever. Unfasten the seat belt on the AUTO ACCESS SEAT. Adjust the armrest and foot restraint on the AUTO ACCESS SEAT to the down-most position. ST...

22 1-2. Operating the AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) n Beep sounds The beep makes the following sounds in response to operating procedures and conditions. CAUTION n Before operating the AUTO ACCESS SEAT When the seat is being used by a person who is unable to bend his/her knees or neck, or...

23 1-2. Operating the AUTO ACCESS SEAT 1 A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) CAUTION n When operating the AUTO ACCESS SEAT l Check the surroundings for safety, making sure that there are no pedestri-ans, bicycles, etc. Failure to do so may result in an accident. l Do not allow children to pl...

24 1-2. Operating the AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) CAUTION n When operating the AUTO ACCESS SEAT l Make sure that the seat belt is unbuckled. There is a risk that the occupant of the AUTO ACCESS SEAT could be injured. l Do not stand on the footrest. Doing so may damage the footrest, or c...

25 1-2. Operating the AUTO ACCESS SEAT 1 A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) NOTICE n To prevent seat damage l Before operating the AUTO ACCESS SEAT, make sure that there are no luggage items or other obstacles around the moving parts of the seat. The AUTO ACCESS SEAT may be damaged if it hi...

26 1-2. Operating the AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) Moving the AUTO ACCESS SEAT outside the vehicle Park the vehicle on a flat surface and leave the engine run-ning. Shift the shift lever to P and set the parking brake. Confirm the following: • The occupant is sitting correctly in the AUT...

28 1-2. Operating the AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) n Operating conditions Under the following conditions, the seat will not rotate or lower even if the seat lower switch is pressed. l The right-hand sliding door is not opened completely. l The seat belt is caught up in the AUTO ACCESS SE...

29 1-2. Operating the AUTO ACCESS SEAT 1 A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) CAUTION n Before moving the AUTO ACCESS SEAT outside the vehicle l Check that the right-hand third seat occupant is safe. NOTICE n To prevent AUTO ACCESS SEAT damage l Press and hold the wireless remote control swit...

30 1-2. Operating the AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) Returning the AUTO ACCESS SEAT to the vehicle Park the vehicle on a flat surface and leave the engine run-ning. Shift the shift lever to P and set the parking brake. Confirm the following: • The right-hand sliding door is fully open.• Th...

31 1-2. Operating the AUTO ACCESS SEAT 1 A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) n Wireless remote control l When the seat raise switch is pressed, the beep will sound once and the AUTO ACCESS SEAT will begin to operate. The seat will not operate if the switch is pressed repeatedly. l The AUTO A...

32 1-2. Operating the AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) n Jam protection function If the operation of the AUTO ACCESS SEAT is interrupted by collision with an obstacle etc., the beep will sound twice and the seat will retreat slightly and then stop. If this happens, make sure that the hands, ...

33 1-2. Operating the AUTO ACCESS SEAT 1 A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) CAUTION n When the AUTO ACCESS SEAT has been returned to the vehicle l When moving the front passenger seat backward or when tilting down the seatback, make sure that you do not hit the occupant of the AUTO ACCESS S...

34 1-2. Operating the AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) NOTICE n To prevent AUTO ACCESS SEAT damage l Press and hold the wireless remote control switches, instead of pressing them repeatedly. l Wait for approximately 1 second before changing to another switch. l Open the right-hand sliding do...

35 1 1-2. Operating the AUTO ACCESS SEAT A U TO ACCE SS SEAT SIENNA AAS_U (OM45460U) Operating with the seat raise/lower switch If the battery of the wireless remote control has discharged or another malfunction has occurred, the seat raise/lower switch can be used to operate the AUTO ACCESS SEAT. (...

36 1-2. Operating the AUTO ACCESS SEAT SIENNA AAS_U (OM45460U) n Seat raise/lower switch When the seat raise/lower switch is pressed, the beep will sound once and the AUTO ACCESS SEAT will begin to operate. The seat will not operate if the switch is pressed repeatedly. NOTICE n To prevent AUTO ACCES...

34 1-2. Opening, closing and locking the doors Smart key system ∗ ∗ : If equipped The following operations can be performed simply by carrying theelectronic key on your person, for example in your pocket.(The driver should always carry the electronic key.) Locks and unlocks the doors ( → P. 35) Lock...

35 1-2. Opening, closing and locking the doors 1 Before driving Unlocking and locking the doors Front door handles Grip the handle to unlock all thedoors. Make sure to touch the sensor onthe back of the handle. The doors cannot be unlocked for3 seconds after the doors arelocked. Touch the lock senso...

36 1-2. Opening, closing and locking the doors Back door Press the unlock button tounlock all the doors. The door cannot be unlocked for3 seconds after the door islocked. Lock the back door again whenyou leave the vehicle. The backdoor will not lock automaticallyafter it has been opened and thenclos...

37 1-2. Opening, closing and locking the doors 1 Before driving Antenna location and effective range ■ Antenna location Antennas outside cabinAntennas inside cabinAntenna outside luggage com-partment

39 1-2. Opening, closing and locking the doors 1 Before driving ■ Operation signals A buzzer sounds and the emergency flashers flash to indicate that the doorshave been locked/unlocked. (Locked: Once; Unlocked: Twice) ■ When the door cannot be locked by the lock sensor on the upper partof the front ...

40 1-2. Opening, closing and locking the doors ■ Alarms and warning indicators A combination of exterior and interior alarms as well as warnings shown onthe multi-information display are used to prevent theft of the vehicle andunforeseeable accidents resulting from erroneous operation. Perform theap...

42 1-2. Opening, closing and locking the doors * 1 : A message will be shown on the multi-information display in the instru- ment cluster. * 2 : If the engine does not start when the electronic key is inside the vehicle, the electronic key battery may be depleted or there may be difficultiesreceivin...

43 1-2. Opening, closing and locking the doors 1 Before driving ■ Switching the door unlock function It is possible to set which doors the entry function unlocks using the wirelessremote control. Turn the “ENGINE START STOP” switch off. When the indicator on the key surface is not on, press and hold...

44 1-2. Opening, closing and locking the doors ■ Battery-saving function In the following circumstances, the entry function is disabled in order to pre-vent the vehicle battery from discharging and the electronic key battery fromdischarging. ● When the entry function has not been used for 5 days or ...

45 1-2. Opening, closing and locking the doors 1 Before driving ■ Conditions affecting operation The smart key system uses weak radio waves. In the following situations,the communication between the electronic key and the vehicle may beaffected, preventing the smart key system and wireless remote co...

46 1-2. Opening, closing and locking the doors ■ Notes for the entry function ● Even when the electronic key is within the effective range (detectionareas), the system may not operate properly in the following cases. • The electronic key is too close to the window or outside door handle, near the gr...

47 1-2. Opening, closing and locking the doors 1 Before driving ■ Note for locking the doors ● Touching the door lock sensor while wearing gloves may delay or preventlock operation. Remove the gloves and touch the lock sensor again. ● When the lock operation is performed using the lock sensor, recog...

48 1-2. Opening, closing and locking the doors ■ Notes for the unlocking function ● Gripping the front door handle when wearing a glove may not unlock orlock the door. ● A sudden approach to the effective range or door handle operation mayprevent the doors from being unlocked. In this case, return t...

49 1-2. Opening, closing and locking the doors 1 Before driving ■ Electronic key battery depletion ● The standard battery life is 1 to 2 years. ● If the battery becomes low, an alarm will sound in the cabin when theengine stops. ( → P. 40) ● As the electronic key always transmits radio waves, the ba...

51 1-2. Opening, closing and locking the doors 1 Before driving CAUTION ■ Caution regarding interference with electronic devices ● People with implanted pacemakers or cardiac defibrillators should keepaway from the smart key system antennas. ( → P. 38) The radio waves may affect the operation of suc...

53 1-2. Opening, closing and locking the doors 1 Before driving Vehicles without a smart key system (type B) Locks all doorsUnlocks all doors Pressing the button unlocksthe driver’s side doors. Press-ing the button again within3 seconds unlocks the otherdoors. Opens and closes the leftside power sli...

54 1-2. Opening, closing and locking the doors Vehicles with a smart key system Locks all doorsUnlocks all doors Pressing the button unlocksthe driver’s side doors. Press-ing the button again within3 seconds unlocks the otherdoors. Opens and closes the leftside power sliding door(press and hold)Open...

55 1-2. Opening, closing and locking the doors 1 Before driving ■ Operation signals Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked:Twice) Back door: A buzzer sounds and the emergency flashers flash twice to indica...

59 1 1-2. Opening, closing and locking the doors Before driving Front doors The vehicle can be locked and unlocked using the entry function,wireless remote control, key or door lock switch. ■ Entry function (if equipped) → P. 35 ■ Wireless remote control → P. 52 ■ Key Turning the key operates the do...

61 1-2. Opening, closing and locking the doors 1 Before driving Locking the front doors from the outside without a key Move the inside lock button to the lock position.Close the door. Vehicles without a smart key system The doors cannot be locked if either of the front doors is open and thekey is in...

62 1-2. Opening, closing and locking the doors Automatic door locking and unlocking systems The following functions can be set or cancelled: Function Operation Shift position linked door locking function Shifting the shift lever out of P locks all the doors. Shift position linked door unlocking func...

63 1-2. Opening, closing and locking the doors 1 Before driving ■ Setting and canceling the functions To switch between set and canceled, follow the procedure below: Vehicles without a smart key system Close all the doors and turn the engine switch to the “ON”position. (Perform step 2 within 10 seco...

64 1-2. Opening, closing and locking the doors ■ When all the doors are locked with the wireless remote control or key The doors cannot be unlocked with the door lock switch. The door lock switch can be reset by unlocking all the doors with the wire-less remote control or key. ■ Using the mechanical...

65 1 1-2. Opening, closing and locking the doors Before driving Sliding doors Vehicles without power sliding doors The sliding doors can be opened and closed using the sliding doorhandle. The sliding door can be locked and unlocked using the wire-less remote control, door lock switch or inside lock ...

67 1-2. Opening, closing and locking the doors 1 Before driving Canceling the power sliding door system (vehicles with powersliding doors) Turn the main switch off to dis-able the power sliding door sys-tem. Off The sliding doors can only beopened and closed manually. On * The power sliding door can...

68 1-2. Opening, closing and locking the doors Locking the sliding doors from the outside without the wirelessremote control Move the inside lock knob to the lock position.Close the sliding door. Sliding door child-protector locks The sliding door cannot beopened by the inside door han-dle and the s...

69 1-2. Opening, closing and locking the doors 1 Before driving ■ The power sliding door can be operated when (vehicles with powersliding doors) ● Open operation: The shift lever is in P. Close operation: The vehicle is stopped. ● The power sliding door system main switch is on. ● The power sliding ...

71 1-2. Opening, closing and locking the doors 1 Before driving ■ If the power sliding door is inoperative (vehicles with power slidingdoors) When the power sliding door detects an abnormality and stops opening andcan not be completely closed manually, cancel the function as follows andclose the doo...

72 1-2. Opening, closing and locking the doors CAUTION ■ While driving Observe the following precautions while driving.Failure to do so may cause a door to open unexpectedly and an occupant tofall out of the vehicle, resulting in death or serious injury. ● Always use a seat belt. ● Always lock the d...

73 1-2. Opening, closing and locking the doors 1 Before driving CAUTION ■ Operating the sliding doors Observe the following precautions.Failure to do so may cause parts of the body to be caught, resulting in seri-ous injury. ● When opening or closing a sliding door, thoroughly check to make sure the...

76 1-2. Opening, closing and locking the doors CAUTION ■ Jam protection function (vehicles with power sliding doors) Observe the following precautions. Failure to do so may cause serious injury. ● Never use any part of your body to intentionally activate the jam protectionfunction. ● The jam protect...

79 1-2. Opening, closing and locking the doors 1 Before driving Canceling the power back door system (vehicles with powerback door) Turn the main switch off to dis-able the power back door sys-tem. OffOn * * : Orange mark on the switch should be visible when the switchis on. ■ When closing the back ...

80 1-2. Opening, closing and locking the doors ■ If the back door opener is inoperative The back door can be operated from the inside. Move the lever. Vehicles without power back door Vehicles with power back door Remove the inside panel. STEP 1 STEP 2

81 1-2. Opening, closing and locking the doors 1 Before driving ■ The power back door can be operated when ● The shift lever is in P. ● The back door is unlocked. ■ Jam protection function (vehicles with power back door) ● If anything obstructs the power back door while it is closing or opening,the ...

83 1-2. Opening, closing and locking the doors 1 Before driving CAUTION ■ Operating the back door Observe the following precautions.Failure to do so may cause parts of the body to be caught, resulting in seri-ous injury. ● Remove any heavy loads, such as snow and ice, from the back doorbefore openin...

87 1-2. Opening, closing and locking the doors 1 Before driving CAUTION ■ Jam protection function (vehicles with power back door) Observe the following precautions. Failure to do so may cause serious injury. ● Although the back door stops closing when the jam protection functiondetects an object, ta...

88 1-2. Opening, closing and locking the doors NOTICE ■ Back door damper stays The back door is equipped with damper stays that hold the back door inplace. Observe the following precautions. Failure to do so may cause damage to the back door damper stay, resultingin malfunction. ■ To prevent back do...

89 1 Before driving 1-3. Adjustable components (seats, mirrors, steering wheel) Front seats Manual seat Seat position adjustmentleverSeatback angle adjustmentleverVertical height adjustmentlever (driver’s side only)Lumbar support adjustmentknob (driver’s side only)

90 1-3. Adjustable components (seats, mirrors, steering wheel) Power seat Seat position adjustmentswitchSeatback angle adjustmentswitchSeat cushion (front) angleadjustment switch (driver’sside only)Vertical height adjustmentswitch (driver’s side only)Lumbar support adjustmentswitch (driver’s side on...

92 1-3. Adjustable components (seats, mirrors, steering wheel) Entering the vehicle: Wheneither of the following actionshas been performed, the seatwill move forward (auto returnfunction): • Vehicles without a smart key sys- tem: The engine switch has beenturned to the “ACC” position. Vehicles with ...

93 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving ■ Active head restraints Even small forces applied to the seatback may cause the head restraint tomove. When a locked head restraint is pushed up forcibly, the head restraintinner structure may appear. This does not indi...

94 1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats Second seats (Tip-up seat) Seat position adjustmentleverSeatback angle adjustmentlever Second seats (Ottoman seat) Seat position adjustmentleverSeatback angle adjustmentleverOttoman angle adjustmentlever Second seats (AUTO ACC...

97 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving ■ Getting out of the vehicle Tip-up seats Pull the strap and fold down theseatback. The cushion will tip up.The seat can slide forward. Move the seat to the front-mostposition. Make sure that no passenger isseated on the...

98 1-3. Adjustable components (seats, mirrors, steering wheel) Removing the second seats ■ Removing the second outside seats (Tip-up seats) Pull the armrests up. Pull the seatback adjustmentlever and fold down the seat-back. The cushion will tip up. Slide the seat forward to a lock position. Pull th...

99 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving ■ Removing the second outside seats (Ottoman seats) Pull the armrests up. Pull the seatback adjustmentlever and fold down the seat-back. Slide the seat to a forward lock position. Pull the release lever behind theseatbac...

100 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Removing the second center seat (if equipped) Pull the lock release strap andfold down the second centerseatback. Make sure that the head restraintis in the lowest position. Pull the lock release strap underthe seat to remove the seat...

101 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving Installing the second seats ■ Installing the second outside seats Align the marking on the seat side cover to the marking on therail cover. Tip-up seat Align the marking on the seatfront cover to the rail. Ottoman seat ...

102 1-3. Adjustable components (seats, mirrors, steering wheel) Lower the seat and engage the latches. If you locked the seat latches unintentionally before installingsecurely, pull the release lever to unlock the latches. Make sure the seat is locked in place by trying to shake the seatbackand lift...

103 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving Folding down the third seats (manual seats) ■ Before folding the third seats Fold the outside head restraintsand lower the center headrestraint to the lowest position,and stow the seat belt buckles. Stow the center seat...

104 1-3. Adjustable components (seats, mirrors, steering wheel) Folding down the third seats (power seats) You can operate the power third seats when the shift lever is in P. ■ Before folding the third seats Lower the center head restraintsto the lowest position and stowthe seat belt buckles. Stow t...

105 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving Stowing the third seats (manual seats) Before stowing or returning third seat, remove any items from thefloor area to prevent interference with moving parts. ■ Before stowing the third seats Lower the center head restra...

106 1-3. Adjustable components (seats, mirrors, steering wheel) Push the seat against the floorand make sure it is lockedsecurely. Open the flaps. ■ Returning the third seats Return the flaps. Pull the handle and lift up theseat rearward. Push the seat forward and thenengage the front leg locks. Mak...

108 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Before returning the third seats Be sure to move the second seats forward from the rear most posi-tion, as they may interfere with the third seats returning operation. ■ Returning the third seats Return the flaps. Press and hold the r...

109 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving ■ Power third seat ● If the indicator light above the switches flashes three times when the fold-ing/returning switch is pressed, the folding operation will not start. Makesure the shift lever is in P. ● If any of the f...

110 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ When folding the rear seatbacks down Observe the following precautions. Failure to do so may result in death orserious injury. ● Do not fold the seatbacks down while driving. ● Stop the vehicle on level ground, set the parking...

111 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving CAUTION ■ After returning the rear seatbacks or installing seats Observe the following precautions. Failure to do so may result in death orserious injury. ● Make sure the seatback is securely locked by pushing it forwar...

112 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ When adjusting the seat position or the ottoman (vehicles with Otto-man seats) Make sure to leave enough space around the feet so as not to get themcaught. ■ When using the ottoman (vehicles with Ottoman seats) ● Do not sit on...

113 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving NOTICE ■ Stowing the seat belt The seat belts and the buckles must be stowed before you fold down therear seatbacks. ■ To prevent an ottoman malfunction (vehicles with Ottoman seats) ● Do not place any objects in the se...

114 1-3. Adjustable components (seats, mirrors, steering wheel) Driving position memory ∗ ∗ : If equipped Your preferred driving position (the position of the driver’s seat andoutside rear view mirrors) can be memorized and recalled with thetouch of a button. It is also possible to set this function...

115 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving ■ Recalling the memorized position Check that the shift lever is in P. Vehicles without a smart key system Turn the engine switch to the “ON” position. Vehicles with a smart key system Turn the “ENGINE START STOP” switc...

118 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Operating the driving position memory after turning the engine off Vehicles without a smart key system Memorized positions can be activated up to 180 seconds after the driver’sdoor is opened and another 60 seconds after it is closed a...

