Sun Microsystems Sun Fire V100 - Manuals

Figures vii Figures FIGURE 1-1 The Sun Fire V100 server 2 FIGURE 2-1 Cable Management Bracket 9 FIGURE 2-2 Positioning the Slide Mounts for a Sun StorEdge 72-Inch Tall Rack 10 FIGURE 2-3 Positioning the Slide Mounts for a Standard 19-Inch Wide Rack 10 FIGURE 2-4 Fastening the Slide Mounts to a Sun S...

Tables ix Tables TABLE 1-1 Contents of the Ship Kit 3 TABLE 1-2 Customer Installable Hardware 4 TABLE 2-1 19-inch Rackmounting Kit 8 TABLE 3-1 Server Serial Ports 20 TABLE 3-2 Settings for Connecting to the Serial A/LOM or Serial B Port 21 TABLE 3-3 Serial Adapters 22 TABLE 3-4 Pin Crossovers in the...

xi Preface The Sun Fire™ V100 Server User ’s Guide describes how to install, manage, andmaintain the Sun Fire V100 server. The manual is intended for system administratorswho have experience in setting up networked Solaris TM servers. How This Book Is Organized Part I Installation and Configuration ...

xii Sun Fire V100 Server User’s Guide • December 2001 Part III Maintenance and Troubleshooting Chapter 7 provides information about the fault and power indicators and explainshow to identify a faulty system in a rack. Chapter 8 describes how to swap system configuration cards and how to open theSun ...

Preface xiii Typographic Conventions Shell Prompts Typeface Meaning Examples AaBbCc123 The names of commands, files,and directories; on-screencomputer output Edit your .login file. Use ls -a to list all files. % You have mail . AaBbCc123 What you type, whencontrasted with on-screencomputer output % ...

xiv Sun Fire V100 Server User’s Guide • December 2001 Accessing Sun Documentation Online A broad selection of Sun system documentation is located at: http://www.sun.com/products-n-solutions/hardware/docs A complete set of Solaris documentation and many other titles are located at: http://docs.sun.co...

Preface xv ■ Follow all cautions and instructions marked on the equipment. ■ Never push objects of any kind through openings in the equipment. Dangerousvoltages may be present. Conductive foreign objects can produce a short circuitthat could cause fire, electric shock, or damage to your equipment. S...

2 Sun Fire V100 Server User’s Guide • December 2001 Overview of the Sun Fire V100 Server The Sun Fire V100 server is a single-processor server in a one rack unit (1 RU)chassis. It is designed to maximize the density of high-performance Solaris servers ina rack. FIGURE 1-1 The Sun Fire V100 server Th...

Chapter 1 Introducing the Sun Fire V100 Server 5 Installation Quick Start Task See in the Sun Fire V100 Server User’s Guide 1 Install the Hardware Mount in the rack. “Installing the Sun Fire V100 Server Into a Rack”on page 7 Connect the cables. “Connecting the Cables” on page 17 Set up a console con...

8 Sun Fire V100 Server User’s Guide • December 2001 Choosing Between a Rack and a Cabinet The Sun Fire V100 server can be installed in either a rack or a cabinet. Factors thatmight influence your decision include: ■ SecurityIf other people have access to the room in which your servers are located, y...

Chapter 2 Installing the Sun Fire V100 Server Into a Rack 9 A bracket is provided to aid cable management at the back of the server (see FIGURE 2-1 ). Use zip ties to secure the cables to the cable management bracket and hold them in place. FIGURE 2-1 Cable Management Bracket ▼ To Assemble the Slide...

Chapter 2 Installing the Sun Fire V100 Server Into a Rack 11 5. Move the brackets so that the studs are in suitable slots and tighten the nuts. 6. Fasten the mounting slides to the rack using the screws supplied. For the Sun StorEdge 72-inch rack, refer to FIGURE 2-4 and FIGURE 2-5 . Leave the screw...

