Toshiba Satellite A70 - Manuals

5 5.375 x 8.375 ver 2.3 Telephone Company Procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures. If these changes might affect your servi...

6 5.375 x 8.375 ver 2.3 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or ...

7 5.375 x 8.375 ver 2.3 NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to t...

8 5.375 x 8.375 ver 2.3 Wireless LAN and your Health Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example...

9 5.375 x 8.375 ver 2.3 Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. L’utilisation de ce dispositif est autorisée seulement...

11 5.375 x 8.375 ver 2.3 USA – Federal Communications Commission (FCC) This device complies with Part 15 of FCC Rules. Operation of the devices in a Wireless LAN System is subject to the following two conditions: ❖ This device may not cause harmful interference. ❖ This device must accept any interfe...

12 5.375 x 8.375 ver 2.3 Caution: Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harm...

13 5.375 x 8.375 ver 2.3 2. Indication The indication shown below appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. OF: This equipment uses OFDM modulation. 3 The interference range of this equipment is less than 40m. 4 This equ...

14 5.375 x 8.375 ver 2.3 Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wireless module into other device. ❖ 5.17 GHz to 5.23 GHz for indoor use ...

19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Bluetooth wireles...

20 5.375 x 8.375 ver 2.3 Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth™ products with all PCs and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth™ cards from TOSH...

21 5.375 x 8.375 ver 2.3 community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the buil...

22 5.375 x 8.375 ver 2.3 Caution: FCC Interference Statement This device complies with part15 of the FCC rules. Operation is subject to the following two conditions: ❖ This device may not cause harmful interference, and ❖ This device must accept any interference received, including interference that...

23 5.375 x 8.375 ver 2.3 The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations. Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial,...

25 5.375 x 8.375 ver 2.3 Location of the required label (Sample shown below. Location of the label and manufacturing information may vary.) This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the user’s guide carefully and keep it f...

27 5.375 x 8.375 ver 2.3 Computer disposal information This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.o...

28 5.375 x 8.375 ver 2.3 Contents Introduction ............................................................... 35 This guide ...............................................................36Safety icons ............................................................37 Other icons used ....................

29 Contents 5.375 x 8.375 ver 2.3 Using the computer for the first time ......................53 Opening the display panel .................................53Your computer’s features and specifications ....54Turning on the power........................................55 Using the TouchPad™ ............

30 Contents 5.375 x 8.375 ver 2.3 Starting a program from Windows ® Explorer....80 Starting a program from the Run dialog box ....81 Saving your work ....................................................82Printing your work ..................................................84Backing up your files ......

32 Contents 5.375 x 8.375 ver 2.3 Internet features..............................................131Uploading and downloading files from the Internet ..............................................132 Exploring video features .......................................132Changing the display properties s...

34 Contents 5.375 x 8.375 ver 2.3 Appendix B: Power Cable Connectors...................... 180 Appendix C: Using ConfigFree™ with your Toshiba Computer ........................... 181 Getting Started ......................................................182 Starting ConfigFree .........................

35 5.375 x 8.375 ver 2.3 Introduction Welcome to the world of powerful and portable multimedia computers! With your new Toshiba notebook computer, your access to information can accompany you wherever you go. Your system comes with either the Microsoft ® Windows ® XP Home or Windows XP Professional ...

36 Introduction This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specificatio...

37 Introduction Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according t...

38 Introduction Other documentation 5.375 x 8.375 ver 2.3 Other icons used Additional icons highlight other helpful or educational information: TECHNICAL NOTE: This icon highlights technical information about the computer. HINT: This icon denotes helpful hints and tips. DEFINITION: This icon indicat...

39 Introduction Service options 5.375 x 8.375 ver 2.3 Service options Toshiba offers a full line of optional service programs to complement its limited warranty. To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularl...

40 5.375 x 8.375 ver 2.3 Chapter 1 Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety ...

41 Getting Started Selecting a place to work 5.375 x 8.375 ver 2.3 ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in temperature or humidity and sources of temperature chang...

42 Getting Started Selecting a place to work 5.375 x 8.375 ver 2.3 Placement of the computer Proper placement of the computer and external devices is important to avoid stress-related injuries. ❖ Place the computer on a flat surface at a comfortable height and distance. You should be able to type wi...

