Toshiba M10- Manuals

Satellite Pro M10 Series Maintenance Manual (960-431) v Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following the...

vi Satellite Pro M10 Series Maintenance Manual (960-431)

Satellite Pro M10 Series Maintenance Manual (960-431) vii Table of Contents Chapter 1 Hardware Overview 1.1 Features .................................................................................................................... 1-1 1.2 System Unit Block Diagram ...................................

viii Satellite Pro M10 Series Maintenance Manual (960-431) Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................. 3-1 3.2 Executing the Diagnostic Test ....................................................

Satellite Pro M10 Series Maintenance Manual (960-431) ix Chapter 4 Replacement Procedures 4.1 General ..................................................................................................................... 4-1 4.2 Memory Modules ............................................................

x Satellite Pro M10 Series Maintenance Manual (960-431) 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) .................................. 4-126 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) ..................................... 4-136 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) .............

1 Hardware Overview 1-ii Satellite Pro M10 Series Maintenance Manual (960-431)

1 Hardware Overview Satellite Pro M10 Series Maintenance Manual (960-431) 1-iii Chapter 1 Contents 1.1 Features.......................................................................................................................1-1 1.2 System Unit Block Diagram........................................

1 Hardware Overview 1-iv Satellite Pro M10 Series Maintenance Manual (960-431) Figures Figure 1-1 Front of the computer .....................................................................................1-6 Figure 1-2 System unit configuration..........................................................

1 Hardware Overview 1.2 System Unit Block Diagram 1-8 Satellite Pro M10 Series Maintenance Manual (960-431) 1.2 System Unit Block Diagram Figure 1-3 is a block diagram of the system unit. IMVP4 (Voltage Regulator) ADM1032 (Thermal senser) CPU: Intel Pentium M1.3, 1.4, 1.5, 1.6 GHz Micro FCPGA CK 408...

1 Hardware Overview 1.3 3.5-inch Floppy Disk Drive 1-14 Satellite Pro M10 Series Maintenance Manual (960-431) 1.3 3.5-inch Floppy Disk Drive The external USB 3.5-inch FDD is a thin, high-performance reliable drive that supports 720KB (formatted) 2DD and 1.44MB (formatted) 2HD disks. The FDD is shown...

1.4 2.5-inch Hard Disk Drive 1 Hardware Overview Satellite Pro M10 Series Maintenance Manual (960-431) 1-15 1.4 2.5-inch Hard Disk Drive The removable HDD is a random-access, non-volatile storage device. It has a non-removable 2.5-inch magnetic disk and mini-Winchester type magnetic heads. The compu...

1 Hardware Overview 1.5 DVD-ROM Dvive 1-16 Satellite Pro M10 Series Maintenance Manual (960-431) 1.5 DVD-ROM Drive The DVD-ROM drive is capable of driving either 12cm (4.72-inch) or 8cm (3.15-inch) DVD/CDs without an adaptor. It reads DVDs at maximum 8-speed and reads CDs at maximum 24-speed. The DV...

1.6 Multi Drive 1 Hardware Overview Satellite Pro M10 Series Maintenance Manual (960-431) 1-17 1.6 Multi Drive The Multi drive accommodates either 12cm (4.72-inch) or 8cm (3.15-inch) CDs and CD-R/RWs or DVDs. It reads DVDs at a maximum 8-speed and CDs at a maximum 24-speed. The Multi drive is shown ...

1 Hardware Overview 1.6 Multi Drive 1-18 Satellite Pro M10 Series Maintenance Manual (960-431) Table 1-4 Multi drive specifications (2/2) TEAC DW-224E-36 Item DVD-ROM (Play mode) CD-ROM (Play mode) CD-R/CD-RW (Record mode) ATAPI Burst (Mbytes/s) 33.3 (Ultra DMA mode 2) 16.7 (PIO Mode 4, Multi word D...

1.7 DVD Multi Drive 1 Hardware Overview Satellite Pro M10 Series Maintenance Manual (960-431) 1-19 1.7 DVD Multi Drive The DVD Multi drive (Panasonic UJ-810BTJ7-A) is capable of driving either 12cm (4.72-inch) or 8cm (3.15-inch) DVD/CDs without an adaptor. The DVD Multi drive is shown in Figure 1-8....

1 Hardware Overview 1.8 Power Supply 1-20 Satellite Pro M10 Series Maintenance Manual (960-431) 1.8 Power Supply The power supply distributes 11 different voltages to the system board and performs the following functions: 1. A/D conversion The power supply controller (PSC) uses 10-bit sampling for A...

1 Hardware Overview 1.8 Power Supply 1-22 Satellite Pro M10 Series Maintenance Manual (960-431) The power supply output rating is specified in Table 1-6. Table 1-6 Power supply board output rating Power supplied Yes/No Use Name Voltage (V) Stand by Power off No battery CPU (core) PPV 1.3 No No No CP...

1.9 Batteries 1 Hardware Overview Satellite Pro M10 Series Maintenance Manual (960-431) 1-23 1.9 Batteries The computer has three types of batteries: Main battery pack Optional secondary battery pack (installed in the Slim Select Bay) RTC battery The battery specifications are listed in Table 1-7. T...

1 Hardware Overview 1.9 Batteries 1-24 Satellite Pro M10 Series Maintenance Manual (960-431) 1.9.3 Battery Charging Control Battery charging is controlled by a power supply microprocessor mounted on the system board. The power supply microprocessor controls whether the charge is on or off and detect...

1.9 Batteries 1 Hardware Overview Satellite Pro M10 Series Maintenance Manual (960-431) 1-25 Detection of full charge A full charge is detected when the battery is charging, and under any of the following conditions: 1. The battery charging current drops under the predetermined limit. 2. The chargin...

2 Troubleshooting Procedures 2-ii Satellite Pro M10 Series Maintenance Manual (960-431)

2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-iii Chapter 2 Contents 2.1 Troubleshooting ......................................................................................................... 2-1 2.2 Troubleshooting Flowchart ...................................

2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-3 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide for determining which troubleshooting procedures to execute. Before going through the flowchart steps, verify ...

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-7 2.3 Power Supply Troubleshooting The power supply controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and conti...

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-8 Satellite Pro M10 Series Maintenance Manual (960-431) Table 2-2 DC IN LED DC IN LED Power supply status Lights green DC power is being supplied from the AC adaptor. Blinks orange Power supply malfunction*3 Doesn’t light Any condition ...

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-9 Procedure 2 Error Code Check If the power supply microprocessor detects a malfunction, the DC IN LED blinks orange. The blink pattern indicates an error as shown below. Start Off f...

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-10 Satellite Pro M10 Series Maintenance Manual (960-431) 1st Battery Error code Meaning 20h Main battery overvoltage is detected. (Not supported) 21h Main battery charge current is more than 6.05 A. 22h Main battery discharge current is...

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-15 Procedure 3 Connection Check The power supply wiring diagram is shown below: AC adaptor System board PJ8800 AC power cord AC adaptor cord Main battery pack Slim Select Bay PJ8810 ...

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 2-16 Satellite Pro M10 Series Maintenance Manual (960-431) Procedure 4 Quick Charge Check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn...

2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-17 Procedure 5 Replacement Check The system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and pe...

2 Troubleshooting Procedures 2.4 System Board Troubleshooting 2-18 Satellite Pro M10 Series Maintenance Manual (960-431) 2.4 System Board Troubleshooting This section describes how to determine if the system board is defective or not functioning properly. Start with Procedure 1 and continue with the...

2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-19 Procedure 1 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. The IRT tests each IC on the system board ...

2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-21 Procedure 2 Printer Port LED Check on Boot Mode The printer port LED displays the IRT status and test status by turning lights on and off as an eight-digit binary value for boot m...

2.4 System Board Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-29 Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. Refer to Chapter 3, Tests and Diagnostics, for more information on h...

2 Troubleshooting Procedures 2.5 FDD Troubleshooting 2-30 Satellite Pro M10 Series Maintenance Manual (960-431) 2.5 FDD Troubleshooting This section describes how to determine if the FDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedur...

