SOUNDSTREAM 5.2 - Manuals - manualsarea.com

Page 2 - Coaxial Speaker System

2 HARDWARE AND CONNECTOR PARTS LIST Congratulations on your purchase of the Soundstream EXACT5.2 Coaxial Speaker System. You now own one of the finest car audio speaker systems available. As with all high quality car audio components, professional installation is recommended. Your dealer’s knowledge...

Page 3 - 5mm Soft Dome Neodymium Tweeter; Ferrofluid-immersed Voice Coil enhances heat dissipation; EXACT5.2X Passive Crossover Network; 4 dB/octave Acoustic Summation Crossover Slopes; FEATURES

3 The EXACT5.2 Coaxial Speaker System is the result of highly focused engineering effort. Each element of the EXACT5.2 represents several advances in automotive speaker technology. When the project was initiated, the following goals were established: • High performance sound reproduction in the auto...

Page 5 - FIGURE 1

5 INSTALLING THE EXACT 5.2 DRIVER The EXACT5.2 Driver can be mounted on the front or rear of a panel; gaskets are provided for both options. The bolt hole configuration will fit a variety of standard American, Asian and European OEM patterns making it ideal for direct replacement. Best performance i...

Page 6 - FIGURE 2

6 TWEETER LEVEL CONTROL The EXACT5.2X Passive Crossover can be mounted in virtually any location inside the vehicle. Be sure not to mount the EXACT5.2X outside the vehicle, or in a location where it may be exposed to dirt or moisture (e.g., the engine compartment, inside a wheel housing, inside a do...

Page 7 - FIGURE 3; Tweeter Protection Activation

7 FIGURE 3 DYNAMIC TWEETER LEVEL CONTROL Tweeter Protection Activation Under high power/high volume conditions, the dynamic tweeter level control (DTLC) circuit may activate. The purpose of DTLC is to prevent failure of the tweeter by reducing its output when necessary. You will notice a decrease in...

Page 8 - FIGURE 4; EXACT5.2 Wiring Diagram; WIRING; Head Unit

8 FIGURE 4 EXACT5.2 Wiring Diagram Figure 4 shows a diagram illustrating the wiring of the EXACT5.2 Component Speaker System. It is important to make sure that all connections are in phase; that is positive (+) is connected to positive (+), and negative (-) is connected to negative (-), since an out...

Page 9 - Figure 5; Crossovers

9 NOTES ON BI-AMPING Bi-Wiring The EXACT5.2 system includes the EXACT5.2X passive crossover which is optimized for the speakers. The EXACT5.2X allows for dual amp inputs. See Figure 5. This feature allows for a 4 channel amplifier or two 2 channel amps to power the four individual drivers of an EXAC...

Page 10 - Amp; Figure 6

10 100 500 20 K 5K 1K 20 frequency Active LP and Passive LP dB Active HP and Passive HP 100 500 20 K 5K 1K 20 frequency dB Bi-Amping T r u e b i - a m p i n g c a n a l s o b e accomplished with an external electronic crossover. See Figure 6. Even greater dynamics can be realized with bandwidth limi...

Page 11 - SPECIFICATIONS; EXACT5.2 System Specifications

11 SPECIFICATIONS EXACT5.2 System Specifications Frequency Response 50 Hz - 20,000 Hz ±3dB Sensitivity 90 dB SPL at 1 meter (2.83v) 96 dB SPL at .5 meter (2.83v) Continuous Power Handling 65 watts Peak Program Power Handling 120 watts Nominal Impedance 4 Ω Crossover Slope Rate 24 dB/octave ASC Cross...

Page 13 - MOUNTING TEMPLATE

13 MOUNTING TEMPLATE PILOT HOLES CENTER CUT-OUT EDGE OFGRILL RING 120 Blue Ravine Road Folsom California 95630 USA tel 916.351.1288 fax 916.351.0414 (Rev A, 4/14/97)