Page 2 - CONTENTS; OUTDOOR; INSTALLATION MANUAL; INDOOR; OWNERS MANUAL
CONTENTS OUTDOOR INSTALLATION MANUAL RAV-SM561AT-E, RAV-SM801AT-E .................................................................... 4 RAV-SM1101AT-E, RAV-SM1401AT-E .............................................................. 16 INDOOR OWNERS MANUAL 4-Way Air Discharge Cassette Type RAV-SP1100...
Page 4 - PRECAUTIONS FOR SAFETY; To Disconnect the Appliance from Main Power Supply; ) must be used for the power supply line of this conditioner.; WARNING; • Connect the connecting cable correctly.; Do not store it in a wet basement or expose to rain or water.; New Refrigerant Air Conditioner Installation; CAUTION
– 4 – RAV-SM561AT-E, RAV-SM801AT-E 1 PRECAUTIONS FOR SAFETY • Ensure that all Local, National and International regulations are satisfied.• Read this “PRECAUTIONS FOR SAFETY” carefully before Installation.• The precautions described below include the impor tant items regarding safety. Obser ve them ...
Page 5 - Inappropriate grounding may cause electric shock.; Required tools for installation work; ACCESSORY AND REFRIGERANT; Accessory and Installation Parts; • Piping kit used for the conventional refrigerant cannot be
– 5 – RAV-SM561AT-E, RAV-SM801AT-E • When the air conditioner is installed in a small room, provide appropriate measures to ensure that the concentration of refrigerant leakage occur in the room does not exceed the criticallevel. • Install the air conditioner securely in a location where the base ca...
Page 6 - Caution at addition of refrigerant; Caution at addition of refrigerant; Before installation; Be careful to the following items before installation.; Length of refrigerant pipe; Air purge; • Do not use refrigerant charged in the outdoor unit; Electrical cabling; • Be sure to fix the power cables and indoor/outdoor
– 6 – RAV-SM561AT-E, RAV-SM801AT-E Length of refrigerant pipe connected to indoor/outdoor unit 20 m or shorter ∗ 21 m to 30 m ∗ Caution at addition of refrigerant When the total length of refrigerant pipe exceeds20 m, add 20 g/m of refrigerant and the maximumtotal length of pipe is 30 m.(Max. amount...
Page 7 - Necessary Space for Installation; Obstacle at rear side; Obstacle at front side; Installation Place
– 7 – RAV-SM561AT-E, RAV-SM801AT-E 500 Strong wind Strong wind 2) Supposing the wind direction during the operation season of the air conditioner,install the unit so that the discharge port isset at right angle to the wind direction. 4. Installation in the following places may result in some trouble...
Page 8 - Obstacles at both front and rear sides; Single unit installation; Serial installation at front and rear sides; Drain nipple; Installation of Outdoor Unit; • Before installation, check strength and horizontality; For Reference
– 8 – RAV-SM561AT-E, RAV-SM801AT-E 1000 or more 300 or more 1500 or more 2000 or more 200 or more 300 or more 300 or more 1000 or more 200 or more 1000 or more 1000 or more 1000 or more 150 or more <Obstacle also at the upper side> Obstacles at both front and rear sides Open the upper side and...
Page 9 - TAKE NOTICE THESE IMPORTANT 4 POINTS BELOW FOR PIPING WORK; Keep dust and moisture away from inside the connecting pipes.; REFRIGERANT PIPING; OK; Flaring; * In case of flaring for R410A with the conventional; • Projection margin in flaring :
– 9 – RAV-SM561AT-E, RAV-SM801AT-E Optional Installation Parts (Local Procure) Refrigerant Piping Connection <Piping connection> A B C Parts name Refrigerant pipingLiquid side : Ø6.4 mm or Ø9.5 mmGas side : Ø12.7 mm or Ø15.9 mm Pipe insulating material (polyethylenefoam, 6 mm thick) Putty, PVC...
Page 10 - Tightening of Connecting Part; SM80 type valve at gas side; REQUIREMENT; NO GOOD
– 10 – RAV-SM561AT-E, RAV-SM801AT-E Tightening of Connecting Part (Unit: N•m) Externallythreaded side Internallythreaded side Fix with spanner. Tighten with torque wrench. Half union or packed valve Flare nut Flare at indoor unit side Flare at outdoor unit side • Align the centers of the connecting ...
