Tanaka TBC-250PF/PFD - Manuals

Page 2 - www.tanaka-usa.com 1 [email protected]; Owner’s Manual; Before using this unit:; Read the operator’s manual carefully.; WARNING; The engine exhaust from this product; stop the engine and cutting

www.tanaka-usa.com 1 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D Before using this unit: • Read the operator’s manual carefully. • Check that the cutting equipment is correctly assembled and adjusted. • ...

Page 4 - instructions that apply to your unit.

www.tanaka-usa.com 3 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D 1. What is What? Since this manual coves several models, there may be some difference between pictures and your unit. Use the instructions...

Page 6 - Assembly procedures

www.tanaka-usa.com 5 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D 3. Assembly procedures Drive shaft to engine (Fig. 1 -1) Loosen tube locking bolt (1) about ten turns so that the bolt point will not obst...

Page 7 - Cover throttle wire and stop cords together with protective tube

www.tanaka-usa.com 6 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D Throttle wire/stop cord Remove the air cleaner cover. (Fig. 1-4) Connect stop cords. (Fig. 1 -5) Cover throttle wire and stop cords togeth...

Page 9 - Installation of cutting blade; with the box wrench.; Installation of the cutting head; They can break off and become a dangerous projectile.

www.tanaka-usa.com 8 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D Installation of cutting blade (Fig. 1-10, 10B) (If so equipped) When installing a cutting blade, make sure the blade is not cracked or...

Page 10 - Operating procedures

www.tanaka-usa.com 9 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D 4. Operating procedures Fuel (Fig. 2-1) WARNING! The trimmer is equipped with a two-stroke engine. Always run the engine on fuel, which is...

Page 11 - before subjecting it to any load.

www.tanaka-usa.com 10 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D CAUTION! Before starting, make sure the cutting attachment does not touch anything. Starting (Fig. 2-2, 2B) 1. Set ignition switch (1) to...

Page 12 - where it is difficult to see the material to be cut.

www.tanaka-usa.com 11 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D Cutting (Fig. 2-4, 4B, 4C, 4D) • When cutting, operate engine at over 6500 rpm. Extended use at a low rpm will wear the clutch prematurel...

Page 13 - OF THE EMISSION CONTROL DEVICES AND; The air filter must be cleaned from dust and dirt in order to avoid:

www.tanaka-usa.com 12 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D 5. Maintenance MAINTENANCE, REPLACEMENT, OR REPAIR OF THE EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY NONROAD ENGINE REP...

Page 14 - element out of holder assembly. Replace filter if it appears to be

www.tanaka-usa.com 13 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D Drain all fuel from fuel tank and pull fuel filter line from tank. Pull filter element out of holder assembly. Replace filter if it appea...

Page 15 - Do not completely fill the transmission.

www.tanaka-usa.com 14 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D Angle transmission (Fig. 3-5B) Check the gear case grease level about every 50 hours of operation by removing the grease filler plug on t...

Page 19 - The following standards have been taken into consideration

www.tanaka-usa.com 18 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D Declaration of conformity D6claration de conformit6 Dichiarazione di conformita Konformitiitserkliirung Declaraci6n de conformidad Konfor...

Page 20 - IMPORTANT NOTICE; THIS INFORMATION IS FOR THE US AND CANADIAN MARKETS ONLY.; uncertain about any aspect of blade use on your Tanaka unit.

www.tanaka-usa.com 19 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D IMPORTANT NOTICE THIS INFORMATION IS FOR THE US AND CANADIAN MARKETS ONLY. • To reduce the risk of injury from loss of control, never use...

Page 21 - and utilizes centrifugal; Cutting Attachments for Tanaka Trimmers and Brushcutters

www.tanaka-usa.com 20 [email protected] Owner’s Manual TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PFD TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D,TBC-340PF/D (1) Fixed line commercial cutting heads offer excellent durability and light weight. Great for commercial use. (2) Tanaka Brain fully aut...