Superior NMC004-TD - Manuals

Page 2 - INTRODUCTION; TABLE OF CONTENTS; Variable Flame Adjustment; GENERAL INFORMATION; Installation and repair should be per-

2 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. These appliances are designed to operateon natural or propane gas only. On Millivolt models the Input of the appliancecan be varied from 13,500 to 17,500 BTU/HR.On Electronic models the input is fixed at17,500 BTU/HR. CONGRATULATIONS! In selecting t...

Page 3 - Gas Controls/Control Compartment Access; Refer to; Piezo Ignitor; Sit and Honeywell Millivolt Gas Valve Showing

3 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 1 Millivolt Appliances - To light millivolt appliances refer to the detailedlighting instructions found in both English andFrench on pages 12 and 13 of these instruc- tions respectively. Millivolt appliance lighting instructions may also be f...

Page 4 - Homeowner must contact a; Honeywell Millivolt Gas Valve; Figure 4; SIT Millivolt Gas Valve; Figure 2

4 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. CAUTION: DO NOT ATTEMPT TO TOUCH THEFRONT ENCLOSURE GLASS WITH YOURHANDS WHILE THE FIREPLACE IS IN USE. Variable Flame Height Adjustment( Millivolt Appliances only) 1. All Millivolt appliances are equipped with a variable gas control valve. Flame he...

Page 5 - Maintenance Schedule

5 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Periodically (After the Burning Season) Maintenance Task Accomplishing Person Procedure Cleaning Firebox Interior Check Flame Patterns and Flame Height Checking Vent System Cleaning Front Glass Enclosure Panel Homeowner Homeowner Homeowner Homeowner...

Page 6 - Burner Adjustments

6 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Refer to Figure 5 and remove the front glass enclosure panel as follows : 1. Remove the top louver or radiant panel. 2. Open the hinged drop-down control com- partment panel. Flame Appearance and Sooting Proper flame appearance is a matter of taste....

Page 7 - Log Placement; Figure 8; . Insert the alignment hole of the left twig over; Glowing Ember Placement; Set the rear log on the raised bracket at the; Figure 7

7 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Log Placement Figure 8 3 . Insert the alignment hole of the left twig over the front log's left pin. Rotate the left twig until itjust touches the edge of the ember bed bracket. 4 . Insert the alignment hole of the right twig over the front log's ri...

Page 8 - Electronic Appliance Checkout; WIRING DIAGRAM; SIT and Honeywell Millivolt Appliance Checkout; The top; Figure 10 - Honeywell; for Honeywell; Figure 9; SIT MILLIVOLT

8 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Electronic Appliance Checkout To light the burner, turn ‘ON’ the optionalremote wall switch and turn the gas controlswitch to the “ON” position. Ensure the ignitorlights the pilot. The pilot flame should engulfthe flame rod as shown in Figure 11 . F...

Page 9 - The model number of the appliance.; ACCESSORY COMPONENTS

9 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. WARRANTY Your gas appliance is covered by a limited twentyyear warranty. You will find a copy of the war-ranty accompanying this manual. Please readthe warranty to be familiar with its coverage. Retain this manual. File it with your other docu-ments...

Page 12 - LIGHTING INSTRUCTIONS – HONEYWELL AND SIT MILLIVOLT GAS VALVE; FOR YOUR SAFETY READ BEFORE LIGHTING; HONEYWELL; SIT

12 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. LIGHTING INSTRUCTIONS – HONEYWELL AND SIT MILLIVOLT GAS VALVE WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSIONMAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. FOR YOUR SAFETY READ BEFORE LIGHTING A. ...

Page 13 - INSTRUCTIONS D’ALLUMAGE – VANNE GAZ MILLIVOLT HONEYWELL ET SIT; INSTRUCTIONS D'ALLUMAGE; VANNE GAZ

13 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. INSTRUCTIONS D’ALLUMAGE – VANNE GAZ MILLIVOLT HONEYWELL ET SIT INSTRUCTIONS D'ALLUMAGE 8. Enfoncez le bouton de réglage jusqu’au fond et gardez-le enfoncé.Allumez immédiatement la veilleuse en déclenchant l’allume-gaz àétincelle (en poussant le bou...

Page 14 - LIGHTING INSTRUCTIONS — ELECTRONIC; TO TURN OFF GAS TO APPLIANCE; Front View

14 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSIONMAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. A. When lighting the appliance, follow these instructionsexactly. B. BEFORE OPERATING smell all around...

Page 15 - INSTRUCTIONS D’ALLUMAGE — ELECTRONIC; INSTRUCTIONS D’ALLUMAGE; POUR ÉTEINDRE L’APPAREIL; POUR FERMER LE GAZ QUI ALIMENTE L’APPAREIL; Interrupteur; Vue de face

15 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. INSTRUCTIONS D’ALLUMAGE — ELECTRONIC INSTRUCTIONS D’ALLUMAGE POUR VOTRE SÉCURITÉ, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE A. Lorsque vous allumez l’appareil, suivez exactement ces in-structions. B. AVANT L’ALLUMAGE: Assurez-vous que vous ne détecte...

Page 16 - TROUBLESHOOTING THE MILLIVOLT GAS CONTROL SYSTEM; CORRECTIVE ACTION

16 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. TROUBLESHOOTING THE MILLIVOLT GAS CONTROL SYSTEM 1. Spark ignitor will not lightpilot after repeatedtriggering of ignitor button. 2. Pilot will not stay lit aftercarefully following thelighting instructions. 3. Pilot burning, no gas toburner, Valve...

Page 17 - TROUBLESHOOTING THE ELECTRONIC IGNITION SYSTEM; SYMPTOM

17 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. TROUBLESHOOTING THE ELECTRONIC IGNITION SYSTEM SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION See Below. Disconnect the two black wires from the wire nuts. Test switch(s) forcontinuity with a multimeter. If continuity is not indicated, switch(s) isdefec...

Page 19 - REPLACEMENT PARTS

19 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. REPLACEMENT PARTS 9 4 1 2 5 14 6 3 2 11 10 13 8 15 7 41 40 21 43 23 22 24 42 26 25 30 31 32 33 34 35 36 27 37 20 12 44 16