Page 11 - EVACUATING; Air Purge; Vacuum pump
– 11 – RAV-SM561AT-E, RAV-SM801AT-E 5 EVACUATING Air Purge This air conditioner can be installed up to the connecting pipe length and height difference in the following table. With respect to the preservation of terrestrial environment, adopt “Vacuum pump” for air purge (Evacuate air inthe connectin...
Page 12 - valve core, is firmly connected to the charge por t.; Valve handling precautions; • Open the valve stem or the handle until it
– 12 – RAV-SM561AT-E, RAV-SM801AT-E Compound pressure gauge Service port (Valve core (Setting pin)) Packed valve (Gas side) Pressure gauge Manifold valve Handle Hi(Keep fully closed) Charge hose(For R410A only) Vacuum pump adapter for counter-flow prevention(For R410A only) Handle Lo Charge hose(For...
Page 13 - ELECTRICAL WORK; How to wire; Tripping length power cord and connecting cable; How to remove the valve cover
– 13 – RAV-SM561AT-E, RAV-SM801AT-E Valve cover Piping cover Indoor/outdoor connecting cables Power cable 6 ELECTRICAL WORK For the air conditioner that has no power cable,connect a power cable as mentioned below. How to wire 1. Connect the connecting cable to the terminal as identified with their r...
Page 14 - FINAL INSTALLATION CHECKS; Check and Test Operation; * The conventional leak detector for HCFC refrigerant; Installation/Servicing Tools; Changes in the product and components
– 14 – RAV-SM561AT-E, RAV-SM801AT-E Valve cover Check points of outdoor unit Piping cover Flare nut connections (Indoor unit) 7 FINAL INSTALLATION CHECKS Check and Test Operation For R410A, use the leak detector exclusively manufactured forHFC refrigerant (R410A, R134a, etc.). * The conventional lea...
Page 15 - APPLICABLE CONTROL OF OUTDOOR UNIT; Demand control; Recovery method of refrigerant; • When recovering refrigerant in case of reinstallation; Work procedure; Using the remote controller, set FAN operation to; DANGER
– 15 – RAV-SM561AT-E, RAV-SM801AT-E 8 APPLICABLE CONTROL OF OUTDOOR UNIT You can response to the following items by attaching the parts sold separately “Applicationcontrol kit” (TCB-PCOS1E). Demand control • It saves the capacity of the outdoor unit by outside Demand signal to correspond to the temp...
Page 16 - • Read this “PRECAUTIONS FOR SAFETY” carefully before Installation.
– 16 – RAV-SM1101AT-E, RAV-SM1401AT-E 1 PRECAUTIONS FOR SAFETY • Ensure that all Local, National and International regulations are satisfied. • Read this “PRECAUTIONS FOR SAFETY” carefully before Installation. • The precautions described below include the impor tant items regarding safety. Obser ve ...
Page 17 - ) Philips screw driver
– 17 – RAV-SM1101AT-E, RAV-SM1401AT-E • After unpacking the unit, examine it carefully if there are possible damage. • Do not install in a place that might increase the vibration of the unit. • To avoid personal injury (with sharp edges), be careful when handling parts. • Perform installation work p...
Page 18 - Item
– 18 – RAV-SM1101AT-E, RAV-SM1401AT-E Before installation Be careful to the following items before installation. Length of refrigerant pipe 2 ACCESSORY AND REFRIGERANT Suction Suction hood (Side)Discharge hood Fin Suction hood (Rear side) Suction Fin Discharge Accessory and Installation Parts Refrig...
Page 21 - Refrigerant Piping Connection; Knockout procedure
– 21 – RAV-SM1101AT-E, RAV-SM1401AT-E Refrigerant Piping Connection CAUTION TAKE NOTICE THESE IMPORTANT4 POINTS BELOW FOR PIPING WORK 1. Keep dust and moisture away from inside the connecting pipes. 2. Tightly connect the connection between pipes and the unit. 3. Evacuate the air in the connecting p...
Page 22 - How to remove the front panel; • The metal pipes are attachable to the piping holes.; Pipe Forming/End Positioning
– 22 – RAV-SM1101AT-E, RAV-SM1401AT-E How to remove the front panel 1. Remove screws of the front panel. 2. Pull the front panel downward. Removing the front panel, the electric par ts appear atthe front side. • The metal pipes are attachable to the piping holes. If the size of the used power pipe d...