Chapter 2 Installing the Sun Fire V100 Server Into a Rack 15 8. Align the thumbscrews on the sides of the server with the slide mounts in the rack (see FIGURE 2-8 ). If necessary, readjust the slide mounts to align the server properly. The thumbscrewsneed to be finger-tight. FIGURE 2-8 Adjusting the...

16 Sun Fire V100 Server User’s Guide • December 2001 FIGURE 2-9 Fitting the Cable Management Bracket to a Sun StorEdge or a Standard 19-Inch Rack Tips for Using a Sun StorEdge 72-inch Rack ■ For maximum stability, fill the rack from the bottom up and at the top leave atleast four rack units empty. ■...

Chapter 2 Installing the Sun Fire V100 Server Into a Rack 17 ■ 1 RU (part number: 330-2610-01) ■ 2 RU (part number: 330-2611-01) ■ 3 RU (part number: 330-2613-01) ■ 4 RU (part number: 330-2614-01) ■ 5 RU (part number: 330-2615-01) ■ Position your racks so that the warm air exhaust from one rack does...

18 Sun Fire V100 Server User’s Guide • December 2001 2. Connect a serial device. For more information, see “Setting Up a Console Connection to the Server” onpage 20. If you want to use the server ’s Lights Out Management (LOM) facilities, use the portlabeled Serial A/LOM to make your serial connecti...

19 C H A P T E R 3 Communicating With the Server This chapter provides information on setting up a console connection to a Sun FireV100 server using a variety of devices. The information is contained in the followingsections: ■ “Setting Up a Console Connection to the Server” on page 20 ■ “Connecting...

Chapter 3 Communicating With the Server 21 FIGURE 3-1 Serial Port Pins 1 to 8 Serial Connection Settings The settings you need to use for a serial connection are listed in TABLE 3-2 . If you need to perform binary data transfers (that is, transfers of anything more thansimple ASCII character streams...

22 Sun Fire V100 User’s Guide • December 2001 Serial Adapters Depending on the type of device you use to connect to the server, you could need touse either a DB-25 or DB-9 serial adapter. TABLE 3-3 describes which type to use, and the following sections describe the crossovers each adapter performs....

Chapter 3 Communicating With the Server 23 ▼ To Use the DB-25 Adapter 1. Insert one end of the standard RJ-45 patch cable supplied with the Sun Fire V100 server into one of the server ’s serial ports. 2. Insert the other end of the RJ-45 patch cable into the supplied DB-25 adapter. 3. Attach the ada...

24 Sun Fire V100 User’s Guide • December 2001 ■ RJ-45 to RJ-45 patch cable Both are supplied with the Sun Fire V100 server. ▼ To Connect to the Server Using a SunWorkstation 1. Connect to the server using the RJ-45 patch cable and DB-25 adapter as described in “To Use the DB-25 Adapter” on page 23. ...

Chapter 3 Communicating With the Server 25 3. Make the setting changes shown below. The lom> prompt appears. For information about how to power on and configure the server, go to “PoweringOn and Configuring the Server” on page 34. Connecting to the Server Using aTerminal Server The pinouts for th...

26 Sun Fire V100 User’s Guide • December 2001 ■ Connect the breakout cable directly to the Sun Fire V100 server. ■ Connect the breakout cable to a patch panel and use the straight-through patchcable (supplied by Sun) to connect the patch panel to the server. Connecting to Other Terminal Servers For ...

Chapter 3 Communicating With the Server 27 For example, for a Sun Fire V100 server connected to port 10000 on a terminal serverwhose IP address is 192.20.30.10, you would type: Connecting to the Server Using a SystemRunning Microsoft Windows If you want to configure and operate a Sun Fire V100 serve...

