Telex EVID Ceiling Speaker Systems - Manuals

EVID™ Ceiling Series Systems (sold in pairs) Model Part No. Description C4.2 301258000 4" coaxial speaker with horn-loaded, Ti-coated tweeter C8.2 301261000 8" coaxial speaker with horn-loaded, Ti-coated tweeter C8.2LP 301318000 Same as C8.2 above except with low-profile backcan C8.2HC 30126...

The EV ID™ mounting system has beendesigned so that, if necessar y, the installationcan be done from beneath the ceiling. Insome cases with a suspended ceiling grid,however, it may be easier to access from boththe top and bottom of the ceiling tile duringthe installation process. Typical installatio...

Step 1: Cut the Hole (Figure 6) For suspended tile or sheetrock ceilings, cutout the hole either by tracing the cardboardtemplate or with a circular cutter set to theappropriate cutout size. If the wire has beenpre-installed, pull the wiring through thecutout hole. Step 2: Install C-Ring and/or Tile...

INSTALLATION NOTE: CONNECTORWIRING GUIDELINES The input connector’s 4 terminals are num-bered and marked on the connector. Pins 1 and2 are positive (+); pins 3 and 4 are negative (–).(Pin 1 is connected to Pin 2 and Pin 3 is con-nected to Pin 4 inside the speaker.) Pins 1 and4 are used as daisy-chai...

1. If plenum cable is used, slide the wiring through the strain relief fitting on the termi-nal cover plate (Figure 14). Hold the strainrelief fittings tight around the cable. Tightenthe strain relief screws first, then the hori-zontal screw. In the cases of insulatedspeaker wire and plenum cable, i...

INSTALLATION NOTE: MOUNTING TABS For each attachment screw, first turn onehalf-turn counterclockwise to release themounting tab from its guide. Step 6: Connect an AuxiliarySupport Line (Figure 18) Note the support ring on the back of thespeaker. The ring allows for connection to aindependent and sec...

If the speaker is installed in an area wherethe interior design requires a color match,these speakers are simple to paint. Thespeakers can accommodate almost any typeof latex or oil-based paint. The bezel/rimcan be painted before installation or af termounting into the ceiling. Painting Process Clea...

Selecting and PositioningCeiling Loudspeakers Several key criteria determine the type andquantity of ceiling speakers to employ in ajob. Speci fic EV ID™ Ceiling Series modelsaccommodate each job, depending on howthese criteria are speci fied.• Room size• Coverage density desired• Coverage angle spe...

tions that do not need the extended perform-ance of the larger models. Reverberant Rooms and High Ceilings Situations arise, however, in which con-trolled coverage is more desirable thanbroad dispersion. Ver y large live spacessuch as gymnasiums, convention centers,shopping mall atriums, and the lik...

Troubleshooting Table Problem Possible Causes Action No output Amplifier Make sure the amplifier channel is being fed an input signal (preferably via a “signal input” indicator on the amp). Check that the amplifier channel’s volume is turned up. Connect the speaker and cable, which had no output to ...

Uniform Limited Warranty Electro-Voice ® speakers and speaker systems are guaranteed against malfunction due todefects in materials or workmanship for aperiod of five (5) years from the date of orig-inal purchase. The Limited Warranty doesnot apply to burned voice coils or malfunc-tions such as cone...

Specification EVID C4.2 EVID C8.2 EVID C8.2LP EVID C8.2HC EVID C10.1 Dimensions 6.9" × 7.1" 10.0" × 10.6" 7.0"× 10.6" 11.9" × 12.6" 11.9" × 12.6" (depth x diam.) (176 × 181 mm) (255 × 270 mm) (190 × 255 mm) (303 × 320 mm) (303 × 320 mm) Bez el diameter 8.3"...

16 EVID™ Ceiling Series Installation and Operation Manual Notes