Page 23 - Valve at gas side
– 23 – RAV-SM1101AT-E, RAV-SM1401AT-E Tightening of Connecting Part (Unit: N•m) Externallythreaded side Internallythreaded side Fix with spanner. Tighten with torque wrench. Half union or packed valve Flare nut Flare at indoor unit side Flare at outdoor unit side • Align the centers of the connectin...
Page 25 - How to open the valve; Handle position; • Open the valve stem or the handle until it strikes
– 25 – RAV-SM1101AT-E, RAV-SM1401AT-E Service port (Valve core (Setting pin)) Compound pressure gauge Packed valve at gas side Pressure gauge Manifold valve Handle Hi(Keep fully closed) Charge hose(For R410A only) Vacuum pump adapter for counter-flow prevention(For R410A only) Handle Lo Charge hose(...
Page 27 - • Pressure of R410A is approx. 1.6 times higher than that of R22.; Useful Functions; Self-Diagnosis by LED Indication; LED indication and code checking
– 27 – RAV-SM1101AT-E, RAV-SM1401AT-E 7 FINAL INSTALLATION CHECKS Check and Test Operation For R410A, use the leak detector exclusively manufactured for HFC refrigerant (R410A, R134a, etc.). * The conventional leak detector for HCFC refrigerant (R22, etc.) cannot be used because its sensitivity for ...
Page 28 - tion to the indoor unit.
– 28 – RAV-SM1101AT-E, RAV-SM1401AT-E Installation/Servicing Tools • Incidentally, the “refrigerant cylinder” comes with the refrigerant designation (R410A) and protector coating in the U,S.’s ARI specified rose color (ARI color code: PMS 507). • Also, the “charge por t and packing for refrigerant c...
Page 30 - -Way Air Discharge Cassette Type
INDOOR OWNERS MANUAL CONTENTS 4-Way Air Discharge Cassette Type RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E Concealed Duct Type RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E Under Ceiling Type RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-...
Page 31 - WARNINGS ABOUT INSTALLATION; • Be sure to provide grounding.; TO DISCONNECT THE APPLIANCE FROM THE MAINS SUPPLY; The installation fuse (25A D type; WARNINGS ABOUR OPERATION; a long time as it is bad for the health.; WARNINGS ABOUT MOVEMENT AND REPAIR; • Do not move or repair any unit by yourself.; Remote controller
– 31 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E ACCESSORIES (SOLD SEPARATELY) PRECAUTIONS FOR SAFETY WARNING WARNINGS ABOUT INSTALLATION • Make sure to ask the qualified installation professional in electric work to install the air conditioner.If the air conditione...
Page 32 - CAUTIONS ABOUT INSTALLATION
– 32 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E CAUTION CAUTIONS ABOUT INSTALLATION • Be sure to confirm the following cautions. • Certainly lay the drain hose for perfect draining. Bad drainage may cause flooding in the house and getting furniturewet. • Make sure ...
Page 33 - PARTS NAME; Indoor unit; Pipes and electric wires; Suction air port; Button
– 33 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E PARTS NAME Indoor unit REMOTE CONTROLLER Air inlet (Side and rear) Pipes and electric wires Air outlet Suction air port The air in the room is sucked in from this port. Air filter Removes dust or trash.(Provided on th...
Page 34 - PARTS NAME OF REMOTE CONTROLLER; Display section
– 34 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E PARTS NAME OF REMOTE CONTROLLER Display section In the display example, all indicators are displayed for the explana-tion. In reality only, the selected contents are indicated. • When turning on the leak breaker at th...
Page 35 - Operation section
– 35 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E Operation section Push each button to select a desired operation. • The details of the operation needs to be set up once, afterward, the air conditioner can be used by pushing button only. 1 Air volume select button S...
Page 36 - Stop; Push; CORRECT USAGE; Preparation; Turn on the main power switch and/or the leakage breaker.
– 36 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E 1 Push button. The operation lamp goes on, and the operation starts. 2 Select an operation mode with the “MODE” button. One push of the button, and the displaychanges in the order shown on the right. • In HEAT mode, i...
Page 37 - Start; button; NOTE; When restarting the operation after stop
– 37 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E AUTOMATIC OPERATION (Auto Changeover) When you set the air conditioner in mode or switch over from AUTO operation because of some settings change, it will automatically select either cooling, heating, or fan only oper...
