Toshiba RELIABILITY IN MOTION 1000- Manuals

IV 5.4 EPO Port (emergency power off) ................................................................... 16 5.5 Network Transient Protector .......................................................................... 16 5.6 Load Segments ..................................................................

V Manual’s Purpose and Scope The purpose of this manual is to provide information on how to safely install, operate, and maintain your TIC power electronics product. This manual includes a section of general safety instructions that describes the warning labels and symbols that are used throughout t...

VI TOSHIBA is a registered trademark of Toshiba Corporation. All other product or trade references appearing in this manual are registered trademarks of their respective owners. Toshiba International Corporation (TIC) shall not be liable for direct, indirect, special, or consequential damages result...

VII Contacting Toshiba International Corporation’s Customer Support Center Toshiba International Corporation’s Customer Support Center can be contacted to obtain help in resolving any Uninterruptible Power System problems that you may experience or to provide application information. The center is o...

VIII EMC Statements FCC Part 15 NOTICE : Pursuant to section 15 of the FCC rules this product has been tested and complies with the conditions of a Class B digital device. The product has been established as offering sufficient protection against dangerous interference for installations in a residen...

IX Declaration of Conformity Request Units labeled with a CE mark comply with the following standards and directives: Harmonic Standards: EN 50091-1-1 and EN 50091-2. EU Directives: 73/23/EEC, Council Directive on equipment designed for use within certain voltage limits. 93/68/EEC, Amending Directiv...

X General Safety Instructions DO NOT attempt to install, operate, maintain or dispose of this equipment until you have read and understood all of the product safety information and directions that are contained in this instruction manual. Safety Alert Symbol / Signal Words The Safety Alert Symbol in...

XI 2. Warning — The word WARNING in capital letters preceded by the safety alert symbol indicates that a potentially hazardous situation exists that, if not avoided, could result in death or serious injury to personnel. 3. Caution/Attention — The word CAUTION or ATTENTION in capital letters preceded...

XII Special Symbols Other warning symbols may appear in conjunction with the Danger, Warning , and Caution symbol and are used to specify special hazards. These warnings describe particular areas where special care and/or procedures are required in order to prevent serious injury and possible death....

XIII Important Safety Instructions This manual contains important instructions that should be followed during the installation, maintenance, and operation of the UPS and its batteries to assure safe and proper operation. 1. Turn off, lockout, and tagout all power sources before connecting the power ...

XIV For further information on workplace safety visit www.osha.gov Misuse of this equipment could result in injury and equipment damage. In no event will Toshiba Corporation be responsible or liable for either indirect or consequential damage or injury that may result from the misuse of this equipme...

XV —Strict adherence to the following precautions is a requirement when working with batteries— To be performed by Qualified Personnel only . 1. Verify that the UPS is off and that the power cord is disconnected from the power source. 2. Remove watches, rings or other metal objects. 3. Use tools wit...

XVI Instructions Importantes Concernant LA SÉCURITÉ CONSERVER CES INSTRUCTIONS Cette notice contient des instructions importantes concernant la sécurité. Une battery peut présenter un risque de choc électrique, de brûlure par transfert d' énergie. L' élimination des batteries est règlementèe. Consul...

XVII Inspection/Storage/Disposal Inspection Upon receipt of the UPS, an inspection for shipping damage should be performed. Use caution when removing the unit from the pallet. Refer to labels or documentation attached to packing material. Uncrating Check the unit for loose, broken, bent or otherwise...

XIX Installation Precautions 1. Install the unit in a well-ventilated location; allow at least 10 cm (4 inches) on all sides for air ventilation and for maintenance. 2. Install the unit in a stable, level and upright position that is free of excessive vibration. 3. Install the unit where the ambient...

XX 12. Connect the output terminals of the UPS to the load (refer to NEC Article 300 – Wiring Methods and Article 310 – Conductors For General Wiring). Size the branch circuit conductors in accordance with NEC Table 310.16. Conductor Routing and Grounding 1. Use separate metal conduits for routing t...

XXI Operating Precautions 1. The UPS should not be powered up until the entire operation manual has been read. 2. The voltage of the input power source must be within the range of +10% to -30% of the rated input voltage. The input frequency must be within the rated input frequency range. Voltages an...

1 1. Introduction The information provided in this manual covers single phase 1000 – 3000 VA uninterruptible power systems (UPS). Included in this manual is information on the installation, operation, safety precautions, shipping, and storage of the equipment. Installation must be carried out in acc...

