Toshiba 52X3000A - Manuals

5 Introduction 5) When the TV will not be used for a long period of time, such as during vacation or travel, remove the power plug from the wall outlet for safety. • The TV is not completely disconnected from the power supply line, as minute current is consumed even when the ! Power switch is turned...

6 Introduction Cleaning 1) Remove the power plug before cleaning. Never use solvents such as benzine or thinner to clean the TV.• These solvents may distort the cabinet or damage its finish. • If rubber or vinyl products remain in contact with the TV for a long time, a stain may result. If the cabin...

7 Getting started Connecting an antenna Optimum reception of color requires a good signal and will generally mean that an outdoor antenna must be used. The exact type and positioning of the antenna will depend upon your particular area. Your Toshiba dealer or service personnel can best advise you on...

8 Getting started TV front and side panel controls • You can operate your TV using the buttons on the side panel or the remote control. The back and side of the panel provide the terminal connections to connect other equipment to your TV ( - “Connecting your TV” pages 33 - 37). • For the use of each...

9 Getting started TV back panel connections AV OUTPUT PC/HDMI1 (AUDIO) TV back view Cable holder* Power cord 15 12 13 14 16 17 18 19 * You can use the cable holder to hold antenna cable, video and audio cables etc. When moving the TV, never hold this holder. 12 o (1) (Video 1 input terminals) — High...

10 Getting started Learning about the remote control Location of controls To switch between Analog and Digital TV ( - page 12) To return to the previous program ( - page 16) To display digital on-screen information ( - page 29) MENU ( - page 12) • Menu ( - page 12) • OK ( - pages 12, 25) Program pos...

11 Getting started Turning the TV on Switching on the TV Connect the power cord to a wall outlet, the ! power indicator lights in red (standby mode). 1 Press on the remote control or ! on the TV right side panel, the ! power indicator lights in green. Note: If you watch black and white programs when...

12 Getting started This integrated TV is equipped with both Digital and Analog system. To switch between Digital and Analog TV press A/D on the remote control. Learning about the menu system We suggest you familiarize yourself with the display charts before using the menu system: • Press M to displa...

13 Getting started Notes for menu system: • In the video input mode ( o 1 , o 2 ), Auto tuning and Manual tuning are not available. Instead, Manual setting appears in the SET UP menu ( - page 26). • If you connect external equipment via component video source to external input, Color system selectio...

14 Getting started Note: After the Auto scan , the TV may have scanned identical channels being broadcast from different transmitters. You can verify this by previewing those channels in the Channel List with identical logical numbers and check on their physical channel numbers ( - page 30). If you ...

15 Getting started Manually setting channels in the channel memory - analog only - Use the Manual tuning operation if desired channels cannot be preset with the Auto tuning or if you would like to preset channels to specific position numbers one by one. 1 From the SET UP menu, press or to select Man...

16 Getting started Watching TV programs Viewing Digital programs - digital only - After you have tuned the TV, you have several ways to navigate through all programs: • Press the Number buttons (a channel number has 4-digits) and you may omit the leading zeroes, which will be appended automatically;...

17 Getting started I-Plate contains the following information: • Current Channel Number• Channel Name• Favorite status (indicated by a heart icon)• Channel Lock status (indicated by a padlock icon on first I-Plate) • Now and Next Program Names• Current date and time• Received program video format (S...

18 Using the TV’s features (General) Picture adjustment Selecting the picture size 1 Press O to display the picture size list, then press or to select the appropriate picture size (or press O repeatedly to select required picture size directly). 2 Press Q . Wide Use this setting when watching a wide...

19 Using the TV’s features (General) PC Use this setting for PC via HDMI. When receiving 1080i, 1080p or 720p signal format of HDMI input, this setting will display the image correctly without distortion or picture clipping. Notes: • Using the special functions to change the size of the displayed im...

20 Using the TV’s features (General) Adjusting the basic picture quality 1 In Digital TV, press , M then press or to display the TV set up then press Q . 2 Press or to display the PICTURE menu. 3 In Analog TV, press M and or to display the PICTURE menu. 4 Press or to select the Picture settings menu...

21 Using the TV’s features (General) 5 Press , then press or to select Hue , Saturation or Brightness . 6 Press or to adjust the settings as required. Notes: • If you select color management Off mode, this mode is not available. • In the PC input mode ( - page 25), this mode is not available. Resett...

22 Using the TV’s features (General) Sound adjustment Setting the MTS (Multi-channel TV Sound) - analog only - Auto mode The MTS Auto mode automatically recognize stereo/bilingual programs depending on the broadcast signal. 1 Press M , then press or to display the SOUND menu. 2 Press or to select MT...

23 Using the TV’s features (General) Using the SRS WOW ® surround sound SRS WOW ® is a special combination of SRS Labs audio technologies that creates a thrilling surround sound experience with deep, rich bass from stereo sound sources. Your TV’s audio will sound fuller, richer and wider. WOW ® cons...

