Supermicro SSE-G48-TG4 - Manuals

Page 4 - Contents

Release: 1.0c 4 / 27 Supermicro Switch Web GUI Quick Configuration Guide Contents 1 Introduction ................................................................................................................. 5 2 Basic Configurations .....................................................

Page 5 - Introduction

Release: 1.0c 5 / 27 Supermicro Switch Web GUI Quick Configuration Guide 1 Introduction This document is designed to provide Supermicro switch users with the information required to configure the basic functionalities on the switch through its Web graphical user interface (GUI). Superm...

Page 6 - Basic Configurations

Release: 1.0c 6 / 27 Supermicro Switch Web GUI Quick Configuration Guide 2 Basic Configurations 2.1 Login Page When you type the switch IP address into the browser, the following Login page appears. Fig 1: Login page Enter the User Name and Password and click on the Login button. This ...

Page 10 - Management IP Address; Switch

Release: 1.0c 10 / 27 Supermicro Switch Web GUI Quick Configuration Guide 2.3 Management IP Address Note : The default management IP address for all Supermicro switch products is: 192.168.100.102 . Switch Management IP Interface SSE-G24-TG4 SSE-G48-TG4 The management IP address is conf...

Page 13 - Interface MTU and Jumbo Frames

Release: 1.0c 13 / 27 Supermicro Switch Web GUI Quick Configuration Guide 2.5 Interface MTU and Jumbo Frames The interface MTU can be changed in Layer2 Mgmt  Port Manager  Basic Settings page. The default MTU is 1500 bytes. The maximum MTU supported is 9202. The Supermicro switch MTU...

Page 16 - Tracking Uplink Failure; Link tracking can be configured from the

Release: 1.0c 16 / 27 Supermicro Switch Web GUI Quick Configuration Guide Note: 1. Do not use the same switch ID for multiple switches on the stack. 2. All switches in the stack can only be configured through the master switch. 3. Make sure all stacked switches run the same version of ...

Page 18 - Saving Configurations

Release: 1.0c 18 / 27 Supermicro Switch Web GUI Quick Configuration Guide 2.9 Saving Configurations Switch configurations can be saved on the System Mgmt  File Management page. You can save a currently running switch configuration in one of three ways.  Save Startup Config – This opt...

Page 19 - Upgrading Firmware

Release: 1.0c 19 / 27 Supermicro Switch Web GUI Quick Configuration Guide 2.10 Upgrading Firmware Switch firmware can be upgraded in the System Mgmt  Firmware Upgrade page. Flash Area – The default selection is Normal to upgrade firmware in normal flash area. To upgrade firmware in th...

Page 20 - Resetting to Factory Defaults

Release: 1.0c 20 / 27 Supermicro Switch Web GUI Quick Configuration Guide 2.11 Resetting to Factory Defaults Supermicro switches can be reset to factory defaults in the System Mgmt  System Settings page. This page has a button that you can press to allow a “Reset To Factory Defaults”....

Page 21 - VLAN Configurations; VLANs can be configured in

Release: 1.0c 21 / 27 Supermicro Switch Web GUI Quick Configuration Guide 3 VLAN Configurations The SSE-G24-TG4, SSE-G48-TG4, SBM-GEM-X2C, SBM-GEM-X2C+ and SBM-GEM-X3S+ switches support 1024 static VLANs. The SSE-X24S, SSE-X24SR, SSE-X3348S, SSE-X3348SR, SSE-X3348T, SSE-X3348TR and SBM...

Page 23 - Enabling LA Status

Release: 1.0c 23 / 27 Supermicro Switch Web GUI Quick Configuration Guide 4 Link Aggregation (LA) Link Aggregation (LA) is a method of combining multiple parallel physical connections into a single logical connection(trunk), thus allowing increased bandwidth for a particular network pa...

Page 26 - Associating a Port Channel with Ports

Release: 1.0c 26 / 27 Supermicro Switch Web GUI Quick Configuration Guide 4.3 Associating a Port Channel with Ports Once a port channel is created in the port channel page, it can be associated with the required physical ports. This can be done in the Layer2 Mgmt  LA  Port Settings p...

Page 27 - Configuring Port Channel Parameters

Release: 1.0c 27 / 27 Supermicro Switch Web GUI Quick Configuration Guide 4.4 Configuring Port Channel Parameters Once a port channel is created and associated with the required ports, you can configure the port channel parameters. If necessary configure the MTU of the port channel in ...