43 Getting Started Selecting a place to work 5.375 x 8.375 ver 2.3 Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort. ❖ Position your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfor...

44 Getting Started Selecting a place to work 5.375 x 8.375 ver 2.3 Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes. Arms and wrists ❖ Avoid bending, arching, or t...

45 Getting Started Selecting a place to work 5.375 x 8.375 ver 2.3 computer frequently and focus your eyes on a distant object for at least 30 seconds. Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to...

47 Getting Started Setting up your computer 5.375 x 8.375 ver 2.3 Important information on your computer’s cooling fan Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. The cooling fan may be located on the bottom of the computer. To prevent possib...

48 Getting Started Setting up your computer 5.375 x 8.375 ver 2.3 Setting up your software The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software. 1 From the welcome screen, click Next to enter the Setup Wizard. 2 Confirm acceptance of Microsoft’s...

49 Getting Started Setting up your computer 5.375 x 8.375 ver 2.3 A window displays the message, “Who will use this computer?” 7 Enter your name and click Next to complete the process. A window displays the message, “Thank you.” 8 Click Finish to continue. Your computer restarts automatically. Regis...

50 Getting Started Connecting to a power source 5.375 x 8.375 ver 2.3 Connecting to a power source Your computer requires power to operate. Use the power cable and AC adapter to connect the computer to a live electrical outlet, or to charge the computer’s battery. Sample power cable and AC adapter H...

52 Getting Started Charging the main battery 5.375 x 8.375 ver 2.3 ❖ Glows green when the battery is fully charged. ❖ Is unlit when the computer is not connected to an external power source. For information on determining battery power, see “Monitoring battery power” on page 110 . Damaged power cabl...

53 Getting Started Using the computer for the first time 5.375 x 8.375 ver 2.3 TECHNICAL NOTE: When your computer is using all of the power provided by the AC adapter to run applications, features, and devices, the recharging of the battery cannot occur. Your computer’s Power Saver utility can be us...

54 Getting Started Using the computer for the first time 5.375 x 8.375 ver 2.3 To avoid damaging the display panel, do not force it beyond the point where it moves easily. Never lift or move the computer using the display panel. Small bright dots may appear on your TFT display when you turn on your ...

55 Getting Started Using the TouchPad™ 5.375 x 8.375 ver 2.3 This information applies to all the features and icons described in this guide. Turning on the power 1 Check that any drives on the computer are empty. 2 Turn on the computer by pressing and releasing the power button located on the top of...

56 Getting Started Using the TouchPad™ 5.375 x 8.375 ver 2.3 ❖ To move the cursor to the right side of the page, slide your finger across the TouchPad from left to right. ❖ To move it to the left side, slide your finger from right to left. Because the TouchPad is much smaller than the display screen...

61 Getting Started Installing additional memory (optional) 5.375 x 8.375 ver 2.3 9 Replace the expansion memory module slot cover. 10 Replace the screw and tighten it. 11 Turn the computer over and reconnect any cables you removed. 12 Turn on the computer. To verify that the computer correctly recog...

62 Getting Started Using an external keyboard 5.375 x 8.375 ver 2.3 4 Complete the procedure by following steps 10 through 12 in “Installing additional memory (optional)” on page 57 . Using an external keyboard If you prefer to use a full-size keyboard, you can attach one to your computer. The compu...

64 Getting Started Setting up a printer 5.375 x 8.375 ver 2.3 Setting up a printer If you started your computer with a printer connected and turned on, it may have been detected automatically (Plug and Play). If this is not the case, then you must install the printer driver for the model of printer ...

67 Getting Started Using external display devices 5.375 x 8.375 ver 2.3 Using external display devices Your computer comes with a built-in LCD display, but you can also connect an external display device to the available video port: ❖ An external monitor or projector via the RGB (monitor) port. Befo...

68 Getting Started Using external display devices 5.375 x 8.375 ver 2.3 ❖ Built-in display only ❖ Built-in display and external monitor simultaneously ❖ External monitor only 3 Release the Fn key. TECHNICAL NOTE: You can also change these settings using the Display Properties Box. Set the option for...

69 Getting Started Turning off the computer 5.375 x 8.375 ver 2.3 Turning off the computer It is a good idea to turn off your computer when you are not using it for a while. If you are using the computer for the first time, leave the computer plugged into a power source (even though the computer is ...

