Toshiba EO1-11099- Manuals

– 2 – EO1-11113 TABLE OF CONTENTS 1. TO OUR CUSTOMERS ................................................................................................................... 1 2. UNPACKING ......................................................................................................................

- 1 - EO1-11113 1. TO OUR CUSTOMERS Thank you for choosing the TEC electronic cash register FS-1650 series. This instruction manualprovides a description of the functions and handling of this register and should be read carefully toensure optimum performance. Since every consideration has been given...

- 3 - EO1-11113 3. APPEARANCE AND NOMENCLATURE Customer Display Operator Display Keyboard Drawer Receipt Outlet Journal Window Mode Lock Power Switch • Power Switch ........ The power switch is provided at the right-hand side of the cabinet. The AC power is turned on when the switch is pushed to ON,...

- 4 - EO1-11113 SET ........... In this position, the register will allow pro- gramming operations .................. (LOCK position) The register operations are locked when the Mode Lock is in this posi-tion. Meanwhile, the Display Message andthe current time are displayed. REG .......... Normal ca...

- 5 - EO1-11113 WG WH BETRAG TL ZWS ZUR BON AUS ALM BED EIN IN-LINE BEL The customer display can be fixed as a rear display or moved to form a remote display. It can be movedup, down, to the right, and to the left, and thus is fully adjustable according to the position of the customer. CUSTOMER DISP...

- 7 - EO1-11113 (3) Error Messages (in any mode except "LOCK") When an error occurs, an error message (programmable) is displayed, with an error buzzer gener-ated (a long tone). Read the Error Message, depress the [C] key to cancel the error status and tone, operate thesequence again after r...

- 9 - EO1-11113 6. OUTLINE OF PREPARATION PROCEDURE BE- FORE OPERATING THE ECR This chapter shows the outline of set-up procedure of the ECR before actually starting the ECRoperation. 4 3 2 1 5 (1) (4) (5) (6) (8) (2) (3) (7) WARNING! Turn the POWER SWITCH to OFF before connecting the power cord. Re...

- 10 - EO1-11113 6 Install the Receipt and Journal rolls (referring to the following section "Installing the Receipt/Journal Roll"). Installing the Receipt/Journal Roll WARNING! Care must be taken not to injure yourself with the paper cutter. Installing the Receipt Roll 1 2 3 4 REG X SET Z M...

- 12 - EO1-11113 There are the following two ways of a journal paper feed procedure. A: Manual installationB: Installation using the [JF] key A: Manual installation Lift the green lever on the journal side. Insert paper from the rear of the printer untilthe leading edge of paper comes out by 30cm. I...

- 13 - EO1-11113 1 Setting the Ribbon Cassette Detach the Ribbon Cover. Set the Ribbon Cassette.After setting the Ribbon Cassette, turn the knobof the Ribbon Cassette in the arrow directionseveral times to remove the slack on the ribbon. 3 4 Attach the Ribbon Cover.

- 14 - EO1-11113 Sign-OUT Sign-IN [LOG/RECEIPT] [LOG/RECEIPT] 9 [LOG/RECEIPT] 0 [LOG/RECEIPT] Anmeldung Anmeldung 0 [LOG/RECEIPT] [LOG/RECEIPT] [LOG/RECEIPT] A sign-on receipt is issued, and salesentries are now possible. 2-digit manager-assign code (01 to 99) 2-digit cashier's own secret code(01 to...

- 15 - EO1-11113 Sign-ON [X] [LOG/RECEIPT] NOTES: 1. Sign-OFF or Sign-OUT may automatically be performed without operating each key operation on finalizing each transaction including Check (or other non-cash media)Cashing, No-sale Exchange from/to Foreign Currencies, No-sale, Received-on-Account,Pai...

- 16 - EO1-11113 (3) Mode Changes With Signing Operations When Signed-ON or Signed-IN: The Mode Lock position changes are allowed within "LOCK", "REG", "MGR", and " ". Changing to any other position will be an error. When Signed-OUT: The Mode Lock may be turned to any...

– 17 – EO1-11113 Each key is assigned to each cashier. The register will not operate in the "REG", "MGR", or " " mode unless one of these keys is inserted and pushed on or pushed-and-locked at the corresponding CashierLock. The light is lit when the key is in the ON-status. E...

– 19 – EO1-11113 7.4. TRAINING MODE START AND END When you have newly employed cashiers, you may provide some time for them to train their skills ofoperating the FS-1650. You are to start and end the Training Mode. Once entering the Training Mode, acashier may operate just as ordinary sale entry ope...

– 21 – EO1-11113 8. KEYBOARD LAYOUT The following is typical keyboard layouts for the FS-1650 series. Since this series is designed to be capableof programming most of the keys to be placed in the desired place on the keyboard, this is merely example.The keyboard of your register should have its own...

- 22 - EO1-11113 FUNCTIONS LOG key. Used in case of Cashier Code Entry method, todeclare start or end of normal operation by cashier. Fordetails, refer to Section 7.1. Receipt key. Used to change the receipt-ON/OFF mode. Log/Receipt key. This is a dual-function key that has both[LOG] and [RECEIPT] f...

- 23 - EO1-11113 FUNCTIONS Non-add Number Print key. Used to print a non-addnumber (such as Customer No., Credit Card No., etc.) onthe receipt and journal for future reference. No-sale key. Used to open the cash drawer without relatinga sale, and also used to display the store message. Amount key. U...

- 25 - EO1-11113 FUNCTIONS Media-coupon, Credit 1 to Credit 4 keys. These areadditional non-cash media keys that may be installedbesides those already described, according to the require-ments of each store. Card No. key. Used to enter the code number (1 to 12)which classifies the credit card compan...