2.5 FDD Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-31 Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the FDD, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more infor...

2 Troubleshooting Procedures 2.5 FDD Troubleshooting 2-32 Satellite Pro M10 Series Maintenance Manual (960-431) Procedure 3 Connector Check and Replacement Check The 3.5-inch FDD is connected to the USB board. Check 1 Make sure that the FDD cable is firmly connected to the USB port, and that the USB...

2.6 HDD Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-33 2.6 HDD Troubleshooting This section describes how to determine if the HDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedur...

2 Troubleshooting Procedures 2.6 HDD Troubleshooting 2-34 Satellite Pro M10 Series Maintenance Manual (960-431) Procedure 2 Partition Check Insert the TOSHIBA MS-DOS system disk and restart the computer. Perform the following checks: Check 1 Type C: and press Enter . If you cannot change to drive C,...

2.6 HDD Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-35 Procedure 3 Format Check The computer’s HDD is formatted using the MS-DOS FORMAT program. To format the HDD, follow the steps below. Check 1 Format the HDD and transfer system files using ...

2.6 HDD Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-37 Procedure 5 Connector Check and Replacement Check The HDD or the system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replaceme...

2.7 Keyboard Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-39 Procedure 3 Connector and Replacement Check The keyboard, Touch pad, switch board or system board may be disconnected or damaged. Disassemble the computer following the steps describe...

2 Troubleshooting Procedures 2.8 Display Troubleshooting 2-42 Satellite Pro M10 Series Maintenance Manual (960-431) Procedure 3 Connector and Replacement Check The FL, FL inverter board, LCD module, and system board are connected to the display circuits. Any of these components may be damaged. Refer...

2.9 Optical Disk Drive Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-43 2.9 Optical Disk Drive Troubleshooting This section describes how to determine if the computer’s internal optical disk drive (CD-R/RW drive, DVD-ROM drive, Multi drive, DVD-...

2 Troubleshooting Procedures 2.9 Optical Disk Drive Troubleshooting 2-44 Satellite Pro M10 Series Maintenance Manual (960-431) Procedure 3 Connector Check and Replacement Check The optical disk drive is installed in the system board. The drive may be disconnected, or the drive or system board may be...

2.10 Modem Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-45 2.10 Modem Troubleshooting This section describes how to determine if the computer's modem is functioning properly. Perform the steps below starting with Procedure 1 and continuing with...

2.11 LAN Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-47 2.11 LAN Troubleshooting This section describes how to determine if the computer's LAN port is functioning properly. Perform the steps below starting with Procedure 1 and continuing with ...

2 Troubleshooting Procedures 2.11 LAN Troubleshooting 2-48 Satellite Pro M10 Series Maintenance Manual (960-431) Procedure 2 Connector Check and Replacement Check If the LAN port malfunctions, there may be a bad connection between the RJ-45/RJ-11 jacks and the System Board. Or the System Board may b...

2.12 Sound Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-49 2.12 Sound Troubleshooting This section describes how to determine if the computer's sound functions are functioning properly. Perform the steps below starting with Procedure 1 and cont...

2 Troubleshooting Procedures 2.12 Sound Troubleshooting 2-50 Satellite Pro M10 Series Maintenance Manual (960-431) Procedure 2 Connector Check The sound function wiring diagram is shown below: System board Right Speaker PJ5006 Sound board Right speaker cable PJ5007 PJ5004 PJ5005 Left speaker cable L...

2.12 Sound Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-51 Procedure 3 Replacement Check Check 1 If the stereo speakers don't sound properly, the stereo speakers may be defective or damaged. Replace them with new ones. If the stereo speakers st...

2 Troubleshooting Procedures 2.13 Bluetooth Troubleshooting 2-52 Satellite Pro M10 Series Maintenance Manual (960-431) 2.13 Bluetooth Troubleshooting This section describes how to determine if the computer's Bluetooth functions are working properly. Perform the steps below starting with Procedure 1 ...

2 Troubleshooting Procedures 2.14 Wireless LAN Troubleshooting 2-54 Satellite Pro M10 Series Maintenance Manual (960-431) 2.14 Wireless LAN Troubleshooting This section describes how to determine if the computer's Wireless LAN is functioning properly. Perform the steps below starting with Procedure ...

2.14 Wireless LAN Troubleshooting 2 Troubleshooting Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 2-55 Procedure 2 Connector Check and Replacement Check If the Wireless LAN port malfunctions, there may be a bad connection between the antenna boards, the Wireless LAN Mini PCI card,...

3 Tests and Diagnostics 3-ii Satellite Pro M10 Series Maintenance Manual (960-431)

3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-iii Chapter 3 Contents 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test ......................................

3 Tests and Diagnostics 3-iv Satellite Pro M10 Series Maintenance Manual (960-431) 3.25.2 Operations .......................................................................................... 3-69 3.26 Floppy Disk Drive Utilities..........................................................................

3.1 The Diagnostic Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-1 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test program to test the functions of the computer’s hardware modules. The Diagnostic Test Program is stored on the Diag...

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-3 3.2 Executing the Diagnostic Test Toshiba MS-DOS is required to run the DIAGNOSTICS TEST PROGRAM. To start the DIAGNOSTIC TEST PROGRAM, follow these steps: 1. Insert the Diagnostics di...

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-4 Satellite Pro M10 Series Maintenance Manual (960-431) 2. To execute the DIAGNOSTIC TEST MENU from the DIAGNOSTICS MENU, set the highlight bar to 1 , and press Enter . The following DIAGNOSTIC TEST MENU will appear: TOSHIBA Personal Comput...

3.2 Executing the Diagnostic Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-5 3. Select the option you want to execute and press Enter . When “1-SYSTEM TEST” is selected, the following message will appear: SUB-TEST MENU : 01 - ROM checksum02 - Dock/Undock03 - 04...

3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-6 Satellite Pro M10 Series Maintenance Manual (960-431) 5. The following message will appear: ERROR STOP : YES/NO Then, use the left or right arrow keys to move the cursor to the desired option and press Enter . Selecting YES stops the test...

3.3 Subtest Names 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-7 3.3 Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/3) No. Test Name Subtest No. Subtest Name 1 SYSTEM 01 02 04 05 06 07 0...

3.3 Subtest Names 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-9 Table 3-1 Subtest names (3/3) No. Test Name Subtest No. Subtest Name - Wireless LAN (Agere) 1 2 3 0 Transmit & Receive test [Responder] MAC Address test [Mini-PCI Wireless LAN] Wireless LAN (WEP64...

3 Tests and Diagnostics 3.4 System Test 3-10 Satellite Pro M10 Series Maintenance Manual (960-431) 3.4 System Test To execute the System Test select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and pre...

3 Tests and Diagnostics 3.4 System Test 3-12 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 10 CPU Temperature This subtest measures the CPU temperature to see if the cooling functions of the computer are effectively working. When the subtest starts, the following message appears on t...

3.5 Memory Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-13 3.5 Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and pr...

3.6 Keyboard Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-15 3.6 Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute ...

3 Tests and Diagnostics 3.6 Keyboard Test 3-16 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 02 Pressed Key Code Display When a key is pressed, the scan code, character code, and key top name are displayed on the screen in the format shown below. The Ins, Caps Lock , Num Lock, Scroll...

3 Tests and Diagnostics 3.6 Keyboard Test 3-18 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 05 USB Test ( Port0,Port1 ) test This Subtest checks USB. The USB TEST Module (ZD0003P01) and USB Cable (ZD0003P02) must be connected to the computer. The following message will appear. Selec...

3.7 Display Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-21 Subtest 04 Gradation & Mode test for VGA This subtest displays gradations for each mode. Execute the test, then press Enter to change the mode. The display below appears on the screen when this su...

3 Tests and Diagnostics 3.8 Printer Test 3-24 Satellite Pro M10 Series Maintenance Manual (960-431) 3.8 Printer Test To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The Printer Test contains three subtests that test the output...

