Toastmaster MBT240 - Manuals

Page 2 - boldface letter

2 INTRODUCTION Batch Toaster Information The Model MBT208/MBT240 Batch Toaster is a com- mercial batch toaster designed to uniformly toast En- glish muffins, bagels, and other bakery products in large quantities. Up to six individual program settings can be selected and programmed to toast a wide va...

Page 3 - SPECIFICATIONS; Overall Dimensions

3 SPECIFICATIONS Overall Dimensions Width 17-1/2 (445mm) Depth (inc. rear cord clearance, peel removed) 28 (711mm) Depth (inc. rear cord clearance, peel in toaster) 32 (813mm) Height (inc. legs) 10-1/2 (267mm) Toasting Area Dimensions Width, Loading Area of Peel 11-1/4 (286mm) Length, Loading A...

Page 4 - It is the customers responsibility to report any con-; IMPORTANT; The Batch Toaster may only be installed in a single-; Assembly; INSTALLATION; Figure 1 - Moving the Door Handle to the Right Side of the Toaster

4 IMPORTANT It is the customers responsibility to report any con- cealed or non-concealed damage to the freight com- pany. IMPORTANT The Batch Toaster may only be installed in a single- unit, countertop configuration. Assembly 1. Pull the door handle up and forward to open the door. Then, remove al...

Page 5 - Checking the Installation; CAUTION - HOT SURFACES; Electrical Connection

5 2. Check that the appropriate receptacle is available for the power cord plug. 3. Insert the power cord plug into its receptacle. 4. If required by national or local codes, connect an equipotential ground wire to the lug next to the symbol (shown in Figure 3). The equipotentialground connection mu...

Page 6 - Setup; Operation; CAUTION; Leaving the product; Figure 4 - Control Panel Functions: Operating Mode

6 CAUTION - HOT SURFACES D U R I N G O P E R A T I O N , T H E P E E L A N D TOASTER ARE HOT. USE CAUTION AS YOU HANDLE THE PEEL AND OPERATE THE TOASTER TO AVOID INJURY. Setup 1. Replace the lower deck inside the toaster.2. Switch the circuit breaker/fused disconnect to the ON (I) position. 3. Swi...

Page 7 - Programming; Figure 5 - Control Panel Functions: Programming Mode

7 Programming The Batch Toaster is pre-programmed with standard menu programs at the factory. Perform the following steps ONLY if you wish to change a programs settings. IMPORTANT Programming a new menu program will OVERWRITE an existing program. Do not overwrite a program that you wish to keep! Re...

Page 8 - Close; WARNING

8 Close 1. Switch the switch to the OFF (O) position. The fan will remain in operation to allow the toasterto cool. 2. After the fan stops, switch the circuit breaker/fused disconnect to the OFF (O) position. 3. Cleaning the Peel and Lower Deck CAUTION - HOT SURFACES DO NOT TOUCH HOT SURFACES ON...

Page 9 - TROUBLESHOOTING; PROBLEM

9 TROUBLESHOOTING PROBLEM Product is toasted t o o d a r k o r t o o light. PROBABLE CAUSE Toaster was not adequately preheated. Preset toasting time is incor- rect. Using refrigerated or frozen bakery products. CORRECTIVE ACTION Allow toaster to preheat until (ready) ap- pears in the display. This ...

Page 10 - PARTS IDENTIFICATION AND FUNCTION

10 PARTS IDENTIFICATION AND FUNCTION 37 38 5 7 6 9 29 28 10 8 28 25 28 22 24 16 17 36 36 20 19 35 36 36 32 12 13 21 31 2 30 28 24 23 41 11 27 40 39 30 14 1 26 15 18 3 34 33 4 28 28 42

Page 11 - Parts List

11 Parts List 1 41706 1 PANEL, LEFT SIDE 2 39806 1 PANEL, RIGHT SIDE 3 32458 1 PANEL, REAR 4 41902 1 PANEL, SSR MOUNTING 5 39804 1 LOWER DECK 6 42482 1 CONTROL PANEL 7 41837 1 DECAL, CONTROL PANEL 8 41733 1 TIMER BOARD 9 35824 1 SWITCH, POWER ON/OFF 2-POLE 10 43161 4 LEG, 1-1/2 (38mm) 11 41805 1 HI...

Page 12 - ORDERING AND SERVICE INFORMATION; Ordering Parts; Toastmaster; DESCRIPTION

12 ORDERING AND SERVICE INFORMATION Ordering Parts Use only genuine Toastmaster (manufacturer) replacement parts in your toaster. Use of parts other than those supplied or approved by Toastmaster will void the toasters warranty and agency approval.If your toaster requires a replacement part, locate...

Page 13 - NOTES

Page 14 - ELECTRICAL WIRING DIAGRAM; Wiring Diagram Notes:; Heating elements are numbered back-to-front

14 ELECTRICAL WIRING DIAGRAM TERMINAL BLOCK TSTAT NC HI LIMIT TSTAT NO COOL DN FAN CONTACTOR POWER ON/OFF (I/O) SWITCH HEATING ELEMENTS TRANSFORMER 230Vp : 24Vs TIMER BOARD AC IN R3 R2 R1 12V+ + - + - + - RELAY 1 RELAY 2 RELAY 3 1 2 3 4 5 6 7 8 9 10 11 12 Wiring Diagram Notes: Capacitor and resi...

Page 15 - ELECTRICAL SCHEMATIC

15 L1 (X) L2 (Y) FAN C TSTAT NO COOL DOWN TSTAT NC HIGH LIMIT POWER ON/OFF (I/O) SWITCH 2 POLE TFRMR 230Vp:24Vs C2 C1 +12V R1 R2 R3 TIMER BOARD SSR 1 SSR 2 SSR 3 HEATING ELEMENTS HEATING ELEMENTS HEATING ELEMENTS GND (E) Schematic Notes: Capacitor and resistor inside dashed box are used ONLY on ...