28 Sun Fire V100 User’s Guide • December 2001 c. Click OK. 6. In the Connect To window: a. Click Edit. b. Click Connect Using. c. In the drop-down menu, click Direct to COM1. Note – If you connected the DB-9 adaptor to a port other than COM1 on your PC or laptop in Step 3, choose the appropriate opt...

Chapter 3 Communicating With the Server 29 Connecting to the Server Using aHandheld Device The Sun Fire V100 server can be configured from a handheld device that usesPalmOS 2.0 or later, as long as you have VT100 terminal emulation softwareinstalled on the device and the correct hardware with which ...

30 Sun Fire V100 User’s Guide • December 2001 3. Choose Menu > Options > Communications and make the following settings. This ensures correct communication with the server. 4. Choose Menu > Options > Terminal and make the following settings: 5. Click On. This starts the software’s online...

Chapter 3 Communicating With the Server 31 The following sections give some additional information that may make using thehandheld device’s terminal emulator easier. Using the Arrow Keys The arrow keys available on the PalmOS device do not work with a Sun Fire V100server. To work around this problem...

Chapter 4 Powering On and Configuring the Sun Fire V100 Server 35 1. Connect the server to the power supply but do not power it on. 2. Set up a serial connection to the Serial A/LOM port and also a connection to at least one Ethernet hub (as described in Chapter 3). 3. At the console lom> prompt,...

Chapter 4 Powering On and Configuring the Sun Fire V100 Server 37 17. At the system you are setting up, follow the prompts to provide time and date information. 18. When prompted, give a password (if any) for users logging in as root. The system will boot when you have provided it with the informati...

38 Sun Fire V100 Server User’s Guide • December 2001 ● If you are at the lom> prompt, go to the ok prompt by typing: 1. Boot the server into the Solaris environment by typing: 2. At the Solaris prompt, type: 3. When prompted to confirm that you want to create a “blank” server, type y . 4. When th...

Chapter 4 Powering On and Configuring the Sun Fire V100 Server 39 Using the Power (On/Standby) Switch Caution – The power switch on the back panel of the Sun Fire V100 server is not an On/Off switch, it is an On/Standby switch. It does not isolate the equipment. The power (On/Standby) switch is a ro...

43 C H A P T E R 5 Managing the Sun Fire V100 ServerFrom the lom> Prompt This chapter introduces the Lights-Out Management (LOM) facilities available forthe Sun Fire V100 server and describes how to use the /usr/sbin/lom utility, which provides a user interface to the device. The chapter contains...

44 Sun Fire V100 Server User’s Guide • December 2001 LOM commands enable you to: ■ Power the server on or to standby mode. ■ Monitor the server ’s temperature and the status of its power supply, fans, internalvoltage rails, fault LED, and alarms, even when the server is in standby mode. ■ Turn a Fau...

Chapter 5 Managing the Sun Fire V100 Server From the lom> Prompt 45 Powering On or Resetting the ServerFrom the LOM Shell Note – When a Sun Fire V100 server is connected to a power supply, it is always either fully powered on or in standby mode. To remove power entirely from theserver you must di...

46 Sun Fire V100 Server User’s Guide • December 2001 ▼ To Display the lom> Prompt ● To display the lom> prompt, type the following LOM escape sequence: When you type the LOM escape sequence, the LOM device takes control of the SerialA/LOM port and the lom> prompt appears on your terminal sc...

Chapter 5 Managing the Sun Fire V100 Server From the lom> Prompt 47 ▼ To Reset the Server ● To reset the server, type: ● To perform a limited reset affecting the processor only, type: The -x option generates the equivalent of an externally initiated reset (XIR) of the server. You must have r -lev...

48 Sun Fire V100 Server User’s Guide • December 2001 This command enables you to dictate the behavior of the server after a reset. Itsfunctionality is identical to that available on Sun keyboards with the Stop keycombinations. (However, the bootmode command is provided because the Stop key combinati...

