Page 2 - CONTENTS
CONTENTS Introduction.............................................................................. 1 Setup ........................................................................................ 3 Using the CD-R/CD-RW Drive ................................................. 6 Troubleshooting..........
Page 3 - General Features; Formats Compatibility
1 INTRODUCTION – SR-M8102 General Features CD-R/CD-RW disc write/rewrite at 52X/32X 3-way Disc Eject (eject button, software, emergency eject hole) Average Random Access Time CD 110ms CD-RW 120ms Horizontal or Vertical Mount 2MByte Buffer Playback interchangeability for CD-ROM discs BUS Interface - ...
Page 5 - Jumper Settings; Figure 1.Mode Select Jumper
3 SETUP – SR-M8102 The following steps must be performed to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pins located on the rear of the CD-R/CD-RW...
Page 6 - Connecting Cables; IDE BUS Cable
4 Placing CD-R/CD-RW Drive inside your Computer Now that you have set the jumpers, you are ready to install your CD-R/CD-RW drive inside your computer. Important Note: Disconnect power from your computer system before beginning installation. Remove computer cover and faceplate if required. Refer to ...
Page 7 - Completing Installation
5 Power Cable - Connect an internal computer power supply cable to the power socket at the back of the CD-R/CD-RW drive. One side of the plug has chamfered edges, so the power connector fits only one way. Push plug completely into the socket making sure the plug fits correctly. Figure 4.Installing P...
Page 8 - Figure 1.Inserting Disc; Inserting a Disc - Vertically
6 USING THE CD-R/CD-RW Drive – SR-M8102 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is mounted horizontally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's Loading tray by pressing the Eject Button. 2. Place disc or into drive's Loadin...
Page 9 - Figure 2.Inserting Disc Vertically; Removing a Disc
7 Figure 2.Inserting Disc Vertically Removing a Disc To remove a disc from the CD-R/CD-RW drive, perform the following steps: 1. Open the Loading Tray by pressing the Eject Button. 2. Slide disc holders away from disc. 3. Grasp disc by edges, and lift out of loading tray. 4. Press Eject Button again...
Page 10 - Figure 3.Using Emergency Eject; Cleaning Media
8 Figure 3.Using Emergency Eject Cleaning Media Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc accessing speed. If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather from the inner side outward.
Page 11 - TROUBLESHOOTING – SR-M8102; Problem; Solution
9 TROUBLESHOOTING – SR-M8102 Problem Solution Disc tray cannot be opened • Check that there is power to drive. • Use Emergency Eject instructions to open tray. Drive is not recognized by system • Is the drive connected properly? Are all cables plugged in properly (e.g. Power Cable, Interface Cable a...
Page 12 - General; Performance
10 SPECIFICATIONS –SR-M8102 General Interface ATAPI Format for Writing: Disc at once, Track at once, Session at once, Variable & Fixed Packet write Format Compatibility: CD-DA (Red Book) - Standard Audio CD & CD-TEXT CD-ROM (Yellow Book Mode 1&2) - Standard Data CD-ROM XA (Mode 2 Form 1&...
Page 14 - Connectors; Regulatory
12 Connectors DC input 4-pin Power Supply Connector ATAPI Interface Connector 40 Pin I/F ATAPI Standard Audio Connectors 4-pin and 2-pin connector (use matching housing, Part No. 70066, made by Molex Corp, or equivalent) Regulatory The SR-M8102 CD-R/RW has been certified by the following regulatory ...
Page 15 - DRIVE CONNECTORS –SR-M8102; Supplies Analog and Digital sound to your system.
13 DRIVE CONNECTORS –SR-M8102 Figure 1.SR-M8102 CD-R/CD-RW Drive Rear Panel - Connectors Power Connector Power is supplied to your CD-R/RW drive by the connection with your computer's +5V/+12V power cable to the power socket at the back of drive. One side of the plug has chamfered edges, so the powe...