- 26 - EO1-11113 FUNCTIONS Salesperson key. Used to record sales contribution dataof each salesperson for report purpose. Repeat key. Used to repeat a department or PLU itementry. Foreign Currency keys. Used in tendering or exchangewith foreign currencies. Scale key. This key is used for various sca...

- 28 - EO1-11113 TRAINING MODE is available: If you are a beginner in operating this register, ask the store manager for practicing in the TRAIN-ING MODE. During your operations, the following may occur: • Errors ... A tone continuously sounds and an error message appears in the upper row of the Ope...

- 29 - EO1-11113 Cashier Sign-ON or Cashier Key to ON status: If the [LOG/RECEIPT] (or [LOG]) key is installed, you must sign-ON or sign-IN. (SeeSection 7.1.) If Cashier Keys or Cashier Locks are installed, you must set your cashier key to the ONstatus. (See Section 7.2. and 7.3.) Now you are ready ...

- 30 - EO1-11113 NOTES: 1. The “R OFF” lamp status at the starting of a transaction entry decides whether a receipt will be issued for the transaction or not. Switching the Receipt ON/OFF status duringa transaction will not be effective. 2. If a transaction entered with the “R OFF” lamp illuminated ...

- 31 - EO1-11113 LOAN This operation is used to record the cash amounts and food stamps loaned from the store as the changereserve in the drawer. (must be operated outside a sale) [R/A] | Cash Amount Loaned | [AT/TL] ([ST]) [AT/TL] | Food Stamp Amount Loaned | [FSTL TEND] NO-SALE The no-sale transac...

- 33 - EO1-11113 OPERATION MODIFIER PLU ENTRY Some PLUs can be programmed as “MODIFIER” descriptors (such as “PEPPER”, “RARE”, “MEDIUM” forgrilling a steak item, and toppings for dishes, etc.) • When entering a Modifier PLU onlySame operations as PLU Entry • When entering a Modifier PLU after a PLU ...

– 35 – EO1-11113 SPLIT PACKAGE PRICING ("Q'ty" = Quantity... in the patterns listed below) (1) Department Open Department • | Purchased Q'ty | [@/FOR] | Whole Package Q'ty | [@/FOR] | Whole Package Price | [Open Dept] | Open-Dept Code | [DP#] | Whole Package Price | [AMT] Preset Department •...

– 36 – EO1-11113 (2) PLU Open PLU • | Purchased Q'ty | [@/FOR] | Split-Price Type PLU Code | [PLU] | Whole Package Price | [PLU Preset-code Key] Preset PLU • | Purchased Q'ty | [@/FOR] | Split-Price Type PLU Code | [PLU] [PLU Preset-code Key] Preset-Price Open • [PR OPEN] (or [OPEN]) | Purchased Q't...

– 37 – EO1-11113 PLU PRICE SHIFT ENTRY This operation is to register the PLU code which is added 1, 2, or 3 to the code of the entered PLU. • [PRICE SHIFT 1] [PLU] (PLU code plus 1) • [PRICE SHIFT 2] [PLU] (PLU code plus 2) • [PRICE SHIFT 3] [PLU] (PLU code plus 3) • [PR OPEN] [PRICE SHIFT 1 ~ 3] | ...

– 38 – EO1-11113 SINGLE-ITEM DEPARTMENT or SINGLE-ITEM PLU ENTRY If a department (or PLU) is programmed as Single-item, the department (or PLU) entry sequence willimmediately finalizes the sale as cash sale when operated outside a sale. Same as DEPARTMENT ENTRYPLU ENTRYQUANTITY EXTENSIONSPLIT PACKAG...

– 39 – EO1-11113 OPERATION -- Guest Check -- P B + $0.00 Hamb. Steak $7.50TVeget. Salad $2.20TCoffee $2.50TTAX1 $0.73TAX2 $0.13CASH $ 1 3 . 0 6 ITEM 3JONES 0021 13:48TM -- Receipt Print Format -- ORDER ENTRY, PREVIOUS BALANCE ENTRY [PB] (for a new order entry) menu item entries Sale Finalization by ...

– 40 – EO1-11113 ADDITIONAL ORDER ENTRY | Number of Lines to be fed | [GCP LINE#] | Previous Balance | [PB] menu item entries, if any Sale Finalization [TOTAL] ...to transfer all the balance NOTES: 1. Previous Balance Entry can be executed even when a slip has not been inserted into the Guest Check ...

– 42 – EO1-11113 Charge Posting Operation Sample 0. 0 0 0 1 1. 2 0 0 3 3. 5 0 4. 9 8 4. 9 8 4. 9 8 4. 9 8 4. 9 8 5. 0 2 Mr. JAMES HAILY comesand you start chargeposting for him. Menu Items: $1.20 Dept. 1$3.50 Dept. 3 Finalize this sale. To transfer all the balancewithout payment. Mr. JAMES HAILY now...

– 43 – EO1-11113 RETURNED MERCHANDISE DEPARTMENT ENTRYPLU ENTRYQUANTITY EXTENSIONSPLIT PACKAGE PRICINGSET MENU ENTRYSINGLE-ITEM DEPARTMENT/PLU ENTRY OPERATION -- Receipt Print Format -- RTNBAKERY -1.45TFRTNCAN FOOD -0.45TF --- BOTTLE RETURN | Bottle Return Amount | [BTL RTN] | Quantity | [@/FOR] | U...

– 44 – EO1-11113 DOLLAR DISCOUNT NOTES: 1. The discount amount must not exceed the item amount or the subtotal unless the “Credit Balance” option is selected. 2. A discount entry causes an error if operated during the compulsory status of modifier PLU entry or operated to modifier PLU item itself. P...

– 45 – EO1-11113 STORE COUPON [STR CPN] Follow DEPARTMENT ENTRYQUANTITY EXTENSION for DEPTs OPERATION S. CPNCAN FOOD -0.50TF -- Receipt Print Format -- NOTE: The store coupon amount to be entered must not exceedthe sale total unless the “Credit Balance” option is selected. VENDOR COUPON ([ST]) | Cou...

