Toro 51810T - Manuals

Setup 1 Installing the Auxiliary Handle Parts needed for this procedure: 1 Auxiliary handle assembly Procedure 1. Separate the auxiliary handle from the handle plate by removing the 4 socket head screws using theprovided Allen wrench (A of Figure 3 ). 2. Line up the auxiliary handle with auxiliary h...

3 Installing the Battery Guard Rod Parts needed for this procedure: 1 Battery guard rod Procedure 1. Align the arms of the guard rod with the guide on the power head. 2. Lightly pull the arms of the guard rod so that they fit around the power head, and fit the rod ends into themounting holes. g38536...

Product Overview g372329 Figure 5 1. Battery latch 4. Harness/strap collar(harness/strap soldseparately) 2. Run trigger 5. Auxiliary handle 3. Lockout button Specifications Model 51810T Charger Type Toro 60V lithium-ion chargers Battery Type Toro 60V lithum-ion batteries Appropriate Temperature Rang...

Operation Starting the Attachment WARNING Do not attempt to operate the power headwithout an attachment installed. Read and follow the Operator’s Manual for your specific attachment before operating thepower head. 1. Ensure that the vents on the attachment, powerhead, and battery are clear of any du...

Removing the Attachmentfrom the Power Head To remove the attachment from the power head, referto the Operator’s Manual for your attachment. Maintenance After each use of the power head, complete thefollowing: 1. Remove the battery from the power head. 2. Wipe the power head clean with a damp cloth.D...

Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair workmust be performed by an authorized service center or a similarly qualified specialist if you cannot solve theproblem yourself. Always remove the battery from the tool when trou...

California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in C...

Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any areaof potential danger. Replace any decal that is damaged or missing. decal145-3141 145-3141 decal139-5210 139-5210 1. Warning—read the Operator’s Manual ; stay away from movin...

Setup Connecting the Attachment to the Power Head 1. Install the square shaft of the attachment into the square shaft of the power head (A of Figure 3 ). 2. Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shaftstogether (B and C of Figure 3 ). 3. ...

Product Overview g367403 Figure 4 1. Shaft 4. Wheel height adjustmentknob 2. Guard 5. Wheel 3. Edger blade Specifications Model 88710, attaches to 51810T Blade Length 203 mm (8 inches) Rated Voltage 60V DC maximum, 54 VDCnominal usage No-load Max Speed 7000 rpm Weight (without batterypack) 4.6 kg (1...

Operation Starting the Attachment 1. Ensure that the vents on the attachment, powerhead, and battery are clear of any dust anddebris. 2. Align the cavity in the battery pack with thetongue on the handle housing ( Figure 5 ). g357444 Figure 5 3. Push the battery pack into the handle until thebattery ...

Adjusting the Depth of Cut 1. Remove the battery from the edger. 2. Loosen the knob on the wheel and move it up ordown in the track to increase or decrease thedepth ( Figure 8 ). g367405 Figure 8 1. Wheel knob 3. Adjust the depth so that the blade barely touchesthe ground when the machine is held in...

Maintenance After each use of the edger, complete the following: 1. Remove the battery from the edger. 2. Wipe the edger clean with a damp cloth. Do nothose the edger down or submerge it in water. 3. Wipe or scrape clean the cutting head area anytime there is an accumulation of debris. 4. Check and ...

Storage Important: Store the tool, battery pack, and charger only in temperatures that are within theappropriate range; refer to Specifications (page 8) . Important: If you are storing the battery pack for the off-season, remove the battery pack from thetool and charge the battery pack until 2 or 3 ...

Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair workmust be performed by an authorized service center or a similarly qualified specialist if you cannot solve theproblem yourself. Problem Possible Cause Corrective Action 1. The b...

California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in C...