Page 38 - In FAN operation; ADJUSTMENT OF WIND DIRECTIONd; How to set up the wind direction; In HEAT operation; How to start swinging; How to stop swinging
– 38 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E UNIT SET CL In FAN operation In all modes Display when stopping the swing Initial setup Series of operation Fan/Heat operation Cool/Dry operation ADJUSTMENT OF WIND DIRECTIONd • When the air conditioner stops, the fla...
Page 39 - TIMER OPERATION; Timer operation; Push TIMER SET button.; Cancel of timer operation
– 39 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E TIMER OPERATION A type of timer operation can be selected from the following three types. OFF timer : The operation stops when the time of timer has reached the set time. Repeat OFF timer : Every time, the operation s...
Page 40 - HINTS FOR ECONOMICAL OPERATION; Never open doors and windows more often than necessary; In cooling, close the curtains to avoid direct sunlight.; Get uniform circulation of room air
– 40 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E HINTS FOR ECONOMICAL OPERATION Maintain room temperature at comfortable levelClean air filters The clogged air filter impairs the performance of the air conditioner. Never open doors and windows more often than necess...
Page 41 - If you do not plan to use the unit for more than 1 month; • Operate “FAN ONLY” mode with set temperature 30°C.; Checks before operation; FAN ONLY operation or; MAINTENANCE; Cleaning of remote controller
– 41 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E If you do not plan to use the unit for more than 1 month (1) Operate the fan for 3 to 4 hours to dry inside the unit • Operate “FAN ONLY” mode with set temperature 30°C. (2) Stop the air conditioner and turn off the m...
Page 42 - AIR CONDITIONER OPERATIONS AND PERFORMANCE; Power failure during operation will stop the unit completely.
– 42 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E AIR CONDITIONER OPERATIONS AND PERFORMANCE 3 minutes protection function 3-minutes protection function prevents the air conditioner from star ting for initial 3 minutes after the mainpower switch/circuit breaker is tu...
Page 43 - Do not install the air conditioner in the following places; TROUBLES AND CAUSES
– 43 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E RE-INSTALLATION DANGER Ask the dealer or an installation professional to re-install the air conditioner to a new place ormove it to another place and to observe the following items. If the air conditioner is inappropr...
Page 44 - Inoperative; These are not failures.
– 44 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E Calm Before you ask for servicing or repairs, check the following points. Inoperative • The main power switch is turned off. • The circuit breaker is activated to cut off power supply. • The main power fuse has blown ...
Page 45 - WARNINGS ABOUT OPERATION
– 45 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E ACCESSORIES (SOLD SEPARATELY) Remote controller PRECAUTIONS FOR SAFETY WARNING WARNINGS ABOUT INSTALLATION • Make sure to ask the qualified installation professional in electric work to install the air conditioner.If the air conditi...
Page 47 - Outdoor unit; Air outlet; XXX
– 47 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E PARTS NAME REMOTE CONTROLLER Air inlet (Side and rear) Pipes and electric wires Outdoor unit Air outlet Indoor unit Connecting duct Supply air grille NOTE :Parts marked with indicate the locally procured parts. XXX Supply air chambe...
Page 52 - Clear of timer operation
– 52 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E TIMER OPERATION A type of timer operation can be selected from the following three types. OFF timer : The operation stops after the set time has passed. Repeat OFF timer : Every time, the operation stops after the set time has passe...
Page 53 - Do not open doors and windows more often than necessary
– 53 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E HINTS FOR ECONOMICAL OPERATION Maintain room temperature at comfortable levelClean air filters Airflow and performance are reduced if the air filters become blocked. Do not open doors and windows more often than necessary To keep co...
Page 57 - Rec
– 57 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E Calm Before you ask for servicing or repairs, check the following points. Inoperative • The main power switch is turned off. • The circuit breaker is activated to cut off power supply. • The main power fuse has blown out. • Stoppage...
Page 58 - TROUBLES AND CAUSES (Concerning Remote Controller); Setting Change is Impossible; AUTO; • Check whether the MODE indi-; Reason and Disposal
– 58 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E TROUBLES AND CAUSES (Concerning Remote Controller) Before you ask for servicing or repairs, check the following points: Setting Change is Impossible Symptoms The fan speed can not bechanged. Causes • Check whether the MODE indi- cat...