119 1 1-3. Adjustable components (seats, mirrors, steering wheel) Before driving Head restraints Head restraints are provided for all seats. Front and second outside seats Up Pull the head restraints up. Down Push the head restraint downwhile pressing the lock releasebutton. Second center * and thir...

121 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving ■ Installing the head restraints (front, second and third center seats) CAUTION ■ Head restraint precautions Observe the following precautions regarding the head restraints. Failure todo so may result in death or seriou...

122 1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driv-ing the vehicle. ■ Correct use of the seat belts Extend the shoulder belt sothat it comes fully over theshoulder, but does notcome into contact with thenec...

123 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving Third center seat belt The third center seat belt is a 3-point type restraint with 2 buckles.Both seat belt buckles must be correctly located and securely latchedfor proper operation. Make sure that the buckle issecurel...

126 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may alsolock if you lean forward too quickly. A slow, easy motion will allow the belt toextend so that you can move around fully....

127 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving ■ People suffering illness Obtain medical advice and wear the seat belt in the proper way. ( → P. 122) ■ Child seat belt usage The seat belts of your vehicle were principally designed for persons of adultsize. ● Use a c...

128 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Wearing a seat belt Observe the following precautions to reduce the risk of injury in the event ofsudden braking, sudden swerving or an accident.Failing to do so may cause death or severe injury. ● Ensure that all passengers w...

129 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving CAUTION ■ Seat belt pretensioners ● Do not place anything, such as a cushion, on the front passenger’s seat.Doing so will disperse the passenger’s weight, which prevents the sensorfrom detecting the passenger’s weight p...

130 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ When using the third center seat belt ■ Using a seat belt extender ● Do not wear the seat belt extender if you can fasten the seat belt withoutthe extender. ● Do not use the seat belt extender when installing a child restraint...

131 1 1-3. Adjustable components (seats, mirrors, steering wheel) Before driving Steering wheel CAUTION ■ Caution while driving Do not adjust the steering wheel while driving.Doing so may cause the driver to mishandle the vehicle and cause an acci-dent, resulting in death or serious injury. ■ After ...

132 1-3. Adjustable components (seats, mirrors, steering wheel) Inside rear view mirror Glare from the headlights of vehicles behind can be reduced byusing the following functions. Manual anti-glare inside rear view mirror Normal positionAnti-glare position Auto anti-glare inside rear view mirror In...

134 1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted using the switch. To select a mirror to adjust,press the switch. LeftRight To adjust the mirror, press theswitch. UpRightDownLeft STEP 1 STEP 2

135 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving Folding back the mirrors Manual type Push the mirror back in the direc-tion of the vehicle’s rear. Power type Press the switch to fold the mir-rors. Press it again to extend them tothe original position.

136 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Mirror angle can be adjusted when Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ONmode. ■ When the m...

137 1-3. Adjustable components (seats, mirrors, steering wheel) 1 Before driving CAUTION ■ When driving the vehicle Observe the following precautions while driving.Failing to do so may result in loss of control of the vehicle and cause an acci-dent, resulting in death or serious injury. ● Do not adj...

138 1-4. Opening and closing the windows and moon roof Power windows Window lock switch Press the switch down to lockthe passenger window switches. Use this switch to prevent chil-dren from accidentally opening orclosing a passenger window. The power windows can be opened and closed using the switch...

140 1-4. Opening and closing the windows and moon roof CAUTION ■ Closing the windows Observe the following precautions. Failing to do so may result in death or serious injury. ● Check to make sure that all passengers do not have any part of their bodyin a position where it could be caught when a win...

141 1 1-4. Opening and closing the windows and moon roof Before driving Quarter windows The quarter windows can be opened to bring in fresh outside air foradditional ventilation. Manual type Pull the handle and swing thewindow fully out to open. Power type OpeningClosing Both the left and right quar...

143 1 1-4. Opening and closing the windows and moon roof Before driving Moon roof ∗ ∗ : If equipped Use the overhead switches to open and close the moon roof. ■ Front moon roof Opens the moon roof * The moon roof will stop at thetilt up position once. To tilt down, press the oppositeside of the swit...

145 1-4. Opening and closing the windows and moon roof 1 Before driving ■ Sunshade The sunshade can be opened and closed manually. However, both front andrear sunshades open automatically when the moon roof is opened. ■ When the moon roof does not close normally Stop the vehicle. Press and hold the ...

146 1-4. Opening and closing the windows and moon roof CAUTION ■ Opening the moon roof Observe the following precautions.Failing to do so may cause death or serious injury. ● Do not allow any passengers to put their hands or heads outside the vehi-cle while it is moving. ● Do not sit on top of the m...

147 1 Before driving 1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap: ■ Before refueling the vehicleVehicles without a smart key system Turn the engine switch off and ensure that all the doors and win-dows are closed. Vehicles with a smart key system Tu...

148 1-5. Refueling Closing the fuel tank cap After refueling, turn the fuel tankcap until you hear a click. Oncethe cap is released, it will turnslightly in the opposite direction. Hang the fuel tank cap on theback of the fuel filler door. STEP 3 ■ Fuel type Use unleaded gasoline (Octane rating 87 [...

149 1-5. Refueling 1 Before driving CAUTION ■ When refueling the vehicle Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ● After exiting the vehicle and before opening the fuel door, touch anunpainted metal surface to discharge a...

150 1-5. Refueling CAUTION ■ When refueling Securely insert the fuel nozzle into the fuel filler neck. If fuel is added withthe nozzle slightly lifted away from the fuel filler neck, the automatic shut offfunction may not operate, resulting in fuel overflowing from the tank. ■ When replacing the fue...

151 1 Before driving 1-6. Theft deterrent system Engine immobilizer system ∗ ∗ : If equipped The vehicle’s keys have built-in transponder chips that prevent theengine from starting if a key has not been previously registered inthe vehicle’s on-board computer.Never leave the keys inside the vehicle w...

152 1-6. Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type engine immobilizer system. ■ Conditions that may cause the system to malfunction ● If the grip portion of the key is in contact with a metallic object ● If the key is in close proximity to or touching a key ...

153 1-6. Theft deterrent system 1 Before driving CAUTION ■ Certifications for the immobilizer system Changes or modifications not expressly approved by the party responsiblefor compliance could void the user’s authority to operate the equipment. NOTICE ■ To ensure the system operates correctly Do no...

154 1-6. Theft deterrent system Alarm ∗ ∗ : If equipped The system sounds the alarm and flashes the lights when forcedentry is detected. ■ Triggering of the alarm The alarm is triggered in the following situations: ● A locked door is unlocked or opened in any way other thanusing the entry function, ...

155 1-6. Theft deterrent system 1 Before driving ■ System maintenance The vehicle has a maintenance-free type alarm system. ■ Items to check before locking the vehicle To prevent unexpected triggering of the alarm and vehicle theft, make sureof the following: ● Nobody is in the vehicle. ● The window...

157 1 Before driving 1-7. Safety information Correct driving posture Drive with a good posture as follows: Sit upright and well back inthe seat. ( → P. 89) Adjust the position of theseat forward or backward toensure the pedals can bereached and easilydepressed to the extentrequired. ( → P.89) Adjust...

159 1 1-7. Safety information Before driving SRS airbags The SRS airbags inflate when the vehicle is subjected to certaintypes of severe impacts that may cause significant injury to theoccupants. They work together with the seat belts to help reduce therisk of death or serious injury. SRS front airb...

160 1-7. Safety information Airbag system components Front passenger airbagCurtain shield airbagsSide airbagsFront passenger occupantclassification system (ECUand sensors)Curtain shield airbag sen-sorsFront passenger’s seat beltbuckle switchSRS warning lightDriver airbag Side and curtain shield air-...

162 1-7. Safety information ■ SRS airbag deployment conditions (SRS front airbags) ● The SRS front airbag will deploy in the event of an impact that exceedsthe set threshold level (the level of force corresponding to an approxi-mately 12 - 18 mph [20 - 30 km/h] frontal collision with a fixed wall th...

165 1-7. Safety information 1 Before driving ■ When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. Donot disconnect the battery cables before contacting your Toyota dealer. ● Any of the SRS airbags have been inflated. ● The front of the vehicle ...

166 1-7. Safety information CAUTION ■ SRS airbag precautions Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat beltsproperly.The SRS airbags are supplemental devices to be u...

171 1-7. Safety information 1 Before driving CAUTION ■ Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modificationswithout consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causin...

172 1-7. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica-tion system. This system detects the conditions of the front passen-ger seat and activates or deactivates the devices for the frontpassenger. SRS warning lig...

173 1-7. Safety information 1 Before driving Conditions and operation of the front passenger occupantclassification system ■ Adult * 1 ■ Child * 3 or child restraint system * 4 Indicator/ warning light “AIR BAG ON” and “AIR BAG OFF” indicator lights “AIR BAG ON” SRS warning light Off Front passenger...

175 1-7. Safety information 1 Before driving * 1 : The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may rec-ognize him/her as a child depending on his/her physique and pos-ture. * 2 : In the event the front passenger does not wea...

176 1-7. Safety information CAUTION ■ Front passenger occupant classification system precautions Observe the following precautions regarding the front passenger occupantclassification system. Failure to do so may cause death or serious injury. ● Wear the seat belt properly. ● Make sure the front pas...

177 1-7. Safety information 1 Before driving CAUTION ■ Front passenger occupant classification system precautions ● If an adult sits in the front passenger seat, the “AIR BAG ON” indicatorlight is illuminated. If the “AIR BAG OFF” indicator is illuminated, ask thepassenger to sit up straight, well b...

178 1-7. Safety information Child restraint systems Points to remember Studies have shown that installing a child restraint system on a rearseat is much safer than installing one on the front passenger seat. ● Choose a child restraint system that suits your vehicle and isappropriate to the age and s...

180 1-7. Safety information ■ Selecting an appropriate child restraint system ● Use a child restraint system appropriate for the child until the childbecomes large enough to properly wear the vehicle’s seat belt. ● If the child is too large for a child restraint system, sit the child on a rearseat a...

182 1-7. Safety information Installing child restraints Follow the child restraint system manufacturer’s instructions. Firmlysecure child restraints to the rear seats using the LATCH anchors ora seat belt. Attach the top tether strap when installing a childrestraint. The lap/shoulder belt can be use...

183 1-7. Safety information 1 Before driving Third seats Child restraint LATCH anchors LATCH anchors are providedfor center seat. (Buttons dis-playing the location of theanchors are attached to theseats.) ■ Using the seat belts Seat belts equipped with achild restraint locking mecha-nism (ALR/ELR be...

185 1-7. Safety information 1 Before driving Installation with LATCH system (second seat) Fold the seatback while pullingthe lever and move to the rear-most recline position. Widen the gap between the seat cushion and seatbackslightly. Type A Latch the buckles onto theLATCH anchors. If the childrest...

186 1-7. Safety information Type B Latch the hooks of the lowerstraps onto the LATCH anchors.If the child restraint has a toptether strap, the top tether strapshould be latched onto the toptether strap anchor. For owners in Canada:The symbol on a child restraintsystem indicates the presence ofa lowe...

187 1-7. Safety information 1 Before driving Installation with LATCH system (third seat) Manual seat 1st lock position11th lock position Fold the seatback while pullingthe strap. Return the seatbackand secure it at the 1st lock posi-tion (most upright position).Adjust the seatback to the 11thlock po...

188 1-7. Safety information Widen the gap between the seat cushion and seatbackslightly. Type A Latch the buckles onto theLATCH anchors. If the childrestraint has a top tether strap,the top tether strap should belatched onto the top tether strapanchor. For owners in Canada:The symbol on a child rest...

191 1-7. Safety information 1 Before driving ■ Forward facing ⎯ Convertible seat Place the child restraint systemon the seat facing the front of thevehicle. Run the seat belt through thechild restraint system and insertthe plate into the buckle. Makesure that the belt is not twisted. Fully extend th...

192 1-7. Safety information While pushing the child restraintsystem into the rear seat, allowthe shoulder belt to retract untilthe child restraint system issecurely in place. After the shoulder belt hasretracted to a point where there isno slack in the belt, pull the belt tocheck that it cannot be e...

193 1-7. Safety information 1 Before driving Removing a child restraint installed with a seat belt Push the buckle release buttonand fully retract the seat belt. Child restraint systems with a top tether strap (second seat) Secure the child restraint systemusing the seat belt or LATCHanchors, and ad...

194 1-7. Safety information Adjust the head restraint to thedownmost lock position. Child restraint systems with a top tether strap (third seat) Secure the child restraint systemusing the seat belt or LATCHanchors. Adjust the headrestraint to the uppermost posi-tion. Latch the hook onto the anchorbr...

195 1-7. Safety information 1 Before driving Adjust the head restraint to thedownmost position. STEP 3 ■ Laws and regulations pertaining to anchorages The LATCH system conforms to FMVSS225 or CMVSS210.2.Child restraint systems conforming to FMVSS213 or CMVSS213 specifica-tions can be used.This vehic...

196 1-7. Safety information CAUTION ■ When installing a child restraint system Follow the directions given in the child restraint system installation manualand fix the child restraint system securely in place.If the child restraint system is not correctly fixed in place, the child or otherpassengers...

197 1-7. Safety information 1 Before driving CAUTION ■ When installing a child restraint system ● When installing a child restraint system on the third center seat, adjustboth seatbacks at the same angle. Otherwise, the child restraint systemcannot be securely restrained and this may cause death or ...

198 1-7. Safety information CAUTION ■ When installing a child restraint system to the AUTO ACCESS SEAT (if equipped) ■ Do not use a seat belt extender If a seat belt extender is used when installing a child restraint system, theseat belt will not securely hold the child restraint system, which could...

38 SIENNA AAS_U (OM45460U) 2-1. Maintenance Checking and replacing fuses Fuse layout and amperage rating n AUTO ACCESS SEAT n Engine compartment If the AUTO ACCESS SEAT does not operate when the switches are pressed, a fuse may have blown. If this happens, check and replace the fuses as necessary. A...

39 2-1. Maintenance 2 Ma intena nce SIENNA AAS_U (OM45460U) n After a fuse is replaced Have the vehicle inspected by your Toyota dealer in the following situations. l If the replaced fuse blows again. l If the AUTO ACCESS SEAT does not operate. CAUTION n To prevent system breakdowns and vehicle fire...

40 2-1. Maintenance SIENNA AAS_U (OM45460U) Wireless remote control battery Replace the battery with a new one if it is discharged. n You will need the following items: l Flathead screwdriver l Lithium battery CR2032 n Replacing the battery Remove the cover using a coin protected with tape etc. Remo...

41 2-1. Maintenance 2 Ma intena nce SIENNA AAS_U (OM45460U) n If the wireless remote control battery is discharged The wireless remote control will not function properly. n Use a CR2032 lithium battery l Batteries can be purchased at your Toyota dealer, local electrical appli-ance shops or camera st...

42 2-1. Maintenance SIENNA AAS_U (OM45460U) NOTICE n For normal operation after replacing the battery Observe the following precautions to prevent accidents. l Always work with dry hands. Moisture may cause the battery to rust. l Do not touch or move any other components inside the wireless remote c...

200 2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv-ing: ■ Starting the engine → P. 212 ■ Driving With the brake pedal depressed, shift the shift lever to D. ( → P. 221) Release the parking brake. ( → P. 227) Gradually release the brake ped...

201 2-1. Driving procedures 2 When drivin g Starting off on a steep uphill Make sure that the parking brake is set and shift the shift leverto D.Gently depress the accelerator pedal.Release the parking brake. ■ Parking the vehicle With the shift lever in D, depress the brake pedal.Set the parking br...

203 2-1. Driving procedures 2 When drivin g ■ Eco-friendly driving CAUTION ■ When starting the vehicle Always keep your foot on the brake pedal while stopped with the engine run-ning. This prevents the vehicle from creeping. ■ When driving the vehicle ● Do not drive if you are unfamiliar with the lo...

206 2-1. Driving procedures CAUTION ■ When driving on slippery road surfaces ● Sudden braking, acceleration and steering may cause tire slippage andreduce your ability to control the vehicle, resulting in an accident. ● Sudden changes in engine speed, such as engine braking caused by up-shifting and...

207 2-1. Driving procedures 2 When drivin g CAUTION ■ When the vehicle is stopped ● Do not race the engine. If the vehicle is in any gear other than P or N, the vehicle may acceleratesuddenly and unexpectedly, causing an accident. ● Do not leave the vehicle with the engine running for a long time.If...

208 2-1. Driving procedures CAUTION ● Do not attach adhesive discs to the windshield or windows. Do not placecontainers such as air fresheners on the instrument panel or dashboard.Adhesive discs or containers may act as lenses, causing a fire in the vehi-cle. ● If a curved glass is coated with a met...

209 2-1. Driving procedures 2 When drivin g CAUTION ■ When taking a nap in the vehicle Always turn the engine off. Otherwise, if you accidentally move the shift leveror depress the accelerator pedal, this could cause an accident or fire due toengine overheating. Additionally, if the vehicle is parke...

210 2-1. Driving procedures NOTICE ■ When driving the vehicle ● Do not depress the accelerator and brake pedals at the same time duringdriving, as this may restrain the engine output. ● Do not use the accelerator pedal or depress the accelerator and brakepedals at the same time to hold the vehicle o...

211 2-1. Driving procedures 2 When drivin g NOTICE ■ When encountering flooded roads Do not drive on a road that has flooded after heavy rain etc. Doing so maycause the following serious damage to the vehicle: ● Engine stalling ● Short in electrical components ● Engine damage caused by water immersi...

212 2-1. Driving procedures Engine (ignition) switch (vehicles without smart key system) ■ Starting the engine Check that the parking brake is set.Check that the shift lever is set in P.Firmly depress the brake pedal.Turn the engine switch to the “START” position to start theengine. ■ Changing the e...

213 2-1. Driving procedures 2 When drivin g ■ Turning the key from “ACC” to “LOCK” Shift the shift lever to P. ■ If the engine does not start (vehicles with engine immobilizer system) The engine immobilizer system may not have been deactivated. ( → P. 151) ■ When the steering lock cannot be released...

214 2-1. Driving procedures CAUTION ■ When starting the engine Always start the engine while sitting in the driver’s seat. Do not depress theaccelerator pedal while starting the engine under any circumstances.Doing so may cause an accident resulting in death or serious injury. ■ Caution when driving...

216 2-1. Driving procedures ■ Changing “ENGINE START STOP” switch modes Modes can be changed by pressing the “ENGINE STARTSTOP” switch with the brake pedal released. (The modechanges each time the switch is pressed.) Off * Emergency flashers can beused. ACCESSORY mode Some electrical componentssuch ...