3 Tests and Diagnostics 3.10 Hard Disk Test 3-28 Satellite Pro M10 Series Maintenance Manual (960-431) 3.10 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter , and follow the directions on the screen. The hard disk test contains ten subtests that test ...

3.10 Hard Disk Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-29 3. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press Enter . The following message will appear dur...

3 Tests and Diagnostics 3.10 Hard Disk Test 3-30 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 04 Cross Talk & Peak Shift This subtest writes eight types of worst pattern data (listed below) to a cylinder, then reads the data while moving from cylinder to cylinder. Worst pattern ...

3.11 Real Timer Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-31 3.11 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The real timer test contains three Subtests that t...

3 Tests and Diagnostics 3.13 Expansion Test 3-34 Satellite Pro M10 Series Maintenance Manual (960-431) 3 3.13 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The expansion test contains two subtests. NOTE: T...

3.14 CD-ROM/DVD-ROM Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-35 3.14 CD-ROM/DVD-ROM Test To execute the CD-ROM/DVD-ROM test, select 13 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The CD-ROM/DVD-ROM test contains six...

3.16 Wireless LAN Test (Agere) 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-37 3.16 Wireless LAN Test (Agere) This section describes how to perform the wireless LAN transmitting-receiving test with the test program. Note: Use another computer (with Agere wireless L...

3 Tests and Diagnostics 3.16 Wireless LAN Test (Agere) 3-38 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 01 Transmit & Receive test This sub test checks transmit and receive functions. Transmit test Press 1 to select the test and press Enter in the target machine as a responder....

3.16 Wireless LAN Test (Agere) 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-39 When the machine has passed the test, “OK” message will appear in the test machine. Then press Enter in the target machine; the “OK” message will appear also in the target machine. Press...

3.16 Wireless LAN Test (Agere) 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-41 Subtest 02 Mac Address test This subtest reads MAC Address. If there is no problem, the “OK” message will appear. Subtest 03 Wireless LAN (WEP64/128) test This subtest reads the WEP of t...

3.17 Wireless LAN Test (Atheros) 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-43 Setting the responder machine Note: Release the write-protection of the floppy disk for the test. Insert a floppy disk containing the test program into the FDD for the responder machin...

3 Tests and Diagnostics 3.17 Wireless LAN Test (Atheros) 3-44 Satellite Pro M10 Series Maintenance Manual (960-431) When the tester machine has passed the test, "OK" message will appear in the tester machine. Press Enter to return to the main menu. When the tester machine has not passed the ...

3 Tests and Diagnostics 3.18 Sound/LAN/Modem Test 3-48 Satellite Pro M10 Series Maintenance Manual (960-431) Subtest 03 LAN Test (a) Select 3 to execute and press Enter . The following message will appear: COMPLETED Repeat count = 00000 Error count = 00000 XXXX (XXXXX) LAN TEST Vol.X.XX 100Mbps Auto...

3.20 Bluetooth Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-53 Subtest 01 BD_ADDR check This subtest checks the BD_ADDR functions. When the Bluetooth test menu is displayed, press 1 to select the test and press Enter . The following message will appear: ------...

3 Tests and Diagnostics 3.20 Bluetooth Test 3-54 Satellite Pro M10 Series Maintenance Manual (960-431) If the target machine has any problem, it displays Error CODE . The following message is desplayed. ----------------------------------------------------------------------------- Bluetooth Subsystem...

3.20 Bluetooth Test 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-59 If the machine detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit. Error code Table 3-3 Error code for Bluetooth test (BD_ADDR...

3.21 Error Code and Error Status Names 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-61 3.21 Error Code and Error Status Names Table 3-4 lists the error codes and error status names for the Diagnostic Test. Table 3-4 Error codes and error status names (1/3) Device n...

3 Tests and Diagnostics 3.22 Hard Disk Test Detail Status 3-64 Satellite Pro M10 Series Maintenance Manual (960-431) 3.22 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test e...

3 Tests and Diagnostics 3.23 Head Cleaning 3-66 Satellite Pro M10 Series Maintenance Manual (960-431) 3.23 Head Cleaning 3.23.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this prog...

3.24 Log Utilities 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-67 3.24 Log Utilities 3.24.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk...

3.26 Floppy Disk Drive Utilities 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-71 3.26 Floppy Disk Drive Utilities 3.26.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE :...

3 Tests and Diagnostics 3.26 Floppy Disk Drive Utilities 3-72 Satellite Pro M10 Series Maintenance Manual (960-431) 3.26.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message: [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 - HDD ID READ 9 - EXIT TO ...

3.26 Floppy Disk Drive Utilities 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-73 3. COPY program (a) When COPY is selected, the following message appears: FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number will...

3 Tests and Diagnostics 3.26 Floppy Disk Drive Utilities 3-74 Satellite Pro M10 Series Maintenance Manual (960-431) 4. DUMP program (a) When DUMP is selected, the following message appears: DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) When FDD is select...

3.26 Floppy Disk Drive Utilities 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-75 5. HDD-ID READ Selecting HDD ID READ displays the following HDD ID configuration: [HDD ID Read (VX.XX)] [Drive #X] ID code (h) = XXXX No. of Cylinders = XXXX XXXX Removable Cylinders =...

3 Tests and Diagnostics 3.27 System Configuration 3-76 Satellite Pro M10 Series Maintenance Manual (960-431) 3 3.27 System Configuration 3.27.1 Function Description The System Configuration program contains the following configuration information for the computer: 1. Processor Type 2. VGA Controller...

3 Tests and Diagnostics 3.28 SETUP 3-80 Satellite Pro M10 Series Maintenance Manual (960-431) 3.28.2 Accessing the SETUP Program Selecting 0 from the DIAGNOSTICS MENU and pressing Enter displays the TSETUP screen. The TSETUP screen is divided into two pages: SYSTEM SETUP (1/2) and SYSTEM SETUP (2/2)...

3 Tests and Diagnostics 3.28 SETUP 3-82 Satellite Pro M10 Series Maintenance Manual (960-431) Moving Within the SETUP Menu and Changing Values 1. Press Å and Æ to move between the two columns. Press PgDn and PgUp to move between the two pages. Press ↑ and ↓ to move between items in a column. 2. Pres...

3.28 SETUP 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-83 SETUP Options The SETUP screen is divided into functionally related groups. This section describes each group and its options. 1. Memory This group of options displays the computer’s memory. (a) Total This ...

3.28 SETUP 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-87 (c) TV Type This option lets you make settings for television display. NTSC(US) (Default) NTSC(JAPAN) PAL 8. Others Whether or not you need to configure the computer with these options depends primarily on ...

3 Tests and Diagnostics 3.28 SETUP 3-88 Satellite Pro M10 Series Maintenance Manual (960-431) (c) Level 2 Cache Use this option to enable or disable the level 2 cache. Enabled Enables the level 2 cache. (Default) Disabled Disables the level 2 cache. (d) Dynamic CPU Frequency Mode Use this option to ...

3.28 SETUP 3 Tests and Diagnostics Satellite Pro M10 Series Maintenance Manual (960-431) 3-89 (f) Panel Power On/Off This option lets you set the Panel Power On/Off function. It is effective only in Resume mode. Enabled Enables the Panel Power On/Off. Disabled Disables the Panel Power On/Off (Defaul...

3 Tests and Diagnostics 3.28 SETUP 3-90 Satellite Pro M10 Series Maintenance Manual (960-431) COM level Interrupt level I/O address COM1 4 3F8H (Serial port default) COM2 3 2F8H COM3 4 3E8H COM3 5 3E8H COM3 7 3E8H COM4 3 2E8H COM4 5 2E8H COM4 7 2E8H Not Used Disables port (b) Parallel This option se...

3 Tests and Diagnostics 3.28 SETUP 3-92 Satellite Pro M10 Series Maintenance Manual (960-431) 14. Peripheral Use this option to select the parallel port mode and hard disk mode. (a) Internal Pointing Device This option enables and disables the Touch Pad and accupoint. Enabled Enables the Touch Pad a...