50 Sun Fire V100 Server User’s Guide • December 2001 ▼ To Check How Long the Server Has BeenRunning ● To find out how much time has elapsed since the last boot, type: or: ▼ To Check the Current Status of All Components ● To see the current status of all the components monitored by the LOM device,typ...

Chapter 5 Managing the Sun Fire V100 Server From the lom> Prompt 51 Viewing the LOM Event Log The eventlog command reports the last 10 events. The loghistory command can report up to several hundred events. Note that the first event is the oldest and thateach event has a time stamp indicating the...

52 Sun Fire V100 Server User’s Guide • December 2001 ▼ To View the Entire Event Log ● Type: where x is the number of lines you want to display before pausing, and y is the severity level of the events you want to see. By default, the loghistory command displays all the events in the log and does not...

Chapter 5 Managing the Sun Fire V100 Server From the lom> Prompt 53 ▼ To View All Events From the Last One Loggedto the nth Event Before It ● Type: where n is the number of events you want to see listed that were logged before thelast event in the current log, x is the number of lines you want to...

54 Sun Fire V100 Server User’s Guide • December 2001 Setting Up LOM Privileges for NamedUsers You can specify up to four named users of the LOM device on a Sun Fire V100server. By default, no users are set up, and therefore no user login prompt appearswhen you use the LOM escape sequence. However, i...

Chapter 5 Managing the Sun Fire V100 Server From the lom> Prompt 55 ▼ To Create a LOM User Account ● Type: where the username is up to eight characters long, begins with an alphabeticcharacter, and contains at least one lowercase alphabetic character. You can use anyof the following characters in...

56 Sun Fire V100 Server User’s Guide • December 2001 ▼ To View the Details of a LOM User Account ● Type: This command displays the details of all users. Note – You must have User Administration ( u -level) authorization to view the details of a LOM user account (see “Permissions Available for LOM Us...

Chapter 5 Managing the Sun Fire V100 Server From the lom> Prompt 57 By default, all four areas of authorization are available to each named user you setup. You can limit users to a particular area or areas of authorization by specifyingpermissions for a named user. ▼ To Specify Permissions for a ...

58 Sun Fire V100 Server User’s Guide • December 2001 ▼ To Quit a LOM Named User Session ● Type: This returns you to the LOM login prompt. Setting the LOM Configurable Variables Note – To be able to run the commands described in this section, the named user must have a -level permission. For more inf...

Chapter 5 Managing the Sun Fire V100 Server From the lom> Prompt 59 ● Turn the alarm off by typing: where n is the number of the alarm you want to turn off: 1, 2, or 3. Alarms 1, 2, and 3 are software flags. They are not associated with any specificconditions, but are available to be set by your ...

60 Sun Fire V100 Server User’s Guide • December 2001 Separating LOM From the Console onthe Serial A/LOM Port By default, the LOM device shares the Serial A/LOM port with the console, andwhen it has an event report to send, it takes control of the Serial A/LOM port itself,interrupting any console act...

62 Sun Fire V100 Server User’s Guide • December 2001 In this file, the reports are displayed with a label identifying them as lom reports and indicating their severity. Starting with the most severe, the levels of severity are: 1. Fatal Fatal events can cause the server to shut itself down. Examples...

66 Sun Fire V100 Server User’s Guide • December 2001 Monitoring the System From the SolarisPrompt To use the Lights-Out Management (LOM) facilities either remotely or locally, youneed a terminal connection to the Serial A/LOM port on the server (see “Setting Upa Console Connection to the Server” on ...

Chapter 6 Managing the Sun Fire V100 Server From the Solaris Prompt 67 ▼ To Check the Fan Status ( lom -f ) ● Type: Checking the Supply Rail Voltages and InternalCircuit Breakers ( lom -v ) The supply rails are the Sun Fire V100 server ’s internal power lines. If the status ofany of these is faulty ...