218 2-1. Driving procedures ■ Electronic key battery depletion → P. 49 ■ Conditions affecting operation → P. 45 ■ Note for the entry function → P. 46 ■ If the engine does not start The engine immobilizer system may not have been deactivated. ( → P. 151) ■ Steering lock After turning the “ENGINE STAR...

221 2-1. Driving procedures 2 When drivin g Automatic transaxle Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever Vehicles without a smart key system: While the engine switch is in the “ON” position, move theshift lever with the brake pedal depressed.Vehicles...

222 2-1. Driving procedures ■ Shift position purpose * 1 : Shifting to the D position allows the system to select a gear suitable for the driving conditions. Setting the shift lever to the D position isrecommended for normal driving. * 2 : Selecting shift ranges using S mode restricts the upper limi...

223 2-1. Driving procedures 2 When drivin g Changing shift ranges in S mode When the shift lever is in the S position, the shift lever can be oper-ated as follows: UpshiftingDownshifting The initial shift range in S mode is set automatically to “5” or “4”according to vehicle speed. However, the init...

225 2-1. Driving procedures 2 When drivin g ■ Downshift restriction warning buzzer (S mode) To help ensure safety and driving performance, downshifting operation maysometimes be restricted. In some circumstances, downshifting may not bepossible even when the shift lever is operated. (A buzzer will s...

226 2-1. Driving procedures Turn signal lever ■ Turn signals can be operated when Vehicles without a smart key system: The engine switch is in the “ON” position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode. ■ If the indicator flashes faster than usual Chec...

227 2-1. Driving procedures 2 When drivin g Parking brake ■ Usage in winter time See “Winter driving tips” for parking brake usage in winter time. ( → P. 324) NOTICE ■ Before driving Fully release the parking brake.Driving the vehicle with the parking brake set will lead to brake componentsoverheati...

228 2-1. Driving procedures Horn ■ After adjusting the steering wheel Make sure that the steering wheel is securely locked.The horn may not sound if the steering wheel is not securely locked.( → P. 131) To sound the horn, press on orclose to the mark.

229 2 When drivin g 2-2. Instrument cluster and information display Gauges and meters Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Engine coolant temperature gauge Displays the ...

230 2-2. Instrument cluster and information display Changing the display Pressing this button switches among odometer display, trip meter dis-plays and Eco Driving Indicator Light setting screen. OdometerTrip meter A * 1 Trip meter B * 1 Eco Driving Indicator Lightsetting screen * 2 * 1 : Pressing a...

231 2-2. Instrument cluster and information display 2 When drivin g ■ The meters and display illuminate when (Optitron type meters) Vehicles without a smart key system: The engine switch is in the “ON” position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode....

232 2-2. Instrument cluster and information display Indicators and warning lights The indicator and warning lights on the instrument cluster and cen-ter panel inform the driver of the status of the vehicle’s various sys-tems. ■ Instrument cluster ■ Center display

233 2-2. Instrument cluster and information display 2 When drivin g ■ Indicators The indicators inform the driver of the operating state of thevehicle’s various systems. Turn signal indicator ( → P. 226) (if equipped) Cruise control indicator ( → P. 271, 275) Headlight high beam indicator ( → P. 252...

235 2-2. Instrument cluster and information display 2 When drivin g ■ Warning lights Warning lights inform the driver of malfunctions in any of thevehicle’s systems. ( → P. 681) * 1 : These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with a smart key sy...

236 2-2. Instrument cluster and information display CAUTION ■ If a safety system warning light does not come on Should a safety system light such as the ABS or SRS airbag warning lightnot come on when you start the engine, this could mean that these systemsare not available to help protect you in an...

237 2-2. Instrument cluster and information display 2 When drivin g Multi-information display ∗ ∗ : If equipped The multi-information display presents the driver with a variety ofdriving-related data, including the clock and current outside temper-ature. The display varies depending on its specifica...

238 2-2. Instrument cluster and information display Switching the display “INFO” button“SELECT RESET” button“SETUP” button Display items Display items can be switched by pressing the “INFO” button. The display varies depending on its specification. ■ Average Fuel Economy ■ Current Fuel Economy ● War...

239 2-2. Instrument cluster and information display 2 When drivin g ■ Distance to Empty ■ Average Speed ■ Trip Timer Displays the estimated maximum distance thatcan be driven with the quantity of fuel remaining. ● This distance is computed based on your aver-age fuel consumption. As a result, the ac...

240 2-2. Instrument cluster and information display Set up display ■ Before setting Press the “SETUP” button while the vehicle is stopped. The “Custom Settings” screen is displayed on the multi-informationdisplay. If left idle for approximately 20 seconds, the display will revert to theprevious scre...

241 2-2. Instrument cluster and information display 2 When drivin g ■ Setting the clock Select “Clock” on the “Display Settings” screen, and press the“SELECT RESET” button. Press the “INFO” button to adjustthe hours and the “SETUP” but-ton to adjust the minutes. Press the “SELECT RESET” but-ton to s...

242 2-2. Instrument cluster and information display ■ Selecting the language Select “Language” on the “Display Settings” screen, andpress the “SELECT RESET” button. Select the language you want toread by pressing the “INFO” or“SETUP” button. Press the “SELECT RESET” but-ton to set the language. The ...

243 2-2. Instrument cluster and information display 2 When drivin g ● Setting the brightness Select “Brightness” on the“Screen Settings” screen, andpress the “SELECT RESET” but-ton. Press the “INFO” or “SETUP”button to adjust the brightness. +: Brighter-: Darker Press the “SELECT RESET” but-ton to e...

246 2-2. Instrument cluster and information display Press the “INFO” or “SETUP”button to adjust the contrast. +: Strengthen-: Weaken Press the “SELECT RESET” but-ton to exit the screen. ● Setting the color Select “Color” on the “ScreenSettings” screen, and press the“SELECT RESET” button. Press the “...

247 2-2. Instrument cluster and information display 2 When drivin g ● Setting the tone Select “Tone” on the “ScreenSettings” screen, and press the“SELECT RESET” button. Press the “INFO” or “SETUP”button to adjust the tone. +: Brighter-: Darker Press the “SELECT RESET” but-ton to exit the screen. ■ R...

249 2-2. Instrument cluster and information display 2 When drivin g ■ Eco Driving Indicator Eco Driving Indicator Light During Eco-friendly acceleration (Ecodriving), Eco Driving Indicator Light willturn on. Eco Driving Indicator Zone Display * Suggests Zone of Eco driving with cur-rent Eco driving ...

251 2 When drivin g 2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. U.S.A. The side marker, park-ing, tail, license plate,daytime running lights (ifequipped) and instru-ment panel lights turnon.The headlights and alllights listed above ...

252 2-3. Operating the lights and wipers Turning on the high beam headlights With the headlights on, pushthe lever away from you toturn on the high beams. When the light switch is in position, the Automatic HighBeam system will be activated.( → P. 257) Pull the lever toward you to thecenter position...

253 2-3. Operating the lights and wipers 2 When drivin g Manual headlight leveling dial (vehicles with dischargeheadlights) The level of the headlight aim can be adjusted according to the num-ber of passengers and the loading condition of the vehicle. Raises the level of the head-lightsLowers the le...

254 2-3. Operating the lights and wipers ■ Daytime running light system (if equipped) ● To make your vehicle more visible to other drivers, the headlights turn onautomatically (at a reduced intensity) whenever the engine is started andthe parking brake is released. Daytime running lights are not des...

255 2-3. Operating the lights and wipers 2 When drivin g ■ Automatic light off system Vehicles without a smart key system ● When the headlights are on: The headlights and tail lights turn off 30 sec-onds after a door is opened and closed if the engine switch is turned to the “ACC” or “LOCK” position...

257 2-3. Operating the lights and wipers 2 When drivin g Automatic High Beam ∗ ∗ : If equipped The Automatic High Beam uses an in-vehicle camera sensor toassess the brightness of streetlights, the lights of oncoming andpreceding vehicles, etc., and automatically turns high beam on or offas necessary...

258 2-3. Operating the lights and wipers ■ Turning the high beam on/off manually Switching to low beam Pull the lever to the originalposition. Switching to high beam Turn the light switch to the position.

259 2-3. Operating the lights and wipers 2 When drivin g ■ High beam automatic turning on or off conditions When all of the following conditions are fulfilled, high beam will beautomatically turned on (after approximately 1 second): ● Vehicle speed is above approximately 20 mph (32 km/h). ● The area...

260 2-3. Operating the lights and wipers ■ Limitations of the Automatic High Beam Do not rely on the Automatic High Beam. Always drive safely, taking care toobserve your surroundings and turning high beam on or off manually if nec-essary. ■ Camera sensor detection information ● High beam may not be ...

262 2-3. Operating the lights and wipers ■ If the Automatic High Beam indicator flashes... It may indicate a malfunction in the system. Contact your Toyota dealer. ■ Customization that can be configured at Toyota dealer or by the multi-information display The Automatic High Beam can be turned off.(C...

263 2-3. Operating the lights and wipers 2 When drivin g NOTICE ■ Camera sensor ● Do not touch the camera sensor. ● Do not subject the inside rear view mirror or the camera sensor to a strongimpact. ● Do not disassemble the camera sensor. ● Do not spill liquid onto the inside rear view mirror or the...

264 2-3. Operating the lights and wipers Fog light switch ∗ ■ Fog lights can be used when The headlights are on in low beam. ∗ : If equipped The fog lights secure excellent visibility in difficult driving condi-tions, such as in rain and fog. Turns the front fog lights offTurns the front fog lights ...

265 2-3. Operating the lights and wipers 2 When drivin g Windshield wipers and washer Intermittent windshield wipers with interval adjuster The wiper operation is selected by moving the lever as follows.When intermittent windshield wiper operation is selected, thewiper interval can be also adjusted....

268 2-3. Operating the lights and wipers ■ The windshield wipers and washer can be operated when Vehicles without a smart key system: The engine switch is in the “ON” position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode. ■ Raindrop sensor (vehicles with r...

269 2-3. Operating the lights and wipers 2 When drivin g NOTICE ■ When the windshield is dry Do not use the wipers, as they may damage the windshield. ■ When the washer fluid tank is empty Do not operate the switch continually as the washer fluid pump may over-heat. ■ When a nozzle becomes blocked I...

270 2-3. Operating the lights and wipers Rear window wiper and washer ■ The rear window wiper and washer can be operated when Vehicles without a smart key system: The engine switch is in the “ON” position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode. NOTIC...

271 2 When drivin g 2-4. Using other driving systems Cruise control ∗ ∗ : If equipped Use cruise control to maintain a set speed without depressing theaccelerator pedal. IndicatorsCruise control switch ■ Setting the vehicle speed Press the “ON-OFF” button toactivate the cruise control. Press the but...

273 2-4. Using other driving systems 2 When drivin g ■ Cruise control can be set when ● The shift lever is in D or more than 4 range of S has been selected. ● Vehicle speed is above approximately 25 mph (40 km/h). ■ Accelerating The vehicle can be accelerated normally. After acceleration, the set sp...

274 2-4. Using other driving systems CAUTION ■ To avoid operating the cruise control by mistake Switch the cruise control off using the “ON-OFF” button when not in use. ■ Situations unsuitable for cruise control Do not use cruise control in any of the following situations.Doing so may result in loss...

275 2-4. Using other driving systems 2 When drivin g Dynamic radar cruise control ∗ ∗ : If equipped Dynamic radar cruise control supplements conventional cruise con-trol with a vehicle-to-vehicle distance control. In vehicle-to-vehicledistance control mode, the vehicle automatically accelerates orde...

276 2-4. Using other driving systems ■ Setting the vehicle speed (vehicle-to-vehicle distance con-trol mode) Press the “ON-OFF” button toactivate the cruise control. Press the button again todeactivate the cruise control. Accelerate or decelerate thevehicle to the desired speed,and push the lever do...

277 2-4. Using other driving systems 2 When drivin g ■ Adjusting the set speed To change the set speed, operate the lever until the desired setspeed is displayed. Increases the speedDecreases the speed Fine adjustment: Momentarilymove the lever in the desireddirection. Large adjustment: Hold theleve...

280 2-4. Using other driving systems Example of constant speed cruising When there are no vehicles ahead The vehicle travels at the speed set by the driver. The desired vehicle-to-vehicle distance can also be set by operating the vehicle-to-vehicle dis-tance control. Example of deceleration cruising...

281 2-4. Using other driving systems 2 When drivin g Selecting conventional constant speed control mode Dynamic radar cruise control can be used as conventional cruisecontrol if you select constant speed control mode. Press the “ON-OFF” button toactivate the cruise control. Press the button again to...

282 2-4. Using other driving systems ■ Dynamic radar cruise control can be set when ● The shift lever is in D or more than 4 range of S has been selected. ● Vehicle speed is above approximately 30 mph (50 km/h). ■ Switching modes The mode cannot be switched to constant speed control mode if vehicle-...

284 2-4. Using other driving systems ■ Approach warning In the following instances, there is a possibility that the warnings will notoccur: ● When the speed of the vehicle ahead matches or exceeds your vehiclespeed ● When the vehicle ahead is traveling at an extremely slow speed ● Immediately after ...

285 2-4. Using other driving systems 2 When drivin g CAUTION ■ Before using dynamic radar cruise control Do not overly rely on vehicle-to-vehicle distance control.Be aware of the set speed. If automatic deceleration/acceleration is notappropriate, adjust the vehicle speed, as well as the distance be...

286 2-4. Using other driving systems CAUTION ■ Situations unsuitable for dynamic radar cruise control Do not use dynamic radar cruise control in any of the following situations.Doing so may result in inappropriate speed control and could cause an acci-dent resulting in death or serious injury. ● In ...

287 2-4. Using other driving systems 2 When drivin g CAUTION ■ Conditions under which the vehicle-to-vehicle distance control maynot function correctly Apply the brakes as necessary in the following conditions as the radar sen-sor may not be able to correctly detect vehicles ahead, and a fatal or se...

288 2-4. Using other driving systems Intuitive parking assist ∗ ∗ : If equipped The distance from your vehicle to nearby obstacles when parallelparking or maneuvering into a garage is measured by the sensorsand communicated via the multi-information display, the touchscreen and a buzzer. Always chec...

289 2-4. Using other driving systems 2 When drivin g Display When the sensors detect an obstacle, a graphic is shown on the multiinformation display or touch screen depending on the position anddistance to the obstacle. Multi-information display Touch screen (with navigation system) * * : Depending ...

290 2-4. Using other driving systems The distance display and buzzer When a sensor detects an obstacle, the direction of and the approxi-mate distance to the obstacle are displayed and the buzzer sounds. ■ Corner sensor operation and distance to an obstacle The system operates when the vehicle appro...

291 2-4. Using other driving systems 2 When drivin g ■ Back sensor operation and distance to an obstacle The system operates when the vehicle approaches within the fol-lowing distances to an obstacle. The indicator flashes and thebuzzer sounds when the system is operating. Approximate distance to ob...

292 2-4. Using other driving systems Detection range of the sensors Approximately 2.0 ft. (60 cm)Approximately 2.8 ft. (85 cm)Approximately 5.9 ft. (180 cm) The diagram shows the detectionrange of the sensors. Note thatthe sensors cannot detect obsta-cles that are extremely close tothe vehicle. The ...

293 2-4. Using other driving systems 2 When drivin g ■ Sensor detection information ● Certain vehicle conditions and the surrounding environment may affectthe ability of the sensor to correctly detect obstacles. Particular instanceswhere this may occur are listed below. • There is dirt, snow or ice ...

294 2-4. Using other driving systems ■ If the display flashes and a message is displayed → P. 694 ■ Certification (Canada only) This ISM device complies with Canadian ICES-001. CAUTION ■ Caution when using the Intuitive parking assist-sensor Observe the following precautions. Failure to do so may re...

295 2-4. Using other driving systems 2 When drivin g Rear view monitor system ∗ ∗ : If equipped The rear view monitor system assists the driver by displaying animage of the area behind the vehicle while reversing. The image isdisplayed in reverse on the screen. This reversed image is a similarimage ...

296 2-4. Using other driving systems ■ Displayed area The area covered by the camera is lim-ited. Objects that are close to either cor-ner of the bumper or under the bumpercannot be seen on the screen. The area displayed on the screen mayvary depending on vehicle orientation orroad conditions. Corne...

298 2-4. Using other driving systems CAUTION ■ When using the rear view monitor system Observe the following precautions to avoid an accident that could result indeath or serious injuries: ● Never depend solely on the monitor system when reversing. ● Always check visually and with the mirrors to con...

299 2-4. Using other driving systems 2 When drivin g Driving assist systems To help enhance driving safety and performance, the following sys-tems operate automatically in response to various driving situations.Be aware, however, that these systems are supplementary andshould not be relied upon too ...

303 2-4. Using other driving systems 2 When drivin g ■ Reduced effectiveness of the EPS system The effectiveness of the EPS system is reduced to prevent the system fromoverheating when there is frequent steering input over an extended period oftime. The steering wheel may feel heavy as a result. Sho...

304 2-4. Using other driving systems CAUTION ■ When Enhanced VSC is activated The slip indicator light flashes. Always drive carefully. Reckless driving maycause an accident. Exercise particular care when the indicator light flashes. ■ When TRAC and VSC systems are turned off Be especially careful a...

305 2-4. Using other driving systems 2 When drivin g Hill-start assist control ∗ ■ Hill-start assist control can be operated when • The shift lever is in a position other than P.• The parking brake is not applied.• The accelerator pedal is not depressed. ■ Hill-start assist control ● While hill-star...

306 2-4. Using other driving systems ■ Hill-start assist control buzzer ● When hill-start assist control is activated, the buzzer will sound once. ● In the following situations, hill-start assist control will be canceled and thebuzzer will sound twice. • No attempt is made to drive the vehicle withi...

309 2-4. Using other driving systems 2 When drivin g ■ The pre-collision system is operational when ● Pre-collision seat belts (linked to the radar sensor): • Vehicle speed is greater than about 3 mph (5 km/h).• The speed at which your vehicle is approaching the obstacle or oncom- ing vehicle is gre...

312 2-4. Using other driving systems CAUTION ■ Limitations of the pre-collision system Do not overly rely on the pre-collision system. Always drive safely, takingcare to observe your surroundings and checking for any obstacles or otherroad hazards. ■ Cautions regarding the assist contents of the sys...

314 2-5. Driving information Cargo and luggage Take notice of the following information about storage precau-tions, cargo capacity and load: ● Stow cargo and luggage in the luggage compartment wheneverpossible. ● Be sure all items are secured in place. ● To maintain vehicle balance while driving, po...

316 2-5. Driving information Example based on your vehicle Cargo capacityTotal load capacity When 2 people with the combined weight of 366 lb. (166 kg) areriding in your vehicle, which has a total load capacity of 1660 lb.(750 kg) * , the available amount of cargo and luggage load capacity will be a...

