Speed Queen ATGE9ASP116TW01 - Manuals

* With leveling legs turned into base. ** For ADA compliance turn legs out from base 0.5 inches. NOTE: Exhaust openings are 102 mm [4 inch] metalducting. Gas Models SWD1051N_SVG I H G F E D C B A K M L J Q R O S P N 1 1. 3/8 in. NPT Gas Connection A *1678 mm [66.06 in.] B *1447 mm [56.97 in.] C 597 ...

Installation Before You Start Tools For most installations, the basic tools you will need are: SWD1021N_SVG 11 10 9 8 4 3 2 1 6 7 5 1. Wrench 2. 1/4 inch Driver 3. Screwdriver 4. Level 5. Wood Block 6. Pliers 7. 5/16 Inch Socket Wrench 8. Gloves 9. Teflon Tape (Gas Models) 10. Duct Tape 11. Safety G...

1. Lift dryer and place it on top of washer so dryer leveling legs sit in notches in control cabinet. 2. Slide dryer backward until mounting holes in base line up with holes in front of security cabinet. 3. Reconnect dryer wire harness. If needed, refer to unit’s wiring diagram. 4. Tip dryer and rep...

Remove Shipping Materials 1. Remove two screws at bottom of front access panel. Rotate bottom of panel out and remove panel. FLW2378N_SVG Figure 2 2. Remove two 9/16 inch bolts and washers holding shipping brace to weight. 3. Remove two 9/16 inch bolts and washers holding shipping brace to washer ba...

Water Supply Requirements Water supply faucets must fit standard 19 mm [3/4 inch] femalegarden hose couplings. DO NOT USE SLIP-ON OR CLAMP-ON CONNECTIONS. NOTE: Water supply faucets should be readily accessi-ble to permit turning them off when washer is not beingused. Recommended cold water temperat...

W005I_SVG 2 1 1. Risers (Air cushions) 2. Water Supply Faucets Figure 7 Connect Drain Hose to Drain Receptacle Remove the drain hose from its shipping position on the rear ofthe washer by unhooking the hose from the retainer clamp and byremoving the shipping tape. Install the drain hose into the dra...

H023i_SVG 1 3 2 1. Drain Hose 2. Beaded Strap (tape if necessary) 3. Fill Hoses Figure 9 Laundry Tub Installation For this type of installation, the drain hose MUST be secured tothe stationary tub to prevent hose from disloding during use. Re-fer to Figure 10 . Use the beaded strap (supplied in acce...

Natural Gas Altitude Adjustments Altitude Orifice Size Part No. m [feet] No. mm [inches] 2440 [8000] 45 2.08 [0.0820] D503779 2740 [9000] 46 2.06 [0.0810] D503780 3050 [10,000] 47 1.99 [0.0785] D503781 Table 1 2. Remove the shipping cap from the gas connection at the rear of the dryer. Make sure you...

L.P. Altitude Adjustments Altitude Orifice Size Part No. m [feet] No. mm [inches] 915 [3000] 55 1.32 [0.0520] 58755 2440 [8000] 56 1.18 [0.0465] D503786 Table 2 Electric Dryer Only - Connect Electrical Plug Dryer requires 120/240 Volt or 120/208 Volt, 60 Hertz, 3 or 4wire electrical supply. Refer to...

3. Use a strain relief and insert end of power cord through power supply hole. D696I_SVG Figure 14 4. Use the three screws from the accessories bag to attach the power cord wires to the terminal block. Refer to Figure 15 . 3-Wire Connection DRY2508N_SVG 4 3 2 1 1. "L1" Terminal 2. Neutral Te...

Connect Dryer Exhaust System WARNING To reduce the risk of fire and combustion gas accu-mulation the dryer MUST be exhausted to the out-doors. W604 WARNING To reduce the risk of fire and the accumulation ofcombustion gases, DO NOT exhaust dryer air into awindow well, gas vent, chimney or enclosed, u...

• Exhausting dryer in hard-to-reach locations can be done by installing 521P3 Flexible Metal Vent Kit (available as option-al equipment at extra cost). • Sufficient make-up air must be supplied to replace the air ex- hausted by the dryer. The free area of any opening for outsideair must be at least ...

SWD1053N_SVG 4 5 3 2 6 1 1. Level 2. Wood Block 3. Rubber Foot 4. Leveling Leg 5. Locknut 6. Unit Base Figure 22 Reverse Door, if Desired NOTE: Doors with windows cannot be reversed. The door on this dryer is completely reversible. To reverse doorproceed as follows:1. Remove four hinge attaching scr...

SWD1055N_SVG Figure 33 Plug In the Washer and Dryer Electric Dryer Connect the dryer to an electrical power source. Refer to ConnectElectrical Plug section for information on connecting power cord. Connect to 30 Amp Circuit D275I_SVG2 Figure 34 Gas Dryer Dryer requires 120 Volt, 60 Hertz electrical ...

Plug Cord Into Separately Fused 15 Amp Circuit TLW2287N_SVG 6 8 7 2 1 3 5 4 1. L1 2. Earth/Ground 3. Neutral 4. Round Earth/Ground Plug 5. Neutral Side 6. 0 V.A.C. 7. 120 ± 12 V.A.C. 8. 120 ± 12 V.A.C. Figure 35 Earth/Ground Information This appliance must be properly connected to protective earth/g...

WARNING To reduce the risk of fire, electric shock, serious in-jury or death, all wiring and protective earth/groundconnections MUST conform with the latest edition ofthe National Electrical Code, ANSI/NFPA No. 70, andsuch local regulations as might apply. It is the cus-tomer’s responsibility to hav...

led and connected to a protective earth/ground in accordance withall local codes and ordinances. WARNING Improper connection of the equipment earth/groundconductor can result in a risk of electric shock.Check with a qualified electrician or service person ifyou are in doubt as to whether the unit is...

Gas Dryers IMPORTANT: This operation is to be conducted byqualified personnel only. 1. To view the burner flame, remove the lower front panel of the dryer. 2. Close the loading door and start the dryer in a heat setting (re- fer to the operation instructions). The dryer will start, the ig-niter will...

Installer Checklist Fast Track for Installing the Stacked Washer/Dryer 1 Position Unit Near Installation Area. 7 Connect Dryer ExhaustSystem. SWD997N_SVG1 CHECK CHECK 2 Remove the Shipping Ma-terials and Install Plugs. FLW2359N_SVG 8 Position and Level theWasher. SWD1056N_SVG1 CHECK CHECK 3 Connect ...