68 Sun Fire V100 Server User’s Guide • December 2001 ▼ To Check the Status of the Supply Rails andInternal Circuit Breakers ● Type: ▼ To Check the Internal Temperature ● Type: This checks the server ’s internal temperature, and the warning and shutdownthreshold temperatures. # lom -v Supply voltages...

Chapter 6 Managing the Sun Fire V100 Server From the Solaris Prompt 69 ▼ To Check Whether the Fault LED and AlarmsAre On or Off ● Type: Alarms 1, 2, and 3 are software flags. They are not associated with any specificconditions, but are available to be set by your own processes or from the commandlin...

70 Sun Fire V100 Server User’s Guide • December 2001 ● To configure the LOM device to perform an automatic server restart (ASR) after alockup, you must enable the Hardware reset option as well as the Watchdog option. For more information, see “Configuring Automatic Server Restart” on page 73. ▼ To V...

72 Sun Fire V100 Server User’s Guide • December 2001 ▼ To View the Event Log ( lom -e ) ● To see the event log, type: where n is the number of reports (up to 128) that you want to see and x specifies thelevel of reporting you require. There are four levels of event reporting: 1. Fatal events2. Warni...

Chapter 6 Managing the Sun Fire V100 Server From the Solaris Prompt 73 FIGURE 6-1 Sample LOM Device Event Log (Oldest Event Reported First) Configuring Automatic Server Restart You can configure automatic server restart (ASR) to restart a server automaticallyafter a lockup. LOM has a watchdog proces...

Chapter 6 Managing the Sun Fire V100 Server From the Solaris Prompt 75 ● If you have no LOM watchdog process running already and you want the processto run, type the following, or add it to another script file: ● If you want the LOM device to perform an automatic server restart after a lockup,you mu...

76 Sun Fire V100 Server User’s Guide • December 2001 Other LOM Tasks You Can PerformFrom the Solaris Prompt This section describes how to: ■ Turn the alarms and Fault LEDs on and off with the lom command. ■ Change the first character of the lom escape sequence. ■ Stop LOM sending reports to the Seri...

Chapter 6 Managing the Sun Fire V100 Server From the Solaris Prompt 77 ● To turn the Fault LED off, type: ▼ To Change the First Character of the Sequencefor Escaping to the lom> Prompt ( lom -X ) The character sequence #. (hash, dot) enables you to exit the Solaris prompt to the lom> prompt. ●...

78 Sun Fire V100 Server User’s Guide • December 2001 ● To turn serial event reporting on again, type: If you want to dedicate the Serial A/LOM port to the LOM device and you want touse the Serial B port as your console port, see “To Dedicate Serial A/LOM to LOM”on page 60. ▼ To Make the LOM Interfac...

84 Sun Fire V100 Server User’s Guide • December 2001 FIGURE 7-2 Back-Panel Power and Fault LEDs ▼ To Turn the Fault LED On or Off ● To turn the Fault LED on, type: ● To turn the Fault LED off, type : For information about turning the Fault LEDs on and off from the LOM shell, seeChapter 5. For more i...

86 Sun Fire V100 Server User’s Guide • December 2001 Adding Components or Replacing AServer For a list of components that are available for the Sun Fire V100 server, see “OptionalComponents” on page 4. If there is a fault with any of the components listed below,replace the whole server. Should you n...

Chapter 8 Removing and Replacing Components 87 4. Replace the zip tie on the new system. 5. Power on the new system (see Chapter 4). Caution – Never remove the system configuration card when the server is booting or running Solaris. Power the server off or down to standby mode before removingor inse...

88 Sun Fire V100 Server User’s Guide • December 2001 your area. You can then arrange to return the system to Sun for repair under theterms of your warranty or you can order the components and have them installed byyour own qualified service engineers. Caution – The system contains electronic parts t...

Chapter 8 Removing and Replacing Components 89 2. Hold the On/Standby switch in the Standby position for more than four seconds to put the server in standby mode. 3. Disconnect the power cord. 4. Disconnect all other cables. 5. If the system is installed in a rack or cabinet, remove it. ▼ To Remove ...