318 2-5. Driving information Seating configuration variation Cargo capacityWeight of the removed secondseat If removing the second seats, it is possible to load extra cargo equalto the weight of the removed seats. (Cargo capacity) = (Total load capacity) - (Total weight of occupants)+ (Weight of the...

319 2-5. Driving information 2 When drivin g CAUTION ■ Things that must not be carried in the luggage compartment The following things may cause a fire if loaded in the luggage compart-ment: ● Receptacles containing gasoline ● Aerosol cans ■ Storage precautions Observe the following precautions.Fail...

320 2-5. Driving information CAUTION ■ Capacity and distribution ● Do not exceed the maximum axle weight rating or the total vehicleweight rating. ● Even if the total load of occupant’s weight and the cargo load is lessthan the total load capacity, do not apply the load unevenly. Improper loading ma...

321 2-5. Driving information 2 When drivin g NOTICE ■ When loading cargo Be careful not to scratch the surface of the moon roof.

322 2-5. Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity,towing capacity and cargo capacity. ■ Total load capacity: ( → P. 734) Total load capacity means the combined weight of occupants, cargoand luggage. ■ Seating capacity: 7 or 8 occupants...

323 2-5. Driving information 2 When drivin g ■ Total load capacity and seating capacity These details are also described on the tire and loading informationlabel. ( → P. 636) CAUTION ■ Overloading the vehicle Observe the total load capacity when you load the vehicle. ( → P. 734) Otherwise, it may no...

324 2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before drivingthe vehicle in winter. Always drive the vehicle in a manner appropri-ate to the prevailing weather conditions. ■ Pre-winter preparations ● Use fluids that are appropriate to the prevai...

325 2-5. Driving information 2 When drivin g Selecting tire chains Use the tire chains of correct size and type. Use SAE Class “S” type radial tire chains, with the exception of radialcable chains or V-bar type chains. Regulations on the use of tire chains Regulations regarding the use of tire chain...

326 2-5. Driving information ■ Tire chain installation Observe the following precautions when installing and removing chains. ● Install and remove tire chains in a safe location. ● Install tire chains on the front tires only. Do not install tire chains on therear tires. ● Install tire chains on fron...

327 2-5. Driving information 2 When drivin g CAUTION ■ Driving with tire chains Observe the following precautions to reduce the risk of accidents.Failing to do so may result in the vehicle being unable to be driven safely,and may cause death or serious injury. ● Do not drive in excess of the speed l...

328 2-5. Driving information Trailer towing Weight limits Confirm that the gross trailer weight, gross combination weight, grossvehicle weight, gross axle weight and trailer tongue load are all withinthe limits. ● The gross trailer weight must never exceed towing capacitydescribed below. 1AR-FE engi...

330 2-5. Driving information Towing related term Towing related term Meaning GVWR (Gross Vehicle Weight Rating) The maximum allowable gross vehicle weight. The gross vehicle weight is the total weight of the vehicle. When towing a trailer, it is the sum of the vehicle weight (including the occupants...

332 2-5. Driving information Selecting trailer ball Use the correct trailer ball for your application. Trailer ball load rating Matches or exceeds the grosstrailer weight rating of the trailer. Ball diameter Matches the size of the trailercoupler. Most couplers arestamped with the required trailerba...

333 2-5. Driving information 2 When drivin g Trailer towing tips Your vehicle will handle differently when towing a trailer. The 3 maincauses of vehicle-trailer accidents are driver error, excessive speedand improper trailer loading. Keep the following in mind when towing: ● Before starting out, che...

335 2-5. Driving information 2 When drivin g ● Always place wheel blocks under both the vehicle and the trailerwheels when parking. Apply the parking brake firmly, and put thetransmission in P. Avoid parking on a slope, but if unavoidable, doso only after performing the following: Apply the brakes a...

338 2-5. Driving information CAUTION ■ Trailer towing precautions ● Follow all the instructions described in this section. Failure to do so couldcause an accident resulting in death or serious injury. ● Exceeding the towing capacity, GVWR, GCWR or GAWR can cause anaccident resulting in death or seri...

339 2-5. Driving information 2 When drivin g CAUTION ■ Hitches ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight requirement. ● Follow the directions supplied by the hitch manufacturer. ● Lubricate the hitch ball with a...

340 2-5. Driving information NOTICE ■ When installing a trailer hitch ● Use only the position recommended by your Toyota dealer. Do not installthe trailer hitch on the bumper; this may cause body damage. ● Do not use axle-mounted hitches, as they can cause damage to the axlehousing, wheel bearings, ...

341 2-5. Driving information 2 When drivin g Dinghy towing NOTICE ■ To avoid serious damage to your vehicle ■ To prevent causing serious damage to the transaxle and Active TorqueControl 4WD system (AWD models) Your vehicle is not designed to be dinghy towed (with 4 wheels onthe ground) behind a moto...

44 SIENNA AAS_U (OM45460U) 3-1. When you think a malfunction has occurred AUTO ACCESS SEAT If the AUTO ACCESS SEAT does not move Reason Correction procedure The seat belt of the AUTO ACCESS SEAT is buckled. Unbuckle the seat belt and try operating the AUTO ACCESS SEAT again. The right-hand sliding d...

46 3-1. When you think a malfunction has occurred SIENNA AAS_U (OM45460U) If the AUTO ACCESS SEAT retreats a little and then stops If the shift lever cannot be moved from P If the seat position or the seatback angle of the AUTO ACCESS SEAT cannot be adjusted Reason Correction procedure The AUTO ACCE...

3 When troub le arise s 47 3-1. When you think a malfunction has occurred SIENNA AAS_U (OM45460U) If the AUTO ACCESS SEAT does not move while outside the vehicle Initializing the seat position information If the AUTO ACCESS SEAT does not move, first initialize the seat position information. Shift th...

3 When troub le arise s 49 3-1. When you think a malfunction has occurred SIENNA AAS_U (OM45460U) If the AUTO ACCESS SEAT moves when a switch is pressed l Initialize the seat position information before conducting the opera-tions listed here. l The movements of the seat while conducting these operat...

3 When troub le arise s 53 3-1. When you think a malfunction has occurred SIENNA AAS_U (OM45460U) If the AUTO ACCESS SEAT does not move even when a switch is pressed Before conducting this procedure, conduct the procedures explained in the “Initializing the seat position information” and “If the AUT...

54 3-1. When you think a malfunction has occurred SIENNA AAS_U (OM45460U) Take out the combination wrench. Removal Replacement Remove the connector. Turn the bolt with yellow marking using the combination wrench, and move the AUTO ACCESS SEAT until the marks are aligned as shown in the illustration....

3 When troub le arise s 57 3-1. When you think a malfunction has occurred SIENNA AAS_U (OM45460U) Turn the power sliding door main switch off and close the right-hand sliding door manually. Have the seat inspected by your Toyota dealer immediately. The power sliding door will not operate if the AUTO...

58 3-1. When you think a malfunction has occurred SIENNA AAS_U (OM45460U) CAUTION n When stowing the AUTO ACCESS SEAT manually Do not put your feet or hands into the AUTO ACCESS SEAT stowage space. Your feet or hands may be caught in the movable parts of the AUTO ACCESS SEAT, which could cause injur...

3 When troub le arise s 59 3-1. When you think a malfunction has occurred SIENNA AAS_U (OM45460U) Wireless remote control If the AUTO ACCESS SEAT does not move Reason Correction procedure The wireless remote control is too far away from the vehicle. Move to within approximately 3.3 ft. (1 m) of the ...

344 3-1. Using the air conditioning system and defogger Front manual air conditioning system ∗ Adjusting the settings ■ Basic setting To turn on the air conditioning system and adjust the fan speed, press “ ∧ ” on to increase the fan speed and “ ∨ ” to decrease the fan speed. The fan speed is shown ...

345 3-1. Using the air conditioning system and defogger 3 Interior fe atures Driver’s side temperature control dial Turn the temperature control dial clockwise (warm) or coun-terclockwise (cool). If is not pressed, the system will blow ambient temperature air or heated air. For quick cooling, turn t...

346 3-1. Using the air conditioning system and defogger To change the air outlets, press , , or . Air flows as shown below according to the mode selected. Air flows to the upper body. Air flows to the upper body andfeet. Air flows mainly to the feet. STEP 3

347 3-1. Using the air conditioning system and defogger 3 Interior fe atures Air flows to the feet and thewindshield defogger operates. ■ Switching between outside air and recirculated air modes Press . The mode switches between outside air mode (introduces air from out-side the vehicle) (indicator ...

348 3-1. Using the air conditioning system and defogger ■ Adjusting rear fan speed Press “ ∧ ” on to increase the fan speed and “ ∨ ” to decrease the fan speed. The fan speed is shown on the control panel. (4 levels) Press to turn the fan off. Defogging the windshield Press . The air conditioning sy...

349 3-1. Using the air conditioning system and defogger 3 Interior fe atures Adjusting the position of and opening and closing the air outlets Center outlets Direct air flow to the left or right,up or down. Right and left side outlets Adjusting: Direct air flow to the left or right, up ordown. Openi...

351 3-1. Using the air conditioning system and defogger 3 Interior fe atures CAUTION ■ To prevent the windshield from fogging up Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the wind-shield can cause the outer ...

352 3-1. Using the air conditioning system and defogger Front automatic air conditioning system ∗ ∗ : If equipped Airflow and outlets are automatically adjusted according to the tem-perature setting. Control panel Changes the rear air outlets used Simultaneous mode Passenger’s side temperature contr...

353 3-1. Using the air conditioning system and defogger 3 Interior fe atures Using the automatic mode Press . The air conditioning system will begin to operate. In outside air orrecirculated air mode, air outlets, fan speed and air conditioning on/off are automatically adjusted according to the temp...

354 3-1. Using the air conditioning system and defogger Adjusting the settings ■ Adjusting the temperature setting Turn the temperature control dial clockwise (warm) or counter-clockwise (cool). The air conditioning system switches between individual and simulta- neous modes each time is pressed. In...

355 3-1. Using the air conditioning system and defogger 3 Interior fe atures Adjusting the settings manually ■ Basic setting To turn on the air conditioning system and adjust the fan speed, press “ ∧ ” on to increase the fan speed and “ ∨ ” to decrease the fan speed. Press to turn the fan off. To ad...

356 3-1. Using the air conditioning system and defogger The air outlets switch each time is pressed. The air flow shown on the display indicates the following. Air flows to the upper body. Air flows to the upper body andfeet. Air flows mainly to the feet.

357 3-1. Using the air conditioning system and defogger 3 Interior fe atures Air flows to the feet and thewindshield defogger operates. ■ Switching between outside air and recirculated air modes Press . The mode switches between outside air mode (introduces air from out-side the vehicle) (indicator ...

361 3-1. Using the air conditioning system and defogger 3 Interior fe atures ■ When the indicator light on flashes Press and turn off the air conditioning system before turning it on once more. There may be a problem in the air conditioning system if the indi-cator light continues to flash. Turn the...

362 3-1. Using the air conditioning system and defogger Rear manual air conditioning system ∗ Adjusting the settings ■ Adjusting the temperature setting Turn the temperature control dial clockwise (warm) or counter-clockwise (cool). ■ Adjusting the fan speed Turn the fan speed control dial clockwise...

363 3-1. Using the air conditioning system and defogger 3 Interior fe atures ■ Changing the air outlets Press the desired . Air flows as shown below according to the mode selected. Air flows to the upper body. Air flows to the upper body andfeet. Air flows to the feet.

365 3-1. Using the air conditioning system and defogger 3 Interior fe atures Rear automatic air conditioning system ∗ Using the automatic mode Press . The air conditioning system begins to operate. Air outlets and fanspeed are automatically adjusted according to the temperature set-ting. Press “ ∧ ”...

367 3-1. Using the air conditioning system and defogger 3 Interior fe atures Air flows to the feet. ■ Adjusting the fan speed Press “ ∧ ” on to increase the fan speed and “ ∨ ” to decrease the fan speed. Press to turn the fan off. Adjusting the position of the air outlets Direct air flow to the fron...

368 3-1. Using the air conditioning system and defogger ■ Temperature display The temperature display (English/U.S. Customary System and metric units)on the trip information display can be changed. ( → P. 241) ■ When the front air conditioning system is in simultaneous mode “SYNC” is shown on the di...

369 3-1. Using the air conditioning system and defogger 3 Interior fe atures Rear window and outside rear view mirror defoggers, and windshield wiper de-icer The rear window defogger is used to defog the rear window. The out-side rear view mirror defoggers * 1 are used to remove frost, dew or raindr...

370 3-1. Using the air conditioning system and defogger ■ The defogger can be operated when Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is IGNITION ON mode. ■ Outside rear view mirror defoggers (vehicl...

371 3 Interior fe atures 3-2. Using the audio system Audio system type With navigation system Owners of models equipped with a navigation system shouldrefer to the “NAVIGATION SYSTEM OWNER’S MANUAL”. Without navigation system Type A and B: CD player with AM/FM radio Type C: CD player with changer an...

373 3-2. Using the audio system 3 Interior fe atures Language settings (type B and C) The language used for all voice guidance, voice recognition and mes-sages may be changed. Press . Press that corresponds to “MORE”. Press that corresponds to “LANG”. Press that corresponds to the desired language. ...

374 3-2. Using the audio system ■ Using cellular phones Interference may be heard through the audio system’s speakers if a cellularphone is being used inside or close to the vehicle while the audio system isoperating. CAUTION ■ For vehicles sold in the U.S.A. ● Part 15 of the FCC Rules FCC Warning:A...

375 3-2. Using the audio system 3 Interior fe atures NOTICE ■ To prevent battery discharge Do not leave the audio system on longer than necessary with the engine off. ■ To avoid damaging the audio system Take care not to spill drinks or other fluids over the audio system.

376 3-2. Using the audio system Using the radio Type A Seeking the frequency Volume Power Station selector Changing the channel AM•SAT/FM mode buttons Scanning for receivable stations Displaying radio text messages Adjusting the frequency (AM, FM mode) or channel (SAT mode)

377 3-2. Using the audio system 3 Interior fe atures Type B and C Seeking the frequency Volume Power Station selector Changing the channel AM/FM/SAT mode button Scanning for receivable stations Displaying radio text messages Adjusting the frequency (AM, FM mode) or channel (SAT mode) Selecting the p...

378 3-2. Using the audio system Setting station presets (excluding XM ® Satellite Radio) Search for desired stations by turning or or pressing “ ∧ ” or “ ∨ ” on . Press and hold the button (from to or one of ) until you hear a beep. Type B and C: Each time is pressed, station pages are changed. Ther...

379 3-2. Using the audio system 3 Interior fe atures ■ Displaying radio text messages (for type B and C, FM modeonly) When a new radio text message is received, “MSG” is shown on the display. To display the message, press . If the text continues past the end of the display, “ ” is displayed. Press a...

380 3-2. Using the audio system ■ Setting XM ® Satellite Radio channel presets Select the desired channel. Press and hold a button (from to or one of ) until you hear a beep. Type B and C: Each time is pressed, station pages are changed. There is a total of 6 sets of 6 presets. ■ Changing the channe...

381 3-2. Using the audio system 3 Interior fe atures ■ Displaying text information Press . Each time is pressed, the display changes in the following order: Type A Channel name → Title (song/program title) → Name (artist name/ feature) → Channel number. Type B and C Title (song/ program title) → Tit...

383 3-2. Using the audio system 3 Interior fe atures ■ Receiving XM ® Satellite Radio An XM ® Satellite Radio is a tuner designed exclusively to receive broadcasts provided under a separate subscription. Availability is limited to the 48 con-tiguous states and 10 Canadian provinces. ● XM ® subscript...

384 3-2. Using the audio system ■ If the satellite radio does not operate normally If a problem occurs with the XM ® tuner, a message will appear on the dis- play. Refer to the table below to identify the problem, and take the suggestedcorrective action. ANTENNA or CHECK ANTENNA The XM ® antenna is ...

385 3-2. Using the audio system 3 Interior fe atures Contact the XM ® Listener Care Center at 1-800-967-2346 (U.S.A.) or 1-877- 438-9677 (Canada). ■ Certifications for the radio tuner This equipment has been tested and found to comply with the limits for aclass B digital device, pursuant to Part 15 ...

386 3-2. Using the audio system Using the CD player Type A Selecting a track Volume Power CD eject Selecting a track Playback Random playback Displaying text messages Repeat play Searching playback Fast-forward Reverse

387 3-2. Using the audio system 3 Interior fe atures Loading CDs ■ Loading a CD (type A and B) Insert a CD. ■ Loading a CD (type C) Press . Insert a CD when the indicator on the slot turns from amber togreen. Type B and C Selecting a track/fast-forwarding and reversing Volume Power Selecting a track...

388 3-2. Using the audio system ■ Loading multiple CDs (type C only) Press and hold until you hear a beep. Insert a CD when the indicator on the slot turns from amber togreen. The indicator on the slot turns to amber when the CD is inserted. Insert the next CD when the indicator on the slot turns fr...

389 3-2. Using the audio system 3 Interior fe atures Selecting a track Turn or or press “ ∧ ” or “ ∨ ” on to select the desired track. Fast forwarding and rewinding tracks Type A Press or . Type B and C Press and hold “ ∧ ” or “ ∨ ” on . Scanning tracks Press . The first 10 seconds of each track wil...

390 3-2. Using the audio system Selecting a CD (type C only) ■ Selecting a CD to play Press that corresponds to “DISC ” or “ DISC”. ■ Scanning loaded CDs Press and hold until you hear a beep. The first 10 seconds of the first track on each CD will be played. To cancel, press again. Press again when ...

391 3-2. Using the audio system 3 Interior fe atures Repeat play ■ Repeating a track Press or that corresponds to “RPT”. To cancel, press the button again. ■ Repeating all of the tracks on a CD (type C only) Press that corresponds to “RPT” twice. To cancel, press the button again. Switching the disp...

392 3-2. Using the audio system ■ Display (type A only) Up to 12 characters can be displayed at a time. If there are 13 characters or more, pressing and holding for 1 second or more will display the remaining characters.A maximum of 24 characters can be displayed. If is pressed for 1 second or more ...

393 3-2. Using the audio system 3 Interior fe atures ■ Discs that can be used Discs with the marks shown below can be used.Playback may not be possible depending on recording format or disc fea-tures, or due to scratches, dirt or deterioration. CDs with copy-protect features may not play correctly. ...

394 3-2. Using the audio system NOTICE ■ CDs and adapters that cannot be used Do not use the following types of CDs, 3 in. (8 cm) CD adapters or DualDisc. Doing so may damage the player and/or the CD insert/eject function. ● CDs that have a diameter that is not4.7 in. (12 cm). ● Low-quality and defo...