70 Getting Started Caring for your computer 5.375 x 8.375 ver 2.3 Closing the display panel When you are finished, shut the computer down and close the display panel to keep dust and dirt out of the computer. If you close the computer while it is still on, these actions will occur: ❖ If you have the...

71 Getting Started Caring for your computer 5.375 x 8.375 ver 2.3 Moving the computer Before moving your computer, even across the room, make sure all disk activity has ended (the disk activity lights stop glowing) and all external peripheral cables are disconnected. Never pick up the computer by it...

73 5.375 x 8.375 ver 2.3 Chapter 2 Learning the Basics This chapter lists some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work temporarily stays in the computer’s memory until you save it to the disk. You will lose all uns...

75 Learning the Basics Using the keyboard 5.375 x 8.375 ver 2.3 Using the keyboard Keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The spacebar creates a space character instead of just passing over an area of the page. ❖ The lowercase ...

76 Learning the Basics Using the keyboard 5.375 x 8.375 ver 2.3 Ctrl, Fn, and Alt keys Ctrl, Fn and Alt keys The Ctrl , Fn , and Alt keys do different things depending on the program you are using. For more information, see your program documentation. Function keys The function keys (not to be confu...

77 Learning the Basics Using the keyboard 5.375 x 8.375 ver 2.3 Overlay keys Keyboard overlay keys The keys with numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the ten-key keypad on a des...

78 Learning the Basics Using the keyboard 5.375 x 8.375 ver 2.3 To use the cursor control overlay when the numeric overlay is on, press and hold down Shift while you use the cursor control keys. To return to the numeric overlay, release Shift . To turn off the numeric keypad overlay, hold down the F...

79 Learning the Basics Starting a program 5.375 x 8.375 ver 2.3 Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows Explorer. If you prefer to open the program fi...

81 Learning the Basics Starting a program 5.375 x 8.375 ver 2.3 Starting a program from the Run dialog box This example uses the Run command to start WordPad: 1 Click Start , then click Run . The Run dialog box appears. Sample Run dialog box 2 In the Run dialog box: ❖ If you know the program’s locat...

82 Learning the Basics Saving your work 5.375 x 8.375 ver 2.3 Saving your work Before you turn off the computer, save your work to the hard disk drive. Always save your data even when you are using the Stand by. If your battery fully discharges, your information will be lost. Your computer can be co...

83 Learning the Basics Saving your work 5.375 x 8.375 ver 2.3 3 Type a file name, then click Save . HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name. The Windows ® XP operating system supports file names o...

84 Learning the Basics Printing your work 5.375 x 8.375 ver 2.3 To save: ❖ A file you are updating, open the program’s File menu and click Save . ❖ A new file, choose Save As from the File menu, type a name for the file, and click OK . HINT: To make another copy of the file you are currently working...

85 Learning the Basics Backing up your files 5.375 x 8.375 ver 2.3 Backing up your files Backing up your files means copying individual files to media, such as a CD. Or copying entire sections of your hard disk to another device such as a tape drive or to your network partition. To back up to a CD, ...

86 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to overwrite a file that already exists on the hard disk. Make sure the backup version is the one you want before overwriting the exi...

87 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 A special feature allows you to play audio CDs even when the computer is turned off. Drive components and control buttons The DVD-ROM or multi-function drive resides on the left side of the computer. The CD/DVD co...

88 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 HINT: When the computer is off and the DVD-ROM or rmulti-function drive is on, press the stop/eject control button on the left side of the keyboard to eject a disc. CD/DVD control and Music CD buttons The control ...

89 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 The stop/eject button stops a disc that is currently playing. You can eject a disc by pressing the stop/eject button twice. Use this method to eject a disc when the computer is turned off and after the Music CD bu...

91 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 Playing an audio CD Insert an Insert an audio CD and close the disc tray. The computer automatically detects a disc in the drive and opens the Audio CD window. To play an audio CD select the Play Audio CD using Wi...

93 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 Before using headphones to listen to an audio CD, turn the volume dial down. Playing the CD with the volume set too high could damage your ears. Playing CDs using Auto-Run If you insert a CD into the DVD-ROM/multi...

