Speed Queen ADG3LRGS111TW01 - Manuals

Gas Dryers DRY2293N_SVG O N M L K I H G F E D C B A J 1. 3/8 in. N.P.T. Gas Connection A 22.38 in. [569 mm] B 8.0 in. [203 mm] C * 36 in. [914 mm] D * 40.25 in. [1022 mm] E * 43 in. [1092 mm] F 15.4 in. [391 mm] G * 15.44 in. [392 mm] H * 2.8 in. [70 mm] I 2.3 in. [60 mm] J 26.875 in. [683 mm] K * 4...

Installation Before You Start Supplies For most installations, the basic supplies you will need are: 9/1 6" DRY2023N_SVG 8 7 6 5 3 2 1 4 1. Safety Glasses 2. Power Cord (Electric Models) 3. Wrench 4. Screwdriver 5. Level 6. 5/16 Inch Socket Wrench 7. Duct Tape 8. Teflon Tape (Gas Models) Figure ...

Area Description Free Standing/Alcove In- stallation Closet Installation A* Dryer sides and rear clearance 0 in. [0 mm] 0 in. [0 mm] B Dryer top clearance 12 in. [305 mm] 12 in. [305 mm] C Dryer front clearance Not Applicable 2 in. [51 mm] D Exhaust duct clearance to com-bustible material 2 in. [51 ...

WARNING To reduce the risk of fire, DO NOT use plastic or thinfoil ducting to exhaust the dryer. W354 DRY1915N_SVG 2 1 1. Correct 2. Incorrect Figure 4 • DO NOT use plastic, thin foil or type B ducting. Rigid metal duct is recommended. • Locate dryer so exhaust duct is as short as possible.• Be cert...

Gas Dryers - Connect Gas Supply Pipe WARNING To reduce the risk of gas leaks, fire or explosion: • The dryer must be connected to the type of gas as shown on nameplate located in the door re-cess. • Use a new flexible stainless steel connector.• Use pipe joint compound insoluble in L.P. (Lique- fied...

D233I_SVG 2 3 4 1 5 1. New Stainless Steel Flexible Connector – (Use designCSA certified connector) Use only if allowed by local co-des 2. 1/8 in. NPT Pipe Plug 3. Equipment Shut-Off Valve 4. Black Iron Pipe: Shorter than 20 ft. [6.1 m] – Use 3/8 in. [9.5 mm] pipe. Longer than 20 ft. [6.1 m] – Use 1...

WARNING Improper connection of the equipment-groundingconductor can result in a risk of electric shock.Check with a qualified electrician or service person ifyou are in doubt as to whether the dryer is properlygrounded. W038 Do not modify the plug proivded with the cord-kit - if it will notfit the o...

3. Use a strain relief and insert end of power cord through power supply hole. D696I_SVG Figure 8 4. Use the three screws from the accessories bag to attach the power cord wires to the terminal block. Refer to Figure 9 . D286I_SVG 3 2 1 1. "L1" Terminal 2. Neutral Terminal 3. "L2" Te...

DRY2468N_SVG 1 1. Ground Screw Figure 12 4. Use a strain relief and insert end of power cord through power supply hole. DRY2469N_SVG Figure 13 5. Attach power cord earth/ground (green) wire to rear bulkhead using earth/ground screw removed in Step 3. DRY2482N_SVG 1 2 3 4 5 6 7 8 1. Neutral Terminal ...

D620I_SVG Figure 22 9. Reinstall four hinge attaching screws, removed in Step 1. D623I_SVG Figure 23 Wipe Out Inside of Dryer Before using dryer for the first time, use an all-purpose clean-er, or a detergent and water solution, and a damp cloth to re-move shipping dust from inside dryer drum. D618I...

is equipped with a cord having an equipment-grounding conduc-tor and a 3 prong grounding plug. The three-prong groundingplug on the power cord should be plugged directly into a polar-ized three-slot effectively grounded receptacle rated 110/120Volts AC (alternating current) 15 Amps. WARNING This dry...

2. Close the loading door and start the dryer in a heat setting (re- fer to the operation instructions). The dryer will start, the ig-niter will glow red and the main burner will ignite. IMPORTANT: If all air is not purged out of gas line,gas igniter may go off before gas is ignited. If thishappens,...

Installer Checklist Fast Track for Installing the Dryer 1 Position and Level theDryer. DRY2634N_SVG 6 Wipe Out Inside ofDryer. D618I_SVG1 CHECK CHECK 2 Connect Dryer ExhaustSystem. DRY1915N_SVG1 7 Plug In the Dryer. Electric D275I_SVG1 Gas D254I_SVG CHECK CHECK 3 GAS ONLY • Connect Gas Sup- ply Pipe...