Swisher ZT2350 - Manuals

OPERATING YOUR NEW ZERO TURN RIDER MOWER CONTROLS • OPERATOR PRESENCE SYSTEM: This mower is equipped with an operator’s presence system. Any attempt to leave the seated position with the engine running, without first disengaging the PTO switch will cause the engine to shut off. Never get off the mow...

STARTING MOWER • TO START: Position steering handles outward to neutral locked position. Engage parking brake. Extend throttle to full choke position. Start ignition and slide throttle lever back to full throttle position. Allow engine to warm up for 1 minute. Release parking brake. The ZT2350 has a...

MAINTENANCE SCHEDULE INSPECT BEFORE EACH USE • Loose fasteners: Be sure all fasteners are at proper torque. Especially guards and blades. • Parking brake: If brake does not keep unit from rolling, brake must be adjusted or repaired. • Tires: Always check and maintain proper tire pressure (See tire s...

INSPECT EVERY 25 HOURS • Lubrication: Grease all pivot points with a high temp grease. • Battery, check and clean: Keep battery terminals clean and tight. Periodic charging will extend its life. Clean terminals with a wire brush and coat with a petroleum jelly. • Change engine oil and filter: Use on...

SERVICE / ADJUSTMENTS TRACKING Adjustments to the unit may need to be made if the unit does not track in a straight line. The primary reason for the unit not tracking straight is incorrect or unbalanced tire pressure. Before making any adjustments first check and adjust the tire pressure. DO NOT EXC...

LEVELING THE MOWER DECK 1. Position unit on a smooth level surface. 2. For side to side leveling, measure the distance from the floor to the bottom edge at the rear of the deck. The measurement should be equal within 1/16 inch side to side. Adjustment can be made by loosening locking nut on rear eye...

BELTS Clutch drive belt replacement 1. Remove belt covers.2. Disconnect tension idler from tension bracket. 3. Remove belt from mower pulley and electric clutch. 4. Install new belt onto electric clutch and mower pulley and check for proper routingand clearance. 5. Reconnect idler tension bolt to te...

ENGINE SETUP 16 Item # Description Part # 1 23 HP B&S Engine (50" Mower) N/A 2 5/16-18 Serrated Flange Nut NB170 3 Spacer Engine Pulley BB105SL 4 Motor Pulley 3" 3753 5 1/4 X 1/2 Key Stock 4258 6 Engine Pulley Spacer Short .687 689S 7 Electric Clutch Drop Pulley 688ECDP Electric Clutch (...

17 Description Part # 5/16-18 X 4 HCC GR5 ZP NB513 5/16-18 X 2 3/4 HCCGR2ZP NB106 5/16 SAE Washer NB275 5/16-18 Nyloc Nut NB181 PARTS NOT SHOWN (Zero Turn Rider Trans Mounting Hardware) Item # Description Part # 1 Wire Link For Idler Arm BRS6H 2 Clutch Rod Spring 682S 3 5/16-18 Serrated Flange Nut N...

FRAME for 50” Mower Item # Description Part # 1 Beverage Retainer 3643TK 2 Fender-Right 3012TK Fender-Left 3011TK 3 Fender Mount 5142TK 4 Battery Box 3696TK 5 5/16-18 X 3/4 Serr Flg Bolt NB596 6 Transmission Mount 3835TK 7 Upper Motor Base 3777TK 8 5/16-18 Serrated Flange Nut NB170 9 Rear Cover 3711...

22 Item # Description Part # 23 Height Adjust Indicator 3671TK Height Adjust Indicator Decal OD99151 24 Height Adjust Indicator Bracket 3845TK 25 8-32 Nut NB201 25B 8-32 Machine Screw NB689 26 5/16-18 X 2 GR5 Bolt NB507 27 5/16-18 2 way Lock Nut NB558 28 5/16-18 Nyloc Nut NB181 HEIGHT ADJUST INDICAT...

Item # Description Part # 1 3/4-16 2 Way Lock Nut NB175 2 1.5x.761x.098x.134 Belleville Washer AS155 3 Blade Pulley 4.5" B4104TK 4 Washer For Blade Driver NB179 5 Blade Bearing B98 6 Blade Shaft 4.25" 9076 7 Bearing Housing B99ECTK 8 17.5" Blade for 50" Mower 5059 9 Blade Driver Assy...

DECK IDLER 17 SEE DETAIL Page 16 SEE DETAIL THIS PAGE 7 14 19 3 1 4 18 20 2 15 14 13 4 12 16 10 9 8 Item # Description Part # 1 Grass Chute Weldment 3773TK 2 5/16-18 X 3/4 Serr Flg Bolt NB596 3 Grass Chute Mount 6030TK 4 3/8-16 Nyloc Nut ZY NB182 5 3/8-16 Nylok Nut Jam NB207 6 3/8 USS Washer NB271 7...

CORRECTION CAUSE SYMPTOM 1. CHECK AND ADJUST TIRE PRESSURE 2. SEE TRACKING ADJUSTMENT IN SERVICE SECTION 1. IMPROPER AIR PRESSURE 2. TRACKING ADJUSTMENTS OUT OF ADJUSTMENT UNIT DOES NOT TRACK STRAIGHT 1. MOVE LEVERS INTO POSITION 2. PUSH PTO SWITCH IN 3. SEE START UP IN OPERATION SECTION 4. WAIT SEV...

OWNER’S MANUAL MODEL NO. ZT2350 Each mower has its own model number. Each engine has its own model number. The model number for the mower will be found under the seat. The model number for the engine will be found on the top of the blower fan housing.All mower parts listed herein may be ordered dire...