94 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 and CD-Rewritable (CD-RW) discs; and read DVD-R/-RW or DVD RAM discs. Copy protection technology included in certain media may prevent or limit recording or viewing of the media. For details on how to use the soft...

95 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 3 Remove the disc from the disc tray and place it in its protective cover. If the disc is spinning when you open the disc tray, wait for the disc to stop before removing it. 4 Close the disc tray by pressing gentl...

96 Learning the Basics Powering down the computer 5.375 x 8.375 ver 2.3 ❖ To clean a disc, wipe it from the center outwards (not in a circle) with a clean, dry cloth. If necessary, moisten the cloth with water or a neutral cleaner (not benzine or rubbing alcohol). Let the disc dry completely before ...

97 Learning the Basics Powering down the computer 5.375 x 8.375 ver 2.3 Using Turn Off or Shut down For the Windows ® XP Home operating system, follow these steps to shut down the computer: 1 Click Start , select Turn off computer . The Turn off computer dialog box appears. Sample Turn off computer ...

98 Learning the Basics Powering down the computer 5.375 x 8.375 ver 2.3 Hibernation command The Hibernation command shuts the computer down completely, but it first saves the current state of the computer to the hard disk. Since Hibernation mode does not require power to maintain the saved informati...

99 Learning the Basics Powering down the computer 5.375 x 8.375 ver 2.3 Stand By command The Stand by puts the computer into a power-saving mode. Stand by holds the current state of the computer in memory so that, when you restart the computer, you can continue working from where you left off. Facto...

100 Learning the Basics Powering down the computer 5.375 x 8.375 ver 2.3 1 Click Start , Control Panel , then Performance and Maintenance . 2 Click the Toshiba Power Management icon. The Power Options Properties dialog box appears. 3 Click the Advanced tab, and select the options you want. ❖ When I ...

101 Learning the Basics Using Hibernation 5.375 x 8.375 ver 2.3 Using Hibernation Follow these steps to power down the computer using Hibernation: 1 Click Start , select Turn off computer . The Turn off computer dialog box appears. 2 Hold down the Shift key. The Stand by option changes to the Hibern...

102 Learning the Basics Using Hibernation 5.375 x 8.375 ver 2.3 into Hibernation mode when you press the power button. ❖ When I close the lid Set this option to Hibernation for the computer to go into Hibernation mode when you close the display panel. Sample Toshiba Power Management Advanced tab 4 C...

103 Learning the Basics Using Stand by 5.375 x 8.375 ver 2.3 Using Stand by Follow these steps to power down the computer using the Stand by: 1 Click Start , select Turn off computer . The Turn off computer box appears. 2 Click Stand By . Sample Turn off computer dialog box The computer saves the st...

104 Learning the Basics Toshiba’s online resources 5.375 x 8.375 ver 2.3 1 Open the Start menu, then click Control Panel . 2 Click the Performance and Maintenance icon, and then click the Toshiba Power Management icon. 3 Click the Advanced tab. 4 Select Stand By for the options you want. When I pres...

105 5.375 x 8.375 ver 2.3 Chapter 3 Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power standby mode when it is not being used, thereby conserving energy and saving money in the process. It has a numb...

106 Mobile Computing Running the computer on battery power 5.375 x 8.375 ver 2.3 Battery Notice Battery life may vary depending on applications, power management settings and features utilized. Recharge time varies depending on usage. The battery may not charge while the computer is consuming full p...

107 Mobile Computing Charging the batteries 5.375 x 8.375 ver 2.3 Changes to these settings may result in system performance or stability issues. Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup cha...

109 Mobile Computing Charging the batteries 5.375 x 8.375 ver 2.3 Leave the power connected, and the battery should begin charging after a few minutes. HINT: Once the battery is fully charged, we recommend that you operate your computer on battery power until the battery discharges completely. Doing...

110 Mobile Computing Monitoring battery power 5.375 x 8.375 ver 2.3 It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working. When Hibernation mode...

111 Mobile Computing Monitoring battery power 5.375 x 8.375 ver 2.3 The current power source and battery power remaining section displays the current charge state of the battery. The value displays as a percentage of remaining battery charge. 3 Click the Battery Power Meter tab. Sample Toshiba Power...