4 Replacement Procedures 4-ii Satellite Pro M10 Series Maintenance Manual (960-431)

4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-iii Chapter 4 Contents 4.1 General ....................................................................................................................... 4-1 Safety Precautions.............................................

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-1 4 p 4.1 General This section explains how to disassemble the computer and replace Field Replaceable Units (FRUs). It may not be necessary to remove all the FRUs in order to replace one. The chart below is ...

4 Replacement Procedures 4.1 General 4-2 Satellite Pro M10 Series Maintenance Manual (960-431) Safety Precautions Before you begin disassembly, read the following safety precautions and observe them carefully as you work. DANGER: 1. Always use the genuine battery that is authorized by TOSHIBA or com...

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-3 Before You Begin Look over the procedures in this section before you begin disassembling the computer. Familiarize yourself with the disassembly and reassembly steps. Begin each procedure by removing the A...

4 Replacement Procedures 4.1 General 4-4 Satellite Pro M10 Series Maintenance Manual (960-431) Disassembly Procedures The computer has three basic types of cable connectors: Pressure Plate Connectors Coaxial Cable Connectors Normal Pin Connectors To disconnect a Pressure Plate connector, lift up the...

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-5 Tools and Equipment The use of Electrostatic Discharge (ESD) equipment is very important for your safety and the safety of those around you. Proper use of these devices will increase the success rate of yo...

4 Replacement Procedures 4.1 General 4-6 Satellite Pro M10 Series Maintenance Manual (960-431) Screw Tightening Torque When you fasten screws, be sure to follow the torque list below. CAUTION: Overtightening can damage components and screws; undertightening can result in electrical shorts or other d...

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-7 Color of Screw Shaft To avoid mistakes on the screw length, screw shafts are colored as follows: ❑ Even number length screw: brown ❑ Odd number length screw: white ❑ Special length screw: blue Screws whose...

4 Replacement Procedures 4.1 General 4-8 Satellite Pro M10 Series Maintenance Manual (960-431) Removing the Battery Pack To remove the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: When handling battery packs, be careful not to short circuit the terminals. Also do not drop, ...

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-9 Installing the Battery Pack To install the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: The battery pack is a lithium ion battery, which can explode if not properly replaced, used...

4 Replacement Procedures 4.1 General 4-10 Satellite Pro M10 Series Maintenance Manual (960-431) Removing an Optional PC Card To remove a PC Card (option), follow the steps below and refer to Figure 4-2. CAUTION: Before you remove a PC Card, refer to the card's documentation and to your operating sys...

4.1 General 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-11 Removing an Optional SD Card To remove an SD card (option), follow the steps below and refer to Figure 4-3. CAUTION: Before you remove an SD card, refer to the card's documentation and to your operating s...

4 Replacement Procedures 4.2 Memory Modules 4-12 Satellite Pro M10 Series Maintenance Manual (960-431) 4.2 Memory Modules Removing a Memory Module To remove a memory module make sure the computer is in boot mode and powered off, follow the steps below and refer to Figures 4-4 and 4-5. CAUTION: Do no...

4.2 Memory Modules 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-13 4. Gently press out on two latches . One end of the memory module will pop up. 5. Grasp the memory module and pull it out. Latches Memory module Figure 4-5 Removing the memory modules

4 Replacement Procedures 4.2 Memory Modules 4-14 Satellite Pro M10 Series Maintenance Manual (960-431) Installing a Memory Module To install a memory module, make sure that the computer is in boot mode and powered off, follow the steps below and refer to Figures 4-4 and 4-5. CAUTION: Do not touch th...

4.3 HDD 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-15 4.3 HDD CAUTION : When handling the HDD, do not press the top surface as shown by the arrow. Hold it by the sides. Removing the HDD To remove the HDD, follow the steps below and refer to Figures 4-6 to 4-8. 1...

4 Replacement Procedures 4.3 HDD 4-16 Satellite Pro M10 Series Maintenance Manual (960-431) 4. Pull the HDD gently out of the slot. HDD Figure 4-7 Removing the HDD pack NOTE: The following steps describe how to disassemble the HDD pack; however, do not disassemble if the HDD is working properly.

4.3 HDD 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-17 5. Place the HDD pack on a flat surface, and remove four M3 × 4 silver flat-head screws . 6. Remove the HDD bracket . M3 × 4 silver flat-head screws M3 × 4 silver flat-head screws HDD HDD bracket Figure 4-8 R...

4 Replacement Procedures 4.3 HDD 4-18 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the HDD To install the HDD, follow the steps below and refer to Figures 4-6 to 4-8. CAUTION: Don't hold the HDD by its top and bottom flat surfaces. It may damage the HDD. 1. Seat the HDD in the br...

4.4 Slim Select Bay Module 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-19 4.4 Slim Select Bay Module Removing the Slim Select Bay Module To remove the slim select bay module, follow the steps below and refer to Figures 4-9 and 4-10. 1. If a screw ( M3 × 4 black f...

4.4 Slim Select Bay Module 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-21 Installing the Slim Select Bay Module To install the slim select bay module, follow the steps below and refer to Figures 4-9 and 4-10. 1. Seat the ODD in the ODD bracket . 2. Secure the ODD...

4 Replacement Procedures 4.5 Modem Daughter Card 4-22 Satellite Pro M10 Series Maintenance Manual (960-431) 4.5 Modem Daughter Card Removing the Modem Daughter Card To remove the modem daughter card (MDC), follow the steps below and refer to Figures 4-11 and 4-12. 1. Remove one M2.5 × 6 black flat-h...

4.5 Modem Daughter Card 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-23 3. Remove two M2 × 4 screws securing the MDC . 4. Carefully lift up the MDC to disconnect it from PJ2017 on the system board . 5. Carefully disconnect the modem cable from JP1 on the MDC . M2 ...

4 Replacement Procedures 4.5 Modem Daughter Card 4-24 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Modem Daughter Card To install the modem daughter card (MDC), follow the steps below and refer to Figures 4-11 and 4-12. 1. Carefully connect the modem cable to JP1 on the MDC ....

4.6 CPU 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-25 4.6 CPU Removing the CPU To remove the CPU, follow the steps below and refer to Figures 4-13 and 4-16. 1. Remove one M2.5 × 6 black flat-head screw and two M2.5 × 4 black flat-head screw securing the CPU/MDC ...

4 Replacement Procedures 4.6 CPU 4-26 Satellite Pro M10 Series Maintenance Manual (960-431) 3. Remove the cooling module . Cooling module Figure 4-14 Removing the cooling module 4. Turn the cam to the unlock position with a flat-blade screwdriver to unlock the CPU . LOCK OPEN Figure 4-15 Unlocking t...

4.6 CPU 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-27 5. Lift up the CPU . CPU Figure 4-16 Removing the CPU

4 Replacement Procedures 4.6 CPU 4-28 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the CPU To install the CPU, follow the steps below and refer to Figures 4-13 to 4-17. 1. Make sure the cam is in the open position. 2. Seat the CPU in the CPU socket , aligning the triangle mark on...

4.7 Keyboard 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-29 4.7 Keyboard Removing the Keyboard To remove the keyboard, follow the steps below and refer to Figures 4-18 to 4-21. 1. Open the display panel. 2. Insert your fingernails into notches in the keyboard bra...

4 Replacement Procedures 4.7 Keyboard 4-30 Satellite Pro M10 Series Maintenance Manual (960-431) 3. Remove two M2.5 × 2.6 black flat-head screws securing the keyboard. 4. Rotate out the keyboard and lay it on top of the palm rest. M2.5 × 2.6 black flat-head screws Keyboard Figure 4-19 Removing screw...

4.7 Keyboard 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-31 5. Remove one M2.5 × 16 black screw securing the metal plate to remove it. M2.5 × 16 black screws Metal plate Figure 4-20 Removing the metal plate

4 Replacement Procedures 4.7 Keyboard 4-32 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Disconnect the keyboard cable from PJ123 on the system board , and remove the keyboard . Keyboard Keyboard cable PJ123 Figure 4-21 Removing the keyboard

4.7 Keyboard 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-33 Installing the Keyboard To install the keyboard, follow the steps below and refer to Figures 4-18 to 4-21. 1. Lay the keyboard on the palm rest upside down. 2. Connect the keyboard cable to PJ123 on the ...