395 3-2. Using the audio system 3 Interior fe atures NOTICE ■ Player precautions Failure to follow the precautions below may result in damage to the CDs orthe player itself. ● Do not insert anything other than CDs into the CD slot. ● Do not apply oil to the CD player. ● Store CDs away from direct su...

396 3-2. Using the audio system Playing MP3 and WMA discs Type A Selecting a file Volume Power CD eject Selecting a folder Playback Displaying text messages Repeat play Fast-forwarding Reversing Searching playback Random playback Selecting a file

397 3-2. Using the audio system 3 Interior fe atures Loading and ejecting MP3 and WMA discs → P. 386 Selecting MP3 and WMA discs (type C only) → P. 386 Type B and C Selecting a file/fast-forwarding and reversing Volume Power CD eject Selecting a file CD load (type C only) Playback Displaying text me...

398 3-2. Using the audio system Selecting and scanning a folder ■ Selecting folders one at a time Press “ ∧ ” or “ ∨ ” on to select the desired folder. ■ Scanning the first file of all the folders Press and hold until you hear a beep. The first 10 seconds of the first file in each folder will be pla...

401 3-2. Using the audio system 3 Interior fe atures ■ Display (type A only) → P. 392 ■ Error messages “CD CHECK”: This indicates a problem either with the CD or inside the player. The CD may be dirty, damaged or inserted up-sidedown. “WAIT” or “PLEASE WAIT”: Operation has stopped due to a high temp...

404 3-2. Using the audio system ● MP3 and WMA playback When a disc containing MP3 or WMA files is inserted, all files on the discare first checked. Once the file check is finished, the first MP3 or WMA fileis played. To make the file check finish more quickly, we recommend youdo not write in any fil...

405 3-2. Using the audio system 3 Interior fe atures Operating an iPod ® ∗ ∗ : If equipped Connecting an iPod ® enables you to enjoy music from the vehicle speakers. ■ Connecting an iPod ® Open the cover and connectan iPod ® using an iPod ® cable. Press . ■ Control panel STEP 1 STEP 2 Fast-forwardin...

407 3-2. Using the audio system 3 Interior fe atures ■ Selecting a list Turn to display the first selection list. Press to select the desired item. Pressing that corresponds to “MORE” changes to the second selection list. Repeat the same procedure to select the desired song name. To return to the pr...

409 3-2. Using the audio system 3 Interior fe atures Switching the display Press . Each time the button is pressed, the display changes in the followingorder: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed ■ About iPod ® ● “Made for iPod” means that an electroni...

411 3-2. Using the audio system 3 Interior fe atures CAUTION ■ While driving Do not connect iPod ® or operate the controls on the iPod ® . NOTICE ■ To prevent damage to iPod ® ● Do not leave iPod ® in the vehicle. The temperature inside the vehicle may become high, resulting in damage to the player....

412 3-2. Using the audio system Operating a USB memory ∗ ∗ : If equipped Connecting a USB memory enables you to enjoy music from thevehicle speakers. ■ Connecting a USB memory Open the cover and connect aUSB memory. Press . ■ Control panel STEP 1 STEP 2 Fast-forwarding and reversing/Selecting a song...

415 3-2. Using the audio system 3 Interior fe atures Switching the display Press . Each time the button is pressed, the display changes in the followingorder: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time ■ USB memory functions Depending on the USB memory ...

416 3-2. Using the audio system ■ USB memory ● Compatible devices USB memory that can be used for MP3 and WMA playback Depending on the type of USB device, playback may not be possible. ● Compatible device formats The following device formats can be used: • USB communication formats: USB2.0 FS (12mb...

419 3-2. Using the audio system 3 Interior fe atures CAUTION ■ While driving Do not connect USB memory or operate the controls on the USB memory. NOTICE ■ To prevent damage to USB memory ● Do not leave USB memory in the vehicle. The temperature inside the vehi-cle may become high, resulting in damag...

420 3-2. Using the audio system Optimal use of the audio system Type A Type B and C Adjusting the sound quality and ASL Selector knob Selector buttons Menu button

421 3-2. Using the audio system 3 Interior fe atures Using the audio control function ■ Changing sound quality modesType A Pressing selects the mode in the following order. “BAS” → “TRE” → “FAD” → “BAL” → “ASL” Type B and C Press . Press that corresponds to the desired mode. “BASS”, “MID” (type C on...

422 3-2. Using the audio system ■ Adjusting sound quality Turning or adjusts the level. * 1 :The sound quality level is adjusted individually in each audio mode. * 2 :Type C only Sound quality mode Mode displayed Level Turn to the left Turn to the right Low-pitched tones * 1 BAS -5 to 5 Low High Mid...

424 3-2. Using the audio system ■ Setting the number of preset pages (type B and C) The number of preset pages desired can be set from 1 to 6. Theinitial setting is 6 pages. Press . Press that corresponds to “MORE”. Press that corresponds to “PRESET”. Press that corresponds to the desired number of ...

425 3-2. Using the audio system 3 Interior fe atures Using the AUX adapter ■ Operating portable audio devices connected to the audio system The volume can be adjusted using the vehicle’s audio controls. All otheradjustments must be made on the portable audio device itself. ■ When using a portable au...

426 3-2. Using the audio system Using the steering switches Some audio features can be controlled using the switches on thesteering wheel. VolumePower on, select audiosourceRadio mode: Selects a radio station CD mode: Selects a track, file (MP3and WMA) anddisc Bluetooth ® audio mode: Selects a track...

427 3-2. Using the audio system 3 Interior fe atures Turning on the power Press when the audio system is turned off. The audio system can be turned off by holding the switch down until youhear a beep. Changing the audio source Press when the audio system is turned on. The audio source changes as fol...

429 3-2. Using the audio system 3 Interior fe atures Selecting a disc in the CD changer (type C only) Press to select the CD mode. Press and hold “ ∧ ” or “ ∨ ” on until you hear a beep. Selecting a track/file or chapter (vehicles with rear seatentertainment system) Press to select the RSE mode. Pre...

430 3-3. Using the Bluetooth ® audio system Bluetooth ® audio system ∗ ■ Conditions under which the system will not operate ● If using a portable player that does not support Bluetooth ® ● If the portable player is switched off ● If the portable player is not connected ● If the portable player’s bat...

431 3-3. Using the Bluetooth ® audio system 3 Interior fe atures ■ When transferring ownership of the vehicle Be sure to initialize the system to prevent personal data from being improp-erly accessed. ( → P. 516) ■ About Bluetooth ® ■ Compatible models ● Bluetooth ® specifications: Ver. 1.2, or high...

432 3-3. Using the Bluetooth ® audio system CAUTION ■ FCC WARNING Changes or modifications not expressly approved by the party responsiblefor compliance could void the user’s authority to operate the equipment. Radio Frequency Radiation Exposure. This equipment complies with FCC/IC radiation exposur...

433 3-3. Using the Bluetooth ® audio system 3 Interior fe atures Using the Bluetooth ® audio system ■ Audio unit Display A message, name, number,etc. is displayed. Lower-case charactersand special characterscannot be displayed. Selects items such as menuand numberTurn: Selects an itemPress: Inputs t...

434 3-3. Using the Bluetooth ® audio system Operating the system using voice commands By following voice guidance instructions output from the speaker,voice commands enable to the operation of the Bluetooth ® audio sys- tem without the need to check the display or operate . ■ Operation procedure whe...

436 3-3. Using the Bluetooth ® audio system Select “Confirm” using a voice command or . A passkey is displayed and heard, and a voice guidance instructionfor inputting the passkey into the portable player is heard. Input the passkey into the portable player. Refer to the manual that comes with the p...

437 3-3. Using the Bluetooth ® audio system 3 Interior fe atures Menu list of the Bluetooth ® audio system ■ Normal operation “BT • A Setup” can be canceled by pressing the on-hook switch or saying the voice command, “Cancel”. * : Selection of system set-up is possible only by the operation of the s...

438 3-3. Using the Bluetooth ® audio system ■ When using a voice command For numbers, say a combination of single digits from zero to nine. Say the command correctly and clearly. ■ Situations in which the system may not recognize your voice ● When driving on rough roads ● When driving at high speeds...

439 3-3. Using the Bluetooth ® audio system 3 Interior fe atures Operating a Bluetooth ® enabled portable player Selecting an album Press “ ∧ ” or “ ∨ ” on . Selecting tracks Press “ ∧ ” or “ ∨ ” on to select the desired track. Volume Power Displaying text messages Selecting an album Selector button...

440 3-3. Using the Bluetooth ® audio system Playing and pausing tracks Press . Fast-forwarding and rewinding tracks Press and hold “ ∧ ” or “ ∨ ” on . Switching the display Press . Each time the button is pressed, the display changes in the followingorder: Track title → Track title/Artist name → Tra...

441 3-3. Using the Bluetooth ® audio system 3 Interior fe atures Setting up a Bluetooth ® enabled portable player Registering a portable player in the Bluetooth ® audio system allows the system to function. The following functions can be used for reg-istered portable players: ■ Functions and operati...

442 3-3. Using the Bluetooth ® audio system Registering a portable player Select “Pair Audio Player” using a voice command or , and perform the procedure for registering a portable player. ( → P. 435) Selecting a portable player to be used Select “Select Audio Player” using a voice command or . Sele...

443 3-3. Using the Bluetooth ® audio system 3 Interior fe atures Vehicles without a smart key system When the portable player is on standby for the connection, it will beautomatically connected whenever the engine switch is in either“ACC” or “ON” position. If a portable player that has already been ...

444 3-3. Using the Bluetooth ® audio system Listing the registered portable players Select “List Audio Players” using a voice command or . The list of registered portable players will be read aloud.When listing is complete, the system returns to “BT•A Setup”. Pressing the talk switch while the name ...

445 3-3. Using the Bluetooth ® audio system 3 Interior fe atures Deleting a registered portable player Select “Delete Audio Player” using a voice command or . Select the portable player to be deleted by either of the follow-ing methods and select “Confirm” using a voice command or : a. Press the tal...

446 3-3. Using the Bluetooth ® audio system Bluetooth ® audio system setup ■ System setup items and operation procedures → P. 512

447 3 Interior fe atures 3-4. Using the rear audio system Rear seat entertainment system features ∗ ∗ : If equipped The rear seat entertainment system is designed to allow the rear pas-sengers to enjoy audio and DVD video separately from the frontaudio system. Front audio systemDVD playerDisplayHead...

448 3-4. Using the rear audio system Opening and closing the display ■ Opening and closing the display Press the lock release button toopen the display. Pull the display down to an easilyviewable angle (at 100 ° or 120 ° ). To close the display, push thedisplay up until a click is heard. The illumin...

449 3-4. Using the rear audio system 3 Interior fe atures Loading a disc Open the cover. Insert the disc into the slot withthe label side up. The “DISC” indicator light turnson while the disc is loaded. The player will play the track orchapter, and will repeat it after itreaches the end. Close the c...

450 3-4. Using the rear audio system Turning the rear seat entertainment system power on/off ■ Operating from the front audio system Selecting either the front audiosystem or DVD player audiofor the speakers Press that corresponds to “OFF”, to turn off the rearseat entertainment system. Press that c...

451 3-4. Using the rear audio system 3 Interior fe atures Setting the rear seat entertainment system lock Vehicles with a navigation system Owners of models equipped with a navigation system should referto the “NAVIGATION SYSTEM OWNER’S MANUAL”. Vehicles without a navigation systemFront audio system...

453 3-4. Using the rear audio system 3 Interior fe atures ■ Turning off the screen Press on the remote con- troller. Press the “Screen off” displayedon the screen. Press , , or to turn on the screen. Headphone jacks To use the headphones, con-nect them to the jack.To adjust the volumeTurn the knob c...

455 3-4. Using the rear audio system 3 Interior fe atures ■ Headphone audio during split screen display Audio from the left-hand screen will be played through the left headphone,and audio from the right-hand screen will be played through the right head-phone. ■ Error messages Message Cause Correctio...

456 3-4. Using the rear audio system ■ Before using the remote controller (for new vehicle owners) ■ When the remote controller batteries are fully depleted ■ If the remote controller batteries are discharged The following symptoms may occur. ● The rear seat entertainment system control will not fun...

457 3-4. Using the rear audio system 3 Interior fe atures ■ Headphones With some headphones generally available on the market, it may be difficultto receive signals properly. Toyota recommends the use of Toyota genuinewireless headphones. Please contact your Toyota dealer for further details. ■ Volu...

458 3-4. Using the rear audio system NOTICE ■ For normal operation after replacing the battery Observe the following precautions to prevent accidents. ● Always work with dry hands.Moisture may cause the battery to rust. ● Do not touch or move any other components inside the remote controller. ● Do n...

459 3-4. Using the rear audio system 3 Interior fe atures Using the DVD player (DVD video) ■ Remote controller Turning on or off the rearentertainment screenTurning on the DVD modeSelecting a chapterTurning on the title selectionscreenReversing a discPlaying/pausing a discTurning on or off the opera...

461 3-4. Using the rear audio system 3 Interior fe atures NOTICE ■ Cleaning the display Wipe the display with a dry soft cloth.If the screen is wiped with a rough cloth, the surface of the screen may bescratched. ■ Display (Page 2) Displaying the initial settingscreenDisplaying page 1Search for a ti...

462 3-4. Using the rear audio system Turning on or off the operation switches Press to turn on the operation switches. Press once again or select to turn off the operation switches. Turning on the title selection screen Press or select to turn on the title selection screen. For the operation of the ...

463 3-4. Using the rear audio system 3 Interior fe atures Slow playback Press or select to pause video and then press or select . Video is played slowly when you press or select by pressing and holding . Returning to the previous screen Select to return to the previous screen. For the operation of t...

465 3-4. Using the rear audio system 3 Interior fe atures Changing the angle Select on the control icon screen. Select to display the screen to change the angle. Each time you press , the next available angle isselected. : returns to the previous screen STEP 1 STEP 2 ■ DVD player and DVD video discs...

466 3-4. Using the rear audio system ■ Marks shown on DVD video discs ■ DVD video disc glossary ● DVD video discs: Digital Versatile Discs that hold world’s standard video.DVD video discs have adopted “MPEG2”, one of the world standards ofdigital compression technologies. The picture data is compres...

470 3-4. Using the rear audio system Selecting a desired screen ■ Selecting a menu number Select on the control icon screen. Input the desired menu number and select . : deletes the last input num- ber : returns to the previous screen ■ Searching manually Select or on the screen, or press or until t...

471 3-4. Using the rear audio system 3 Interior fe atures Changing the sound-multiplex mode Select on the control icon screen. The mode cycles through each time the is pressed. “Main” → “Sub” → “Main/Sub” Slow playback Press or select to pause video and then press or select . Video is played slowly ...

472 3-4. Using the rear audio system Using the DVD player (audio CD/CD text) ■ Canceling random, repeat and scan play Select , or again. Press to display the control screen. Repeat playRandom playbackSearch playback ■ Front audio system Press: Selecting a chapter Press and hold: Fast-for-warding/rev...

473 3-4. Using the rear audio system 3 Interior fe atures Using the DVD player (WMA/MP3 discs) Repeat play ■ Repeating a file Select . ■ Repeating all of the files in a folder Select , and press and hold . ■ Using the control screen Press to display the control screen. Repeat playRandom playbackSear...

474 3-4. Using the rear audio system Random playback ■ Playing files from a particular folder in random order Select . ■ Playing all of the files on a disc in random order Select , and press and hold . Search playback ■ Selecting the desired file by cueing the files in the folder Select . The player...

475 3-4. Using the rear audio system 3 Interior fe atures Using the video mode Using the adapter Type A Open the cover. The A/V input adapter is com-posed of 3 input adapters. Yellow: Image input adapter White: Left channel audio inputadapter Red: Right channel audio inputadapter Type B Press to sel...

476 3-4. Using the rear audio system ■ A/V input adapter The rear seat entertainment system plays video and sound when an audio-video device is connected to the A/V input adapter. For details, refer to themanufacturer’s instructions. ■ Power outlet The power outlet is used to connect the audio devic...

477 3-4. Using the rear audio system 3 Interior fe atures Changing the DVD initial setting Select to display the initial setting screen. The following initialization canbe changed here. ● Audio language ● Subtitle language ● DVD language ● Angle mark ● Parental lock

478 3-4. Using the rear audio system Changing the audio language Select “Audio Language”. Select the language you want to hear, and press to input it. : returns to the previous screen Select “Others” if you cannot findthe language you want to hear.Enter the appropriate 4-digit lan-guage code. ( → P....

479 3-4. Using the rear audio system 3 Interior fe atures Changing the subtitle language Select “Subtitle Language”. Select the language you want to read, and press to input it. : returns to the previous screen Select “Others” if you cannot findthe language you want to read.Enter the appropriate 4-d...

480 3-4. Using the rear audio system Changing the DVD language Select “DVD Language”. Select the language you want to read, and press to input it. : returns to the previous screen Select “Others” if you cannot findthe language you want to read.Enter the appropriate 4-digit lan-guage code. ( → P. 485...

481 3-4. Using the rear audio system 3 Interior fe atures Turning on or off the angle mark The angle mark can be turned on for discs that are multi-angle com-patible. Each time you press when “Angle Mark” is selected, the angle mark turns on or off alternately.

482 3-4. Using the rear audio system Setting viewer restriction levels Setting a password allows the viewer restriction to be effective. Input the desired personal code and select . : deletes the last input number : returns to the previous screen The setting cannot be changedunless the password is e...

483 3-4. Using the rear audio system 3 Interior fe atures Setting the display mode ■ Display size Single screen mode: Pressing changes the display modes sequentially asfollows: Normal → Wide → Super wide → Ultra wide → Ultra zoom Split screen mode: Pressing changes the display mode sequentially as f...

484 3-4. Using the rear audio system ■ Returning to the previous screen Select and press . ■ To initialize the password Press on the remote controller or unit ten times when the screen to enter the personal code is displayed. ■ When changing the display size ● When using this product, you can select...

485 3-4. Using the rear audio system 3 Interior fe atures ■ Language code list Code Language 0514 English 0618 French 0405 German 0920 Italian 0519 Spanish 2608 Chinese 1412 Dutch 1620 Portuguese 1922 Swedish 1821 Russian 1115 Korean 0512 Greek 0101 Afar 0102 Abkhazian 0106 Afrikaans 0113 Amharic 01...

491 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures ■ About Bluetooth ® ■ Compatible models Compatible with HFP (Hands Free Profile) Ver. 1.5 and OPP (Object PushProfile) Ver. 1.1. If your cellular phone does not support HFP, you cannot enter the Bluetooth ® phone. I...