112 Mobile Computing Monitoring battery power 5.375 x 8.375 ver 2.3 ❖ How much you use the hard disk and other drives ❖ Whether you use any optional devices to which the battery supplies power, such as a PC Card ❖ Where you are working—since operating time decreases at low temperatures There are var...

113 Mobile Computing Monitoring battery power 5.375 x 8.375 ver 2.3 your open programs and files to the hard disk before shutting down. Setting battery alarms Your computer can be configured to warn you when the battery is running low. You can set multiple alarms. Each alarm can be set to alert you ...

114 Mobile Computing Changing the main battery 5.375 x 8.375 ver 2.3 Changing the main battery When your battery power is running low, you have two options—connect the computer to an AC power source or install a charged battery. When handling a battery, be careful not to drop it or short-circuit its...

116 Mobile Computing Taking care of your battery 5.375 x 8.375 ver 2.3 Sample inserting battery When you replace your battery, slide the battery lock towards you to lock the battery pack. Taking care of your battery The following sections offer tips on how to take care of your battery and prolong it...

117 Mobile Computing Taking care of your battery 5.375 x 8.375 ver 2.3 cause it to overheat and may cause damage to the battery or the computer. ❖ Do not incinerate a spent battery, as this could cause it to explode and release toxic materials. ❖ If a battery is leaking or damaged, replace it immedi...

118 Mobile Computing Disposing of used batteries safely 5.375 x 8.375 ver 2.3 4 Connect the AC adapter to the computer and the power cord to a power outlet. The DC-IN or AC power-light LED should glow green, and the Battery LED should glow amber to indicate that the battery pack is being charged. If...

119 Mobile Computing Traveling tips 5.375 x 8.375 ver 2.3 The computer’s main battery is a Lithium-Ion (Li-Ion) battery, which can explode if not properly replaced, used, handled, or disposed of. Putting spent batteries in the trash is not only irresponsible, it may be illegal. Dispose of the batter...

120 5.375 x 8.375 ver 2.3 Chapter 4 Exploring Your Options In this chapter, you will explore some of the special features of your Satellite ® Series notebook computer. Exploring the desktop The desktop is the launching pad for everything you can do in the Windows ® XP Home or XP Professional operati...

121 Exploring Your Options Exploring the desktop 5.375 x 8.375 ver 2.3 Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, taskbar, system tray, and background pattern. Sample Windows ® XP operating system desktop Icons An icon represe...

123 Exploring Your Options Setting up for communications 5.375 x 8.375 ver 2.3 Taskbar Each time you open a program, a button associated with that program appears on the taskbar. With some programs, a button appears on the taskbar for each document or window you open. You can use these buttons to qu...

124 Exploring Your Options Setting up for communications 5.375 x 8.375 ver 2.3 ❖ Communicate with your office’s local area network (LAN), or a larger corporate wide area network (WAN). For specific information about connecting to a LAN or WAN, consult your network administrator. ❖ Send a fax directl...

125 Exploring Your Options Setting up for communications 5.375 x 8.375 ver 2.3 1 Click Start , Control Panel , then Printers and Other Hardware . 2 Click Phone and Modem options . 3 The Phone and Modem options window appears. 4 Click the Modems tab. A location box appears. 5 In the Attached To field...

127 Exploring Your Options Setting up for communications 5.375 x 8.375 ver 2.3 Connecting your computer to a network You can connect your computer to a network to increase its capabilities and functionality using one of its communication ports. Accessing a network To access a network: ❖ At the offic...

128 Exploring Your Options Setting up for communications 5.375 x 8.375 ver 2.3 Using Wireless LAN Connectivity The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design...

129 Exploring Your Options An overview of using the Internet 5.375 x 8.375 ver 2.3 An overview of using the Internet The following sections give a quick introduction to the Internet and some of its exciting features, under these headings: ❖ The Internet ❖ The World Wide Web ❖ Internet Service Provid...

130 Exploring Your Options An overview of using the Internet 5.375 x 8.375 ver 2.3 Internet Service Providers To connect a computer directly to the Internet, many people and businesses use an Internet Service Provider (ISP). An ISP is a company that has the equipment and the telecommunication lines ...

131 Exploring Your Options An overview of using the Internet 5.375 x 8.375 ver 2.3 Surfing the Internet Once connected to the Internet, the Web browser displays a home page, for example, your ISP’s home page on the Internet or your company’s Web site home page. To visit a desired Web site, type the ...

