Tanaka TPE-2501 - Manuals - manualsarea.com

Page 2 - Owner’s Manual; Before using this unit:; Read the operator’s manual carefully.; WARNING; The engine exhaust from this product; approaches you, stop the engine and cutting

www.tanaka-usa.com 1 [email protected] Owner’s Manual TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF Before using this unit: • Read the operator’s manual carefully. • Check that the cutting equipment is correctly assembled and adjusted. • Start the unit and check the carburetor adjustment. See “Maint...

Page 3 - Choke lever

www.tanaka-usa.com 2 [email protected] Owner’s Manual TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF Since this manual covers several models, there may be some difference between pictures and your unit. Use the instructions that apply to your unit. 1. What is What? 1. Fuel Cap 2. Throttle Trigger 3. ...

Page 5 - Throttle wire/stop cord

www.tanaka-usa.com 4 [email protected] Owner’s Manual TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF 3. Assembly procedures. Drive shaft to engine (Fig. 1 -1) Loosen tube locking bolt (1) about ten turns so that the bolt point will not obstruct drive shaft tube to be inserted. When inserting drive sh...

Page 6 - ) Before installation of blade, take off left hand

www.tanaka-usa.com 5 [email protected] Owner’s Manual TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF Installation of blade guard (Fig. 1-7) 1) Install blade guard (1) on gear case (4) temporarily by clamping with guard brackets (2) and screws (3). Then tighten as needed. 2) Line up the slot of guard ...

Page 7 - Fuel; Always use branded 89 octane unleaded gasoline.; Fueling; Always shut off the engine before refueling.

www.tanaka-usa.com 6 [email protected] Owner’s Manual TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF 4. Operating procedures. WARNING! This unit is equipped with a two-stroke engine. Always run the engine on fuel, which is mixed with oil. Provide good ventilation, when fueling or handling fuel. Fuel ...

Page 8 - and blade and remove it.

www.tanaka-usa.com 7 [email protected] Owner’s Manual TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF Starting (Fig. 2-2) CAUTION! Before starting, make sure the cutting attachment does not touch anything. 1. Set ignition switch (1) to ON position. *Push priming bulb (4) several times so that fuel flo...

Page 9 - AND SYSTEMS MAY BE PERFORMED BY ANY NONROAD ENGINE REPAIR

www.tanaka-usa.com 8 [email protected] Owner’s Manual TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF 5. Maintenance. MAINTENANCE, REPLACEMENT, OR RE PAIR OF THE EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY NONROAD ENGINE REPAIR ESTABLISHMENT OR INDIVIDUAL. Carburetor adjustment (Fig. ...

Page 10 - Spark Arrestor

www.tanaka-usa.com 9 [email protected] Owner’s Manual TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF Spark plug (Fig. 3-3) The spark plug condition is influenced by: • An incorrect carburetor setting. • Wrong fuel mixture (too much oil in the gasoline) • A dirty air filter. • Hard running conditions ...

Page 11 - Maintenance schedule

www.tanaka-usa.com 10 [email protected] Owner’s Manual TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF Maintenance schedule Below you will find some general maintenance instructions. For further information please contact your service dealer. Daily maintenance • Clean the exterior of the unit. • Check...

Page 12 - Engine Size

www.tanaka-usa.com 11 [email protected] Owner’s Manual TPE-2501,TPE-2510,TPE-270PF/PN,TPE-250PF 6. Specifications Model TPE-2501 TPE-250PF TPE-2510 TPE-270PF/PN Engine Size 24 ml (1.4 cu. in.) ! ! 26 ml (1.58 cu. in.) Carburetion System (Optional) Walbro Diaphragm (w/Priming Pump) ! ! ! Spark P...