Sterling SSV 05/R - Manuals

1. Safety in struc tions » These safety in struc tions ap ply to all per sons within the range of ac tion of the equip ment. Please in form all per sons within the range of ac tion of the equip -ment of the di rect and in di rect haz ards con nected with the equip ment. These op er at ing in struc t...

1.1. Warn ings and sym bols The fol low ing warn ings and sym bols are used in these op er at ing in struc tions: » This sym bol in di cates dan ger to life! Fa tal or se ri ous in jury ispos si ble if the cor re spond ing in struc tions, reg u la tions or warn -ings are not observed. L This sym bol...

1.3. For your safety · The op er a tors of this unit must be at least 16 years old. · Be fore ini tial op er a tion, read this op er at ing man ual care fully. Ob serve all points.In quire in case of un cer tain ties. This will avoid dan ger to per sons and dam age of material! · Store this op er at...

· Do not carry through mod i fi ca tions, at tach ments or al ter ations of the unit with outthe man u fac turer’s per mis sion. Dan ger of accidents! · By means of this op er at ing man ual, pre pare pre cise in struc tions for use of thisunit. Faulty op er a tion may lead to ac ci dents! · Des ig ...

· At tach ments which are not de liv ered by Ster ling must be con structed ac cord ingto the safety stan dard EN 294. Dan ger of ac ci dents! · Check all lines, hoses and cou pling pieces in reg u lar in ter vals for leak ages anddam age. Any er rors must be elim i nated im me di ately.Dan ger of a...

1.4. For the safety of the units · The unit may only be used for con vey ing cy lin dri cal plas tic gran ules and regrindon in jec tion mould ing ma chines. · Never change set tings un less you are able to pre cisely fore see the con se -quences. · Use only orig i nal Ster ling spare parts. · Ob se...

2. In stal la tion in struc tions » These in stal la tion in struc tions are in tended for per sons withskills in elec tri cal and me chan i cal ar eas due to their train ing, ex -pe ri ence and re ceived in struc tions.Per son nel us ing these in stal la tion in struc tions must be in -structed in ...

2.1. Gen eral in for ma tion Un pack all parts of the sin gle con veyor unit and make sure that ev ery thing isavail able: · con veyor hop per with level probe (A) · con trol and main te nance unit (B) · in jec tor tube (C) · sup ply hose (D) with 2 hose clamps · com pressed-air hose (E) · op er at ...

2.2. In stall ing the con veyor hop per The sin gle con veyor unit is not sen si tive to shocks and can be in stalled di rectly on the pro cess ing ma chine. Make sure that all con nec tions are tight so that the con vey ing per for mance is notim paired. The con veyor hop per is equipped with a uni...

2.4. Con nect ing the com pressed-air sup ply Check com pressed-air pip ing for cor rect in stal la -tion and as sem bly. Check fit tings, length and qual ity of the hose con -nec tions for agree ment with re quire ments. Check all com pressed-air lines for leak ages. You need a com pressed-air sup ...

2.5. Elec tri cal con nec tion » Ob serve the reg u la tions of the lo cal elec tric ity board. The op er at ing volt age is 230 V, AC, PE, 50/60 Hz.Spe cial volt ages avail able on re quest. The con nected load is approx. 15 W (0.02 hp). The con nec tion takes place by means of a mains con nec tor....

3. Func tional de scrip tion » This func tional de scrip tion is in tended for the op er at ing per son -nel of the equip ment. Gen eral knowl edge of op er at ing con veyor units is pre req ui site. En sure in each case that the op er at ing per son nel are sufficiently informed. F The sin gle con ...

3.1. Method of func tion ing The sin gle con veyor unit works ac cord ing to theventuri prin ci ple. An ex ter nal com pressed-airsup ply is needed. A venturi me ter (A) is in te grated in the in jec tortube. The venturi me ter as pi rates the ma te rial inthe lower part of the tube (C) and then con...

4.2.1. Fine ad just ment of the fill ing level in the con veyor hop per & Be fore the fine ad just ment, carry through a ba sic ad just -ment. Dur ing op er a tion, care fully turn the ad -just ment screw (A) of the level probe bymeans of a screw driver un til the de siredfill ing level is reach...

5. Main te nance » This chap ter is in tended for per sons with skills in elec tri cal andme chan i cal ar eas due to their train ing, ex pe ri ence and re ceivedin struc tions. Per son nel us ing the in struc tions in this chap ter must be in -structed of the reg u la tions for the pre ven tion of ...

L Dis con nect the equip ment from mains sup ply be fore start ingmain te nance pro ce dures to en sure that it can not be switched on un in ten tion ally. Depressurize all com pressed air pip ing of the equip ment be -fore start ing maintenance work. F Please ob serve the main te nance in ter vals....

5.1. Main te nance in ter vals daily: Check the set ting of the pres sure re ducer.Empty the wa ter sep a ra tor. Check the dan ger signs on the unit for leg i bil ity and com plete ness. monthly: Clean the fil ter and sieve(de pend ing on ac cu mu la tion of dust!).Blow out the fil ter from the in ...

5.2. Clean ing/re plac ing the fil ter car tridge » Switch off the unit. Dis con nect the mains plug. Dis as sem bly Re move the fil ter car tridge (A). Blow out the fil ter car tridge (A) from the in side out by means of com - pressed air or re place the fil ter. Open the tog gle-type fas tener (B)...

As sem bly As sem ble the sieve and the seal ing ring. Check the sieve for proper fit. Clean the hop per loader by means of a vac uum cleaner. Close the hop per lid. Close the tog gle-type fas tener. As sem ble the fil ter car tridge. & Or der num berfil ter car tridge: ID 98171 Sieve: ID 29252 ...

6. Tech ni cal data Max. per mis si ble shot weight of the in jec tion mould ing ma chine: . . . . . . . . . . . . . . . 100 kg/h (with 0.6 kg/l) (220.56lbs/h) with 1.32lbs/l) Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . approx. 3 kg (6.61lbs) O...

6.1. Di men sion sheet 5 0 6- 4 M S SSV 05/R Tech ni cal data 31 Di men sions and data are not bin ding. All di men sions are in mm (in.). All data are sub ject to chan ge.

6.2. Spare parts list 5 0 6- 4 M S SSV 05/R Tech ni cal data 32 A D C B