132 Exploring Your Options Exploring video features 5.375 x 8.375 ver 2.3 ❖ Online shopping Many Web sites offer products and services for sale. Uploading and downloading files from the Internet Transferring files from one computer to another is termed uploading (transferring data from your computer...

133 Exploring Your Options Changing the display properties setting 5.375 x 8.375 ver 2.3 Changing the display properties setting 1 Right-click anywhere on your desktop and select Properties . The Display Properties dialog box appears. Sample Display Properties dialog box 2 Click the Settings tab. 3 ...

134 Exploring Your Options Exploring audio features 5.375 x 8.375 ver 2.3 Exploring audio features You can use your computer to record sounds using an external microphone. You can play .wav sound files or audio CDs using the built-in speakers, headphones or external speakers. For information on play...

135 Exploring Your Options Exploring audio features 5.375 x 8.375 ver 2.3 Sample Sound Recorder screen 3 Click the Record button and speak normally into the microphone. You can only record 60 seconds at a time. 4 When you have finished recording, click the Stop button. 5 To hear what you just record...

136 Exploring Your Options Exploring audio features 5.375 x 8.375 ver 2.3 4 Click OK . Your new settings take effect the next time you record. Using external speakers or headphones Your computer is equipped with a full stereo sound system with internal speakers. Instead of using the internal speaker...

137 Exploring Your Options Using the i.LINK ® port 5.375 x 8.375 ver 2.3 Using the i.LINK ® port The i.LINK ® port on the left side of the computer provides an extremely fast data transfer rate (up to 400 mega bits per second [Mbps]). You can connect up to 63 external devices to the i.LINK ® port. I...

139 Exploring Your Options Using PC Cards 5.375 x 8.375 ver 2.3 Sample inserting a PC Card To avoid damaging the PC Card or the computer, do not force the card into the PC Card slot. Removing PC Cards 1 Stop the PC Card by clicking the Safely Remove Hardware icon on the System tray. After the Safe t...

140 Exploring Your Options Using PC Cards 5.375 x 8.375 ver 2.3 Hot swapping One of the great things about PC Cards is that you can replace one PC Card with another while the computer is on. This is called “hot swapping.” Hot swapping precautions Although you can insert a PC Card at any time, to avo...

141 Exploring Your Options Using the Media Card Reader 5.375 x 8.375 ver 2.3 Using the Media Card Reader For systems with a Media Card Reader, use of a number of media cards is supported: SD ™ Card, SmartMedia, MultiMediaCard™, Memory Stick, Memory Stick Pro, and XD Card. The cards can be used with ...

142 Exploring Your Options Using the Media Card Reader 5.375 x 8.375 ver 2.3 If the card has a connector (metal area), do not touch the connector. You could expose the storage area to static electricity, which can destroy data. Do not remove a card while data is being written or read. Even when the ...

143 5.375 x 8.375 ver 2.3 Chapter 5 If Something Goes Wrong Some problems you may encounter when using your notebook computer are relatively easy to identify and solve. Others may require help from your dealer or the manufacturer of a software program. This chapter aims to help you solve many proble...

145 If Something Goes Wrong 5.375 x 8.375 ver 2.3 Sample Windows Task Manager Shutdown menu, Turn Off option The computer shuts down. Your program performs an illegal operation. If you receive the message, “ Your program has performed an illegal operation ,” you should record the details of the mess...

146 If Something Goes Wrong Problems when you turn on the computer 5.375 x 8.375 ver 2.3 6 Save the file and refer to it when you contact the software manufacturer. Problems when you turn on the computer These problems may occur when you turn on the power. The computer will not start. Make sure you ...

147 If Something Goes Wrong The Windows ® operating system is not working 5.375 x 8.375 ver 2.3 The computer displays the Non-System disk or disk error message. Press any key. If this does not resolve then problem, press Ctrl, Alt , and Del to restart the computer. The Windows ® operating system is ...

148 If Something Goes Wrong The Windows ® operating system is not working 5.375 x 8.375 ver 2.3 The Windows ® Advanced Options menu displays these options: ❖ Safe Mode ❖ Safe Mode (with Networking) ❖ Safe Mode (with Command Prompt) ❖ Enable Boot Logging ❖ Enable VGA Mode ❖ Last known good configurat...