2 2.1 General Description As a double conversion on-line UPS, it is able to supply uninterrupted, clean single-phase power to your critical systems while keeping batteries charged continuously, even if the utility power fails. Other features of the UPS includes • Auto-Restart and Cold Start features...

3 Figure 1. Block diagram • An input filter reduces transients on the main supply. • For maintaining full battery charge, AC-power is rectified and regulated in the rectifier feeding power to the inverter and battery converter. • DC power is converted to AC in the inverter and passes it on to the lo...

4 Alternating between bypass and on-line modes is achieved automatically and in accordance with the conditions of the utility power. On-line mode may be used during times of utility power irregularities. The bypass mode should be used when power flows smoothly in order to obtain the greatest efficie...

8 4.2 Rear Panel Views 1000VA – 1500VA Tower Rear Panel 2000VA – 3000VA Tower Rear Panel (230V IEC) USB EXTERNAL BATTERY EXTERNAL BATTERY USB (120V NEMA) (230V IEC) (120V NEMA)

11 Figure 2 Example of Installation of Plug & Play products.

12 4.4 Front Panel Settings Listed below are the default settings of the primary UPS parameters. Settings Options Default Remarks 1) O/P VOLT SET (output voltage set) 100V/110V/115V/120V/127V 208/220/230/240 Vac 120V 230V 120V (FOR LV series) 230V (FOR HV series) 2) I/P FREQ SET (input frequency set...

14 5. Computer and Alarm Connections At the rear of the UPS is an interface that allows direct communication with a computer system (see figure 2). There is a RS232 serial data interface, a USB data interface, and an emergency power off switch. The RS232 port and the USB interface cannot be used sim...

15 5.2 Dry Contact Interface (optional card) Pin # Description I/O Type 1 UPS fail, relay contact, normally open, active close. output 2 Summary alarm, relay contact, normally open, active close. One of the following signals activate this signal: 1) Output fault 2) Bus fault 3) Over temperature 4) O...

17 6. User’s Guide to Operations Normal ongoing UPS operation requires little or no user input. Startup and shutdown requirements of the user are discussed in this section. 6.1 UPS Startup and Shutdown Starting the UPS • Ensure that installation is correct and that the input power cable is connected...

18 2. “ ” is the Enter button. (a) Press and hold the Enter button for at least 2 seconds to read the parameter settings of the UPS. Press the Enter button again to read the next parameter. (b) Ten seconds of inactivity will return the display to the original status. 3. “ ” is the Function button. (...

20 BACKUP TIME= xx min Shows Estimated Backup Time in Minutes BAT CHARG= xx% Shows Approximate Percentage of Battery Capacity TEMPERATURE= xxC Shows Approximate Ambient Temperature BAT PACK NUM= x Shows External Battery Pack Number RATING = xxxxVA Shows UPS Rating CPU VERSION xx.x Shows CPU Version ...

21 6.7 UPS Manual Test Manual UPS and Battery tests may be performed from the UPS configuration screen. Tests may be performed when the battery is not being charged. To run the battery test scroll to the “Manual Bat Test” parameter press the Enter button twice. ** Note : In order for the UPS to oper...

22 6.11 Troubleshooting Displayed on LCD Audible Alarm Alarm Description What You Should Do Output Overload Two Beeps/sec The UPS is overloaded (in Line Mode). More power required than the UPS can provide. The UPS operates in bypass. Remove loads from the UPS; least to most critical. If this solves ...

24 8. Technical Specifications 8.1 Power Range 1000-3000 VA (120V) Tower US 120V Model UT1A1A010C6 UT1A1A015C6 UT1A1A020C6 UT1A1A030C6 Rack- mount (2U) US 120V Model UT1A1A010C6RKB2 UT1A1A015C6RKB2 UT1A1A020C6RKB2 UT1A1A030C6RKB2 Input Voltage 120 VAC (80 – 144 V) Voltage Range +20% to -33% Capacity...

26 9. Warranty Information TOSHIBA INTERNATIONAL CORPORATION LIMITED WARRANTY POLICY (48 contiguous U.S. States, Canada & Mexico) (UNINTERRUPTIBLE POWER SYSTEM) TOSHIBA INTERNATIONAL CORPORATION (“TIC”) warrants that any Uninterruptible Power System (“UPS”) and Uninterruptible Power System Batte...

27 LIMITATIONS AND EXCLUSIONS 1. This limited warranty shall not cover the UPS, UPS parts, or BATTERY during their respective warranty periods, if the following storage, maintenance, installation, operating conditions are not met throughout the warranty periods (5 conditions below): Valve Regulated ...