Page 66 - ADJUSTMENT OF WIND DIRECTION
– 66 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E UNIT SET CL In FAN operation In all modes Display when stopping the swing Initial setup Series of operation Fan/Heat operation Cool/Dry operation ADJUSTMENT OF WIND DIRECTION • When the air conditioner stops, the flap (adjustment pl...
Page 74 - Accessory parts and Parts to be procured locally; Accessory parts
– 74 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E Accessory parts and Parts to be procured locally H Accessory parts H Parts to be procured locally Connecting pipe (Liquid side)(6.4mm (diam.), Nominal (diam.) 1/4” thick 0.8mm)RAV-SM560UT-E (9.5mm (diam.), Nominal (di...
Page 75 - To Disconnect the Appliance from Main Power Supply.; WARNINGS
– 75 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E 1 PRECAUTIONS FOR SAFETY • Ensure that all Local, National and International regulations are satisfied. • Read this “PRECAUTIONS FOR SAFETY” carefully before Installation. • The precautions described below include the...
Page 76 - forces applied to the terminals from affecting the terminals.
– 76 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E 1 PRECAUTIONS FOR SAFETY • After unpacking the unit, examine it carefully if there are possible damage. • Do not install in a place that might increase the vibration of the unit. • To avoid personal injury (with sharp...
Page 77 - Installation space; SELECTION OF INSTALLATION PLACE; • Install the air conditioner at a height 2.5m or more from the floor.; • Place where the unit can be installed horizontally.; Avoid installing in the following places.; • Place where organic solvent is used nearby.
– 77 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E Installation space Secure the specified space in the figure for installation and servicing. 2 SELECTION OF INSTALLATION PLACE WARNING • Install the air conditioner at enough strong place to withstand the weight of the...
Page 78 - Selection of installation place; Unit is installed inside the ceiling with slated roof.; Advice; • When using the air conditioner with 2-way discharge; Discharge direction; Height list of ceiling possible to be installed; • To change discharge direction, use a shielding
– 78 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E Selection of installation place In case of continued operation of the indoor unit underhigh-humidity conditions as described below, dew maycondense and water may drop. Especially, high-humidity atmosphere (dew pointte...
Page 81 - • Pull out the remote controller cord together with the
– 81 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E REQUIREMENT Before installation of the indoor unit, be sure toremove the cushion for transportation between thefan and the bell mouth. Running the unit withoutremoving the cushion may damage the fan motor. Installatio...
Page 82 - DRAIN PIPING WORK; • Following the Installation Manual,; Flexible hose
– 82 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E 3 DRAIN PIPING WORK Drain pipe connecting port (Hard socket) Attached hose band Attached flexible hose Soft socket Hard socket Socket for VP25(To be local procure) VP25 vinyl chloride pipe (To be local procure) Socket...
Page 83 - Connection procedure; Connect a socket and a hard vinyl chloride pipe.; Perform heat insulating.; Drain up
– 83 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E Connection procedure Connect a socket and a hard vinyl chloride pipe. • Using adhesive agent for vinyl chloride pipe, connect the drain pipes certainly so that water does not leak. • It takes approx. 10 hours to dry a...
Page 84 - REFRIGERANT PIPING AND EVACUATING; Refrigerant Piping; IMPORTANT 4 POINTS FOR PIPING WORK; Permissible Piping Length and Heat; • Tightening torque of flare pipe connections
– 84 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E 4 REFRIGERANT PIPING AND EVACUATING Refrigerant Piping 1. If the outdoor units are to be mounted on a wall, make sure that the supporting platform issufficiently strong. The platform should bedesigned and manufactured...
Page 85 - Piping with outdoor unit; • Shape of valve differs according to the outdoor unit.; • Never use the refrigerant sealed in the outdoor unit; Refrigerant amount to be added; • Charging an excessive or too little amount of; Open the valve fully; Thermal insulation process
– 85 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E Piping with outdoor unit • Shape of valve differs according to the outdoor unit. For details of installation, refer to the InstallationManual of the outdoor unit. Air purge Using a vacuum pump, perform vacuuming from ...
Page 86 - Remote controller wiring
– 86 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E 5 ELECTRICAL WORK WARNING 1. Using the specified cables, ensure to connect the wires, and fix wires securely so that the external tension to the cables do not affect the connecting part of the terminals. Incomplete co...