149 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 My browser cannot find a site I bookmarked. The World Wide Web is constantly changing. A site you bookmarked yesterday may not be available today or its server may be down for temporary repair. Try again later. The Windo...

150 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 4 Choose from specific topics and follow the steps. If there is still a problem, the operating system should display a message that explains what the conflict is. A plan of action The smooth operation of the system depen...

151 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Plug and Play With Plug and Play and the Windows ® XP operating system, avoiding hardware conflicts is easy. Plug and Play is a computer standard that helps the system BIOS (basic input/output system) and the operating s...

152 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Fixing a problem with Device Manager Device Manager provides a way to check and change the configuration of a device. Changing the default settings using Device Manager can cause other conflicts that make one or more dev...

153 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Checking device properties Device Manager provides a way to view the properties of a device. Properties include the name of the manufacturer, the type of device, the drivers installed, and the system resources assigned t...

154 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Memory module problems Incorrectly connected or faulty memory modules may cause errors that seem to be device-related. It is worthwhile checking for these first: 1 Turn off the computer via the Start menu. 2 Remove the m...

156 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 For more information on maximizing battery power, see “Charging the batteries” on page 107 . Keyboard problems If, when you type, strange things happen or nothing happens, the problem may be related to the keyboard itsel...

157 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 If you are using the built-in screen, make sure the display priority is not set for an external monitor. To do this, press Fn and F5 simultaneously (once). If this does not correct the problem, press Fn and F5 simultaneo...

159 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Over a period of time, and depending on the usage of the computer, the brightness of the LCD Screen will deteriorate. This is an intrinsic characteristic of LCD technology. Screen will dim when the computer is operated o...

160 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 The Check Disk box appears (for example, Check Disk C). 6 You can choose one or both options: ❖ Automatically fix file system errors ❖ Scan for and attempt recovery of bad sectors ❖ Click Start . Error-checking runs the ...

161 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Examine the disc to see whether it is dirty. If necessary, wipe it with a clean cloth dipped in water or a neutral cleaner. Replace the disc in the tray. Make sure it is lying flat, label side uppermost. Press the disc d...

162 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Sound system problems You do not hear any sound from the computer. Adjust the volume control. If you are using external headphones or speakers, check that they are securely connected to your computer. The computer emits ...

163 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Other cards must be set up before you can use them. Use the Windows ® XP PC Card (PCMCIA) Wizard to set up the card. Refer to your Microsoft ® documentation for more information, or refer to the documentation that came w...

165 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 3 Remove the card from the slot. Never swap modules when the computer is in Hibernation or Standby mode. This is known as “warm swapping” and is not supported with this computer For more information on Hibernation and St...

166 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Printer problems This section lists some of the most common printer problems: The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the print...

167 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Modem problems This section lists common modem problems: The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port and the ...

168 If Something Goes Wrong Develop good computing habits 5.375 x 8.375 ver 2.3 Develop good computing habits Make sure you are prepared. Save your work frequently. You can never predict when your computer will lock, forcing you to close a program and lose unsaved changes. Many software programs bui...

169 If Something Goes Wrong If you need further assistance 5.375 x 8.375 ver 2.3 Your local computer store or book store sells a variety of self-help books you can use to supplement the information in the manuals. If you need further assistance If you have followed the recommendations in this chapte...

170 If Something Goes Wrong If you need further assistance 5.375 x 8.375 ver 2.3 Contacting Toshiba If you still need help and suspect that the problem is hardware-related, Toshiba offers a variety of resources to help you. You can access Toshiba on the Internet using any Internet browser by typing ...

171 If Something Goes Wrong Other Toshiba Internet Web sites 5.375 x 8.375 ver 2.3 Other Toshiba Internet Web sites Toshiba’s worldwide offices toshiba.com Worldwide Toshiba corporate site computers.toshiba.com Marketing and product information in the USA www.toshiba.ca Canada www.toshiba-Europe.com...

173 5.375 x 8.375 ver 2.3 Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls. Instant password security Fn + This hot key blanks the di...

174 Hot Keys Instant password security 5.375 x 8.375 ver 2.3 the display’s content reappear. The Windows ® operating system log-on screen will appear, prompting you for a password. After typing in the password for the current user, press Enter. To activate the password feature: 1 Click Start , Contr...