90 Sun Fire V100 Server User’s Guide • December 2001 3. Slide the top cover back until the arrow on the cover lines up with the arrow on the server body. 4. Lift the cover up and off. ▼ To Replace the Top Cover 1. Align the arrow on the cover with the arrow on the server body. 2. Press the cover dow...

Chapter 8 Removing and Replacing Components 91 4. Tighten the captive screw on the back of the unit. Memory Installation and Removal There are four industry standard PC133 memory module sockets on the Sun FireV100 server ’s system board. To see the location of the memory modules inside theserver, se...

92 Sun Fire V100 Server User’s Guide • December 2001 FIGURE 8-6 Installing Memory Into a Socket on the System Board 5. If you are removing memory, open the latches and remove the module(s) in the order 0, 1, 2, 3. 6. Replace the system cover and tighten the captive screw (see FIGURE 8-4 ). Installin...

Chapter 8 Removing and Replacing Components 93 ■ If the server is already in use, see “To Change Components In a Sun Fire V100Server That Is In Use” on page 88. 1. Place the unit on an ESD surface and attach an antistatic wrist strap (see FIGURE 8-2 ). 2. Remove the server ’s top cover (see “To Remo...

94 Sun Fire V100 Server User’s Guide • December 2001 FIGURE 8-8 Installing a Hard Disk Drive 5. Attach the power and data cables (see FIGURE 8-8 ). 6. Replace the system cover and tighten the captive screw (see FIGURE 8-4 ). ▼ To Remove a Hard Disk Drive ■ If the server is not in use, go straight to...

Chapter 8 Removing and Replacing Components 95 4. Unfasten the hard disk drive’s handle from the two clips securing it. 5. Slide the hard disk drive until it is free from the clips on the base of the server. 6. Lift the hard disk drive up and out of the server.

97 C H A P T E R 9 Reinstalling the Solaris Operating Environment This chapter explains how to reinstall the Solaris operating environment onto theSun Fire V100 server. It contains the following sections: ■ “Reinstalling the Solaris Operating Environment” on page 98 ■ “Reinstalling the Lights-Out Ma...

99 C H A P T E R 10 Troubleshooting This chapter describes the diagnostic tools you can use with the Sun Fire V100server, lists some of the problems you might encounter when setting up or using aserver, and gives information to help fix those problems. The information iscontained in the following se...

100 Sun Fire V100 Server User’s Guide • December 2001 Diagnostic Tools The following troubleshooting tools are available for the servers: ■ Power On Self Test (POST) Diagnostics ■ OpenBoot Diagnostics (OBDiag) ■ SunVTS POST Diagnostics To view Power On Self Test (POST) diagnostic and error messages ...

Chapter 10 Troubleshooting 101 OpenBoot Diagnostics Like POST diagnostics, OpenBoot Diagnostics can be run if the diag-switch? variable is set to true . You can also run OpenBoot Diagnostics interactively and select which tests you wantit to perform. To do so, follow the steps below from the ok prom...

102 Sun Fire V100 Server User’s Guide • December 2001 3. When you have finished testing, exit OpenBoot Diagnostics and restore the value of auto-boot? to true. To do this, type: The function of each test is shown below. Setting the Diagnostic Level for POST and OpenBootDiagnostics There are three le...

Chapter 10 Troubleshooting 103 ● Type: SunVTS SunVTS, the Sun Validation and Test Suite, is an online diagnostics tool which youcan use to verify the configuration and functionality of hardware controllers, devicesand platforms. It runs in the Solaris 8 operating environment using any of thefollowin...

104 Sun Fire V100 Server User’s Guide • December 2001 ■ If SunVTS software is not loaded, you will see the following error message: Installing SunVTS By default, SunVTS is not installed on the Sun Fire V100 server. SunVTS isdistributed via the Software Supplement for the Solaris Operating Environmen...