Page 87 - • Mount the cover of the electric parts box without pinching cables.; ; Cabling on the ceiling panel
– 87 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E Cable connection REQUIREMENT • Be sure to connect the cables matching the terminal numbers. Incorrect connection causes a trouble. • Be sure to pass the cables through the bushing of cabling connection port of the ind...
Page 88 - Cabling; Remote Controller Cabling; Cabling diagram; Wiring diagram
– 88 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E Cabling 1. Remove a screw and then remove cover of the electric parts box. 2. Strip wire ends (10 mm). 3. Match wire colors with terminal numbers on indoor and outdoor units’ terminal blocks and firmly screwwires to t...
Page 89 - In case of wired remote controller; TEST RUN; Before test run; or more exists between the terminal block 1 to 3 and the earth.; How to execute a test run
– 89 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E NOTE Do not use the forced test run for cases otherthan the test run because it applies anexcessive load to the devices. In case of wired remote controller TEST UNIT SET CL 1, 5 3 2, 4 Procedure 1 2 3 4 5 Description ...
Page 90 - TROUBLESHOOTING; Confirmation and check; The check code is only displayed during the operation.; Confirmation of error history; Check the troubles according to the above procedure.
– 90 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E 7 TROUBLESHOOTING Confirmation and check When a trouble occurred in the air conditioner, thecheck code and the indoor unit No. appear on thedisplay part of the remote controller. The check code is only displayed durin...
Page 91 - Before maintenance, be sure to turn off the leakage breaker.; Cleaning of air filter; Cleaning of panel and air filter; • Carefully rinse the panel and air filter to wash out the detergent.; Cleaning of Air Filters; • If the air filters are not cleaned, it not only reduce the cooling; Cleaning of discharge flap; Be careful to the direction of the flap when mounting.
– 91 – RAV-SP1100UT-E,RAV-SM560UT-E, RAV-SM800UT-E, RAV-SM1100UT-E, RAV-SM1400UT-E 8 MAINTENANCE Before maintenance, be sure to turn off the leakage breaker. Cleaning of air filter • If is displayed on the remote controller, maintain the air filter. • Clogging of the air filter reduce cooling/heatin...
Page 96 - INSTALLATION OF INDOOR UNIT; Installation procedure
– 96 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E 3 INSTALLATION OF INDOOR UNIT WARNING Install the air conditioner certainly at a place to sufficiently withstand the weight. If the strength is insufficient, the unit may fall down resulting in human injury. Perform a specified inst...
Page 97 - Therefore, check the relational position in the following figure.; • Dimension
– 97 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E External view REQUIREMENT The hanging bolt pitch on horizontal direction (B) is not halved at center with the ceiling opening size. Therefore, check the relational position in the following figure. • Dimension RAV-SM561BT RAV-SM801B...
Page 98 - Hanging down of indoor unit; • Adjustment of hanging bolt length and nut; • Clamp mounting; ) Required those other than M10 flat washer at site.
– 98 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E 1. Hanging down of indoor unit Refer to installation figures of hanging material andhanging bolt. • Adjustment of hanging bolt length and nut position Adjust hanging bolt length and nut position asshown in the figure before hanging ...
Page 99 - • Opening area of the return grille should be larger than; Quality of supplying grilles; Restriction to installation; Installation clearance; • As shown in the figure, keep clearance around the indoor unit.
– 99 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E Concealed duct type Ledge ceiling concealed duct type NOTE: • Opening area of the return grille should be larger than the one for suction port (Air filter) of the indoor unit. Channel Supply chamber Supply grille Supplying Supplying...
Page 100 - Static pressure characteristics of each model; AIR DUCTING WORK
– 100 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E Static pressure characteristics of each model 4 AIR DUCTING WORK Fig. 2 RAV-SM561BT (Square duct) Fig. 1 RAV-SM561BT (Round duct) Fig. 3 RAV-SM801BT (Round duct) Fig. 4 RAV-SM801BT (Square duct) 140 120 100 80 60 40 20 0500 700 780...
Page 102 - Installation reference; or; Connecting method of the duct
– 102 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E Installation reference (Example for RAV-SM801BT model) The air supply ducting work is classified in two ways, one is branched by the round ducts, and the other is branchedby the square ducts. (Be sure to divide the air supply duct ...
