SOUNDSTREAM Exact 6.2 - Manuals

Page 2 - Coaxial Speaker System

2 HARDWARE AND CONNECTOR PARTS LIST Congratulations on your purchase of the Soundstream EXACT6.2 Coaxial Speaker System. You now own one of the finest car audio speaker systems available. As with all high quality car audio components, professional installation is recommended. Your dealer’s knowledge...

Page 3 - 5mm Soft Dome Neodymium Tweeter; Ferrofluid-immersed Voice Coil enhances heat dissipation; EXACT6.2X Passive Crossover Network; Variable Tweeter and Midrange Controls for added flexibility; FEATURES

3 The EXACT6.2 Coaxial Speaker System is the result of highly focused engineering effort. Each element of the EXACT6.2 represents several advances in automotive speaker technology. When the project was initiated, the following goals were established: • High performance sound reproduction in the auto...

Page 5 - FIGURE 1

5 INSTALLING THE EXACT6.2 DRIVER The EXACT6.2 Driver can be mounted on the front or rear of a panel; gaskets are provided for both options. The bolt hole configuration will fit a variety of standard American, Asian and European OEM patterns making it ideal for direct replacement. Best performance is...

Page 6 - FIGURE 2

6 TWEETER LEVEL CONTROL The EXACT6.2X Passive Crossover can be mounted in virtually any location inside the vehicle. Be sure not to mount the EXACT6.2X outside the vehicle, or in a location where it may be exposed to dirt or moisture (e.g., the engine compartment, inside a wheel housing, inside a do...

Page 7 - FIGURE 3; Tweeter Protection Activation

7 FIGURE 3 DYNAMIC TWEETER LEVEL CONTROL Tweeter Protection Activation Under high power/high volume conditions, the dynamic tweeter level control (DTLC) circuit may activate. The purpose of DTLC is to prevent failure of the tweeter by reducing its output when necessary. You will notice a decrease in...

Page 8 - FIGURE 4; EXACT6.2 Wiring Diagram; WIRING; Head Unit

8 FIGURE 4 EXACT6.2 Wiring Diagram Figure 4 shows a diagram illustrating the wiring of the EXACT6.2 Component Speaker System. It is important to make sure that all connections are in phase; that is positive (+) is connected to positive (+), and negative (-) is connected to negative (-), since an out...

Page 9 - Figure 5; Crossovers

9 NOTES ON BI-AMPING Bi-Wiring The EXACT6.2 system includes the EXACT6.2X passive crossover which is optimized for the speakers. The EXACT6.2X allows for dual amp inputs. See Figure 5. This feature allows for a 4 channel amplifier or two 2 channel amps to power the four individual drivers of an EXAC...

Page 10 - Amp; Figure 6

10 Bi-Amping T r u e b i - a m p i n g c a n a l s o b e accomplished with an external electronic crossover. See Figure 6. Even greater dynamics can be realized with bandwidth limited amplifiers. If you decide to bi-amp, please follow the recommendations below : 1)Use at least a 12dB/octave high pas...

Page 11 - SPECIFICATIONS; EXACT6.2 System Specifications

11 SPECIFICATIONS EXACT6.2 System Specifications Frequency Response 40 Hz - 20,000 Hz ±3dB Sensitivity 90 dB SPL at 1 meter (2.83v) 96 dB SPL at .5 meter (2.83v) Continuous Power Handling 70 watts Peak Program Power Handling 140 watts Nominal Impedance 4 Ω Crossover Slope Rate 24 dB/octave ASC Cross...

Page 13 - MOUNTING TEMPLATE

13 120 Blue Ravine Road Folsom California 95630 USA tel 916.351.1288 fax 916.351.0414 (Rev A, 4/15/97) MOUNTING TEMPLATE CUT-OUT PILOT HOLE EDGE OFGRILL RING CENTER