175 Hot Keys Sound 5.375 x 8.375 ver 2.3 Follow the steps listed in the Windows help to set up your password-protected screen saver. To ensure the password protection is activated after pressing Fn + F1 (to activate instant security), wait ten seconds before walking away from the computer. Sound Fn ...

176 Hot Keys Stand by mode 5.375 x 8.375 ver 2.3 Stand by mode Fn + This hot key puts the computer into Stand by mode. ❖ A message box is displayed by default to confirm that the computer is going into Stand by mode. This message box can be set so it doesn’t display. Sample Stand by confirmation box...

177 Hot Keys Hibernation mode 5.375 x 8.375 ver 2.3 Hibernation mode Fn + This hot key puts the computer into Hibernation mode. ❖ If Hibernation mode is enabled (the default) a message box is displayed by default to confirm the computer is going into Hibernation mode. The message box can be set so i...

178 Hot Keys Display modes 5.375 x 8.375 ver 2.3 Display modes Fn + This hot key cycles through the power-on display options. The display modes are: ❖ Built-in display panel only ❖ Built-in display panel and external monitor simultaneously ❖ External monitor only ❖ Built-in display panel and externa...

179 Hot Keys Enabling a wireless device 5.375 x 8.375 ver 2.3 Enabling a wireless device Disabling or enabling the TouchPad Keyboard hot keys Fn + This hot key turns the cursor control overlay on and off. Fn + This hot key turns the numeric overlay on and off. Fn + This hot key turns the scroll lock...

180 5.375 x 8.375 ver 2.3 Appendix B Power Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada UL approvedCSA approved United Kingdom BS...

181 5.375 x 8.375 ver 2.3 Appendix C Using ConfigFree™ with your Toshiba Computer ConfigFree™ is a set of utilities that makes it easy to control communication devices and network connections. ConfigFree also lets you identify communication problems and create profiles for easy switching between loc...

182 Getting Started 5.375 x 8.375 ver 2.3 Getting Started This section contains information about the ConfigFree main screen, and how to start and setup ConfigFree. For more detailed information on setting up and using ConfigFree, see the Help File included in the application. Starting ConfigFree To...

183 ConfigFree Utilities 5.375 x 8.375 ver 2.3 Sample ConfigFree Launcher ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network-connection problems. Using Connectivity Doctor, you can view detailed network information by simply mov...

188 ConfigFree Utilities 5.375 x 8.375 ver 2.3 2 Click your own computer at the center of the map. 3 Configured devices are automatically connected. Devices not yet configured launch the Add New Connection Wizard, where you can configure and connect to the device. Profile Settings The Profile Settin...

190 ConfigFree Utilities 5.375 x 8.375 ver 2.3 Sample Add Profile screen The online help provides real-world examples of setting up profiles for different networking environments. After you set up one or more profiles, you can check their settings and fine-tune them as necessary. Profiles can also b...

193 Using the Automatic Switch 5.375 x 8.375 ver 2.3 Using the Automatic Switch The Automatic Switch feature allows the computer to automatically switch profiles the next time it is powered on. This feature is particularly useful if you want your computer to automatically switch from the network con...

194 Semi-Automatic Switch Feature 5.375 x 8.375 ver 2.3 Semi-Automatic Switch Feature The Semi-Automatic feature alerts you when the computer connects to a Service Set Identifier (SSID) stored in a profile, When the computer connects to the designated SSID, a notification window appears. You can the...

195 5.375 x 8.375 ver 2.3 Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. AC alternating current BIOS basic input/output system bps bits per second CD compact disc CD-ROM compact d...

197 Glossary 5.375 x 8.375 ver 2.3 PCMCIA Personal Computer Memory Card International Association RAM random access memory RFI radio frequency interference ROM read-only memory RTC real-time clock SCSI small computer system interface SDRAM synchronous dynamic random access memory SRAM static random ...

210 5.375 x 8.375 ver 2.3 Index A AC power light 51 accessories memory 57 audio features 134 Auto-Run 93 avoiding injury 41 B backing up files 74 battery caring for 116 changing 114 charge not lasting 155 charging 69 , 107 , 108 conserving power 111 disposal 118 installing 114 light 51 , 110 monitor...