Chapter 10 Troubleshooting 105 You can fine-tune your testing session by selecting the appropriate check boxes foreach of the tests you want to run. Problems You Might Encounter This section outlines some particular problems you might encounter when settingup and using the Sun Fire V100 server and, ...

106 Sun Fire V100 Server User’s Guide • December 2001 Cannot Display the lom> Prompt Using the #. Escape Sequence Check whether the first character of the #. escape sequence has been changed (this is a user-configurable value). To check the current value, type the following from theSolaris prompt...

Chapter 10 Troubleshooting 107 IDE Controller Failure The probe-IDE diagnostic transmits an inquiry command to internal and externalIDE devices connected to the system’s on-board IDE interface. If the IDE device isconnected and active, the target address, unit number, device type, andmanufacturer na...

108 Sun Fire V100 Server User’s Guide • December 2001 Frequently Asked Questions What hardware configurations is the Sun Fire V100 available in? The Sun Fire V100 server is available in the following configurations: What software is preinstalled? The Sun Fire V100 server comes preinstalled with the ...

110 Sun Fire V100 Server User’s Guide • December 2001 How many Sun Fire V100 servers can be put in a standard 19-inch rack? Physically and electrically, you can put up to 40 Sun Fire V100 servers into astandard 19-inch rack with two 20-amp circuits. However, a more practicaldeployment would be 32 se...

Chapter 10 Troubleshooting 111 Do the serial ports support synchronous protocols? No. Will the server need a null-modem cable to connect to the console port? No. Because the Sun Fire V100 server requires the use of console port, Sun hasdesigned the server not to need a null-modem cable. All you need...

116 Sun Fire V100 Server User’s Guide • December 2001 Physical Specifications Environmental Specifications You can operate and store the system safely in the conditions detailed below. Acoustic Noise Generated The system generates less than 60 dBA at a distance of 23.67 inches (600 mm) and aheight o...

Appendix A Physical and Environmental Specifications 117 Environmental Compliance Information ■ Electromagnetic compatibility ■ Immunity: The server conforms to EN55024. ■ Emissions: The server conforms to EN55022 Class A and FCC Class A. ■ SafetyThe system conforms to UL 1950 (3rd edition), EN60950...

118 Sun Fire V100 Server User’s Guide • December 2001 Note – Power from the standby output is available whenever input power is connected. Calculating Power Consumption A Sun Fire V100 server containing two disk drives has an estimated currentrequirement of approximately 1 amp. TABLE A-3 shows the e...

119 A P P E N D I X B Configuring LOM Driver This appendix describes the parameters that you can use to configure the LOMdriver, and contains the following sections: ■ “The LOM Device Driver and Script Files” on page 120 ■ “Configuring the LOM Device Driver” on page 121

120 Sun Fire V100 Server User’s Guide • December 2001 The LOM Device Driver and Script Files The LOM driver software included in the Solaris 8 (10/00) operating environment isas follows: ■ /platform/sun4u/kernel/drv/lom (the lom driver [32-bit]) ■ /platform/sun4u/kernel/drv/sparcv9/lom (the lom driv...

Appendix B Configuring LOM Driver 121 Configuring the LOM Device Driver The full list of parameters you can set in this file is given in TABLE B-1 . TABLE B-1 LOM Configuration File Parameters Field Format Default Effect wdog_reset= Boolean0=FALSE1=TRUE 0 Causes LOM to reset the serverafter a watchd...

Index-125 A acoustic noise, 116alarms, setting, 62, 76altitude, 116anti-static wrist strap, 88automatic server restart, 73 B back panel LEDs, 82BTU rating, 117 C cables, 17Cisco L2511 Terminal Server, connecting, 25console connection ASCII terminal, 24setting up, 20Sun workstation, 24terminal server...