– 46 – EO1-11113 VOID The VOID operation is used to delete an item already entered before the last item within the currentsale. Such items cannot be deleted by the [ITEM CORR] key any longer. [VOID] DEPARTMENT ENTRYPLU ENTRYQUANTITY EXTENSIONSPLIT PACKAGE PRICINGSET MENU ENTRY NOTE: An amount exceed...

– 47 – EO1-11113 NUMBER-OF-GUESTS ENTRY This operation is used to enter the number of guests of the sale. NOTES: 1. The Number-of-Guests entry is allowed at the start of or any time during a sale if before the sale finalization by media keys. 2. When the operation is made more than once in a sale, t...

– 48 – EO1-11113 (2) Auto Scale With Tare (3) Manual Scale Entry (It may be prohibited by a program option.) (4) Return or Void Manual Scale Entry (It may be prohibited by a program option.) [RTN MDSE] for Return [VOID] for Void LISTING CAPACITY OPEN For Department and PLUs Depress [LC OPEN] (or [OP...

– 49 – EO1-11113 MANUAL TAX ENTRY (where irregular tax amount addition is applied) | Irregular Tax Amount to be Added | [TAX] SUBTOTAL (Sale Total Pre-taxed) READ [ST] The sale total (pre-taxed) of the items so far entered is displayed (and printed if soprogrammed), but the sale is not finalized. Ad...

– 51 – EO1-11113 FOOD STAMPABLE TOTAL READ, FOOD STAMP TENDERING [FSTL TEND] | Food Stamp Tendered Amount | [FSTL TEND] ... When the Food Stamp tendered amount is less than the sale total, the sale is not finalized with the balance still due displayed. Then it can be finalized with cash or othermedi...

– 52 – EO1-11113 4. When a media is programmed to allow "Total" function, it can also be programmed with the "Drawer Open" or "Not Open" status on operating the key. MULTI-TENDERING Short-tendering repeated multiple times by the same media (allowed only when the media key isp...

– 53 – EO1-11113 NOTES: 1. In both MULTI-TENDERING and SPLIT TENDERING operations, the sale is finalized and a receipt is issuedon reaching the sale total amount. 2. If a media key is depressed without an amount tender entry and the key is programmed to function as "Total"key, the sale is th...

– 54 – EO1-11113 5. When a tendering by a foreign currency occurs during a short-tendered condition, the [TXBL TL] key will not be mandatory. 6. A sale of negative balance cannot be finalized using any of the foreign currency keys. NO-SALE EXCHANGE from Foreign Currency to Domestic Currency (must be...

– 56 – EO1-11113 SALESPERSON ENTRY (Salesperson Sign-ON) | Salesperson Code | [SALES PERSON] 1 to 99 Programmable options relating to Salesperson Entries: • Salesperson's name non-print on receipt (print on journal only) • Salesperson Entry compulsory before sale item entries • Salesperson Entry Pro...

– 58 – EO1-11113 This line is printed only when a post-issue receipt is issued after theOrdinary Receipt is issued, or thesecond and subsequent post-issuereceipts are issued. 19-12-1994 MON #3001 * C O P Y * VEGETABLE $1.00TFCheese $2.50TF%- 5% -0.13TTAX $0.06TOTAL $ 3 . 5 8 CATEND $5.00CHANGE $1.42...

– 59 – EO1-11113 TRAY TOTAL Menu item Entries [TRAY TOTAL] Sale Finalization by Media Keys [TOTAL] ... to transfer all the balance EAT-IN/TAKEOUT ENTRY ( ) [EAT IN] (Eat-in entry) ( ) [TAKEOUT] (Takeout entry) NOTES: 1. Depressing the [EAT IN] or [TAKEOUT] key is allowed any number of times during o...

– 62 – EO1-11113 ENDORSEMENT PRINT NOTES: 1. Endorsement Message can be printed on the Receipt/Journal Printer with Multi- validation Function. 2. The Check No. entry prior to the [CHECK NO.] key may be programmed to be compulsory. OPERATION After operating the requirednon-cash media key (usuallythe...

– 63 – EO1-11113 GUEST CHECK PRINTER (hardware option) OPERATION The TEC Guest Check Printer DRS-207 may be connected to the FS-1650 series ECR as an optionaldevice. The Guest Check Printer will operate printing if a slip is properly inserted, regardless of the ModeLock position (except that no prin...

– 64 – EO1-11113 WHEN A POWER FAILURE OCCURS ... If a power failure occurs, all sales data stored in the memory are automatically protected by the batteryinstalled in the ECR. The battery is rechargeable and it is recharged when the AC power returns. As thepower returns, the register revives to cont...

- 65 - EO1-11113 11. JOURNAL AND RECEIPT PAPER-END DETECTOR (1) This detects when either the journal or receipt paper is coming near the end. It is provided in orderto prompt the operator to replace the old paper roll with a new one. (2) When the paper roll comes near the end (or the paper has not b...

- 66 - EO1-11113 Load new paper roll as described in Chapter 6. 15. PAPER ROLL REPLACEMENT AND OTHER MAIN- TENANCE OPERATIONS WARNING! Care must be taken not to injure yourself with the paper cutter. Replacing the Receipt Roll 1 2 3 4 RF To remove the Receipt Cover, insert the ReceiptCover Key to th...

- 67 - EO1-11113 3 1 2 4 JF Replacing the Journal Roll To remove the Receipt Cover, insert the Receipt Cover Keyto the Receipt Cover Lock, and turn it 90 clockwise. Depress the [JF] key to wind up enough of the JournalPaper, then cut the paper as shown in the figure. Depressthe [JF] key to feed the ...

