Speed Queen ADE3SRGS175TW01-START-S#2001000001 - Manuals

Gas Dryers 1. 3/8 in. N.P.T. Gas Connection A 22.38 in. [569 mm] B 8.0 in. [203 mm] C * 36 in. [914 mm] D Electronic Control: *41.25 in. [1048 mm] Knob Control: *40.75 [1035 mm] E * 42.75 in. [1086 mm] F 15.4 in. [391 mm] G * 15.44 in. [392 mm] H * 2.8 in. [70 mm] I 2.3 in. [60 mm] J 26.875 in. [683...

Installation Before You Start Supplies For most installations, the basic supplies you will need are: DRY2586N_SVG 8 7 6 5 4 3 2 1 1. Wrench 2. 1/4 inch Driver 3. Screwdrivers 4. Level 5. Gloves 6. Teflon Tape 7. Duct Tape 8. Safety Glasses Figure 1 NOTE: This appliance is suitable for use in countri...

Area Description Free Standing/Alcove In- stallation Closet Installation A* Dryer sides and rear clearance 0 in. [0 mm] 0 in. [0 mm] B Dryer top clearance 12.25 in. [305 mm] 12.25 in. [305 mm] C Dryer front clearance Not Applicable 2 in. [51 mm] D Exhaust duct clearance to com-bustible material 2 in...

WARNING To reduce the risk of fire, DO NOT use plastic or thinfoil ducting to exhaust the dryer. W354 WARNING To reduce the risk of fire, the exhaust duct andweather hood MUST be fabricated of a material thatwill not support combustion. Rigid or flexible metalpipe is recommended for a clothes dryer....

Number of 90° Elbows Weather Hood Type Recommended Use Only for Short Run Installations D673I_SVG 1 1 1. 4 in. [102 mm] D802I_SVG 1 1. 2.5 in. [64 mm] Maximum length of 4 in. [102 mm] diameter rigid metal duct. 0 65 feet [19.8 m] 55 feet [16.8 m] 1 55 feet [16.8 m] 47 feet [14.3 m] 2 47 feet [14.3 m...

1. Make certain your dryer is equipped for use with the type of gas in your laundry room. Dryer is equipped at the factory forNatural Gas with a 3/8 inch NPT gas connection. NOTE: The gas service to a gas dryer must conformwith the local codes and ordinances, or in the ab-sence of local codes and or...

L.P. (Liquefied Petroleum) Gas, 2500 Btu/ft. 3 [93.1 MJ/m 3 ], serv- ice must be supplied at 10 ± 1.5 inch water column pressure. For proper operation at altitudes above 3000 feet [915 m] the L.P.gas valve spud orifice size must be reduced to ensure completecombustion. Refer to Table 4 . L.P. Altitu...

D695I_SVG Figure 7 3. Use a strain relief and insert end of power cord through power supply hole. D696I_SVG Figure 8 4. Use the three screws from the accessories bag to attach the power cord wires to the terminal block. Refer to Figure 9 . 3-Wire Connection DRY2508N_SVG 4 3 2 1 1. "L1" Termi...

3. Remove earth/ground screw from earth/ground to neutral wire and save for use in Step 5. Earth/ground to neutral wire willbe attached to the neutral terminal in Step 6. DRY2468N_SVG 1 1. Earth/Ground Screw Figure 12 4. Use a strain relief and insert end of power cord through power supply hole. DRY...

8. Using screwdriver, remove two door plugs, and reinstall on opposite side of door opening. D317S_SVG Figure 22 9. Reinstall four hinge attaching screws, removed in Step 1. D606I_SVG Figure 23 Wipe Out Inside of Dryer Before using dryer for the first time, use an all-purpose clean-er, or a detergen...

• Do not overload circuits.• Do not use an adapter.• Do not use an extension cord.• Do not operate both a washer and gas dryer on the same cir- cuit. Use separately fused 15 amp circuits. The dryer is designed to be operated on a separate branch, polar-ized, three-wire, effectively grounded, 120 Vol...

Installer Checklist Fast Track for Installing the Dryer 1 Position and Level theDryer. DRY2634N_SVG 6 Wipe Out Inside ofDryer. CHECK CHECK 2 Connect Dryer ExhaustSystem. 7 Plug In the Dryer. Electric D275I_SVG1 Gas TLW2289N_SVG CHECK CHECK 3 GAS ONLY • Connect Gas Sup- ply Pipe. • Check for Gas Leak...