492 3-5. Using the hands-free phone system (for cellular phone) CAUTION ■ FCC WARNING Changes or modifications not expressly approved by the party responsiblefor compliance could void the user’s authority to operate the equipment. Radio Frequency Radiation Exposure. This equipment complies with FCC/...

493 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Using the hands-free phone system (for cellular phone) ∗ ∗ : If equipped ■ Audio unit Displays such items asmessages, name, andphone number Lower-case characters andspecial characters, such asan umlaut, cannot be di...

494 3-5. Using the hands-free phone system (for cellular phone) ■ Steering wheel telephone switches Volume The voice guidance volumecannot be adjusted usingthis button. Hands-free phone systemoff/ends a call/refuses a callHands-free phone systemon/starts a callPress: Voice command sys-tem onPress an...

495 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Operating the system using a voice command By following voice guidance instructions output from the speaker,voice commands can be given to allow for operation of the hands- free phone system without checking the dis...

496 3-5. Using the hands-free phone system (for cellular phone) Using the hands-free phone system for the first time Before using the hands-free phone system, it is necessary to registera cellular phone in the system. The phone registration mode will beentered automatically when starting the system ...

497 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Registration to the hands-free phone system only Select “Phone Only” using a voice command or . Registration to the hands-free phone system and Bluetooth ® audio system at the same time Select “Internal Audio (Int, ...

500 3-5. Using the hands-free phone system (for cellular phone) ■ Using a short cut key First menu Second menu Operation detail “Dial XXX (name)” - Dialing a number registered in the phone book “Dial XXX (number)” - Dialing the input numbers “Phone book add entry” - Adding a new number “Phone book c...

501 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures ■ Automatic adjustment of volume When vehicle speed is 50 mph (80 km/h) or more, the volume automaticallyincreases. The volume returns to the previous volume setting when vehiclespeed drops to 43 mph (70 km/h) or le...

502 3-5. Using the hands-free phone system (for cellular phone) Making a phone call ■ Making a phone call ● Dialing by inputting a number“Dial by number” ● Dialing by inputting a name“Dial by name” ● Speed dialing ● Dialing a number stored in the outgoing history memory“Redial” ● Dialing a number st...

503 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Dialing by inputting a number Press the talk switch and say “Dial by number”. Press the talk switch and say the phone number.Dial by one of the following methods:a. Press the off- hook switch.b. Press the talk switc...

504 3-5. Using the hands-free phone system (for cellular phone) Speed dialing Press the off-hook switch.Press the preset button in which the desired number is regis-tered.Press the off-hook switch. When receiving a phone call ■ Answering the phone Press the off-hook switch. ■ Refusing the call Press...

505 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Using the call history memory Follow the procedure below to use a number stored in the call historymemory: Press the talk switch and say “Redial” (when using a numberstored in the outgoing call history memory) or “C...

506 3-5. Using the hands-free phone system (for cellular phone) ■ Call history Up to 5 phone numbers can be stored in each of the outgoing and incomingcall history memories. ■ When talking on the phone ● Do not talk simultaneously with the other party. ● Keep the volume of the received voice down. O...

507 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Setting a cellular phone Registering a cellular phone in the hands-free phone system allowsthe system to function. The following functions can be used for reg-istered cellular phones: ■ Functions and operation proce...

508 3-5. Using the hands-free phone system (for cellular phone) Registering a cellular phone Select “Pair Phone” using a voice command or , and do the procedure for registering a cellular phone. ( → P. 496) Selecting the cellular phone to be used Select “Select Phone” using a voice command or . Patt...

509 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Changing a registered name Select “Change Name” using a voice command or . Select the name of the cellular phone to be changed by one ofthe following methods:a. Press the talk switch and say the desired phone name, ...

510 3-5. Using the hands-free phone system (for cellular phone) Listing the registered cellular phones Selecting “List Phones” using a voice command or causes the list of registered cellular phones to be read aloud.When listing is complete, the system returns to “Phone Setup”. Pressing the talk swit...

511 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Changing the passkey Select “Set Passkey” using a voice command or . Press the talk switch, say a 4 to 8-digit number, and select “Confirm” using a voice command or . The number should be input 1 digit at a time. Wh...

512 3-5. Using the hands-free phone system (for cellular phone) Security and system setup To enter the menu of each setting, follow the steps below: ■ Security setting items and operation procedure ● Setting or changing the PIN (Personal Identification Number) 1. “Setup” → 2. “Security” → 3. “Set PI...

513 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Setting or changing the PIN ■ Setting a PIN Select “Set PIN” using a voice command or . Enter a PIN using a voice command or . When using , input the code 1 digit at a time. ■ Changing the PIN Select “Set PIN” using...

514 3-5. Using the hands-free phone system (for cellular phone) Locking or unlocking the phone book Select “Phonebook Lock (Phbk Lock)” or “Phonebook unlock (Phbk Unlock)” using a voice command or . Input the PIN by either of the following methods and select “Confirm” using a voice command or : a. P...

515 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Displaying the Bluetooth ® device address and name Select “Device Name” using . Turn to display the Bluetooth ® device address and name. Select “Go Back” using to return to “System Setup”. Initialization Select “Ini...

517 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Using the phone book Adding a new phone number The following methods can be used to add a new phone number: ● Inputting a phone number using a voice command ● Transferring data from the cellular phone ● Inputting a ...

519 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Inputting a phone number using STEP2-1: Select “Manual Input” using . STEP2-2: Input a phone number using , and press once again. Input the phone number 1 digit at a time. Selecting a phone number from outgoing or i...

520 3-5. Using the hands-free phone system (for cellular phone) Select the name to be registered by either of the followingmethods, and select “Confirm” using a voice command or : a. Press the talk switch and say the desired name. b. Select “Record Name” using , and say the desired name. Select “Con...

523 3-5. Using the hands-free phone system (for cellular phone) 3 Interior fe atures Listing the registered data Selecting “List names” using a voice command causes a list of theregistered data to be read aloud. When listing is complete, the system returns to “Phonebook”.Pressing the talk switch whi...

524 3-6. Using the interior lights Interior lights list Outer foot lights (if equipped)Rear interior lightRear personal/interior lights ( → P. 526) Rear ceiling lights ( → P. 527) Front personal/interior lights ( → P. 526) Engine switch light (if equipped)Front door courtesy lights (if equipped)

525 3-6. Using the interior lights 3 Interior fe atures Personal/interior light main switch (vehicles with overheadconsole) Type A On The personal/interior lights can-not be individually turned off. Door position The personal/interior lights andrear interior light come on when adoor is opened. They ...

526 3-6. Using the interior lights Personal/interior lights (vehicles with overhead console) Front type A On/off Front type B Rear On/off Rear personal/interior lights turnon when the personal/interiormain switch is in door position. Personal/interior lights

527 3-6. Using the interior lights 3 Interior fe atures Personal lights (vehicles without overhead console) Front On/off Rear On/off Rear ceiling lights (if equipped) On/off Personal lights and rear ceiling lights

528 3-6. Using the interior lights ■ Adjusting the rear personal/interior lights angle ■ Illuminated entry system (if equipped) Vehicles without a smart key system The lights automatically turn on/off according to the engine switch position,whether the doors are locked/ unlocked, and whether the doo...

529 3-6. Using the interior lights 3 Interior fe atures NOTICE ■ Rear ceiling lights Do not hang anything on the gap between the ceiling light cover and the ceil-ing or pull the ceiling light cover strongly. Doing so may cause damage.

530 3-7. Using the storage features List of storage features Auxiliary boxesCup holdersBottle holdersOverhead console (if equipped)Glove boxConsole box (if equipped)

531 3-7. Using the storage features 3 Interior fe atures CAUTION ■ Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as thismay cause the following when cabin temperature becomes high: ● Glasses may be deformed by heat or cracked ...

532 3-7. Using the storage features Glove boxes Upper glove box Push the button. Lower glove box The lower glove box can be opened by pulling the lever and can belocked and unlocked by using the master key (vehicles without asmart key) or the mechanical key (vehicles with a smart key system). Unlock...

533 3-7. Using the storage features 3 Interior fe atures ■ Removing the separate tray (upper glove box) CAUTION ■ Caution while driving Keep the glove box closed when not in use. In the event of sudden braking,an accident may occur due to an occupant being struck by the open glovebox or the items st...

534 3-7. Using the storage features Console box (if equipped) ■ Using the console box Type A Press the tab. Type B Press the tab. Console box

535 3-7. Using the storage features 3 Interior fe atures ■ Sliding the console box (type B) From front From rear ■ Console box light The console box light turns on when the headlight switch is on. Press the tab and slide the console box. Pull up the lever and slide the consolebox. Console box

537 3-7. Using the storage features 3 Interior fe atures Overhead console (if equipped) Push the lid. The overhead console is usefulfor temporarily storing smallitems. CAUTION ■ While driving Do not leave the overhead console open. Items may fall out and cause injury. ■ Maximum storage weight Do not...

540 3-7. Using the storage features ■ Removing the separator (front) ■ Cup holder light (console box type A and B) The cup holder light turns on when the headlight switch is on. CAUTION ■ Items unsuitable for the cup holder Do not place anything other than cups or aluminum cans in the cup holders.Ot...

542 3-7. Using the storage features CAUTION ■ Items unsuitable for the bottle holder Do not place anything other than a bottle in the bottle holders.Other items may be thrown out of the holders in the event of an accident orsudden braking and cause injury. NOTICE ■ When stowing a bottle Put the cap ...

543 3-7. Using the storage features 3 Interior fe atures Auxiliary boxes Type A Push down the knob. Type B (if equipped) Type C Auxiliary boxes

544 3-7. Using the storage features Type D (if equipped) Type E (if equipped) Type F Lift the lid. Auxiliary boxes

545 3-7. Using the storage features 3 Interior fe atures Type G Removing the second centerseat. ( → P. 100) Type H (if equipped) Type I (if equipped) ITN37N026 ITN37N027 Auxiliary boxes

548 3-8. Other interior features Sun visors To set the visor in the for-ward position, flip it down.To set the visor in the sideposition, flip down, unhook,and swing it to the side.To use the side extender,place the visor in the sideposition, then slide it back-ward.

549 3-8. Other interior features 3 Interior fe atures Vanity mirrors NOTICE ■ To prevent battery discharge Do not leave the vanity lights on for extended periods while the engine is off. Flip down.Open the cover. The light turns on when thecover is opened.

550 3-8. Other interior features Clock ∗ ■ The clock is displayed when Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ONmode. ■ When disconnecting and reconnecting bat...

551 3-8. Other interior features 3 Interior fe atures Conversation mirror ∗ ∗ : If equipped The conversation mirror can provide the driver and the front passen-ger with a view of the rear seat area without the need to turn around. Push the lid and allow the lidto open. Push the lid. To first lockedp...

552 3-8. Other interior features Power outlets The power outlet can be used for the following components: 12 V: Accessories that run on less than 10 A 120 V AC: Accessories that use less than 100 W ■ 12 V Center panel type A Center panel type B

553 3-8. Other interior features 3 Interior fe atures Luggage compartment ■ 120 V AC (if equipped) Power outlet socket console box type A Power outlet socket console box type B

554 3-8. Other interior features ■ The power outlet can be used when Vehicles without a smart key system 12 V: The engine switch is in the “ACC” or “ON” position. 120 V AC: The engine switch is in the “ON” position. Vehicles with a smart key system 12 V: The “ENGINE START STOP” switch is in ACCESSOR...

555 3-8. Other interior features 3 Interior fe atures NOTICE ■ To avoid damaging the power outlet Close the power outlet lid when the power outlet is not in use.Foreign objects or liquids that enter the power outlet may cause a short cir-cuit. ■ To prevent blown fuse 12 V Do not use an accessory tha...

556 3-8. Other interior features Seat heaters ∗ ■ The seat heaters can be used when Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. ■ When not in use Move the dial fully downward. T...

557 3-8. Other interior features 3 Interior fe atures CAUTION ■ Burns ● Use caution when seating the following persons in a seat with the seatheater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the physically chal- lenged • Persons with sensitive skin• Pe...

558 3-8. Other interior features Armrests Front seat Pull the armrest down for use. Second seat (if equipped) Pull the armrest down for use.

559 3-8. Other interior features 3 Interior fe atures ■ Adjusting the armrests (if equipped) NOTICE ■ To prevent damage to the armrest Do not place too much strain on the armrest. Push the armrest down while pressingthe button.

560 3-8. Other interior features Rear side sunshades ∗ NOTICE ■ To ensure normal operation of the sunshade Observe the following precautions. ● Do not place anything where it may hinder the opening/closing of the sun-shade. ● Do not place anything on the sunshade. ∗ : If equipped Rear door window Pu...

561 3-8. Other interior features 3 Interior fe atures Grocery bag hooks The hooks are designed to hang things like a grocery bag. Type A (front seatback) (if equipped) Type B (third seat) Type C (luggage compartment) Pull the hook up.

562 3-8. Other interior features CAUTION ■ When not in use (type C) Keep the grocery bag hook stowed.Injuries may result in the event of an accident or sudden braking. NOTICE ■ Grocery bag hook weight capacity (type A and B) Do not hang any object heavier than 8.8 lb. (4 kg) on the grocery bag hook....

563 3-8. Other interior features 3 Interior fe atures Floor mat CAUTION Observe the following precautions. Failure to do so may cause the driver’s floor mat to slip, possibly interferingwith the pedals while driving. An unexpectedly high speed may result or it maybecome difficult to stop the vehicle...

565 3-8. Other interior features 3 Interior fe atures Luggage compartment features ■ Cargo hooks Cargo hooks are provided forsecuring loose items. ■ Cargo net hooks Pattern 1 Pattern 2

566 3-8. Other interior features CAUTION ■ When the cargo hooks are not in use To avoid injury, always return the cargo hooks to their positions when theyare not in use. NOTICE ■ To prevent damage to the cargo net hooks Avoid hanging things other than a cargo net on them. ■ Storage box (if equipped)...

567 3-8. Other interior features 3 Interior fe atures Garage door opener ∗ The garage door opener (HomeLink ® Universal Transceiver) is manufac- tured under license from HomeLink ® . Programming the HomeLink ® (for U.S.A. owners) The HomeLink ® compatible transceiver in your vehicle has 3 buttons wh...

568 3-8. Other interior features Press and hold one of theHomeLink ® buttons and the transmitter button. When theHomeLink ® indicator light changes from a slow to a rapidflash, you can release both but-tons. If the HomeLink ® indicator light comes on but does not flash, orflashes rapidly for 2 secon...

569 3-8. Other interior features 3 Interior fe atures ■ Programming a Rolling Code system (for U.S.A. owners) If your device is Rolling Code equipped, follow the steps under theheading “Programming the HomeLink ® ” before proceeding with the steps listed below. Locate the training button on the ceil...

570 3-8. Other interior features Test the operation of the HomeLink ® by pressing the newly programmed button. Check to see if the gate/device operatescorrectly.Repeat the steps above to program another device for each ofthe remaining HomeLink ® buttons. ■ Programming other devices To program other ...

571 3-8. Other interior features 3 Interior fe atures Erasing the entire HomeLink ® memory (all three programs) Press and hold down the 2 out-side buttons for 10 seconds untilthe indicator light flashes. If you sell your vehicle, be sure toerase the programs stored in theHomeLink ® memory. ■ Before ...

572 3-8. Other interior features ■ For additional programming assistance with your HomeLink ® Univer- sal Transceiver Visit on the web at www.homelink.com or call 1-800-355-3515. CAUTION ■ When programming a garage door or other remote control device The garage door may operate, so ensure people and...

573 3-8. Other interior features 3 Interior fe atures Compass ∗ ∗ : If equipped The compass on the trip information display indicates the directionin which the vehicle is heading. ■ Operation To turn the compass on or off,press the switch. ■ Displays and directions Display Direction N North NE North...

574 3-8. Other interior features Calibrating the compass The direction display deviates from the true direction determined bythe earth’s magnetic field. The amount of deviation varies accordingto the geographic position of the vehicle. If you cross over a map boundary shown in illustration, the comp...

575 3-8. Other interior features 3 Interior fe atures ■ Deviation calibration Stop the vehicle where it is safe to drive in a circle. Press and hold the switch. A number (1 to 15) appears onthe compass display. Referring to the map above, press the switch to select thenumber of the zone you are in. ...

576 3-8. Other interior features ■ Conditions unfavorable to correct operation The compass may not show the correct direction in the following conditions: ● The vehicle is stopped immediately after turning. ● The vehicle is on an inclined surface. ● The vehicle is in a place where the earth’s magnet...

577 3-8. Other interior features 3 Interior fe atures NOTICE ■ To avoid a compass malfunctions Do not place magnets or any metal objects near the roof of the vehicle. Doing this may cause a malfunction of the compass sensor. ■ To ensure normal operation of the compass ● Do not perform circling calib...

578 3-8. Other interior features Safety Connect ∗ ∗ : If equipped Safety Connect is a subscription-based telematics service that usesGlobal Positioning System (GPS) data and embedded cellular tech-nology to provide safety and security features to subscribers. SafetyConnect is supported by Toyota’s d...

579 3-8. Other interior features 3 Interior fe atures ■ Services Subscribers have the following Safety Connect services avail-able: ● Automatic Collision Notification * Helps drivers receive necessary response from emergencyservice providers. ( → P. 581) * : U.S. Patent No. 7,508,298 B2 ● Stolen Veh...

580 3-8. Other interior features ■ Safety Connect Services Information ● Phone calls using the vehicles Bluetooth ® technology will not be possible during Safety Connect. ● Safety Connect is available beginning Fall 2009 on select Toyota models.Contact with the Safety Connect response center is depe...

581 3-8. Other interior features 3 Interior fe atures Safety Connect LED light Indicators When the engine switch is turned to the “ON” position (vehicles with-out a smart key system) or the “ENGINE START STOP” switch isturned to IGNITION ON mode (vehicles with a smart key system), thered indicator l...

583 3-8. Other interior features 3 Interior fe atures Safety information for Safety Connect Important! Read this information before using Safety Connect. ■ Exposure to radio frequency signals The Safety Connect system installed in your vehicle is a low-powerradio transmitter and receiver. It receive...

586 4-1. Maintenance and care Cleaning and protecting the vehicle exterior ■ Automatic car washes ● Before washing the vehicle: • Fold the mirrors.• Turn off the power back door system. (if equipped)• Turn off the power sliding door system. (if equipped) Make sure to re-install the antenna and exten...

587 4-1. Maintenance and care 4 Mainten ance an d ca re ■ Aluminum wheels ● Remove any dirt immediately by using a neutral detergent. Do not usehard brushes or abrasive cleaners. Do not use strong or harsh chemicalcleaners. Use the same mild detergent and wax as used on the paint. ● Do not use deter...