- 68 - EO1-11113 1 2 3 4 Replacing the Ribbon Cassette When the print data on the receipt and journal becomes too dim, replace the Ribbon Cassette in thefollowing order. Remove the Ribbon Cover. Remove the old ribbon cassette by pulling it in the directionof the arrow mark. Install a new ribbon cass...

- 69 - EO1-11113 1 2 3 4 5 Replenishing Ink to the Store Name Stamp To remove the Receipt Cover, insert the Receipt Cover Keyto the Receipt Cover Lock, and turn it 90 clockwise. Remove the Store Name Stamp by pulling it in the directionof the arrow mark. Apply only two or three drops. Stamp may not ...

- 71 - EO1-11113 1 2 Fig. 4 CDC (Cash Drawer Cover; Option) Lock Locking (Fig.4) Push the Cash Drawer Cover to the back of the drawer. Press the cover lightly, insert the key into the key hole onthe cover, and turn it to lock. Unlock the cover using the key, and lift the front end. Unlocking

- 1 - EO1-11113 OTHER OPERATIONS OUTSIDE STORE’S BUSINESS HOURS .. .. . 1. DAILY OPERATION FLOW The following shows the typical flow of daily operations on the ECR. PAPER ROLL REPLACEMENT OR OTHER MAINTENANCE (OPERATOR’S GUIDE) CASHIER’S OPERATIONS (described in OPERATOR’S GUIDE) Sign-ON (or Cashier...

- 2 - EO1-11113 2. MANAGER INTERVENTION 2.1 MANAGER INTERVENTION During daily sale entry operations, the cashier may call for Manager Interventions. The following is theoperation flow of a Manager Intervention. 1) During operations, the cashier comes across an item that requires a Manager Interventi...

- 4 - EO1-11113 2.2 OTHER OPERATIONS REQUIRING MANAGER INTER- VENTIONS Amount Limit Release Amount Limits may be programmed on Departments/PLUs, Tender Medias, [DOLL DISC], [VND CPN],[STR CPN], [BTL RTN]. These limits are programmed to check an excessively high or low amount entryby cashier’s mistak...

- 5 - EO1-11113 3. MANAGER’S OWN OPERATIONS IN “MGR” MODE The following are operations possible only in the “MGR” position of the Mode Lock, which are performedby the manager or by a person under the manager’s control. 3.1. PICK UP OPERATION This operation is used when you collect money from the ECR...

- 7 - EO1-11113 4. OPERATIONS IN “ ” MODE Instead of using the [RTN MDSE] or [VOID] keys in the “REG” or “MGR” mode for deleting individual items,the “ ” mode automatically processes positive items into negative and negative into positive. To operate, turn the Mode Lock to the “ ” position using the...

- 8 - EO1-11113 3 (Custom File Code) [PICK UP BAL] 600 [DEPT 1] 10 [% –] [Chg] [TOTAL] 12-19-1994 MON #3001 * R E G - * P B + 000000000003 KAREN WALTERS $6.42VEGETABLE $6.00TF%- 10% -0.60TAX $0.36Chg $ 1 2 . 1 8 TOTAL $ 1 2 . 1 8 TOTAL $ 6 . 4 2 ITEM 1 * R E G - * SMITH 0223 16:51TM ** **** 12-19-19...

- 10 - EO1-11113 5. READ (X) AND RESET (Z) REPORTS The following table shows the key operation to take each report. The “X” and “Z” reports have exactly thesame print content if both are available, except that: 1. The “X” reports allow to read the sales data but not clear memories, while the “Z” rep...

- 12 - EO1-11113 203 [AT/TL] (Drawer opens.) 204 [AT/TL] (Drawer opens.) Code Entry Method: 204 [#] |Cashier ID Code| [AT/TL] (2-digit manager-assign code) Cashier Key Method: Set the required Cashier Key (ordepress the required Cashier Key),then 204 [#] [AT/TL] 206 [AT/TL] 208 [AT/TL] 27 211 [#], t...

- 13 - EO1-11113 Combination Reports Multiple reports can be programmed to be issued is one operation sequence. The following are reportsprogrammable for combinations (max. 5 reports in one table, max. 3 tables). Ask your TOSHIBA TECrepresentative for information of the contents of your Combination ...

- 14 - EO1-11113 GENERAL NOTES ON REPORT TAKINGS 1. The cashier signed-OFF or signed-OUT condition is required for taking any X or Z reports in the CodeEntry Method. (Otherwise, an error will result when the Mode Lock is turned to the “X” or “Z” position.)However, in case of a standalone system with...

- 17 - EO1-11113 CASHIER READ or RESET (Daily or GT) Mode Lock: X for read Z for reset (1) All Cashiers: Enter 4, depress [AT/TL] (for Daily). Enter 204, depress [AT/TL] (for GT). (2) Individual Cashier: Enter 4, depress [#], enter the Cashier ID Code (2 digits), and depress [AT/TL] (CODE ENTRY Meth...

- 27 - EO1-11113 PLU GROUP SALES READ or RESET (Daily or GT) Mode Lock: X for read Enter 24, depress [AT/TL] (for Daily). Z for reset Enter 224, depress [AT/TL] (for GT). Reset Report Format Sample PLU Group Name Item CountSales Percentage, Amount PLU Group Sales Reset Report Count (on Reset Reports...

- 28 - EO1-11113 6. PROGRAMMING OPERATIONS This chapter is provided for the store programmer or the store manager who may have to change theprogrammed data of the FS-1650 series ECR on the daily, weekly, or monthly basis. Usually, all thebasic program data required for your store should be set befor...

– 29 – EO1-11113 BASIC KEY FUNCTIONS AND KEYBOARD VARIATIONS INPROGRAMMING OPERATIONS Basic Key Functions 1. The following are main keys and their functions to be used in programming operations: [X] or [@/FOR] .... Used to enter the program Submode No. The [X] key is usually labeled as [@/ FOR] on t...