4 Replacement Procedures 4.8 Switch Board 4-34 Satellite Pro M10 Series Maintenance Manual (960-431) 4.8 Switch Board Removing the Switch Board To remove the switch board, make sure the computer is in boot mode and powered off, follow the steps below and refer to Figure 4-22. 1. Disconnect the switc...

4.8 Switch Board 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-35 Installing the Switch Board To install the switch board, make sure that the computer is in boot mode and powered off, follow the steps below and refer to Figure 4-22. 1. Seat the switch board . 2. Se...

4 Replacement Procedures 4.9 Speakers 4-36 Satellite Pro M10 Series Maintenance Manual (960-431) 4.9 Speakers Removing the Speakers To remove the speakers, follow the steps below and refer to Figures 4-23 and 4-24. 1. Turn the computer upside down. 2. Remove two M2.5 × 16 black screws . M2.5 × 16 bl...

4.9 Speakers 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-37 3. Remove one M2.5 × 4 black flat-head screw securing each speaker . 4. Disconnect two speaker cables from PJ5004 and PJ5005 on the system board . 5. Free two speaker cables from their hooks. 6. Remove o...

4 Replacement Procedures 4.9 Speakers 4-38 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Speakers To install the speakers, follow the steps below and refer to Figures 4-23 and 4-24. 1. Seat each of the speaker and secure it from one latch. 2. Secure each of the speaker with on...

4.10 Palm Rest 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-39 4.10 Palm Rest Removing the Palm Rest To remove the palm rest, follow the steps below and refer to Figures 4-25 and 4-26. 1. Turn the computer upside down. 2. Remove seven M2.5 × 12 black screws . M2.5...

4 Replacement Procedures 4.10 Palm Rest 4-40 Satellite Pro M10 Series Maintenance Manual (960-431) 3. Turn the computer right side up and open the display panel. 4. Disconnect the pad cable from PJ2003 on the system board . 5. Remove two M2.5 × 5 black flat-head screws securing the palm rest . 6. Re...

4.10 Palm Rest 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-41 Installing the Palm Rest To install the palm rest, follow the steps below and refer to Figures 4-25 and 4-26. 1. Insert four tabs of the palm rest into the slits on the top cover to seat the palm rest ...

4 Replacement Procedures 4.11 Touch Pad 4-42 Satellite Pro M10 Series Maintenance Manual (960-431) 4.11 Touch Pad Removing the Touch Pad To remove the touch pad, follow the steps below and refer to Figures 4-27 and 4-28. 1. Remove two M2.5 × 5 black flat-head screws and two M2.5 × 4 screws from the ...

4.11 Touch Pad 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-43 2. Hold the palm rest with both hands and then slightly bend it to release two latches securing each sides of the touch pad cover . Be careful not to bend the palm rest excessively, or it will be broke...

4 Replacement Procedures 4.12 Internal Microphone 4-44 Satellite Pro M10 Series Maintenance Manual (960-431) 4.12 Internal Microphone Removing the Internal Microphone To remove the internal microphone, follow the steps below and refer to Figure 4-29. 1. Remove one strip of tape securing the internal...

4.13 Bluetooth Module 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-45 4.13 Bluetooth Module Removing the Bluetooth Module To remove the Bluetooth module, follow the steps below and refer to Figure 4-30. NOTE: The Bluetooth module is an option in some models. 1. Di...

4 Replacement Procedures 4.13 Bluetooth Module 4-46 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Bluetooth Module To install the Bluetooth module, make sure that the computer is in boot mode and powered off, follow the steps below and refer to Figure 4-30. NOTE: The Bluetooth...

4.14 Wireless LAN Mini PCI Card 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-47 4 s 4.14 Wireless LAN Mini PCI Card Removing the Wireless LAN Mini PCI Card To remove the wireless LAN Mini PCI card, make sure the computer is in boot mode and powered off, follow the...

4 Replacement Procedures 4.14 Wireless LAN Mini PCI Card 4-48 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Wireless LAN Mini PCI Card To install the wireless LAN Mini PCI card, follow the steps below and refer to Figure 4-31. 1. Fit the wireless LAN Mini PCI card ’s connector...

4.15 Top Cover with Display Assembly 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-49 4.15 Top Cover with Display Assembly Removing the Top Cover with Display Assembly To remove the top cover with display assembly, follow the steps below and refer to Figures 4-32 t...

4 Replacement Procedures 4.15 Top Cover with Display Assembly 4-50 Satellite Pro M10 Series Maintenance Manual (960-431) 4. Turn the computer right side up and open the display panel. 5. Disconnect following two cables : • LCD/FL cable from PJ4205 on the VGA board • Internal microphone cable from PJ...

4.15 Top Cover with Display Assembly 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-51 6. Remove following screws from the top cover: • Three M2.5 × 5 black screws • One M2.5 × 4 brass flat-head screw • One M2.5 × 12 black flat-head screw M2.5 × 5 black screws M2.5 ...

4 Replacement Procedures 4.15 Top Cover with Display Assembly 4-52 Satellite Pro M10 Series Maintenance Manual (960-431) 7. Lift up the display assembly to release six latches securing the top cover with the bottom case, and then remove the top cover and display assembly . Latches Top cover Display ...

4.15 Top Cover with Display Assembly 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-53 Installing the Top Cover with Display Assembly To install the top cover with display assembly, follow the steps below and refer to Figures 4-32 to 4-35. 1. Seat the top cover with...

4 Replacement Procedures 4.16 Sound Board 4-54 Satellite Pro M10 Series Maintenance Manual (960-431) 4.16 Sound Board Removing the Sound Board To remove the sound board, follow the steps below and refer to Figure 4-36. 1. Remove two M2.5 × 4 screws securing the sound board . 2. Gently lift up the so...

4.17 Cooling Fan 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-55 4.17 Cooling Fan Removing the Cooling Fan To remove the cooling fan, follow the steps below and refer to Figures 4-37. CAUTION: The cooling fan can become very hot during operation. Wait for the fan ...

4 Replacement Procedures 4.17 Cooling Fan 4-56 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Cooling Fan To install the cooling fan, follow the steps below and refer to Figures 4-37. CAUTION: When you remove the cooling fan, wipe the grease off of the bottom of the heat sink a...

4 Replacement Procedures 4.18 RTC Battery 4-58 Satellite Pro M10 Series Maintenance Manual (960-431) Removing the RTC Battery To remove the RTC battery, follow the steps below and refer to Figure 4-38. 1. Remove two strips of tape securing the RTC battery cable . 2. Disconnect the RTC battery cable ...

4.19 System Board 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-59 4.19 System Board Removing the System Board To remove the system board, follow the steps below and refer to Figures 4-39 to 4-41. 1. Lift the AC adaptor jack out of its slot. AC adaptor jack Figure ...

4 Replacement Procedures 4.19 System Board 4-60 Satellite Pro M10 Series Maintenance Manual (960-431) 2. Rotate the system board from the right side to lift it out of the bottom case . Be careful not to catch the bottom case on the eject buttons of the PC Card Slot. 3. Disconnect the AC adaptor jack...

4.19 System Board 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-61 4. Remove two strips of tape securing the modem cable . 5. Disconnect the modem cable from PJ2018 on the system board . PJ2018 Modem cable Tapes Figure 4-41 Removing the modem cable Installing the S...

4 Replacement Procedures 4.20 VGA Board 4-62 Satellite Pro M10 Series Maintenance Manual (960-431) 4.20 VGA Board Removing the VGA Board To remove the VGA board, follow the steps below and refer to Figure 4-42. 1. Remove three M2 × 4 screws securing the VGA board . 2. Gently lift up the VGA board to...

4.21 USB Board 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-63 4.21 USB Board Removing the USB Board To remove the USB board, follow the steps below and refer to Figure 4-43. 1. Remove one M2 × 4 screw securing the USB board . 2. Remove the USB board . M2 × 4 scre...