588 4-1. Maintenance and care CAUTION ■ When washing the vehicle Do not apply water to the inside of the engine compartment. Doing so maycause the electrical components etc. to catch fire. ■ Precautions regarding the exhaust pipe Exhaust gasses cause the exhaust pipe to become quite hot. When washin...

589 4-1. Maintenance and care 4 Mainten ance an d ca re NOTICE ■ Cleaning the exterior lights ● Wash carefully. Do not use organic substances or scrub with a hard brush. This may damage the surface of the lights. ● Do not apply wax on the surfaces of the lights.Wax may cause damage to the lenses. ■ ...

590 4-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle’s interior andkeep it in top condition: ■ Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty sur-faces with a cloth dampened with lu...

591 4-1. Maintenance and care 4 Mainten ance an d ca re ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a yearto maintain the quality of the vehicle’s interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use...

592 4-1. Maintenance and care NOTICE ■ Cleaning detergents ● Do not use the following types of detergent, as they may discolor the vehi-cle interior or cause streaks or damage to painted surfaces: • Non-seat portions: Organic substances such as benzene or gasoline, alkaline or acidic solutions, dye,...

601 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Items Parts and tools Engine oil level (→ P. 610) • “Toyota Genuine Motor Oil” or equivalent • Rag or paper towel• Funnel (used only for adding engine oil) Fuses ( → P. 648) • Fuse with same amperage rating as original Light bulbs ( → P. ...

602 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that maymove suddenly, become hot, or become electrically energized. To avoid deathor serious injury, observe the following precautions: ■ When working on the engine compartment: ● Keep hands, clot...

603 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re NOTICE ■ If you remove the air cleaner filter Driving with the air cleaner filter removed may cause excessive engine weardue to dirt in the air. Also a backfire could cause a fire in the engine compart-ment.

604 4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood release lever. The hood will pop up slightly. Pull up the auxiliary catchlever and lift the hood. Hold the hood open by insert-ing the supporting rod into theslot. STEP 1 STEP 2 S...

605 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re CAUTION ■ Pre-driving check Check that the hood is fully closed and locked.If the hood is not locked properly, it may open while the vehicle is in motionand cause an accident, which may result in death or serious injury. ■ After installin...

606 4-3. Do-it-yourself maintenance Positioning a floor jack When raising your vehicle with a floor jack, position the jack cor-rectly. Improper placement may damage your vehicle or cause injury. ■ Front ■ Rear 2WD models AWD models

607 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re CAUTION ■ When raising your vehicle Make sure to observe the following precautions to reduce the possibility ofdeath or serious injury: ● When using a floor jack, follow the instructions of the manual provided withthe jack. ● Do not use t...

608 4-3. Do-it-yourself maintenance Engine compartment 1AR-FE engine Washer fluid tank ( → P. 625) Engine oil level dipstick ( → P. 610) Engine oil filler cap ( → P. 612) Engine coolant reservoir ( → P. 616) Brake fluid reservoir ( → P. 619) Fuse box ( → P. 648) Battery ( → P. 621) Electric cooling ...

611 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Wipe the dipstick and reinsert it fully. 1AR-FE engine LowFull 2GR-FE engine STEP 6

612 4-3. Do-it-yourself maintenance ■ Adding engine oil If the oil level is below or nearthe low level mark, add engineoil of the same type as thatalready in the engine. Make sure to check the oil type and prepare the items needed beforeadding oil. Remove the oil filler cap by turning it countercloc...

613 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Engine oil consumption ● The amount of engine oil consumed depends on the oil viscosity, thequality of the oil and the way the vehicle is driven. ● More oil is consumed under driving conditions such as high speeds andfrequent accelerati...

615 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re CAUTION ■ Used engine oil ● Used engine oil contains potentially harmful contaminants which maycause skin disorders such as inflammation and skin cancer, so careshould be taken to avoid prolonged and repeated contact. To remove usedengine...

616 4-3. Do-it-yourself maintenance Engine coolant The coolant level is satisfactory if it is between the “FULL” and “LOW”lines on the reservoir when the engine is cold. Reservoir cap“FULL”“LOW” If the level is on or below the“LOW” line, add coolant up to the“FULL” line. ■ Coolant selection Only use...

617 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re CAUTION ■ When the engine is hot Do not remove the engine coolant reservoir cap. The cooling system may be under pressure and may spray hot coolant if thecap is removed, causing burns or other injuries. NOTICE ■ When adding coolant Coolan...

618 4-3. Do-it-yourself maintenance Radiator and condenser Check the radiator and condenser and clear away any foreignobjects. If either of the above parts is extremely dirty or you are not sure oftheir condition, have your vehicle inspected by your Toyota dealer. CAUTION ■ When the engine is hot Do...

619 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Brake fluid ■ Checking fluid level The brake fluid level should bebetween the “MAX” and “MIN”lines on the tank. “MAX”“MIN” ■ Adding fluid Lift the cover off. Make sure to check the fluid type and prepare the necessary item. Fluid type FMV...

620 4-3. Do-it-yourself maintenance ■ Brake fluid can absorb moisture from the air Excess moisture in the brake fluid can cause a dangerous loss of brakingefficiency. Use only newly opened brake fluid. CAUTION ■ When filling the reservoir Take care as brake fluid can harm your hands and eyes and dam...

621 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Battery Check the battery as follows: ■ Battery exterior Make sure that the battery terminals are not corroded and thatthere are no loose connections, cracks, or loose clamps. TerminalsHold-down clamp ■ Before recharging When recharging, ...

622 4-3. Do-it-yourself maintenance ■ After recharging/reconnecting the battery (vehicles with a smart keysystem) ● Unlocking the doors using the smart key system may not be possibleimmediately after reconnecting the battery. If this happens, use the wire-less remote control or the mechanical key to...

623 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re CAUTION ■ Chemicals in the battery Batteries contain poisonous and corrosive sulfuric acid and may producehydrogen gas which is flammable and explosive. To reduce the risk of deathor serious injury, take the following precautions while wo...

624 4-3. Do-it-yourself maintenance CAUTION ■ How to recharge the battery Only perform a slow charge (5 A or less). The battery may explode ifcharged at a quicker rate. ■ Emergency measures regarding electrolyte ● If electrolyte gets in your eyesFlush your eyes with clean water for at least 15 minut...

625 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Washer fluid If any washer does not work orthe low washer fluid warning lightcomes on, the washer tank maybe empty. Add washer fluid. CAUTION ■ When refilling washer fluid Do not refill washer fluid when the engine is hot or running, as w...

626 4-3. Do-it-yourself maintenance Tires Replace or rotate tires in accordance with maintenance sched-ules and treadwear. ■ Checking tires New treadTreadwear indicatorWorn tread The location of treadwearindicators is shown by the“TWI” or “ ” marks, etc., molded on the sidewall ofeach tire. Vehicles...

627 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Tire rotation Vehicles with a spare tire of a different wheel type from theinstalled tires Rotate the tires in the ordershown. To equalize tire wear andextend tire life, Toyota recom-mends that tire rotation iscarried out at the same in...

628 4-3. Do-it-yourself maintenance Installing tire pressure warning valves and transmitters When replacing tires or wheels, tire pressure warning valves andtransmitters must also be installed. When new tire pressure warning valves and transmitters areinstalled, new ID codes must be registered in th...

630 4-3. Do-it-yourself maintenance Registering ID codes The tire pressure warning valve and transmitter is equipped with aunique ID code. When replacing a tire pressure warning valve andtransmitter, it is necessary to register the ID code. Have the ID coderegistered by your Toyota dealer. ■ When to...

631 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Maximum load of tire Check that the number given by dividing the maximum load by 1.10 ofthe replacement tire is greater than 1/2 of the Gross Axle Weight Ratings(GAWR) of either the front axle or the rear axle, whichever is greater. ■ T...

632 4-3. Do-it-yourself maintenance ■ Initializing the tire pressure warning system Initialize the system with the tire inflation pressure adjusted to the speci-fied level. ■ If the tread on snow tires wears down below 0.16 in. (4 mm) The effectiveness of the tires as snow tires is lost. ■ If you pr...

634 4-3. Do-it-yourself maintenance CAUTION ■ When inspecting or replacing tires Observe the following precautions to prevent accidents. Failure to do somay cause damage to parts of the drive train, as well as dangerous han-dling characteristics, which may lead to an accident resulting in death orse...

635 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re NOTICE ■ Repairing or replacing tires, wheels, tire pressure warning valvesand transmitters and tire valve caps ● When removing or fitting the wheels, tires or the tire pressure warningvalves and transmitters, contact your Toyota dealer a...

636 4-3. Do-it-yourself maintenance Tire inflation pressure ■ Tire inflation pressure The recommended cold tire inflation pressure and tire size aredisplayed on the tire and loading information label. ( → P. 743 )

637 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Inspection and adjustment procedure Tire valveTire pressure gauge Remove the tire valve cap.Press the tip of the tire pressure gauge onto the tire valve.Read the pressure using the gauge gradations.If the tire inflation pressure is not ...

638 4-3. Do-it-yourself maintenance ■ Tire inflation pressure check interval You should check tire inflation pressure every two weeks, or at leastonce a month.Do not forget to check the spare. ■ Effects of incorrect tire inflation pressure Driving with incorrect tire inflation pressure may result in...

639 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re CAUTION ■ Proper inflation is critical to save tire performance Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accidentcausing death or serious injury. ● Excessive wear ● Uneven wear ● Po...

640 4-3. Do-it-yourself maintenance Wheels If a wheel is bent, cracked or heavily corroded, it should bereplaced.Otherwise, the tire may separate from the wheel or cause a lossof handling control. ■ Wheel selection When replacing wheels, care should be taken to ensure thatthey are equivalent to thos...

641 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ When replacing wheels The wheels of your vehicle are equipped with tire pressure warningvalves and transmitters that allow the tire pressure warning system toprovide advanced warning in the event of a loss in tire inflation pressure.Whe...

642 4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be cleaned or changed regularly tomaintain air conditioning efficiency. ■ Removal method Turn the engine switch (vehicles without a smart key sys-tem) or “ENGINE START STOP” switch (vehicles with asmart key ...

643 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Remove the filter. The “ ↑ UP” marks shown on the filter should be pointing up. ■ Cleaning method If the filter is dirty, clean byblowing compressed airthrough the filter from theunderside. Hold the air gun 2 in. (5 cm)from the filter and...

644 4-3. Do-it-yourself maintenance ■ Checking interval Inspect, clean and replace the air conditioning filter according to the mainte-nance schedule. In dusty areas or areas with heavy traffic flow, more fre-quent cleaning or early replacement may be required. (For scheduledmaintenance information,...

645 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Wireless remote control/electronic key battery Replace the battery with a new one if it is discharged. ■ You will need the following items: ● Flathead screwdriver ● Lithium battery CR2032 ■ Replacing the battery (vehicles without a smart ...

646 4-3. Do-it-yourself maintenance ■ Replacing the battery (vehicles with a smart key system) Take out the mechanical key. Remove the cover. To prevent damage to the key,cover the tip of the screwdriverwith a rag. Remove the depleted battery. Insert a new battery with the“+” terminal facing up. STE...

647 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Use a CR2032 lithium battery ● Batteries can be purchased at your Toyota dealer, local electrical appli-ance shops or camera stores. ● Replace only with the same or equivalent type recommended by themanufacturer. ● Dispose of used batte...

648 4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may haveblown. If this happens, check and replace the fuses as necessary. Vehicles without a smart key system Turn the engine switch off. Vehicles with a smart key system Turn ...

649 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re After a system failure, see “Fuse layout and amperage rat-ings” ( → P. 651) for details about which fuse to check. Take out the pullout tool. Only type A fuses can beremoved using the pullout tool. Check if the fuse has blown. Type A Norm...

650 4-3. Do-it-yourself maintenance Type C Normal fuseBlown fuse Contact your Toyota dealer. Type D Normal fuseBlown fuse Contact your Toyota dealer. Type E Normal fuseBlown fuse Contact your Toyota dealer.

651 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Fuse layout and amperage ratings ■ Engine compartment Fuse Ampere Circuit 1 DSS1 7.5 A PCS (Pre-collision system), dynamic radar cruise control sys-tem 2 ST NO.2 7.5 A Starting system, multiport fuel injection system/sequential multi-port...

655 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Under the driver’s side instrument panel Fuse Ampere Circuit 1 P/OUTLET 15 A Power outlets 2 RAD NO.2 7.5 A Audio system, navigation system, rear seat entertainment system 3 ECU-ACC 10 A Main body ECU, clock, shift lock system, power re...

659 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ After a fuse is replaced ● If the lights do not turn on even after the fuse has been replaced, a bulbmay need replacement. ( → P. 660) ● If the replaced fuse blows again, have the vehicle inspected by yourToyota dealer. ■ If there is an...

660 4-3. Do-it-yourself maintenance Light bulbs You may replace the following bulbs yourself. The difficulty level ofreplacement varies depending on the bulb. If necessary bulbreplacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, ...

661 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re Replacing light bulbs ■ Headlight low beams (halogen bulb) For left side only: Open the fuse box cover. ( → P. 648) Unplug the connector whilepushing the lock release. ■ Rear bulb locations Back-up light Rear turn signal light License pla...

662 4-3. Do-it-yourself maintenance Turn the bulb base counterclock-wise. ■ Headlight high beams and daytime running lights For left side only: Open the fuse box cover. ( → P. 648) Turn the bulb base counterclock-wise. Unplug the connector whilepushing the lock release. STEP 3 STEP 1 STEP 2 ITO43P16...

664 4-3. Do-it-yourself maintenance ■ Front turn signal/parking and front side marker lights For left side only: Open the fuse box cover. ( → P. 648) Vehicles without discharge headlights Turn the bulb base counterclock-wise. Vehicles with discharge headlights Remove the light bulb. STEP 1 STEP 2 ST...

665 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ Rear turn signal light Remove the securing bolts andremove the unit. Turn the bulb base counterclock-wise. Remove the light bulb. STEP 1 STEP 2 STEP 3

666 4-3. Do-it-yourself maintenance ■ Tail and back-up lights Remove the back door trimboard. Turn the bulb base counterclock-wise. Tail lightBack-up light Remove the light bulb. Tail lightBack-up light STEP 1 STEP 2 STEP 3

667 4-3. Do-it-yourself maintenance 4 Mainten ance an d ca re ■ License plate lights Remove the back door trimboard. Turn the bulb base counterclock-wise. Remove the light bulb. STEP 1 STEP 2 STEP 3

668 4-3. Do-it-yourself maintenance ■ Lights other than the above If any of the lights listed below has burnt out, have it replaced byyour Toyota dealer. ● Headlight low beams (discharge bulbs) ● High mounted stoplight ● Stop/tail and rear side marker lights ● Outer foot lights (if equipped) ■ Disch...

670 4-3. Do-it-yourself maintenance CAUTION ■ Discharge headlights (if equipped) ● Contact your Toyota dealer before replacing discharge headlights (includ-ing light bulbs). ● Do not touch the discharge headlight’s high voltage socket when the head-lights are turned on.An extremely high voltage of 3...

672 5-1. Essential information Emergency flashers NOTICE ■ To prevent battery discharge Do not leave the emergency flashers on longer than necessary when theengine is not running. Use the emergency flashers if the vehicle malfunctions or isinvolved in an accident. Press the switch to flash allthe tu...

5 W hen tr ou ble ar ises 673 5-1. Essential information If your vehicle needs to be towed Before towing The following may indicate a problem with your transaxle. Contactyour Toyota dealer before towing. ● The engine is running but the vehicle will not move. ● The vehicle makes an abnormal sound. If...

674 5-1. Essential information Towing with a sling-type truck Do not tow with a sling type truckto prevent body damage. Towing with a wheel-lift type truck From the front (2WD models) Release the parking brake.

5 W hen tr ou ble ar ises 675 5-1. Essential information From the front (AWD models) Use a towing dolly under the rearwheels. From the rear Use a towing dolly under thefront wheels. Using a flat bed truck If you use chains or cables to tiedown your vehicle, the anglesshaded in black must be 45 ° . D...

676 5-1. Essential information NOTICE ■ To prevent body damage when towing with a sling-type truck Do not tow with a sling-type truck, either from the front or rear. ■ To prevent causing serious damage to the transaxle and Active TorqueControl 4WD system (AWD models) when towing using a wheel-lift t...

5 W hen tr ou ble ar ises 677 5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probablyneeds adjustment or repair. Contact your Toyota dealer as soon aspossible. ■ Visible symptoms ● Fluid leaks under the vehicle(Water dripping from...

678 5-1. Essential information Fuel pump shut off system Follow the procedure below to restart the engine after the system isactivated. Vehicles without a smart key system Turn the engine switch to the “ACC” or “LOCK” position.Restart the engine. Vehicles with a smart key system Turn the “ENGINE STA...

5 W hen tr ou ble ar ises 679 5-1. Essential information Event data recorder In a crash or near crash event The SRS airbag sensor assembly contains the EDR. In a crash ornear crash event, this device may record some or all of the followinginformation: ● Gasoline engine speed ● Whether the brake peda...

680 5-1. Essential information Disclosure of the data Toyota will not disclose the data recorded in an EDR to a third partyexcept when: ● An agreement from the vehicle’s owner (or the leasing company fora leased vehicle) is obtained ● Officially requested to by the police or other authorities ● Nece...

5 W hen tr ou ble ar ises 681 5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer sounds... Stop the vehicle immediately. Continuing to drive the vehiclemay be dangerous. The following warning indicates a possible problem in the brake sys-tem. Immediately stop the vehi...

682 5-2. Steps to take in an emergency Stop the vehicle immediately. The following warnings indicate the possibility of damage to the vehi-cle that may lead to an accident. Immediately stop the vehicle in asafe place and contact your Toyota dealer. Have the vehicle inspected immediately. Failure to ...

684 5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem,check that the warning light turns off. Warning light Warning light/Details Correction procedure Open door warning light (warning buzzer) * 1 Indicates that a do...

5 W hen tr ou ble ar ises 687 5-2. Steps to take in an emergency * 1 :Open door warning buzzer: A buzzer will sound if the vehicle reaches a speed of 3 mph (5 km/h) with anydoor open. * 2 :Driver’s and front passenger’s seat belt warning buzzers: The driver’s and front passenger’s seat belt warning ...

688 5-2. Steps to take in an emergency ■ If the malfunction indicator lamp comes on while driving First check the following: ● Is the fuel tank empty?If it is, fill the fuel tank immediately. ● Is the fuel tank cap loose?If it is, tighten it securely. The malfunction indicator lamp will go off after...