Page 103 - General cautions
– 103 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E Connecting method of the duct 1. Supply air side <Round duct> 1. Make the round duct according to inner dimension of the flange Use a glass wool board with inside/outside finishing25mm-thickness and 24kg/m³-density. 2. Connec...
Page 104 - Hanging of indoor unit; • Hook nut of the hanging bolt to the groove of the hanging metal on; Mounting of filter and canvas for suction port
– 104 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E 4 AIR DUCTING WORK Hanging of indoor unit Lift up the unit with a lifter, etc., and set the hanging metal in thehanging bolt. • Hook nut of the hanging bolt to the groove of the hanging metal on the main unit. • Using the level, et...
Page 105 - Piping material
– 105 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E 5 DRAIN PIPING WORK Piping material • For laying pipes underground, use hard vinyl chloride pipe. VP25 (Inner diamater Ø32mm) Piping and cautions • Set drain side of pipe at downward slope. (1/100 or more) • Be sure to apply therma...
Page 106 - After electric piping work
– 106 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E As long as possible (Approx. 100mm) VP 30 or more Downward grading 1/100 or more VP 30 VP 30 VP 30 Less than 20m Extended ventilating pipe Drain-up If down-slope cannot be set on a drain pipe, drain-up ispossible. • Set the height ...
Page 107 - Refrigerant piping; Permissible piping length and heat
– 107 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E 6 REFRIGERANT PIPING AND EVACUATING Refrigerant piping 1. If the outdoor units are to be mounted on a wall, make sure that the supporting platform issufficiently strong. The platform should bedesigned and manufactured to maintain i...
Page 109 - CAUTIONS; • Be sure connect earth wire.; Connect the connecting cable to the terminal as
– 109 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E 7 ELECTRICAL WORK NOTE: For selection and connection method of the power supply cords, refer to the details in the Installation Manual of theoutdoor unit. CAUTIONS • Be sure connect earth wire. Do not connect the earth wire to gas ...
Page 113 - APPLICABLE CONTROLS; NOTIFICATION; • Automatic address; Exchange of applicable control setup; Change the setup while operation of the equipment stops.
– 113 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E 10 APPLICABLE CONTROLS NOTIFICATION When using the equipment at the first time, it will take a lot of time that the remote controller accepts anoperation after power was on. However, it is not a trouble. • Automatic address • While...
Page 114 - Setup of external static pressure; To incorporate a filter sold separately; • For the item code in Procedure; • Select with shifting of the short plug on the; • Short plug position
– 114 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E Setup of external static pressure Matching with the resistance (External static pressure)of the duct to be connected, be sure to set up the tapexchange according to the basic operation procedure ( 1 → 2 → 3 → 4 → 5 → 6 ). • For the...
Page 115 - Check and test operation
– 115 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E Change of lighting time of filter sign According to the installation condition, the lighting timeof the filter sign (Notification of filter cleaning) can bechanged. Follow to the basic operation procedure ( 1 → 2 → 3 → 4 → 5 → 6 )....
Page 116 - Cleaning of Return grille; • Carefully rinse the Return grille to wash out the detergent.; the air conditioner such as water drops.; INSTALLATION/SERVICING TOOLS
– 116 – RAV-SM561BT-E, RAV-SM801BT-E, RAV-SM1101BT-E, RAV-SM1401BT-E 12 MAINTENANCE Cleaning of Return grille Preparation : 1. Turn off the main power supply switch (or breaker) before the unit maintenance. 2. Dismount the Return grille. Clean the Return grilles with water: • Wipe down the Return gr...
Page 117 - Parts to be procured locally
– 117 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E Accessory parts and Parts to be procured locally r Accessory parts <Separate sold parts> Part name Standard wiredremote controller Q’ty 1 Shape Usage ModelRBC-AMT21E Part name Owner’s Man ual Installation Manual Installation ...
Page 121 - Height of ceiling; List of installable ceiling height; Removal of suction grille; Peel out the protective vinyl on the level flap.; Removal of protector; In case of wireless type; • To prevent malfunction, select a place where is not
– 121 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E Height of ceiling Set the installable height of the ceiling within 4m,otherwise the air distribution will become poor. If height of ceiling exceeds 3.5m, hot air becomesdifficult to reach the floor surface, and then the changeof se...
Page 122 - How to use attached installation pattern; * As an error to some degree may generate on the
– 122 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E External view REQUIREMENT Strictly comply with the following rules to prevent damage of the indoor units and human injury. • Do not put a heavy article on the indoor unit. (Even units are packaged) • Carry in the indoor unit as it ...
