Tanaka TPB-400GX - Manuals - manualsarea.com

Page 2 - Page 2; IMPORTANT; PLEASE READ THIS BEFORE USING THIS PRODUCT; Pregnant persons should not use this product.

Page 2 IMPORTANT PLEASE READ THIS BEFORE USING THIS PRODUCT READ THIS FIRST! WARNING This product does not conform to Federal Motor Vehicle Standards and is not intended for operation on public streets, roads, or highways. Serious injury or death can result from the unsafe operation of this product....

Page 3 - Page 3; Never ride on pedestrian sidewalks.

Page 3 SAFETY (Cont.) Never ride on pedestrian sidewalks. Being seen is very important. Brightly colored clothing and safety gear can increase visibility. Familiarize yourself with the powerboard. Take turns slowly and provide plenty of stopping distance. Ride very cautiously until you become famili...

Page 4 - Table of Contents; Idle Adjustment...........................................................................................8; Page 4

Table of Contents Getting to Know Your Tanaka Powerboard……………………………………………..5 Getting Started………………………………………………………………………………..6 Fueling……………………………………………………………………….6 Folding Handle Set-Up Instructions………………………………………6 Starting………………………………………………………………………7 Idle Adjustment……………………………………………………………………………….8 C...

Page 6 - Use Tanaka Perfect Mix; Page 6

GETTING STARTED Folding Handle Set-Up Instructions To unfold the powerboard, begin by pressing down on the FOLDING HANDLE with one hand (Fig. 3), while gently pulling up on the handlebars with the other (Fig. 4). Fully extend the handlebars to their upright position until you feel the mechanism lock...

Page 7 - Page 7

Starting Warning: Never attempt to start the engine if it is detached from the frame of the powerboard. If engine is started when detached, clutch components will come loose and can cause serious injury or death. Before starting, move at least 10 feet away from where you filled the tank. 1. Depress ...

Page 8 - Cleaning the Air Filter; Page 8

Idle Speed Adjustment (Fig. 9) When the idle speed is adjusted properly, the engine will run smoothly, without pressing the THROTTLE LEVER. If adjustment is required: 1. Start the engine. 2. Using a long, Philips head screwdriver gently close (clockwise) the T-screw until the Powerboard starts to mo...

Page 9 - Page 9

Riding Make sure that all of the bolts and screws are tightened. Put one foot on the deck of the powerboard. While pushing off with the other foot, gently squeeze the ACCELERATOR LEVER on the right side of the handlebars. The powerboard will begin to move on its own power. Control your speed by pres...

Page 11 - ADJUSTING THE HEAD UNIT; To adjust the head unit:; The head unit bearings are held in place by two 40mm; How tight should the belt be?

ADJUSTING THE HEAD UNIT The head unit will should come adjusted from the factory. However, riding on rough terrain and general use may cause the head unit to become loose over time. It may be necessary to adjust the head unit from time to time. To adjust the head unit: 1. Rotate the handle bar as fa...

Page 12 - MAINTENANCE SCHEDULE; Maintenance - Perform each time you ride your unit.

ADJUSTING THE BELTS (con’t) 1.The correct tension is achieved when the total up and down play of the small clutch belt is approximately ½” and the larger drive belt is approximately 1”. 2. Adjusting the belts: a. Turn the two belt tension bolts, located on the outside of the drive belt frame plates ...

Page 13 - Tanaka Limited Warranty Info; Engines; after delivery to the; VOID; part; Frame/Chassis Components; To; Tanaka c/o International

Tanaka Limited Warranty Info Engines Tanaka Kogyo Co., Ltd (“Tanaka”) hereby warrants products manufactured by it or sold by it to be free from defects in material or workmanship for a period of 180 days after delivery to the first consumer end user in a non commercial application. All components on...