– 30 – EO1-11113 CHARACTER ENTRIES As already stated, there are two method of operations for character settings for names or messages:CHARACTER CODE ENTRY Method and DIRECT CHARACTER ENTRY Method. CHARACTER CODE ENTRY Method This method is to set a character by entering a Character Code and depressi...

– 31 – EO1-11113 2 3 4 5 6 7 8 9 10 11 12 13 14 15 00 0 @ P ` p á Å \ → 01 ! 1 A Q a q é å ll ← 02 " 2 B R b r  í Ø lll ↓ 03 # 3 C S c s  ó ø II ↑ 04 $ 4 D T d t ú Æ 05 % 5 E U e u • â æ 06 & 6 F V f v Ä ê Œ ★ 07 ′ 7 G W g w Ë î œ 08 ( 8 H X h x Ö ô ß kg 09 ) 9 I Y i y Ü û ¢ lb 10 ∗ : J Z ...

– 32 – EO1-11113 Character Setting Operations: • To set a regular-sized character, entry the COL (column) code and then the ROW code, followedby the [#] key. ex.) To set “%”, enter 205 and depress [#]. To set “kg”, enter 1508, and depress [#]. To set a blank instead of a character, simply depress [#...

– 33 – EO1-11113 Direct Character Entry Method Using Flat Keyboard (installed as the ECR Main Keyboard): -- Setting Mode Key Layout -- (Use the special template for this purpose and insert it between the film layers covering the Flat Keyboard.This key layout is applicable to only certain submodes.) ...

– 34 – EO1-11113 Using TKB-1 (Programming Keyboard; hardware option) Shift Keys (1 to 4), Shift Lock Key Used to designate the shift of the character keys. Each character has three different characters, eachof which is designated by the Shift Key 1 to Shift Key 3. (The Shift Key 4 is not used for th...

– 35 – EO1-11113 Function Keys Except for the [CODE] key, each of the function keys corresponds to the identical key installed on theECR keyboard as to the function in programming operations. ([CLEAR] = [C],[X] = [@/FOR]) The [CODE] key cannot be used for the FS-1650 series ECRs. Operation Examples ...

– 37 – EO1-11113 CONDITION REQUIRED FOR PROGRAMMING OPERATIONS At the top of each programming operation a “CONDITION” is given. Unless the register satisfies condition,the programming operations will not be allowed. There are two types of conditions: “Any time outside a sale” It means that the progr...

– 40 – EO1-11113 CASHIER CODE AND NAME PROGRAMMING (Submode 2) Programming Any time outside a sale Mode Lock: SET NOTES: 1. The following table shows the Cashier Codes that can be entered. (The capacity is determined by the RAM Allocation Setting.) Repeat for anothercashier. 2 [X] Character Entries(...

– 41 – EO1-11113 ex.) To program the following cashier data: Cashier Code 1: Name JONES, Status 0 (for Sale Entries)Cashier Code 2: Name SMITH, Status 0 (for Sale Entries)Cashier Code 3: Name MEAL, Status 1 (for Training Entries)Cashier Code 4: Name BROWN, Status 1 (for Training Entries) Mode Lock: ...

– 42 – EO1-11113 Deletion After the Daily and GT Cashier’s Resets, (and his/her Sign OFF for Code Entry Type) Mode Lock: SET NOTES: 1. The Cashier Reset Report Count of the deleted cashier will be cleared. 2. The cashier key or cashier code of the deleted cashier cannot be used or signed-ON for sale...

– 43 – EO1-11113 Address 1: Link Department 1 [ST] | Department Code | (1 to 99) Address 2: PLU Name 2 [ST] Character Entries max. 16 characters Address 3: Preset Price 3 [ST] Address 4: Status 1 Codes 4 [ST] Address 5: Status 2 Codes 5 [ST] 6 [ST] Address 8: Whole Package Quantity 8 [ST] Address 9:...

– 44 – EO1-11113 NOTES: 1) The “Address Nos” designation at the top after “4 [X]” can be skipped if not necessary. If entered, the designated Address (es) will automatically be accessed after the PLUCode designation. 2) A maximum of 1300 PLUs are programmable (varies depending on the capacity and al...

– 46 – EO1-11113 Address No. Description of Programming Contents -- Continued -- 8 Whole Package Quantity (for Split Package Pricing PLUs) [#] Enter the whole package quantity in max. 2 digits (1 to 99), or enter 0 tocancel the Split Package Pricing status. NOTES: • This setting is not allowed for P...

– 47 – EO1-11113 0: Non-taxable1: Add-on Tax 12: Add-on Tax 23: Add-on Tax 34: Add-on Tax 4 ex.) To program the following PLUs: PLUGroupNo. WholePackageQ'ty 10101 1 Tomato 1.00 4 0 1 6 1 10102 1 Potato 0.80 4 0 1 6 1 20101 2 Orange 0.75 4 0 1 4 1 20102 2 Lemon 1.00 4 0 1 4 1 20105 2 Apple 0.90 4 0 1...

– 48 – EO1-11113 P 0 4 010101PLU010101#01 01#02 Tomato#03 1.00@#04 4#05 0#06 1#08 6#09 01 090601PLU090601#01 09#02 Coke Small-B#03 0.60@#04 2#05 0#06 1#09 06 101301PLU101301#01 10#02 Small-Btl Depo#03 0.05@#04 0#05 0#06 1#09 13 00030 0026 TEC STORE 1343 PEACH DRIVE PHONE : 87-6437 Open 8:00am to 7:0...

