Toshiba IK-TF2- Manuals

- 8 - ① Prism faceplate ⑨ RGB terminal ② DISP button ③ PAGE button ④ MENU UP button ⑤ MENU DOWN button ⑥ DATA UP(AWB) button ⑦ DATA DOWN button ⑧ DC IN 12V terminal DISP PAGE DC IN 12V RGB MENU DATA (AWB) ［ Front ］ ［ Rear ］ Prism faceplate The protection cap is attached on the lens mount portion. Af...

- 9 - Lens IK-TF2 monitor DC IN 12V DC power supply Less than 4mm RGB Camera cable (option) When connecting the camera cables, be sure to turn off the camera and the other equipment connected. We suggest using a C mount lens made for a 3CCD camera. When using another lens, the best camera performanc...

- 10 - Referring to the item “ 5. CONNECTION”, connect each equipment correctly. Turn on the connected equipment and the camera. Pointing the lens at the object, operate the lens iris adjustment, focus adjustment, etc.. Referring to the item “6.1 White Balance”, operate the adjustment. Referring to ...

- 12 - When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level. For the gain adjustment of the unit, MANUAL (Manual) and OFF (0 dB) modes are provided. Select the mode on the GAIN menu. (Refer to the item “7.2 (2) GAIN (Video gain)”.) MANUAL(M...

- 13 - Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The contents once set are memorized when the power is turned off, so it is unnecessary to set again when using the unit next time. When the setting is performed, select the menu of the item to...

- 14 - Select the menu to change the setting by referring the item “7.1 Using the Menus”.) When the [MENU UP], [MENU DOWN] buttons are pushed, the “ ” on the screen moves up and down. Move the “ ” to the item to change. ( 1 ) SHUTTER Electronic shutter The electronic shutter has three modes; MANUAL,...

- 18 - 1 3 3 Changing each setting in 2PULSE mode Shutter mode MANUAL, SS, EXT TRIG -- 1 SHUTTER -- EXT TRIG mode MODE EXT TRIG 1PULSE SNR, 1PULSE SR, 2PULSE EXT TRIG 2PULSE TRIG PULSE Input trigger pulse setting at 2PULSE FLD FRM FLD The rising edge The falling edge F ront and back edges of pulse F...

- 19 - 2 GAIN (Video gain) GAIN has two modes; MANUAL, OFF. Set the “ ” to MODE, push the [DATA UP], [DATA DOWN], and select mode among MANUAL, OFF. In the OFF mode, gain is fixed to 0dB. 2 1 Changing each setting in GAIN -- 2 GAIN -- Gain mode MANUAL, OFF MODE MANUAL MANUAL 0dB Manual gain setting ...

- 21 - 4 PROCESS Master pedestal adjustment -64 to 64 R pedestal adjustment -64 to 64 -- 4 PROCESS -- B pedestal adjustment -64 to 64 M.PED 0 R.PED 0 White clip adjustment -50 to 50 B.PED 0 WHT CLIP 0 Shading mode setting MANUAL / OFF SHADING MANUAL MANUAL 0 Manual shading adjustment -100 to 100 Mov...

- 22 - 5 SYNC When an external sync signal is input, the display changes from INT (internal sync) to EXT (external sync) automatically. Sync system display -- 5 SYNC -- H PHASE -100 to 100 MODE EXT H PHASE 0 RGB SYNC G, ALL ON, ALL OFF RGB SYNC G Move up and down By pushing MENU UP,DOW N Set by push...

- 24 - 4 Changing HD/VD input/output (1) Put off 6 screws both on flank/top of camera chassis. (2) Change internal switch SJ01(HD/VD). SJ01 HD/VD OUTPUT HD/VD INPUT high-impedance HD/VD INPUT 75 Ω (factory setting) The shutter speed can be set by the horizontal scanning period (1H) or by the frame. ...

- 25 - Charge begins to accumulate after the trigger input, and 1 field or 1 frame images are output. There are three modes: 1PULSE SNR, 1PULSE SR and 2PULSE. The RGB terminal trigger input and index output interface are as shown below. Trigger input INDEX out CMOS out 1 1 PULSE SNR 1 Pulse Sync Non...

- 27 - 2 1 PULSE SR 1 Pulse Sync Reset Charge begins to accumulate after the trigger input to the RGB terminal, the vertical sync signal is reset and field images are output. (a) Rising edge / Falling edge mode The exposure time is set to 0.02 ms to 16 ms on the menu. Trigger pulse level (Low Level)...

- 28 - 3 2PULSE Accumulation of charges is started and ended through the trigger pulse input to the RGB terminal, the vertical sync signal is reset and field images are output. Trigger pulse level (Low Level) Less than 0.5V , (High Level) 3.4V to 5V RGB terminal Trigger pulse fetch timing Rising edg...

- 30 - Symptom Items to be checked No image Is the power supplied correctly? Is the lens iris adjusted correctly? Are the cables connected correctly? Is the shutter mode set correctly? Poor color Is the monitor (TV) adjusted correctly? Is the white balance of the camera adjusted correctly? Is the il...

- 31 - Unit : mm [inch] 44 [1.73] 44 [1.73] 22 [0.87] 5 [0.20] 26 [1.02] 2-M3 Depth 3 6.3 [0.25] 7 8 [ 3 . 0 7 ] 5 [0.20] 56 [2.20] 5 [0.20] 26 [1.02] 25 [0.98] 25 [0.98] 25 [0.98] 12 [0.47] 34 [1.34] 10.7 [0.42] No.4-40UNC 4-M2 Depth 3 26 [1.02] 4-M3 Depth 3 DISP PAGE DC IN 12V RGB MENU DATA (AWB) ...