Page 6 - SAFETY AND OPERATIONAL DECALS; WARNING; SERIOUS INJURY OR DEATH CAN OCCUR; DANGER; SPINNING BLADE; KEEP CLEAR
4 SAFETY AND OPERATIONAL DECALS Replace decal immediately if damaged. Order by part number from Swisher Mower and Machine Co. Inc. WARNING ! SERIOUS INJURY OR DEATH CAN OCCUR - MOVING PARTS - SHARP BLADES - THROWN OBJECTS - POSSIBILITY OF ROLL OVER - • GO UP AND DOWN SLOPES, NOT ACROSS.• AVOID SUDDE...
Page 8 - IMPORTANT! - READ THIS MANUAL BEFORE OPERATING MOWER; ASSEMBLY
6 IMPORTANT! - READ THIS MANUAL BEFORE OPERATING MOWER Be sure to check your new Swisher Riding Mower for shipping damage before beginning assembly. These parts are packaged with your new mower. The following tools are needed for assembling your new Swisher Riding Mower: - Steering Wheel - includes ...
Page 10 - BECOMING FAMILIAR WITH YOUR NEW SWISHER MOWER
Check fuel and oil levels. Make sure the Drive Control and Blade Clutch Levers are pulled back and disengaged. Make sure your foot is off the pedal. Once engine is started, become familiar with the steering and maneuvering of the mower before engaging the blades. The Lock Pin Lever (TR148L) should a...
Page 12 - MOWER MAINTENANCE
NEVER ADD GASOLINE TO A HOT EN-GINE - ALLOW ENGINE TO COOL BE-FORE ADDING GASOLINE. 10 MOWER MAINTENANCE Make sure your mower is in safe working condition by keeping the following guidelines in mind every time you useyour mower. Keep mower in good operating condition and keep safety guards, shields ...
Page 13 - ADJUSTMENTS AND ROUTINE SERVICING; WARNING - ALWAYS STOP ENGINE AND DISCONNECT SPARK PLUG WIRE
11 ADJUSTMENTS AND ROUTINE SERVICING WARNING - ALWAYS STOP ENGINE AND DISCONNECT SPARK PLUG WIRE AND BATTERY BEFORE MAKING ADJUSTMENTS OR SERVICING MOWER! CUTTING HEIGHT ADJUSTMENT: • Turn Height Adjustment Crank (H7N) Clockwise to raise the blade Counter-Clockwise to lower the blade. BLADE SHARPENI...
Page 14 - STORING YOUR MOWER
12 Disconnect Spark Plug Wire Drain the fuel. Drain the oil and refill the crankcase with clean oil. Clean your mower. Brush off matted clippings and caked-on dirt. Use a wire brush to clean the underside of lawn mower. Use a cloth to wipe away debris from the upper deck. If available, use a...
Page 16 - MULCHING MOWERS; MOWERS
14 MULCHING MOWERS (Models ending in M) To adjust your mower for mulching, make sure your discharge chute is closed so grass clippings cannot escape and may be cut several times. To close the chute, slide the chute TOWARD the mowing deck and tighten the knob. Your Swisher Mulching Mower has the bu...
Page 17 - BRUSH ADJUSTMENTS; BAG AND BRUSH REPLACEMENT
15 EMPTYING THE COLLECTOR - BE SURE TO DIS-ENGAGE BLADES AND STOP ENGINE BEFOREEMPTYING THE COLLECTOR! To empty the collector, pull the rear support bar of the collector up toward the mower. The pile of clippings or leaves will fall almost directly below the collector. COMPOSTING For those intereste...
Page 18 - Swisher Zero Turn Rider
16 Swisher Zero Turn Rider 01 02 03 04 06 07 08 05 09 10 11
Page 19 - Belt housing with motor base removed
17 Belt housing with motor base removed 12 13 14 15 16 17 18 18 19 22 21 20 23
Page 20 - Two speed pulley assembly
18 Two speed pulley assembly 37 24 25 26 27 28 29 30 31 32 33 34 36 35
Page 21 - Variable Speed Pulley Assembly
19 41 40 38 39 43 42 Variable Speed Pulley Assembly
Page 28 - Replacement Parts
26 Replacement Parts Hood AZ154 Grommet - large AZ154GL Grommet - small AZ154GS Hood trim AS116 Steering/fuel port trim AS117 Mounting bolt AZ154B Acorn nuts FR154N Gas cap AZ154C Gas tank AZ154T Tank mount AZ154TM Tank straps AS013 Fuel line FLH27 Steering wheel AZ120 Bushing AZ120B Set screw - sho...
Page 29 - Replacement Parts
27 Replacement Parts Lower shroud AZ154L Washer/nut AZ154LWN Front wheel/tire/bearing Chain guard T162 Traction Assembly A124W Flanged bushing (upper/lower) A124B Steering gear pin A124P Steering gear A124S Gear case A136W Flathead socket screws A140 Worm shaft T135 Gasket T136G Gear case lid T136L ...