4 Replacement Procedures 4.22 Display Mask 4-64 Satellite Pro M10 Series Maintenance Manual (960-431) 4 s 4.22 Display Mask Removing the Display Mask To remove the display mask, follow the steps below and refer to Figures 4-44 and 4-45. 1. Remove two mask seals at the bottom corners of the display a...

4.22 Display Mask 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-65 3. Release the twenty-seven latches on the display mask in the following order: • Seven latches on the bottom • six latches each on the right and left sides • eight latches on the top. Latches Displ...

4 Replacement Procedures 4.22 Display Mask 4-66 Satellite Pro M10 Series Maintenance Manual (960-431) Installing the Display Mask To install the display mask, follow the steps below and refer to Figures 4-44 and 4-45. 1. Place the display mask in position, and fasten the twenty-seven latches in the ...

4.23 FL Inverter Board 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-67 4.23 FL Inverter Board Removing the FL Inverter Board To remove the FL inverter board, follow the steps below and refer to Figures 4-46 and 4-47. 1. Remove one M2 × 4 flat-head screw securing t...

4 Replacement Procedures 4.23 FL Inverter Board 4-68 Satellite Pro M10 Series Maintenance Manual (960-431) 3. Rotate out the FL inverter board and disconnect the FL cable from CN1 on the FL inverter board . 4. Disconnect the HV cable from CN2 on the FL inverter board . 5. Remove the FL inverter boar...

4.23 FL Inverter Board 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-69 Installing the FL Inverter Board To install the FL inverter board, follow the steps below and refer to Figures 4-46 and 4-47. 1. Connect the FL inverter cable to CN1 and the HV cable to CN2 . 2...

4 Replacement Procedures 4.24 LCD Module 4-70 Satellite Pro M10 Series Maintenance Manual (960-431) 4.24 LCD Module NOTE: Be careful not to apply pressure to the ICs along the edge of LCD module. The ICs are easily damaged. NOTE: For environmental reasons, do not throw away a malfunctioning LCD modu...

4.24 LCD Module 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-71 3. Carefully rotate out the top of the LCD module to access the LCD/FL cable . 4. Remove the tape securing the LCD/FL cable . 5. Disconnect the LCD/FL cable . 6. Remove the LCD module . Tape LCD cable...

4 Replacement Procedures 4.24 LCD Module 4-72 Satellite Pro M10 Series Maintenance Manual (960-431) 7. Remove four silver super flat-head M2 × 3 screws securing two metal braces . M2 × 3 silver super flat-head screws M2 × 3 silver super flat-head screws Metal brace Figure 4-50 Removing the metal bra...

4.24 LCD Module 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-73 Installing the LCD Module To install the LCD module , follow the steps below and refer to Figures 4-48 to 4-50. 1. Seat two metal braces and secure each with two silver super flat-head M2 × 3 screws ....

4 Replacement Procedures 4.25 Antenna Coaxial Cables 4-74 Satellite Pro M10 Series Maintenance Manual (960-431) 4.25 Antenna Coaxial Cables Removing the Antenna Coaxial Cables To remove the antenna coaxial cables, follow the steps below and refer to Figures 4-51 to 4-53. NOTE: When you open or close...

4.25 Antenna Coaxial Cables 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-75 3. Turn over the insulator securing the antenna coaxial cables . 4. Remove a strip of tape covering the antenna coaxial cables . 5. Free the antenna coaxial cables from their groove . 6. R...

4 Replacement Procedures 4.25 Antenna Coaxial Cables 4-76 Satellite Pro M10 Series Maintenance Manual (960-431) 8. Turn the computer right side up and open the display panel. 9. Pull out the antenna coaxial cables from the hinge . 10. Remove four strips of tape securing the antenna coaxial cables . ...

4.25 Antenna Coaxial Cables 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-77 Installing the Antenna Coaxial Cables To install the antenna coaxial cables, follow the steps below and refer to Figures 4-51 to 4-53. 1. Seat the antennas and route the antenna coaxial ca...

4 Replacement Procedures 4.26 LCD/FL Cable 4-78 Satellite Pro M10 Series Maintenance Manual (960-431) 4.26 LCD/FL Cable Removing the LCD/FL Cable To remove the LCD/FL cable and antenna coaxial cable, follow the steps below and refer to Figures 4-54 to 4-56. NOTE: When you open or close the top cover...

4.26 LCD/FL Cable 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-79 3. Turn the computer right side up and open the display panel. 4. Remove one M2.5 × 6 tapping screw securing the metal brace . 5. Remove the metal brace . Metal brace M2.5 × 6 tapping screw Figure 4...

4 Replacement Procedures 4.26 LCD/FL Cable 4-80 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Close the display panel. 7. Remove the LCD/FL cable . LCD/FL cable Figure 4-56 Removing the LCD/FL cable Installing the LCD/FL Cable To install the LCD/FL cable, follow the steps below and refer ...

4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-81 4 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) Removing the TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) To remove the TFT FL (Model 14.1 XGA Samsung LTN141XF-L0...

4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-83 3. Release the 18 hooks and remove the upper chassis from the frame. There are six hooks at the top, four hooks on each of the left- and right-hand sides, and four ho...

4 Replacement Procedures 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4-84 Satellite Pro M10 Series Maintenance Manual (960-431) 4. Remove the panel assembly from the backlight assembly. CAUTION: Use care not to damage the TCP during working. Panel assembly Backlight assembly Figure 4-60 Removi...

4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-85 5. Remove the two clips. 6. Remove these: • Prism sheet • Diffuser sheet • Light guide plate (LGP) • Reflective sheet Remove the clip Remove the clip Sheets Figure 4-...

4 Replacement Procedures 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4-86 Satellite Pro M10 Series Maintenance Manual (960-431) 7. Remove the two screws for fixing the back cover of the FL tube. Screws Figure 4-62 Removing the screws for fixing the FL tube back cover

4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-87 8. Disconnect the ground wire of the FL tube from the frame. Frame GND wire Hot wire Figure 4-63 Disconnecting the FL tube ground wire

4 Replacement Procedures 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4-88 Satellite Pro M10 Series Maintenance Manual (960-431) 9. Remove the FL tube from the frame. FL Figure 4-64 Removing the FL tube

4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4-90 Satellite Pro M10 Series Maintenance Manual (960-431) 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) Removing the TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) To remove the TFT FL (Model 14.1 XGA LG. Phili...

4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4-92 Satellite Pro M10 Series Maintenance Manual (960-431) Removing the control PCB, top case and cover assembly 6. Remove the FPC cable (1) used for the control PCB connecting. CAUTION : Pressure or stress should not be ...

4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-93 Removing the source PCB and gate PCB 10. Remove the source PCB (1). CAUTION : Pressure or stress should not be given on the PCB and TCP during removing double tap...

4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-95 Board Assembly:6060L-C017 Sheets & LGP Screw Screw Double Tape:7250L-0025E Tape Pad Figure 4-68 Removing the board assembly, tape pad sheet, light guide, cove...

4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-97 Board Assembly:6060L-C017 Sheets and LGP Kapton Tape:7250L-0026Q Screw Screw Double Tape:7250L-0025E Tape Pad Figure 4-69 Attaching the double tape, lamp assembly...

4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4-98 Satellite Pro M10 Series Maintenance Manual (960-431) Attaching the source PCB and gate PCB 9. Attach the source PCB (1). CAUTION : Stress should not be given on the TCP. 10. Attach the gate PCB (2). CAUTION : Stress...

4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-99 Attaching the cover bottom, screw, top case, control PCB and FPC 11. Attach the bottom cover and screw (1). CAUTION : Pressure should not be given on the source T...

4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4-100 Satellite Pro M10 Series Maintenance Manual (960-431) Attaching the outside tape and cover shield 15. Attach the tape adhesive (1) used for B/L wire fixing. CAUTION : Pressure or stress should not be given on the B/...