– 49 – EO1-11113 Individual PLU Deletion [PLU] [AT/TL] ex.) To delete PLU No. 90701 (7-up Small-B) that wasonce programmed: Mode Lock: SET, enter 4, depress [X] [ITEM CORR] 90701 [PLU] [AT/TL] To delete a PLU with sales data of zero: Any time outside a saleTo delete a PLU with sales data of not zero...

– 50 – EO1-11113 PLU Programmed Data Copying This operation is used to copy the programmed data of a PLU item and to use it in programming an-other PLU item, thus eliminating time in PLU programming operation. To program new PLUs or to change any programmed contents of PLUs: Any time outside a sale ...

– 51 – EO1-11113 TIME SETTING OR ADJUSTMENT (Submode 5) Any time outside a sale Mode Lock: SET 5 [@/FOR] | Hour | | Minute | [AT/TL] (0 to 23) (00 to 59) NOTE: If an hour value of more than 23 or a minute value ofmore than 59 is entered, it will result in an error. Thecurrent date will not be change...

– 52 – EO1-11113 AMOUNT LIMIT SETTING FOR FUNCTION KEYS (Submode 8) This submode sets the high amount limit in finalizing transactions by tendering through each media keyand also sets the high and low amount limits in entering amount through departments. Any time outside a sale Mode Lock: SET 8 [@/F...

– 54 – EO1-11113 ex.) To program the following Customer File Codes with Customer Names: CODE NAME 1 JAMES HAILY 105 HELEN REED Mode Lock: SETEnter 15, depress [X] 1 [ST] (Customer File Code)JAMES HAILY [ST] (Name) 105 [ST](Customer File Code)HELEN REED [ST] (Name) [AT/TL] ex.) To delete Customer Fil...

– 55 – EO1-11113 SALESPERSON CODE AND NAME PROGRAMMING (Submode 20) By programming Salesperson Codes here, those codes may be used in sales entries. In addition, thename of each salesperson can be programmed in maximum 12 characters. Programming Any time outside a sale Mode Lock: SET 20 [X] | Salesp...

– 56 – EO1-11113 Deletion After Daily Salesperson Reset Mode Lock: SET 20 [X] [ITEM CORR] | Salesperson Code | [ST] [AT/TL] Repeat for other salespersons to be deleted. NOTE: When a Salesperson Code is deleted in the above operation, no entries using that codewill be accepted until the code is again...

– 57 – EO1-11113 LB unit kg unit 1: 1 LB 1 kg 9: 9 LB 9 kg 10: 1/2 LB 100 g 11: 1/4 LB Not applicable TARE TABLE AND GENERAL UNIT WEIGHT SETTING (Submode 26) In the PLU TABLE PROGRAMMING operation (Submode 4), some of Scale-compulsory PLUs may beset with a Tare Table No. The actual tare weight is se...

– 59 – EO1-11113 NOTES: 1. The Nos 1 through 130 marked on the PK-2 Keyboard are the KEY Nos to be printed on the left side of the program receipt issued in the operation on the preceding page.If each KEY is not set with a PLU Code, the auto-preset PLU Code identical to theinitial KEY No. in the abo...

– 62 – EO1-11113 This submode sets the limit amount to be entered through each of the negative-amount keys [VND CPN],[STR CPN], [BTL RTN], and [DOLL DISC]. Any time outside a sale Mode Lock: SET KEY CODE AND KEY TABLE Key Code Key 1 [VND CPN] 2 [STR CPN] 3 [BTL RTN] 4 [DOLL DISC] NOTES: 1. The respe...

– 64 – EO1-11113 DEPARTMENT PRESET PRICE SETTING OR CHANGING A price of each department may be set or changed by this operation. Any time outside a sale Repeatable for other departments. Repeatable for other departments. To change a preset-price department into an open department, skip the “New Pres...

– 66 – EO1-11113 Setting or Changing Preset Price of Split Package Pricing PLU Any time outside a sale Mode Lock: SET Repeatable for other PLUs * Repeatable from here if the PLU Code is sequential. ex.) To set the following preset price of PLUs: New Whole New Preset Package Q'ty Price PLU 20105 (App...

– 68 – EO1-11113 If any of [ST1/TL] (or [SI/TL]) and [SI2/TL] keys are installed on the keyboard, a preset rate may beprogrammed on each key. As for the functions and applications of the Selective Itemizers, refer to the description on the nextpage. Any time outside a sale Mode Lock: SET | Preset Ra...

– 69 – EO1-11113 Selective Itemizer Functions and Applications The “Selective Itemizer” is a temporary total memory for each sale and is activated separately from the MainItemizer (i.e. sale total memory). If certain Department or PLU items are programmed with the SI (selectiveitemizer) “net” status...

– 70 – EO1-11113 In this program, the rate of each foreign currencies (corresponding to the [CUR1] to [CUR5] keys) willbe set. By setting a rate on each Foreign Currency Key, reading the sale total and tendering in theforeign currency value will be possible for sale finalization. Any time outside a ...

– 71 – EO1-11113 P 0 0 CUR3 1.455 * 0048 TEC STORE 1343 PEACH DRI-VE PHONE : 87-6437 Open 8:00am to 7:00pm Closed : every Wednesday 12-19-1994 MON #1 P 0 0 CUR2 1.7619 * 0047 TEC STORE 1343 PEACH DRI-VE PHONE : 87-6437 Open 8:00am to 7:00pm Closed : every Wednesday 12-19-1994 MON #1 P 0 0 CUR1 5.372...

– 72 – EO1-11113 TAX TABLE PROGRAMMING A maximum of four tables can be programmed (Tax 1, Tax 2, Tax 3, Tax 4) in accodance with installa-tion of [TX1/M], [TX2/M], [TX3/M], [TX4/M] keys. After Financial Daily Reset Mode Lock: SET TYPE 1: TAX 1 FULL BREAKS (COMBINATION OF NON-CYCLIC AND CYCLIC BREAKS...

