Tektronix VX4801 - Manuals
Tektronix VX4801 – Manual in PDF format online.
Manuals:
Manual Tektronix VX4801
Summary
WARRANTY Tektronix warrants that this product will be free from defects in materials and workmanship for a period of three(3) years from the date of shipment. If any such product proves defective during this warranty period, Tektronix,at its option, either will repair the defective product without c...
EC Declaration of Conformity We Tektronix Holland N.V.Marktweg 73A8444 AB HeerenveenThe Netherlands declare under sole responsibility that the VX4801 meets the intent of Directive 89/336/EEC for Electromagnetic Compatibility.Compliance was demonstrated to the following specifications as listed in th...
VX4801 Programmable Digital I/O Module iii General Safety Summary Review the following safety precautions to avoid injury and prevent damage tothis product or any products connected to it. Only qualified personnel should perform service procedures. While using this product, you may need to access ot...
General Safety Summary iv VX4801 Programmable Digital I/O Module Safety Terms and Symbols These terms may appear in this manual: WARNING. Warning statements identify conditions or practices that could result in injury or loss of life. CAUTION. Caution statements identify conditions or practices that...
VX4801 Programmable Digital I/O Module A–19 Appendix E: Performance Verification 123 This procedure verifies the performance of the VX4801 Programmable DigitalI/O Module. The test sequences may be performed in your current VXIbussystem if it meets the requirements described in Table 2. Also, it is n...
Appendix E: Performance Verification A–20 VX4801 Programmable Digital I/O Module NOTE . Commands to the VX4801 may be entered in upper or lower case. However, to avoid confusion between the alphanumeric characters; e.g. one (1)and L or zero( 0) and o, all commands are shown in the case which provide...
Appendix E: Performance Verification A–22 VX4801 Programmable Digital I/O Module VX4801 Under-Test Configuration In order to perform this procedure, the VX4801 under-test must be installed in anapproved VXIbus system. At a minimum, the system must contain the elementslisted in Table 2. Table 2: Elem...
Appendix E: Performance Verification VX4801 Programmable Digital I/O Module A–23 Test Record Photocopy the Test Record, and use it to record the performance verificationresults for your module. Table 4: VX4801 Test Record VX4801 Serial Number: Temperature and Relative Humidity: Date of Last Calibrat...
Appendix E: Performance Verification A–24 VX4801 Programmable Digital I/O Module Self Test The VX4801 includes a built-in self test function (BITE) which is automaticallyexecuted each time the power is turned on and when the Internal Self Test (S)command is issued. BITE uses internal routines and ci...
Appendix E: Performance Verification VX4801 Programmable Digital I/O Module A–25 NOTE . If you are using National Instruments NI-488.2 software you may wish to select the buffer 1 mode to allow more comfortable viewing of the ASCIIresponse. Just type buffer 1. 1. To verify the system configuration, ...
Appendix E: Performance Verification A–28 VX4801 Programmable Digital I/O Module 4. To verify the even byte data inputs and the odd byte data outputs, reset the VX4801 to its power-up state and then set its mode for the even bytes (0, 2,4) to be active low inputs, for the odd bytes (1, 3, 5) to be a...
Appendix E: Performance Verification VX4801 Programmable Digital I/O Module A–29 (Observe: response of 00FF00FF00FF) b. Repeat the above test, this time with the even bytes set as inputs and the odd bytes set as tri-stated outputs. Perform an input of all bytes andverify that the even bytes are in t...
Appendix E: Performance Verification VX4801 Programmable Digital I/O Module A–31 This test sequence verifies that data can be transferred to and from the VX4801using the four handshake signal lines Data Ready (DRD), Data Acknowledge(DAK), Ready for Data (RFD), and Data Available (DAV). NOTE . Typing...
Appendix E: Performance Verification A–32 VX4801 Programmable Digital I/O Module d. Set the Slave to initialize byte 2 with an Output Data value of 01 (asserts RFD to the VX4801) and verify that the VX4801 correspondinglyasserts DAV: (Observe: VX4801 DAV light on) e. Set the Slave to input bytes 1 a...
Tektronix Manuals
-
Tektronix SG 5010
Manual
-
Tektronix Z340LTA
Manual
-
Tektronix 7834
Manual
-
Tektronix 070-9180-01
Manual
-
Tektronix 11403A
Manual
-
Tektronix 550
Manual
-
Tektronix ps 501
Manual
-
Tektronix CSA 803A
Manual
-
Tektronix P6015
Manual
-
Tektronix 016-1249-00
Manual
-
Tektronix SG 505
Manual
-
Tektronix 016-1414-00
Manual
-
Tektronix AM700
Manual
-
Tektronix 016-1335-00
Manual
-
Tektronix 1705A
Manual
-
Tektronix 784A
Manual
-
Tektronix 2445
Manual
-
Tektronix TLA7XXX
Manual
-
Tektronix 524A
Manual
-
Tektronix 016-1341-00
Manual