SpectraLink Link 150 M3 MCU - Manuals

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 1. About This Document This document explains installation and operation of SpectraLink’s Link Wireless Telephone System (Link WTS), using the Link 150 Model 3 (M3) Master Control Unit (MCU). The Link 150 M3 MCU adds wirel...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 2. Installation Overview Installation has three phases. In most cases, a separate person is responsible for each phase. 1. Site preparation and wire installation: This is usually done by a wire technician or contractor. 2....

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 2.1 Installation Steps and Responsibilities 9 Task Description Wire Contractor or Electrician Field Service Engineer Customer Project Mgr/ System Admin Site Preparation Determine location of MCU 9 Run Cable for System Run ...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 3. Link Wireless Telephone System Overview Review this section if you are unfamiliar with the features and operation of the Link WTS. 3.1 System Operation The Link WTS is a wireless communication system that offers direct ...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU SpectraLink offers an analog MCU that works with telephone systems (CO, PBX or Key Systems) with analog (loop start) ports. We also offer digital MCUs that work with the most common brands of telephone systems’ (PBX or key...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 3.2 The Front Panel of the Link 150 M3 MCU The MCU’s front panel contains the connections to the telephone system, switches to control system administration, and status LEDs. 1. STEP Button : Selects a specific line or Bas...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 4. Site Preparation 4.1 Required Materials The following equipment must be provided by the customer: † Outlet Strip Recommended for installations with more than one MCU. This will allow the MCUs to be turned on and off tog...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 5. Run Cable for System 5.1 Run Cables to Base Station Locations The Base Station locations should be designated on the building floor plans provided to the SpectraLink field service engineer. Base Stations can be mounted ...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU When cabling an external Base Station or a Base Station with wiring that exits the building, protect all Base Station wiring with the Quick Clip Fuse (Illinois Tool Works, Linx Division, SCP-2X2) before bridging with other...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU When wiring the 8-pin connector, use the following table as a guide. 8-pin Modular Connector MCU Pin Function Polarity 1 Data 1 Any 2 Data 2 Any 3 Power 3 + 4 Power 2 - 5 Power 2 + 6 Power 3 - 7 Power 1 - 8 Power 1 + 5.4 P...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU Multiple Power Pairs Some sites may prefer to wire Base Stations to a separate demarc block in order to split out power pairs. Dedicated Line for Diagnostic Modem The Link 150 M3 MCU can be accessed remotely using an inter...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU Four-wire Digital Interface The wiring diagram below shows the connections required for a four-wire interface . Each MCU of this type requires two demarcation blocks which will be wired as indicated. A B Receive (RX) To PB...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 5.5 Install Demarc Blocks The demarcation blocks used to connect the telephone system and Base Stations to the MCU should be installed on a typical telephone facility backboard. A 1/2” or 3/4” thick board mounted on the wa...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU Two-wire Analog or Digital Demarc Block The demarc block for the two-wire analog or digital interface should be wired as follows. LINE1 tip ring LINE 2 tip ring LINE 3 tip ring LINE 4 tip ring LINE 5 tip ring LINE 6 tip ri...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU Four-wire Digital Demarc Block The four-wire digital interface (future release) requires two demarc blocks, one to Connector A and one to Connector B on the MCU. They should be wired as follows. Line 1 TX tip ring Line 2 T...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU Line 1 RX tip ring Line 2 RX tip ring Line 3 RX tip ring Line 4 RX tip ring Line 5 RX tip ring Line 6 RX tip ring Line 7 RX tip ring Line 8 RX tip ring Line 9 RX tip ring Line 10 RX tip ring Line 11 RX tip ring Line 12 RX ...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 6. Install Link Wireless Telephone System 6.1 Survey Site Check the site to be sure pre-installation work has been completed correctly. This includes: • Location chosen for the MCU is adequate, and power is available. • Wi...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU † ESD Bonding Straps To provide static protection for the MCU. † Link Wireless Telephones The correct number of handsets for this installation. † Battery Chargers Link Wireless Telephones require a Battery Charging system,...