– 73 – EO1-11113 P 0 0 TAX100 $0.1001 $0.2202 $0.3903 $0.5604 $0.7305 $0.9006 $1.08 * 07 $1.2408 $1.4109 $1.5810 $1.7411 $1.9202 $2.08 ** 0058 NOTES: 1. For Tax 2, Tax 3, Tax 4 table programming, follow the same procedure in TYPE1,2, or 3 on the preceding page, using [TX2/M] or [TX3/M] or [TX4/M] in...

– 75 – EO1-11113 GST RATE SETTING This operation sets the rate of GST (Goods and Service Tax) in CANADA. Any time outside a sale Mode Lock: SET | GST Rate | [GST/M] To reset the rate once set: Mode Lock: SET Enter 0, depress the [GST/M] ex.)To set the GST rate to 12%: OPERATION Mode Lock: SET 12 [GS...

– 77 – EO1-11113 7. VERIFICATION OF PROGRAMMED DATA The programmed data entered in the preceding chapter can be read for verification purposes.The print format of each program reading is almost the same as on the program receipt, except that“PX” and a 3-digit number are printed instead of printing “...

– 78 – EO1-11113 P X $100.00TAX1 $6.00TAX2 $5.00TAX3 $4.00TAX4 $3.00 0076 Tax Calculation Test Any time outside a sale Mode Lock: X or SET Enter any amount. Depress [TXBL TL] NOTE: The print or non-print status of each calculated tax amount can be programmed. .. .. TEC STORE 1343 PEACH DRIVE PHONE :...

– 1 – EO1-11113 1. INTRODUCTION Making the most of the functions described in Standalone Section, the FS-1650 can be developed intoa master-satellite system. By adding the IFU Board for Master-Satellite, a Batch-consolidation system of a maximum of 6 termi-nals can be built. Operational functions on...

– 2 – EO1-11113 Master Terminal Backup Master Terminal Remote Slip Printer Scanner Scale Remote Slip Printer Scanner Scale Satellite Terminal Remote Slip Printer Scanner Scale Satellite Terminal Remote Slip Printer Scanner Scale Satellite Terminal Remote Slip Printer Scanner Scale Batch-consolidatio...

– 3 – EO1-11113 3. HARDWARE DESCRIPTION 3.1. COMMUNICATION SEQUENCE RS-485 Line 3.2. HARDWARE COMPOSITION A Master-Satellite System is realized by adding the IFU boards to each standalone ECR. 3.3. OPERATOR DISPLAY INDICATIONS OF MASTER-SATELLITE SYSTEM ■ Display Indications during In-Line Services ...

– 4 – EO1-11113 Error Message (Sandard Setting) FILE BUSY A designated file is already occupied by other terminal. IRC CONNECT ERR Ternsmission cannot be executed due to the connection error (Disconnection of the line, or Master Terminal’s power is OFF, etc.) IRC ERROR RKP Transmission Error (Data c...

– 5 – EO1-11113 4. ADDITIONAL FUNCTION KEY ANDREGISTERING PROCEDURE The following is the key that can be installed on the Master Terminal of an in-line system, in addition tothe standalone specifications, and the registering procedure using the key. RTR (Register-to-Register) DECLARATION Key ([RTR])...

– 1 – EO1-11113 1. DAILY OPERATION FLOW In a Master-Satellite System, a certain order of jobs on the Master and Satellite terminals are pro-vided. If the necessary jobs are not proceeded in the correct order, sale entries may not be oper-ated or report collections may not be possible. The following ...

– 2 – EO1-11113 Sign OFF on all the terminals (including the Master Terminal) when all the saleentries for the day are over. In-Line Reset Report Takings on MasterTerminal. (Refer to Section 3.2.) The “HOLD” condition of the terminal can not be released for some reason, an“ENFORCED CLEAR OF HOLD CON...

- 3 - EO1-11113 2. OPERATIONS BEFORE IN-LINE SERVICE Before entering in-line service operations (In-line Report takings, DLLs, etc.), the following opera-tions are available if necessary. TERMINAL OPEN CHECK This operation sends a dummy text to those terminals set in the TERMINAL CONNECTION TABLE(Su...

- 4 - EO1-11113 TERMINAL DESIGNATION This operation can be performed before any in-line service operation. When this operation isskipped, no specific terminals are designated, i.e., the in-line service operations will be performedto all the terminals. Any time outside a sale Mode Lock: SET, X, or Z ...

- 5 - EO1-11113 TERMINAL CONDITION CHECK This operation checks the condition of the designated terminals, and prints out the status re-sponded from the terminals. Any time outside a sale (operable on Master Terminal) Mode Lock: X and IN-LINE Lamp illuminated 81 [AT/TL] Master Terminal Receipt Print ...

- 6 - EO1-11113 3. READ AND RESET REPORTS 3.1. TERMINAL REPORTS Since most reports are taken as in-line reports on the Master Terminal, some of the reports whichare available on the individual standalone ECR basis cannot be taken on Master or SatelliteECRs of the in-line system. The following are th...

- 7 - EO1-11113 3.2. IN-LINE REPORTS 3.2.1. IN-LINE REPORT COMMAND EXECUTIONS Before taking in-line reports, please note the following: 1) In-line Reset Reports (as well as In-line Read Reports) can be taken on the Master Terminal as long as the Satellite Terminals are in the idle state (“Signed OFF...

- 8 - EO1-11113 To be operated on the Master Terminal only Designating All Terminals Designating Some Terminals Repeat for allthe terminalsto bedesignated. Store/Register No. of the terminal to bedesignated (max. 6 digits) [#] [#] [AT/TL] Report Taking Operation for Each Report (see the following pa...

