Toro 88710 - Manuals

Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any areaof potential danger. Replace any decal that is damaged or missing. decal145-3141 145-3141 decal139-5210 139-5210 1. Warning—read the Operator’s Manual ; stay away from movin...

Setup Connecting the Attachment to the Power Head 1. Install the square shaft of the attachment into the square shaft of the power head (A of Figure 3 ). 2. Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shaftstogether (B and C of Figure 3 ). 3. ...

Product Overview g367403 Figure 4 1. Shaft 4. Wheel height adjustmentknob 2. Guard 5. Wheel 3. Edger blade Specifications Model 88710, attaches to 51810T Blade Length 203 mm (8 inches) Rated Voltage 60V DC maximum, 54 VDCnominal usage No-load Max Speed 7000 rpm Weight (without batterypack) 4.6 kg (1...

Operation Starting the Attachment 1. Ensure that the vents on the attachment, powerhead, and battery are clear of any dust anddebris. 2. Align the cavity in the battery pack with thetongue on the handle housing ( Figure 5 ). g357444 Figure 5 3. Push the battery pack into the handle until thebattery ...

Adjusting the Depth of Cut 1. Remove the battery from the edger. 2. Loosen the knob on the wheel and move it up ordown in the track to increase or decrease thedepth ( Figure 8 ). g367405 Figure 8 1. Wheel knob 3. Adjust the depth so that the blade barely touchesthe ground when the machine is held in...

Maintenance After each use of the edger, complete the following: 1. Remove the battery from the edger. 2. Wipe the edger clean with a damp cloth. Do nothose the edger down or submerge it in water. 3. Wipe or scrape clean the cutting head area anytime there is an accumulation of debris. 4. Check and ...

Storage Important: Store the tool, battery pack, and charger only in temperatures that are within theappropriate range; refer to Specifications (page 8) . Important: If you are storing the battery pack for the off-season, remove the battery pack from thetool and charge the battery pack until 2 or 3 ...

Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair workmust be performed by an authorized service center or a similarly qualified specialist if you cannot solve theproblem yourself. Problem Possible Cause Corrective Action 1. The b...

California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in C...

Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any areaof potential danger. Replace any decal that is damaged or missing. decal139-5346 139-5346 decal139-5210 139-5210 1. Warning—read the Operator’s Manual ; stay away from movin...

Setup Connecting the Attachment to the Power Head 1. Install the square shaft of the attachment into the square shaft of the power head (A of Figure 3 ). 2. Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shaftstogether (B and C of Figure 3 ). 3. ...

Product Overview g367403 Figure 4 1. Shaft 4. Wheel height adjustmentknob 2. Guard 5. Wheel 3. Edger blade Specifications Model 88710, attaches to 51810T Blade Length 203 mm (8 inches) Rated Voltage 60V DC maximum, 54 VDCnominal usage No-load Max Speed 7000 rpm Weight (without batterypack) 4.6 kg (1...

Operation Starting the Attachment 1. Ensure that the vents on the attachment, powerhead, and battery are clear of any dust anddebris. 2. Align the cavity in the battery pack with thetongue on the handle housing ( Figure 5 ). g357444 Figure 5 3. Push the battery pack into the handle until thebattery ...

Adjusting the Depth of Cut 1. Remove the battery from the edger. 2. Loosen the knob on the wheel and move it up ordown in the track to increase or decrease thedepth ( Figure 8 ). g367405 Figure 8 1. Wheel knob 3. Adjust the depth so that the blade barely touchesthe ground when the machine is held in...

Maintenance After each use of the edger, complete the following: 1. Remove the battery from the edger. 2. Wipe the edger clean with a damp cloth. Do nothose the edger down or submerge it in water. 3. Wipe or scrape clean the cutting head area anytime there is an accumulation of debris. 4. Check and ...

Storage Important: Store the tool, battery pack, and charger only in temperatures that are within theappropriate range; refer to Specifications (page 8) . Important: If you are storing the battery pack for the off-season, remove the battery pack from thetool and charge the battery pack until 2 or 3 ...

Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair workmust be performed by an authorized service center or a similarly qualified specialist if you cannot solve theproblem yourself. Always remove the battery from the tool when trou...

California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in C...