5 W hen tr ou ble ar ises 689 5-2. Steps to take in an emergency ■ If the tire pressure warning system is inoperative The tire pressure warning system will be disabled in the following condi-tions:(When the condition becomes normal, the system will work properly.) ● If tires not equipped with tire p...

5 W hen tr ou ble ar ises 691 5-2. Steps to take in an emergency CAUTION ■ When the electric power steering system warning light comes on The steering wheel may become extremely heavy. If the steering wheel becomes heavier than usual when operating, holdfirmly and operate using more force than usual...

692 5-2. Steps to take in an emergency CAUTION ■ Maintenance of the tires Each tire, including the spare (if provided), should be checked monthlywhen cold and inflated to the inflation pressure recommended by thevehicle manufacturer on the vehicle placard or tire inflation pressurelabel (tire and lo...

5 W hen tr ou ble ar ises 693 5-2. Steps to take in an emergency CAUTION Your vehicle has also been equipped with a TPMS (tire pressure warningsystem) malfunction indicator to indicate when the system is not operat-ing properly. The TPMS (tire pressure warning system) malfunction indi-cator is combi...

694 5-2. Steps to take in an emergency If a warning message is displayed ∗ ∗ : If equipped The multi-information display shows warnings of system malfunc-tions or incorrectly performed operations. When a message isshown, perform corrections as indicated in the message. Master warning light The maste...

5 W hen tr ou ble ar ises 695 5-2. Steps to take in an emergency If you have a flat tire (vehicles with run-flat tires) ■ In some condition (such as at high temperatures) You cannot continue driving for up to 100 miles (160 km). ■ For the detailed information on run-flat tires See the tire warranty ...

696 5-2. Steps to take in an emergency NOTICE ■ When replacing the tires When removing or fitting the wheels, tires or the tire pressure warningvalve and transmitter, contact your Toyota dealer as the tire pressurewarning valve and transmitter may be damaged if not handled correctly. ■ When driving ...

5 W hen tr ou ble ar ises 697 5-2. Steps to take in an emergency If you have a flat tire (vehicles with standard tires) Remove the flat tire and replace it with the spare tire provided. ■ Before jacking up the vehicle ● Stop the vehicle on a hard, flat surface. ● Set the parking brake. ● Shift the s...

698 5-2. Steps to take in an emergency Taking out the jack and tools Remove the cover. Remove the adapter socket. Remove the jack. STEP 1 STEP 2 STEP 3

5 W hen tr ou ble ar ises 699 5-2. Steps to take in an emergency Remove the wheel nut wrench. Taking out the spare tire Slide the front passenger’s seat to the front-most lock positionand the right side second seat to the rear-most lock positionso they will not interfere with the jack handle. Open t...

5 W hen tr ou ble ar ises 701 5-2. Steps to take in an emergency Replacing a flat tire Chock the tires. Slightly loosen the wheel nuts(one turn). STEP 1 Flat tire Wheel chock positions Front Left-hand side Behind the rear right-hand side tire Right-hand side Behind the rear left-hand side tire Rear ...

5 W hen tr ou ble ar ises 703 5-2. Steps to take in an emergency Installing the spare tire Remove any dirt or foreign mat-ter from the wheel contact sur-face. If foreign matter is on the wheelcontact surface, the wheel nutsmay loosen while the vehicle isin motion, causing the tire tocome off. Instal...

704 5-2. Steps to take in an emergency Firmly tighten each wheel nuttwo or three times in the ordershown in the illustration. Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m) Stow the flat tire, tire jack and all tools. Stowing the flat tire Remove clasps and strap. Place tire standing up in rear ...

5 W hen tr ou ble ar ises 705 5-2. Steps to take in an emergency Clip clasp to outboard hook. Clip other clasp to center oropposite hook location. Pull strap to tighten and securetire. STEP 3 STEP 4 STEP 5 ■ The compact spare tire ● The compact spare tire is identified by the label “TEMPORARY USEONL...

706 5-2. Steps to take in an emergency ■ Jack point guide ■ After completing the tire change The tire pressure warning system must be reset. ( → P. 628) ■ When using the compact spare tire As the compact spare tire is not equipped with a tire pressure warningvalve and transmitter, low inflation pres...

5 W hen tr ou ble ar ises 707 5-2. Steps to take in an emergency CAUTION ■ When using the compact spare tire ● Remember that the compact spare tire provided is specificallydesigned for use with your vehicle. Do not use your compact spare tireon another vehicle. ● Do not use more than one compact spa...

708 5-2. Steps to take in an emergency CAUTION ■ Speed limit when using the compact spare tire Do not drive at speeds in excess of 50 mph (80 km/h) when a compactspare tire is installed on the vehicle.The compact spare tire is not designed for driving at high speeds. Failureto observe this precautio...

5 W hen tr ou ble ar ises 709 5-2. Steps to take in an emergency CAUTION ■ Replacing a flat tire Observe the following precautions to reduce the risk of death or seriousinjury: ● Do not touch the disc wheels or the area around the brakes immedi-ately after the vehicle has been driven. After the vehi...

710 5-2. Steps to take in an emergency NOTICE ■ When loosening or tightening the spare tire clamp bolt Do not use an impact wrench. Use the adapter socket and jack handle. ■ Do not drive the vehicle with a flat tire Do not continue driving with a flat tire.Driving even a short distance with a flat t...

5 W hen tr ou ble ar ises 711 5-2. Steps to take in an emergency NOTICE ■ To avoid damaging to the tire pressure warning valves and trans-mitters Do not use liquid sealants on flat tires. ■ After taking out or stowing the spare tire Make sure to secure the tire carrier by tightening the clamp bolt t...

712 5-2. Steps to take in an emergency If the engine will not start If the engine will not start even though correct starting proceduresare being followed ( → P. 212, 215), consider each of the following points: ■ The engine will not start even though the starter motoroperates normally. One of the f...

5 W hen tr ou ble ar ises 713 5-2. Steps to take in an emergency Emergency start function (vehicles with a smart key system) When the engine does not start, the following steps can be used asan interim measure to start the engine if the “ENGINE START STOP”switch is functioning normally: Set the park...

714 5-2. Steps to take in an emergency If the shift lever cannot be shifted from P If the shift lever cannot be shifted with your foot on the brake pedal,there may be a problem with the shift lock system (a system to pre-vent accidental operation of the shift lever). Have the vehicleinspected by you...

716 5-2. Steps to take in an emergency If you lose your keys/wireless remote control transmitter New genuine keys can be made by your Toyota dealer. For vehicleswith the smart key system, bring the other key and the key numberstamped on the key number plate. For vehicles without the smart keysystem,...

5 W hen tr ou ble ar ises 717 5-2. Steps to take in an emergency If the electronic key does not operate properly ∗ Locking and unlocking the doors and key linked functions Using the mechanical key( → P. 31) in order to perform the following operations. Locks all doors Unlocks all doors Turning the k...

718 5-2. Steps to take in an emergency Changing “ENGINE START STOP” switch modes and starting theengine Shift the shift lever to P and apply the brakes. Touch the Toyota emblem side ofthe electronic key to the“ENGINE START STOP” switch. An alarm will sound to indicatethat the start function cannotde...

5 W hen tr ou ble ar ises 719 5-2. Steps to take in an emergency ■ Stopping the engine Shift the shift lever to P and press the “ENGINE START STOP” switch asyou normally do when stopping the engine. ■ Replacing the key battery As this above procedure is a temporary measure, it is recommended that th...

720 5-2. Steps to take in an emergency If the battery is discharged The following procedures may be used to start the engine if the vehi-cle’s battery is discharged.You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi-cle with a ...

5 W hen tr ou ble ar ises 723 5-2. Steps to take in an emergency ■ Starting the engine when the battery is discharged The engine cannot be started by push-starting. ■ To prevent battery discharge ● Turn off the headlights and the audio system while the engine is off. ● Turn off any unnecessary elect...

724 5-2. Steps to take in an emergency CAUTION ■ Battery precautions The battery contains poisonous and corrosive acidic electrolyte, whilerelated parts contain lead and lead compounds. Observe the following pre-cautions when handling the battery: ● When working with the battery, always wear safety ...

5 W hen tr ou ble ar ises 725 5-2. Steps to take in an emergency If your vehicle overheats If your engine overheats: Stop the vehicle in a safe place and turn off the air condi-tioning system.Check to see if steam is coming out from under the hood.If you see steam: Stop the engine. Carefully lift th...

726 5-2. Steps to take in an emergency ■ Overheating If you observe the following, your vehicle may be overheating: ● The engine coolant temperature gauge enters the red zone or a loss ofpower is experienced. ● Steam comes out from under the hood. Add engine coolant if neces-sary. Water can be used ...

5 W hen tr ou ble ar ises 727 5-2. Steps to take in an emergency CAUTION ■ To prevent an accident or injury when inspecting under the hood ofyour vehicle ● If steam is seen coming from under the hood, do not open the hood untilthe steam has subsided. The engine compartment may be very hot, caus-ing ...

728 5-2. Steps to take in an emergency If the vehicle becomes stuck CAUTION ■ When attempting to free a stuck vehicle If you choose to push the vehicle back and forth to free it, make sure the sur-rounding area is clear to avoid striking other vehicles, objects or people. Thevehicle may also lunge f...

5 W hen tr ou ble ar ises 729 5-2. Steps to take in an emergency NOTICE ■ To avoid damaging the transaxle and other components ● Avoid spinning the wheels and pressing the accelerator pedal more thannecessary. ● If the vehicle remains stuck even after these procedures are performed,the vehicle may r...

730 5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop thevehicle in the normal way, stop the vehicle using the following pro-cedure: Steadily step on the brake pedal with both feet and firmlydepress it....

5 W hen tr ou ble ar ises 731 5-2. Steps to take in an emergency CAUTION ■ If the engine has to be turned off while driving ● Power assist for the brakes and steering wheel will be lost, making thebrake pedal harder to depress and the steering wheel heavier to turn.Decelerate as much as possible bef...

734 6-1. Specifications Maintenance data (fuel, oil level, etc.) Dimensions and weights Overall length 200.2 in. (5085 mm) Overall width 78.1 in. (1985 mm) Overall height * 1 2WD models ASL30L-PFTEKA,ASL30L-PRTEKA * 2 69.5 in (1765 mm) GSL30L-PRTSKA * 2 68.7 in (1745 mm) Others 68.9 in (1750 mm) AWD...

735 6-1. Specifications 6 Vehicl e sp ecification s * 1 : Unladen vehicle * 2 : The model code is indicated on the Certification Label. For details, see “Vehicle identification” below. Vehicle identification ■ Vehicle identification number The vehicle identification number (VIN) is the legal identif...

736 6-1. Specifications ■ Engine number The engine number is stamped on the engine block as shown. 1AR-FE engine 2GR-FE engine

737 6-1. Specifications 6 Vehicl e sp ecification s Engine Fuel Lubrication system Model 1AR-FE, 2GR-FE Type 1AR-FE engine 2GR-FE engine 4-cylinder in line, 4-cycle, gasoline 6-cylinder V type, 4-cycle, gasoline Bore and stroke 1AR-FE engine 2GR-FE engine 3.54 × 4.13 in. (90.0 × 105.0 mm) 3.70 × 3.2...

738 6-1. Specifications ■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. UseToyota approved “Toyota Genuine Motor Oil” or equivalent to satisfythe following grade and viscosity. Oil grade: ILSAC multigrade engine oil Recommended viscosity: SAE 0W-20 SAE 0W-20 is the ...

739 6-1. Specifications 6 Vehicl e sp ecification s Cooling system Ignition system Capacity 1AR-FE engine2GR-FE engine 9.2 qt. (8.7 L, 7.7 Imp.qt.) Without towing package 11.0 qt. (10.4 L, 9.2 Imp.qt.) With towing package 11.7 qt. (11.1 L, 9.8 Imp.qt.) Coolant type Use either of the following. • “To...

740 6-1. Specifications Electrical system Automatic transaxle * : The fluid capacity is a reference quantity. If replacement is necessary, contact your Toyota dealer. Battery Open voltage * at 68 ° F (20 ° C): 12.6 ⎯ 12.8 V Fully charged 12.2 ⎯ 12.4 V Half charged 11.8 ⎯ 12.0 V Discharged ( * : Volt...

743 6-1. Specifications 6 Vehicl e sp ecification s Tires and wheels 17-inch tires 18-inch tires Tire size P235/60R17 100T, T155/80R17 101M (spare) Tire inflation pressure(Recommended cold tire inflation pressure) Front: 35 psi (240 kPa, 2.4 kgf/cm 2 or bar) Rear: 35 psi (240 kPa, 2.4 kgf/cm 2 or ba...

746 6-1. Specifications Fuel information ■ Fuel tank opening for unleaded gasoline To help prevent incorrect fueling, your Toyota has a fuel tank opening thatonly accommodates the special nozzle on unleaded fuel pumps. ■ Gasoline quality In very few cases, driveability problems may be caused by the ...

747 6-1. Specifications 6 Vehicl e sp ecification s ■ Recommendation of the use of gasoline containing detergent additives ● Toyota recommends the use of gasoline that contains detergent additivesto avoid build-up of engine deposits. ● All gasoline sold in the U.S.A. contains detergent additives to ...

748 6-1. Specifications NOTICE ■ Notice on fuel quality ● Do not use improper fuels. If improper fuels are used, the engine will bedamaged. ● Do not use leaded gasoline.Leaded gasoline can cause damage to your vehicle’s catalytic converterscausing the emission control system to malfunction. ● Do not...

749 6-1. Specifications 6 Vehicl e sp ecification s Tire information Typical tire symbols Run-flat tire or standard tire Compact spare tire Tire size ( → P. 752) DOT and Tire Identification Number (TIN) ( → P. 751) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that fol...

750 6-1. Specifications Run-flat tire (RFT) or standard tire ( → P. 695) This vehicle can be equipped with either run-flat tires (RFT) or standardtires. An “RFT” or “DSST” mark is molded on the sidewall of the run-flattire. Tire ply composition and materials Plies are layers of rubber-coated paralle...

751 6-1. Specifications 6 Vehicl e sp ecification s Typical DOT and Tire Identification Number (TIN) DOT symbol * Tire Identification Number(TIN)Tire manufacturer’s identifica-tion markTire size codeManufacturer’s optional tiretype code (3 or 4 letters)Manufacturing weekManufacturing year * : The DO...

752 6-1. Specifications Tire size ■ Typical tire size information The illustration indicates typical tire size. Tire use(P = Passenger car, T = Temporary use)Section width (millimeters)Aspect ratio(tire height to section width)Tire construction code(R = Radial, D = Diagonal)Wheel diameter (inches)Lo...

753 6-1. Specifications 6 Vehicl e sp ecification s Tire section names BeadSidewallShoulderTreadBeltInner linerReinforcing rubberCarcassRim linesBead wiresChafer Uniform Tire Quality Grading This information has been prepared in accordance with regulationsissued by the National Highway Traffic Safet...

754 6-1. Specifications ■ Treadwear The treadwear grade is a comparative rating based on the wearrate of the tire when tested under controlled conditions on a speci-fied government test course. For example, a tire graded 150 would wear one and a half (1-1/2)times as well on the government course as ...

755 6-1. Specifications 6 Vehicl e sp ecification s Warning: The temperature grades of a tire assume that it is properlyinflated and not overloaded.Excessive speed, underinflation, or excessive loading, either sepa-rately or in combination, can cause heat buildup and possible tire fail-ure. Glossary...

761 6 Vehicl e sp ecification s 6-2. Customization Customizable features Item Function Default setting Customized setting Smart key system and wireless remote con-trol( → P. 34 , 52) Unlocking operation * Drivers door unlocked in one step, all doors unlocked in two steps All doors unlocked in one st...

765 6-2. Customization 6 Vehicl e sp ecification s Customizing the features by using the multi-information display Press the “SETUP” button whilethe vehicle is stopped. The “Custom Settings” screen isdisplayed on the multi-informationdisplay. If left idle for approximately 20seconds, the display wil...

766 6-2. Customization Choose a desired setting bypressing the “INFO” or “SETUP”button, then press the “SELECTRESET” button to select. If any settings are changed, thedisplay will revert to the previousscreen. The illustration assumes that“Auto Locking” was chosen in . The current setting is indicat...

768 6-3. Initialization Items to initialize Item When to initialize Reference Power sliding door(if equipped) After reconnecting or changing the battery P. 65 Power back door(if equipped) After reconnecting or changing the battery P. 77 Engine oil mainte-nance data (U.S.A. only) After changing engin...

771 7 For owners Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructionsextracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions inEnglish.

62 SIENNA AAS_U (OM45460U) Alphabetical index Alphabetical index Armrests ..................................... 11AUTO ACCESS SEAT .................. 6 Battery Disconnecting............................ 7 Beep sounds .............................. 22Before operating the seat.......... 20 Child safety...

792 GAS STATION INFORMATION Auxiliary catch lever P. 604 Fuel filler door P. 147 Hood release lever P. 604 Fuel filler door opener P. 147 Tire inflation pressure P. 743 Back door opener P. 77 Fuel tank capacity (Reference) 20.9 gal. (79 L, 17.4 Imp.gal.) Fuel type Unleaded gasoline with an Octane Ra...

TABLE OF CONTENTS Index 2 1-1. Key information Keys ..................................... 30 1-2. Opening, closing and locking the doors Smart key system................. 34Wireless remote control ....... 52Front doors ........................... 59Sliding doors ........................ 65Back door ...

1 2 3 4 5 6 7 3 2-1. Driving procedures Driving the vehicle............... 200Engine (ignition) switch (vehicles without smart key system)............. 212 Engine (ignition) switch (vehicles with smart key system)............. 215 Automatic transaxle ............ 221Turn signal lever ..................

TABLE OF CONTENTS Index 4 3-1. Using the air conditioning system and defogger Front manual air conditioning system.......... 344 Front automatic air conditioning system.......... 352 Rear manual air conditioning system.......... 362 Rear automatic air conditioning system.......... 365 Rear window an...

1 2 3 4 5 6 7 5 3-5. Using the hands-free phone system (for cellular phone) Hands-free phone system (for cellular phone) features ............................. 488 Using the hands-free phone system (for cellular phone) ............ 493 Making a phone call ............ 502Setting a cellular phone ......

TABLE OF CONTENTS Index 6 4-3. Do-it-yourself maintenance Do-it-yourself service precautions ...................... 600 Hood................................... 604Positioning a floor jack ....... 606Engine compartment .......... 608Tires ................................... 626Tire inflation pressure...

1 2 3 4 5 6 7 7 6-1. Specifications Maintenance data (fuel, oil level, etc.) ............ 734 Fuel information .................. 746Tire information ................... 749 6-2. Customization Customizable features ........ 761 6-3. Initialization Items to initialize ................. 768 Reporting ...