- 14 - EO1-11113 JOURNAL INDICATIONS ON INDIVIDUAL TERMINALS (when report data is collected) 3.3. OPERATIONS AFTER IN-LINE REPORT TAKINGS The following operations are available after taking in-line reports. CONSOLIDATED REPORT DATA READ (REPRINT) This operation issues the report data which is remain...

- 15 - EO1-11113 PROGRAMMING JOB LIST Master: Programming is available on the master terminal (when the [RTR] key is turned onor the INLINE lamp is on). Satellite: Programming is available on the master terminal (when the [RTR] key is turned offor the INLINE lamp is off), the backup master terminal ...

- 16 - EO1-11113 PROGRAMMING OPERATIONS ADDED FOR IN-LINE TERMINALS TABLE OF PROGRAMMING OPERATIONS AFTER ADDITION (The page No. is the one in this manual) (page) Submode 69: TERMINAL CONNECTION TABLE (added for Master Terminal only) ...................... 17 Submode 77: TERMINAL ID SETTING ...........

- 17 - EO1-11113 TERMINAL CONNECTION TABLE SETTING (Submode 69) This submode is required for in-line services. Enter the In-line ID No. and the Register No. of eachterminal (including the Master Terminal) connected to the in-line cable. Any time outside a sale Mode Lock: SET and IN-LINE Lamp illumin...

- 20 - EO1-11113 NOTE: DLL is possible only when the non-floating cashier feature is used. Store Name/Message and Commercial Message ProgrammingCashier Code and Name ProgrammingPLU Table ProgrammingTime/Date SettingAmount Limit Setting for Function KeysSalesperson Code and Name ProgrammingTare Table...

- 21 - EO1-11113 Terminals including the Master: Any time outside a sale(Sign OFF condition is not necessarily required for the Code Entry Method) Satellite Terminals: Any position if the power is ON Master Terminal: Mode Lock: SETRTR Declaration: ON PRINT FORMAT OF DLL OPERATIONS Master Terminal Re...

- 22 - EO1-11113 6. DEPARTMENT AND PLU MAINTENANCE In this chapter, adding, changing, or deleting operation related to Department Table and PLU Tableprogram data are described. These are operated on the Master Terminal only. All of these opera-tions are loaded into Satellite Terminals at the same ti...

- 23 - EO1-11113 Address 12: Unit Weight (max. 6 digits) PLU TABLE ADDITION/CHANGE/DELETION WITH DLL (Submode 63) This submode can be operated only on the Master Terminal in an in-line system. This submode allowsadditions/changes/deletions of PLUs in the PLU Table File (generated by Submode 4 in the...

- 24 - EO1-11113 * Deletion The sales data of the required PLUs are zero and all terminals are outside asale, programming, or report taking operations. Mode Lock: SET and IN-LINE Lamp illuminated DEPARTMENT PRESET PRICE SETTING OR CHANGING WITH DLL(Submode 72) This submode is used to newly set or ch...

– 26 – EO1-11113 7. INQUIRIES This chapter describes various inquiries made from each terminal to the Master Terminal and affectdata (sales data updating). 7.1. CASHIER OCCUPY INQUIRIES When the “Floating Cashier” feature is selected and a Cashier Code is entered on a terminal, theterminal inquires ...

– 27 – EO1-11113 7.3. RKP PRINT DATA TRANSMISSION AND RKP CONDITION CHECK INQUIRIES RKP PRINT DATA TRANSMISSION RKP print data from each terminal is transmitted to the Master Terminal and/or the BackupMaster Terminal, and the print outputted from the RKP becomes possible. RKP CONDITION CHECK INQUIRI...

– 28 – EO1-11113 8. BACKUP FUNCTION (ONLY WHEN THE BACKUP MASTER IS CONNECTED) (1) Function • By connecting the backup master terminal (BM), the various files stored in the master terminal(M) can be backed up. • The terminal assigned to ID No. 2 will function as a backup master terminal (BM). By pro...

– 30 – EO1-11113 4) Checking Backup Data • The master terminal (M) sends the version request command to the backup master termi-nal (BM) every certain period of time and receives version information about the backupdata. • The master terminal (M) checks correspondence between the version information...

– 31 – EO1-11113 6) Backup Data Update Process (This is a process required when the backup data stored in the backup master terminal (BM) isnot updated properly due to an error.) • The method processing backup error is selected according to the program option setting.Even if the automatic data copy ...

– 32 – EO1-11113 9. MASTER AND BACKUP MASTER ALTERNATION The Backup Master Terminal can be changed to be used as the Master Terminal for an accident thatthe Master Terminal becomes down, etc. And the Master Terminal can be changed to be used asthe Backup Master when it comes back from repair, etc. T...

– 33 – EO1-11113 For Retry .............. [AT/TL] (Performs re-sending to the other station.) For Cancel ........... [X] [ST] (Stops the inquiry, printing on journal “ ** X ST ** ”) NOTE: The “Cancel” in Type 2 above is for only the case the other station is in trouble whichcannot be recovered by a ...

– 35 – EO1-11113 TIME OUT A Time-Out condition arises when the Master Terminal is making an in-line service operation, suchas X/Z report collection, DLL, etc. to the Satellite Terminals. The service timer is provided forservicing each of the Satellite Terminals, thus on exceeding the time limit, a T...

– 36 – EO1-11113 SUSPENDING This is to be operated for the purpose of suspending an in-line service being executed, when anyterminals remain unserviced, and of going on to a “RETRY”, “INCOMPLETE ENDING”, or “CAN-CEL” operation as the next step. OPERATION ON MASTER TERMINAL: (Same Lock positions as t...

– 37 – EO1-11113 As part of the print out, the Store/Reg. No. of the terminal and its status will be printed. CANCEL This can be operated when a SUSPENDING condition arises due to a TIME OUT or a SUSPEND-ING operation. The entire in-line service being performed is canceled. This operation is effecti...