24 Using the TV’s features (General) The timers Setting the Time zone - digital only - This function allows you to manually set the time zone and override the location that you have chosen during Auto Scan. This is to be used when you move out of Australia to country with different time zone. Please...

25 Using the TV’s features (General) Setting the Alarm - digital only - This function will turn on the TV to go to a specific TV mode or channel at a certain time. 1 From the PROGRAM menu. 2 Press or to select Alarm , then press Q . 3 Press or to select Mode and or to choose Off , Once , Mon-Fri or ...

26 Using the TV’s features (General) Setting the manual setting menu - analog only - 1 Press M , then press or to display the SET UP menu. 2 Press or to select Manual setting , then press Q . 3 Press or to select an item, then press or to select the item as shown below. A. Color System Confirm that ...

27 Using the TV’s features (General) Using Auto mode There are two Modes: Auto will display FASTEXT or TOPTEXT, if available. LIST will display your four favorite pages. In either mode, as an alternative to the colored buttons, you can access a page by entering a 3-digit number, using the Number but...

28 Using the TV’s features (General) Teletext buttons on the remote control Below is an introduction to the teletext buttons on your remote control and their functions. k To display an index/initial page: In Auto-mode Press k to access the index page. The one displayed is dependant on the broadcaste...

29 Other Digital TV features and settings Setting the EPG (Electronic Program guide) 1 Press M , then or to select PROGRAM menu. 2 Press or to select EPG then, press Q to display EPG . Alternatively, press a to display EPG directly. 3 Press and to select the channel, names of the program being broad...

30 Other Digital TV features and settings Parental rate The type of program displayed on the TV can be limited based on the parental guidance codes. See Appendix for Australian parental guide code. Setting the parental rate 1 Press M , then press or to select the PROGRAM menu. 2 Press or to select P...

31 Other Digital TV features and settings Favorite Channel List 1 When viewing in Digital TV, press to display the Navigation list. 2 Press again to display Favorite Channel list. 3 Press and to select your favorite channel, then press Q . Favorite Mode This function enables or disables the favorite...

32 Other Digital TV features and settings Audio Preference Selecting The Audio Mode 1 From the PROFILE menu, press or to select Audio Preference , then press Q . 2 Press or to select Audio Mode . 3 Press or to select Dolby D or MPEG . Dolby D : If you select this option, the TV will select the first...

33 Connecting your TV Back connections Connection example • Before connecting any external equipment, turn off all main power switches. • The unauthorized recording of television programs, DVDs, video tapes and other materials may infringe upon the provisions of copyright law. • If you connect both ...

34 Connecting your TV Connecting an amplifier equipped with a Dolby Digital decoder You can enjoy dynamic realistic sound by connecting the TV to an amplifier equipped with a Dolby Digital decoder or Dolby Digital processor. When using this setup, select Bitstream in Digital Output menu. Connecting ...

35 Connecting your TV Side connections You can connect a wide variety of auxiliary equipment via the terminals located on the right side of the panel o (2) . Please always refer to the owner’s manual of the equipment to be connected for full details. Connection example • To select the side inputs, p...

36 Connecting your TV Connecting an HDMI device One HDMI cable (type A connector) For proper operation, it is recommended that you use a short HDMI cable. HDMI cable transfers both video and audio. Note: It is possible that some HDMI device may not operate properly with this TV. Connecting a DVI dev...

37 Connecting your TV Selecting the AV output mode You can select the AV output from three modes; ATV , DTV or Monitor . 1 From AV Connection menu, press or to select AV Output . 2 Press or to select the desired output mode. ATV : Selected programmed channel from Analog TV system is output from the ...

38 Connecting your TV To connect a PC to the HDMI terminal on the TV: When connecting a PC to the HDMI terminal on the TV, use an HDMI-to DVI adapter cable and analog audio cables. If connecting a PC with an HDMI terminal, use an HDMI cable (type A connector). Separate analog cables are not necessar...

39 Reference section Troubleshooting Before calling a service technician, please check the following table for a possible cause of the symptom and some solutions. Symptom and solution TV will not turn on • Make sure the power cord is plugged in, then press ! or 1 . • The remote control batteries may...

40 Reference section APPENDIX AUSTRALIAN PARENTAL GUIDANCE CODES (Normative) Recommended On-Screen-Display for parental guidance codes transmitted within DVB-SI EIT information using the DVB parental_rating_descriptor. Re c eiver Men u Set- u p an d S u gge s te d OSD wor d ing for Setting Blo c kin...

41 Reference section Broadcast system Broadcast transmission systems of each country or region Asia M.E. Oceania Africa South America Note: PAL, SECAM and NTSC 3.58 (MHz) are different color signal broadcast transmission systems applicable to different countries or region. NTSC 4.43 (MHz) is used in...