4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4-102 Satellite Pro M10 Series Maintenance Manual (960-431) 4 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) Removing the TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) CAUTION: Exercise care during FL removal not to damage ...

4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-103 2. Remove two screws securing the PCB. Screw Screw Figure 4-74 Removing the screws securing the PCB 3. Remove four screws on the right and left sides of the chassis....

4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4-104 Satellite Pro M10 Series Maintenance Manual (960-431) 4. Release eight hooks (four hooks on the bottom side first and four hooks on the right and left side) and remove the top chassis from the LCD module starting from t...

4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-105 5. Turn the LCD module face up and remove the panel assembly from the mold-frame . Handle with care not to damage COF. Panel assembly Mold-frame Figure 4-77 Removing...

4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4-106 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Remove two clips and six sheets (protector, prism(L,U), diffuser, LGP, and reflector sheet) from the back light assembly. Clip Clip Sheets Figure 4-78 Removing on...

4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-107 7. Turn the back light assembly face down and remove two screws to remove the lamp cover from the mold frame. Screw Screw Lamp cover Figure 4-79 Removing the lamp co...

4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4-108 Satellite Pro M10 Series Maintenance Manual (960-431) 8. Free the HV cable from the mold-frame’s cable guide. HV cable (GND) HV cable (HOT) Figure 4-80 Freeing the HV cable

4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-109 9. Pull the FL assembly out of its groove on the mold frame. FL assembly Figure 4-81 Removing the FL assembly

4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-119 4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) Removing the TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) To remove the TFT FL (Model 15.0 XGA Chi Mei N150X2-L01), follo...

4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-121 5. Push the latch out of lower frame from the lamp holder and then the latch on both sides. Be careful not to distort the frame. Backlight Metal frame Figure 4-92 Remo...

4 Replacement Procedures 4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4-122 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Unfold the X-PCB. Be careful not to distort the TCP. 7. Turn the LCD module right side up. 8. Remove the panel. Panel Backlight unit Figure 4-93 Removing the panel

4 Replacement Procedures 4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4-124 Satellite Pro M10 Series Maintenance Manual (960-431) 11. Remove two screws securing the FL. 12. Remove the FL. Screw Screw FL Housing Figure 4-95 Removing the FL

4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4-126 Satellite Pro M10 Series Maintenance Manual (960-431) 4 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) Removing the TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) CAUTION: Exercise care during FL removal not to d...

4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-127 2. Remove two screws securing the PCB. Screw Screw Figure 4-97 Removing the screws securing the PCB

4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4-128 Satellite Pro M10 Series Maintenance Manual (960-431) 3. Remove four screws on the right and left sides of the chassis. Screws Screws Figure 4-98 Removing screws securing the chassis

4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-129 4. Release nine hooks (four hooks on the bottom side first and five hooks on the right and left side) and remove the top chassis from the LCD module starting from ...

4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4-130 Satellite Pro M10 Series Maintenance Manual (960-431) 5. Turn the LCD module face up and remove the panel assembly from the mold-frame . Handle with care not to damage COF Panel assembly Mold-frame Figure 4-100 Removi...

4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-131 6. Remove two clips and five sheets (prism(L,U), diffuser, LGP, and reflector sheet) from the back light assembly. Clip Clip Sheets Figure 4-101 Removing one screw...

4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4-132 Satellite Pro M10 Series Maintenance Manual (960-431) 7. Turn the back light assembly face down and remove two screws to remove the lamp cover from the mold frame. Screw Screw Lamp cover Figure 4-102 Removing the lamp...

4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-133 8. Free the HV cable from the mold-frame’s cable guide. HV cable (GND) HV cable (HOT) Figure 4-103 Freeing the HV cable

4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4-134 Satellite Pro M10 Series Maintenance Manual (960-431) 9. Pull the FL assembly out of its groove on the mold frame. FL assembly Figure 4-104 Removing the FL assembly

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-136 Satellite Pro M10 Series Maintenance Manual (960-431) 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) Removing the TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) To remove the TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43), f...

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-137 3. Remove four screws from the side of the LCD module. Screw Screw Screw Loosen the screws with 1.1kgf ⋅ cm of torque. Screw Figure 4-106 Removing the screws 4. Turn ...

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-139 10. Turn the LCD module right side up. 11. Remove the LCD panel from the backlight unit. When you remove the LCD panel, wear finger covers or gloves to avoid contamin...

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-140 Satellite Pro M10 Series Maintenance Manual (960-431) 12. Turn the backlight unit upside down taking care not to damage or contaminate the sheets. 13. Remove two screws securing the lamp cover to remove it. Screw Screw L...

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-141 14. Turn the backlight unit right side up. 15. Remove the upper diffuser sheet, lens sheet, and light guide sheet. Be careful not to damage or contaminate the sheets ...

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-142 Satellite Pro M10 Series Maintenance Manual (960-431) 17. Turn the backlight unit upside down. 18. Gentry remove the FL taking care not to damage it. P-chassis FL Figure 4-113 Removing the FL NOTE : Be careful not to fol...

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-144 Satellite Pro M10 Series Maintenance Manual (960-431) 2. Install a new FL unit into the frame. Frame FL Cross section of Z—Z Install the FL into the frame making sure it does not stick out from the frame. Let the reflect...

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-145 3. Seat the lamp cover on the backlight unit and secure it with two screws. Tighten the screws with 0.9kgf•cm of torque. Screw Screw Lamp cover Figure 4-116 Installin...

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-146 Satellite Pro M10 Series Maintenance Manual (960-431) 5. Strip all of the liner on the double-faced tape applied to the frame. 6. Lay the lens sheet and upper diffuser sheet on the backlight unit. Be careful not to conta...

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-147 7. Seat the LCD panel on the backlight unit assembled by the steps above. Make sure there are no dust between the LCD panel and the backlight. If you find any foreign...

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-148 Satellite Pro M10 Series Maintenance Manual (960-431) 9. Fold the TCP of the source PCB down. 10. Secure the source PCB with two screws. 11. Fold the TCP of the gate PCB down. 12. Secure the gate PCB with two screws. Do ...

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-150 Satellite Pro M10 Series Maintenance Manual (960-431) 14. Install the top frame. Secure the top frame and the lamp cover with six latches. <Side view> Top frame Hook the U-shaped side of the top frame to the P-chas...

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-151 15. Secure four screws on the side of the module. Screw Screw Screw Tighten the screws with 0.9kgf ⋅ cm of torque. Screw Figure 4-123 Securing the screws 16. Apply th...

4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4-152 Satellite Pro M10 Series Maintenance Manual (960-431) 17. Apply the protective cover-S. Align the cover's edge with the edge of the plastic part of the connectorMake sure that the amount of displacement is ± 0.5 mm or le...

4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-153 18. Apply the fixing tape and the HV cable fixing tape. Secure the cable with tape.Be sure the cable lies flat. Apply the fixing tape around the center of the module....

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-154 Satellite Pro M10 Series Maintenance Manual (960-431) 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) CAUTION : When you replace the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LC...

4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-155 3. Remove five screws from the side of the LCD module. Loosen the screws with 1.0 kgf•com of torque. Screw Screw Screw Screw Screw Figure 4-128 Removing the screws 4. ...

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-156 Satellite Pro M10 Series Maintenance Manual (960-431) 6. Turn the LCD module upside down. 7. Remove five screws securing the PCBs. 8. Disconnect the FPC . FPC Open the connector cover and disconnect the connector. Loosen ...

4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-159 Installing the TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) To install the TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13), follow the steps below and refer to Figures 4-136 ...

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-160 Satellite Pro M10 Series Maintenance Manual (960-431) 2. Seat the lamp cover on the backlight unit and secure it with two screws . V W Lamp cover Tighten the screws with 1.0kgf•cm of torque. Detail of W Detail of V Backli...

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-162 Satellite Pro M10 Series Maintenance Manual (960-431) 5. Seat the LCD panel on the backlight unit assembled by the steps above. Make sure there is no dust between the LCD panel and the backlight unit . If you find any for...