Page 123 - Installation of hanging bolts; • Decide installation place of the unit and draw-out; Knockout hole of power cable take-in port; Pipe knockout hole; • In case of taking pipe from the rear side; • In case of taking pipe from left side; * Cut off the groove section with a metal saw or; • In case of taking pipe from upper side
– 123 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E Installation of hanging bolts Use M10 hanging bolts (4 pcs, to be local procure).Matching to the existing structure, set pitch accordingto size in the unit external view as shown below. Draw-out direction of pipe/cable • Decide ins...
Page 124 - Installation of indoor unit; • Preparation before holding down main unit; • Holding down of main unit; • The ceiling surface may not be
– 124 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E Installation of indoor unit • Preparation before holding down main unit * Confirm the presence of the ceiling material beforehand because the fixing method of hangingmetal when the ceiling material is set differs fromthat when the ...
Page 125 - Piping/Heat insulating material
– 125 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E 3 DRAIN PIPING WORK REQUIREMENT • Be sure to perform heat insulation of the drain pipes of the indoor unit. • Never forget to perform heat insulation of the connecting part with the indoor unit. An incomplete heat insulation causes...
Page 126 - • In case of taking pipe from the left side
– 126 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E Drain pipe Refrigerant pipe Drain pipe Connection of drain hose • Insert the attached drain hose into the drain pipe connecting port on the drain pan up to the end. • Fit the attached hose band to the end of the pipe connecting por...
Page 127 - Tightening connection
– 127 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E 4 REFRIGERANT PIPING AND EVACUATING Refrigerant Piping • The connecting sections of the refrigerant pipes are provided at the positions in the figure below. +0- 0.4 B A Imperial (Wing nut type) • Flaring diam. meter size : A (Unit ...
Page 129 - Incomplete connection or fixation may cause a fire, etc.; • This indoor unit has no power cord.; The coating may melt resulting in an accident.; -core non polarity cable is used for the remote controller wiring.
– 129 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E 5 ELECTRICAL WORK WARNING 1. Using the specified cables, ensure to connect the wires, and fix wires securely so that the external tension to the cables do not affect the connecting part of the terminals. Incomplete connection or fi...
Page 135 - When using wireless remote controller; • Select by exchange of short plug on indoor
– 135 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E In case of installation to high ceiling When the height of the ceiling to be installed exceeds3.5m, adjustment of air volume is necessary. Set upthe high ceiling. • Set according to the basic operation procedure ( 1 → 2 → 3 → 4 → 5...
Page 136 - Change of lighting time of filter sign; To secure better effect of heating
– 136 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E Change of lighting time of filter sign According to the installation condition, the lighting timeof the filter sign (Notification of filter cleaning) can bechanged. Follow to the basic operation procedure ( 1 → 2 → 3 → 4 → 5 → 6 )....
Page 137 - Clean the Return grilles with water:; • Wipe down the Suction grille with a sponge or towel; • Carefully rinse the Return grille to wash out the; • Do not start the air conditioner while leaving the; • If the air filters are not cleared, it not only impairs the; before the unit maintenance.; Removal of suction grille
– 137 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E 9 INSTALLATION/SERVICING TOOLS Tools 10 MAINTENANCE Cleaning of Return grille Preparation : 1. Turn off the main power supply switch (or breaker) before the unit maintenance. 2. Dismount the Suction grille. Clean the Return grilles...
Page 138 - Open the suction grille
– 138 – RAV-SM561CT-E, RAV-SM801CT-E, RAV-SM1101CT-E, RAV-SM1401CT-E Cleaning of air filter • [FILTER] is displayed on the remote controller, maintain the air filter. • Clogging of the air filter decreases the cooling/heating effect. • After cleaning, push [ ]. [FILTER] display disappears. ○ ○ ○ ○ ○...
Toshiba 26C100U
User Manual
Toshiba 55SL412U
User Manual
Toshiba 50L5200U
User Manual
Toshiba 24V4210U
User Manual
Toshiba 40L3400U
User Manual
Toshiba 50L1350U
User Manual
Toshiba 24SLV411U
User Manual
Toshiba 50L2400U
User Manual
Toshiba 58L7350U
User Manual
Toshiba 50L1400U
User Manual