Toro 69X-06-XX - Manuals - manualsarea.com

Page 2 - Construct triple swing joints for each sprinkler as shown in; CAUTION; Triple Swing Joints; MODEL NUMBER CODE; Spacing of Sprinklers

2 Performance Chart Installation Procedure To assure maximum performance from your 690 Series RotarySprinklers, read these instructions completely prior to installing orservicing the sprinkler. Construct Swing Joints 1. Construct triple swing joints for each sprinkler as shown in Figure 1. Use PVC o...

Page 3 - Connecting Electric Control Wires; Attach control wires to solenoid leads using an; Connecting Hydraulic Control Tubing; Flush tubing thoroughly to remove all air and debris.; Table 2; Table 1 - Wire Sizing Chart

Connecting Electric Control Wires 1. Route control wires to sprinkler location(s). Provide e n o u g h e x t r a w i r e a t s p r i n k l e r t o a l l o w f o rm o v e m e n t o f s p r i n k l e r w i t h o u t s t r a i n i n g w i r econnections. One common wire and one stationwire are required...

Page 4 - Pilot Valve; PROBLEM; Sprinkler will not turn on; Coverage Area

Two-Speed Sprinkler Alignment - Models 696 and 698 There are two types of full circle sprinklers which have special arcs of slower then regular speed. Alignment ofthe heads is critical for proper performance. The model 696 sprinkler is a two-speed head with two 60° and two120° arcs of speed. A red b...

Page 5 - Sprinklers

5 System Troubleshooting (continued) Sprinklers Possible equipment failures with causes and corrective action are listed below. PROBLEM POSSIBLE CAUSE – CORRECTIVE ACTION 1. Sprinkler won't rotate (a) Stator too large for nozzle - Use proper nozzle.(b) Debris wedged between stator and turbine - Remo...

Page 6 - Servicing Procedures; Introduction; Servicing Sprinkler Mechanism and Valve Assembly; WARNING

Servicing Procedures Introduction The 690 Series rotary sprinkler is designed to provide the user trouble free operation for many years withoutscheduled maintenance. Should it become necessary to disassemble the sprinkler to correct a malfunction orreplace a component, all internal parts of the spri...

Page 7 - To reinstall valve assembly with snap ring; Figure 6; Using Valve Insertion Tool to Install Valve Assembly; Figure 4; Using Snap Ring Pliers to Remove Snap Ring; Figure 5; Using Valve Removal Tool to Remove Valve Assembly

13. To reinstall valve assembly with snap ring and to prevent damage to thecommunication tube in sprinkler body, usevalve insertion tool (P/N 995-11). Valveinsertion tool will automatically line up valveassembly with sprinkler body communicationtube and correctly seat the snap ring. (SeeFigure 6). N...

Page 8 - Servicing Pilot Valve Assembly; Refer to Figure 7 for the following procedure.

8 Servicing Pilot Valve Assembly Note: Assure water supply to sprinkler is positively shut off and all residual pressure has been bled. If sprinkleris pressurized, main valve will open when the pilot valve control tube is disconnected. Refer to Figure 7 for the following procedure. 1. Carefully remo...

Page 9 - Figure 7 Pilot Valve, Current; Nomenclature

9 Figure 7 Pilot Valve, Current Item No. Part No. Nomenclature Quantity Per Assy. 1 89-1905 Solenoid, Pilot Valve & Valve 1 2 89-6005 Adapter, Pilot Valve, NC 1 3 89-0001 Housing, Pilot Valve 1 4 360-0220 O-Ring, .070" x .551" x .691" 1 5 35-9993 Plunger Assy., Elec. 1 6 89-6003 Plun...

Page 10 - Model Number Information

10 Figure 8 690 Series 6 9 X - X X - X X X Arc Body Nozzle Pressure Regulation * 1 = 90° Quarter Circle 01 = NPT, NO Valve-In-Head 90 8 = 80 PSI 2 = 180° Half Circle 02 = NPT, Check-O-Matic 91 1 = 100 PSI 4 = Full Circle 06 = NPT, Electric Valve-In-Head 92 6 = Full Circle, 2-Speed, 08 = NPT, NC Valv...