4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-163 7. Secure the TCP of the source PCB with three screws . 8. Secure the TCP of the gate PCB with two screws . 9. Connect the FPC to the connector on the source PCB. Scre...

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-164 Satellite Pro M10 Series Maintenance Manual (960-431) 10. Install the top frame . Top frame Hook the U-shaped side of the top frame to the P-chassis. <Side view> Lay the top frame on the lamp cover. Be sure the top ...

4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures Satellite Pro M10 Series Maintenance Manual (960-431) 4-165 12. Secure five M2 × 2 screws on the side of the module. Screw Screw Screw Screw Screw Tighten the screws with 1.0 kgf•cm of torque. Figure 4-145 Securing the screws 1...

4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4-166 Satellite Pro M10 Series Maintenance Manual (960-431) 14. Apply the protective cover-S , the aluminum tape and the wire-protective tape . 0 ‘ 0.5m m 0 ‘ 1mm 0 ‘ 1mm 0 ‘ 1mm Protective cover-S Aluminum sheet Aluminum tape ...

Appendices Satellite Pro M10 Series Maintenance Manual (960-431) App-iii Appendix Contents Appendix A Handling the LCD Module .......................................................................... A-1 Appendix B Board Layout ..........................................................................

Appendix A Handling the LCD Module Satellite Pro M10 Series Maintenance Manual (960-431) A-1 Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the ...

Appendix B Board Layout Appendices Satellite Pro M10 Series Maintenance Manual (960-431) B-1 Appendix B Board Layout B.1 System Board (FQDSY*) Front View Figure B-1 System board (FQDSY*) layout (front)

Appendices Appendix B Board Layout B-2 Satellite Pro M10 Series Maintenance Manual (960-431) Table B-1 System board (FQDSY*) layout (front) (1/2) Mark Number Name (A) PJ123 Keyboard I/F Connector (B) PJ326 Debug Port I/F Connector (C) PJ2003 Touch Pad I/F Connector (D) PJ2015 Mini PCI Card I/F Conne...

Appendices Appendix B Board Layout B-6 Satellite Pro M10 Series Maintenance Manual (960-431) Table B-2 System board (FQDSY*) layout (back) (2/2) Mark Number Name (AA) F8810 Fuse for Battery (10A) (AB) F8820 Fuse for Slim Select Bay (10A) (AC) S2302 Wireless Communication Switch (AD) X2002 Clock for ...

Appendix B Board Layout Appendices Satellite Pro M10 Series Maintenance Manual (960-431) B-9 B.5 Sound Board (FQDSD*) Front View Figure B-5 Sound board (FQDSD*) layout (front) Table B-5 Sound board (FQDSD*) layout (front) Mark Number Name (A) PJ5002 Internal Microphone I/F Connector

Appendices Appendix B Board Layout B-10 Satellite Pro M10 Series Maintenance Manual (960-431) B.6 Sound Board (FQDSD*) Back View Figure B-6 Sound board (FQDSD*) layout (back) Table B-6 Sound board (FQDSD*) layout (back) Mark Number Name (A) PJ5000 External Microphone I/F Connector (B) PJ5003 Headpho...

Appendix B Board Layout Appendices Satellite Pro M10 Series Maintenance Manual (960-431) B-11 B.7 USB Board (FQDUB*) Back View Figure B-7 USB board (FQDUB*) layout (back) Table B-7 USB board (FQDUB*) layout (back) Mark Number Name (A) PJ2033 USB I/F Connector (B) PJ2042 System Board (FQDSY*) I/F Con...

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Maintenance Manual (960-431) C-1 Appendix C Appendix C Pin Assignments System Board (FQDSY*) C.1 PJ100 VGA Board (FQDVG*) I/F Connector (200-pin) Table C-1 VGA board (FQDVG*) I/F connector pin assignments (200-pin) (1/3) Pin No. Signal name I...

Appendices Apx.C Pin Assignments C-4 Satellite Pro M10 Series Maintenance Manual (960-431) C.2 PJ117 Slim Select Bay I/F Connector (72-pin) Table C-2 Slim Select Bay I/F connector pin assignments (72-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 GND - 2 GND - 3 CDAUDR-EXP O 4 CDAUDL-EXP O 5...

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Maintenance Manual (960-431) C-5 C.3 PJ123 Keyboard I/F Connector (34-pin) Table C-3 Keyboard I/F connector pin assignments (34-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 NUMLED-P5N I 2 ARWLED-P5N I 3 CAPLED-P5N I 4 P5V O 5 KBSC00...

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Maintenance Manual (960-431) C-15 C.11 PJ2003 Touch Pad I/F Connector (8-pin) Table C-11 Touch Pad I/F connector pin assignments (8-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 P5V O 2 IPDDAT-P5P 3 IPDCLK-P5P 4 GND - 5 SP-GND 6 SPY-...

Appendices Apx.C Pin Assignments C-18 Satellite Pro M10 Series Maintenance Manual (960-431) Table C-12 Docking I/F connector pin assignments (242-pin) (4/4) Pin No. Signal name I/O Pin No. Signal name I/O 201 RTS-PYP O 202 CTS-PYP I 203 DTR-PYP O 204 SELCT-P5P I 205 BUSY-P5P I 206 ACK-P5N I 207 PDB0...

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Maintenance Manual (960-431) C-23 C.18 PJ2040 USB Board (FQDUB*) I/F Connector (30-pin) Table C-18 USB Board (FQDUB*) I/F connector pin assignments (30-pin) Pin No. Signal name I/O Pin No Signal Name I/O 1 E5V O 2 E5V O 3 E5V O 4 E5V O 5 E5V ...

Apx.C Pin Assignments Appendices Satellite Pro M10 Series Maintenance Manual (960-431) C-27 C.27 PJ8810 Battery I/F Connector (10-pin) Table C-27 Battery I/F connector pin assignments (10-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 + 2 BTMP1 3 DCHG 4 M5V 5 PSCL-S5P 6 PSDA-S5P 7 GND - 8 DB...

Appendix D Keyboard Scan/Character Codes Satellite Pro M10 Series Maintenance Manual (960-431) D-1 Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0...

Appendix D Keyboard Scan/Character Codes D-4 Satellite Pro M10 Series Maintenance Manual (960-431) Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 ...

Appendix D Keyboard Scan/Character Codes Satellite Pro M10 Series Maintenance Manual (960-431) D-5 Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E...

Appendix D Keyboard Scan/Character Codes D-6 Satellite Pro M10 Series Maintenance Manual (960-431) Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 ...

Appendix D Keyboard Scan/Character Codes D-8 Satellite Pro M10 Series Maintenance Manual (960-431) Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Common * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make co...

Appendix E Key Layout Satellite Pro M10 Series Maintenance Manual (960-431) E-1 Appendix E Appendix E Key Layout E.1 United States (US) Keyboard Figure E-1 US keyboard E.2 United Kingdom (UK) Keyboard Figure E-2 UK keyboard

Appendix F Wiring Diagrams Satellite Pro M10 Series Maintenance Manual (960-431) F-1 Appendix F Appendix F Wiring Diagrams F.1 Parallel Port Wraparound Connector Figure F-1 Parallel port wraparound connector F.2 Serial Port Wraparound Connector Figure F-2 Serial port wraparound connector

Appendix G BIOS Rewrite Procedures Satellite Pro M10 Series Maintenance Manual (960-431) G-1 Appendix G Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool: BIOS/EC/KB...

Appendix H EC/KBC Rewrite Procedures Satellite Pro M10 Series Maintenance Manual (960-431) H-1 Appendix H Appendix H EC/KBC Rewrite Procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system. Tools To rewrite the EC/KBC, you need the following tool: ...

Appendix I Reliability Satellite Pro M10 Series Maintenance Manual (960-431) I-1 Appendix I Appendix I Reliability The following table shows MTBF (Mean Time Between Failures) for each component. Table I-1 MTBF Component Time (hours) LCD 50,000 Keyboard 40,000 HDD 300,030 FDD 43,800 CD-RW/DVD drive 5...