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU Connect Multi-Unit Systems Use the following procedure to connect multiple MCUs. 1. Mount the MCUs side by side. 2. Connect the IPC cable from the OUT port of the first unit to the IN port of the adjacent unit. Repeat unti...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU Connect Power 1. Connect the power plug from the AC adapter to the jack labeled PWR on the MCU. Use only the provided Class II AC Adapter with output 24VDC, 1A. For installations with more than one MCU, use an outlet strip...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU Switch Interface Line LEDs MCU Type Notes Analog 1 SCA5xx The SCA will only support Analog. Comdial 3 SCU5xx DEFINITY – Two-wire 1, 4 SCU5xx DEFINITY – Four-wire 1, 5 SCF5xx Four-wire Interface. Executone 2, 5 SCB5xx The S...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 6.4 Install Base Stations Be sure the Base Station is positioned clear of anything that might damage it. The Base Station should be well above head height, away from doors and other objects that might strike it, and away f...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU Mount Base Stations On Finished Ceilings If your site does not have a dropped tile ceiling, the Base Station can be mounted to a finished ceiling or wall with a 4 to 5” long 1/4” –20 TPI plastic or nylon screw or bolt (suc...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 6.5 Install Outdoor Base Stations Outdoor Base Stations are equipped with a protective enclosure, designed to be mounted to a wall or pole. After the enclosure is mounted, the Base Station is inserted in the enclosure and ...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 7. Connect and Register Handsets 7.1 Set Up Diagnostic Modem Each MCU has an internal modem feature that allows SpectraLink technicians to dial into the system for troubleshooting and maintenance. The modem is enabled on L...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU • If the Link 150 M3 MCU is connected to your telephone system via analog lines, refer to the for analog systems. • If your Link 150 M3 MCU is connected to a digital key telephone system or PBX, refer to the document that ...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 8. Site Certification The SpectraLink field service engineer should not leave the site before contacting SpectraLink to perform remote install verification. Contact a SpectraLink engineer on the Customer Support Hotline at...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 9. System Administration 9.1 Troubleshoot Error Codes When an alarm is detected, the ERROR LED will light and the MCU’s STATUS LEDs will display an alarm code. If the error code refers to a Base Station problem, the Base S...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 9.3 Status LED Codes STATUS LEDs 1 2 3 4 5 Description Action Random Cycling The Link 150 M3 MCU is powering up. Initialization to follow. This is not an error and should change to another code after a minute. 5 Link 150 M...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU Handset Status Indicator Messages Indicator Description Action BATT Displays when user is on the handset and the battery charge is low. The user has two minutes to complete the call. Replace the Battery Pack with one that ...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 9.4 Replace a Handset If a handset breaks or needs to be replaced, the old handset must be deleted and the new handset added. Delete Old Handset 1. Make sure all unregistered handsets are off. If this is not done an unregi...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 9.5 Replace an MCU When the system has more than one MCU, each MCU contains a complete set of configuration information for the entire system. This includes handset registration information, function definitions, and frequ...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 9.6 Replace a Base Station To replace a Base Station, unplug the existing Base Station and plug in the new Base Station. • The LED will blink red and green as the system software downloads to the Base Station and the Base ...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 10. Link Wireless Telephone Planning Worksheet Copy and complete this worksheet to keep track of the port numbers, extensions, users, and features assigned to your handsets. MCU ID: _________ Handset # Extension Port ID Us...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 11. Base Station Location Worksheet MCU: ________ Base Station # Location (e.g.: building, floor #, detailed description) Port ID Base Station 1 1 Base Station 2 2 Base Station 3 3 Base Station 4 4 MCU: ________ Base Stati...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU 12.2 Change Companding The factory setting on the Link 150 M3 MCU is compatible with Mu-law companding (signal compression), which is the standard used by most PBXs in North America. Systems outside North America generally...

SpectraLink Corporation Installation and Operation Link WTS – Link 150 M3 MCU Index AC Adapter, 23 A-law, 45 Alternate sequence, 44 Attenuation, 13 Base Station, 23 Cabling, 13, 14 Description, 10 Installation, 28 LED, 35 Location form, 43 Outdoor, 30 Outside Wiring, 30 Replacing, 41 Battery Charger...