Speed Queen LDGE5BGS113TW01-THRU-S#1912999999 - Manuals

Gas Models DRY2639N_SVG F E D C B A J K M L I H G 1 1. 3/8 in. NPT Gas Connection A *1027 mm [40.42 in.] B *1006 mm [39.61 in.] C *392 mm [15.44 in.] D *70 mm [2.8 in.] E 60 mm [2.3 in.] F 391 mm [15.4 in.] G 683 mm [26.875 in.] H 102 mm [4 in.] I *114 mm [4.5 in.] J 10 mm [0.4 in.] K 203 mm [8 in.]...

Installation Before You Start Supplies For most installations, the basic supplies you will need are: DRY2586N_SVG 8 7 6 5 4 3 2 1 1. Wrench 2. 1/4 inch Driver 3. Screwdrivers 4. Level 5. Gloves 6. Teflon Tape 7. Duct Tape 8. Safety Glasses Figure 1 NOTE: This appliance is suitable for use in countri...

Area Description Free Standing/Alcove In- stallation Closet Installation A* Dryer sides and rear clearance 0 mm [0 in.] 0 mm [0 in.] B Dryer top clearance 305 mm [12 in.] 305 mm [12 in.] C Dryer front clearance Not Applicable 51 mm [2 in.] D Exhaust duct clearance to com-bustible material 51 mm [2 i...

WARNING To reduce the risk of fire, DO NOT use plastic or thinfoil ducting to exhaust the dryer. W354 WARNING To reduce the risk of fire, the exhaust duct andweather hood MUST be fabricated of a material thatwill not support combustion. Rigid or flexible metalpipe is recommended for a clothes dryer....

Exhausting the dryer through sides or bottom can be accomplish-ed by installing a Directional Exhaust Kit, 528P3, available asoptional equipment at extra cost. Exhaust System For best drying results, recommended maximum length of ex-haust system is shown in Table 2 . To prevent backdraft when dryer ...

D233I_SVG 2 3 4 1 5 1. New Stainless Steel Flexible Connector – (Use designCSA certified connector) Use only if allowed by local co-des 2. 1/8 in. NPT Pipe Plug 3. Equipment Shut-Off Valve 4. Black Iron Pipe: Shorter than 6.1 m [20 ft.] – Use 9.5 mm [3/8 in.] pipe. Longer than 6.1 m [20 ft.] – Use 1...

WARNING Improper connection of the equipment earth/groundconductor can result in a risk of electric shock.Check with a qualified electrician or service person ifyou are in doubt as to whether the dryer is properlyconnected to a protective earth/ground. W886 Do not modify the plug provided with the c...

3. Use a strain relief and insert end of power cord through power supply hole. D696I_SVG Figure 8 4. Use the three screws from the accessories bag to attach the power cord wires to the terminal block. Refer to Figure 9 . 3-Wire Connection DRY2508N_SVG 4 3 2 1 1. "L1" Terminal 2. Neutral Term...

DRY2468N_SVG 1 1. Earth/Ground Screw Figure 12 4. Use a strain relief and insert end of power cord through power supply hole. DRY2469N_SVG 1. Strain Relief Figure 13 5. Attach power cord earth/ground (green) wire to rear bulkhead using earth/ground screw removed in Step 3. 4-Wire Connection DRY2482N...

8. Using screwdriver, remove two door plugs, and reinstall on opposite side of door opening. DRY2503N_SVG Figure 22 9. Reinstall four hinge attaching screws, removed in Step 1. D606I_SVG Figure 23 Wipe Out Inside of Dryer Before using dryer for the first time, use an all-purpose clean-er, or a deter...

The dryer is designed to be operated on a separate branch, polar-ized, three-wire, effective earth/ground, 120 Volt, 60 Hertz, AC(alternating current) circuit protected by a 15 Ampere fuse,equivalent fusetron or circuit breaker. The three-prong earth/ground plug on the power cord should beplugged di...

IMPORTANT: This operation is to be conducted byqualified personnel only. 1. To view the burner flame, remove the lower front panel of the dryer. 2. Close the loading door and start the dryer in a heat setting (re- fer to the operation instructions). The dryer will start, the ig-niter will glow red a...

Installer Checklist Fast Track for Installing the Dryer 1 Position and Levelthe Dryer. DRY2634N_SVG 5 Reverse Door, if De-sired. DRY2052N_SVG1 CHECK CHECK 2 Connect Dryer ExhaustSystem. DRY2501N_SVG1 6 Wipe Out Inside ofDryer. DRY2504N_SVG1 CHECK CHECK 3 GAS ONLY• Connect Gas Sup- ply Pipe. • Check ...