Sony LMD-940W - Manuals

Precaution 5 Precaution On Safety • Operate the unit only with a power source as specified in the “Specifications” section. • A nameplate indicating operating voltage, etc., is located on the bottom. • Should any solid object or liquid fall into the cabinet, unplug the unit and have it checked by qu...

Features 6 On Repacking Do not throw away the carton and packing materials. They make an ideal container which to transport the unit. On Mounting on a Rack Leave 1U space empty above and below the monitor to ensure adequate air circulation or install a fan to maintain the monitor’s performance. If y...

Features 7 Protection plate You can attach and detach the LCD screen’s protection plate easily with the four screws. Strong, slim and lightweight The strong, slim, and lightweight design of the aluminum die-cast chassis makes the monitor suitable for use with rack mounts or as a portable monitor. Th...

Location and Function of Parts and Controls 8 Location and Function of Parts and Controls Front Panel a Tally lamp You can check the status of the monitor by the color of the tally lamp.The tally lamp lights in red, green or amber according to the setting of PARALLEL REMOTE in the REMOTE menu. b Pro...

Location and Function of Parts and Controls 9 For details of the function assigned to the function button, see page 22. h Menu operation buttons Displays or sets the on-screen menu. MENU SEL (menu selection) control When the menu is displayed, turn the control to select a menu item or setting value,...

Location and Function of Parts and Controls 10 Input Signals and Adjustable/Setting Items a : Adjustable/can be set × : Not adjustable/cannot be set *1 Adjustment of SUB CONTROL is the same.*2 Only the interlace signal is input.*3 The audio levels of WFM or ALM are displayed when SDI signal is input...

Location and Function of Parts and Controls 11 Rear/Bottom Panel a SDI (3G/HD/SD) input and output connectors (BNC) IN connector Input connector for serial digital component signals. OUT connector Output connector for serial digital component signals. Note The signal from the OUT connector does not ...

Installing to the Rack (Using MB-531) 12 CAUTION • For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to this port. Follow the instructions for this port. • When an optional LAN cable is connected, use a shield type cable to prevent miss-operation...

Power Supply 13 Power Supply Attaching the AC Adaptor Attaching Removing Notes • The AC adaptor is for LMD-940W only. It cannot be used with other products. • To remove the AC adaptor, first unplug the AC power cord and then remove the AC adaptor. Connecting the AC Power Cord Attach the AC adaptor t...

Selecting the Default Settings 14 Selecting the Default Settings When you turn on the unit for the first time after purchasing it, select the area where you intend to use this unit from among the options. The default setting values for each area 1 Press the 1 (standby) switch. The unit is turned on ...

Selecting the Menu Language 15 2 If LATIN AMERICA is selected: 4 If ASIA EXCEPT JAPAN is selected: Customers who will use this unit in the shaded areas shown in the map below should select NTSC AREA.Other customers should select PAL AREA. 3 Press the MENU SEL control or the ENTER button. The SELECT ...

Using the Menu 16 The setting items (icons) in the selected menu are displayed in yellow. 4 Turn the MENU SEL control to select “LANGUAGE”, then press the MENU SEL control or the ENTER button. The selected item is displayed in yellow. 5 Turn the MENU SEL control to select a language, then press the ...

Using the Menu 17 The menu icon presently selected is shown in yellow and setting items are displayed. 3 Select an item. Turn the MENU SEL control to select the item, then press the MENU SEL control or the ENTER button.The item to be changed is displayed in yellow.If the menu consists of multiple pa...

Adjustment Using the Menus 18 Adjustment Using the Menus Items The screen menu of this monitor consists of the following items. STATUS (the items indicate the current settings.) FORMATCOLOR TEMPHDMI FORMATNTSC SETUPSCAN MODEPOWER SAVINGI/P MODEModel name and serial number COLOR TEMP/SPACE COLOR TEMP...

Adjustment Using the Menus 19 You need to use the measurement instrument to adjust the white balance.Recommended: Konica Minolta color analyzer CA-210 USER CONTROL menu The USER CONTROL menu is used for adjusting the picture.Items that cannot be adjusted depending on the input signal are displayed i...

Adjustment Using the Menus 20 USER CONFIG menu The USER CONFIG menu is used for setting the system, marker, WFM/ALM display, function button, and audio. SYSTEM SETTING AUTO CHROMA/PHASE Adjusts color intensity (CHROMA) and tones (PHASE). • AUTO ADJ VALUE : Selects ON or OFF of the auto adjustment. W...

Adjustment Using the Menus 21 MARKER SETTING WFM/ALM (waveform monitor and audio level meter) DISPLAY SETTING I/P MODE (picture delay minimum) Selects to set the delay by the picture processing to the minimum level when the interlace signal is input.• INTER-FIELD : Mode for giving precedence to the ...

Adjustment Using the Menus 22 FUNCTION BUTTON SETTING About the function assigned to the function button SCAN Press the button to change the scan size of the picture. With every press of the button for the 4:3 display, the picture switches in the sequence NORMAL scan t OVER scan t NATIVE. With every...

Adjustment Using the Menus 23 ASPECT Press the button to set the aspect ratio of the picture, 4:3 or 16:9. Note The panel of the monitor is 15:9.When the 16:9 signal is displayed, black bars appear in the upper and lower positions of the display. This is not a malfunction (see “Scan mode image” on p...

Adjustment Using the Menus 24 AUDIO SETTING REMOTE menu 768 × 480 (575i, 576P) – The image is scaled horizontally to display in an aspect ratio of 4:3. Submenu Setting SDI AUDIO SETTING Sets the audio channel when SDI signal is input.• 3G/HD/SD : Selects from among channels CH1 to CH16, odd channel ...

Adjustment Using the Menus 25 KEY INHIBIT menu You can lock the setting so that they cannot be changed by an unauthorized user.Select OFF or ON.If you set to ON, all items are displayed in black, indicating the items are locked. SERIAL REMOTE MONITOR CONTROLLER CONNECTION Selects the mode to be used...

Troubleshooting / Specifications 26 Troubleshooting This section may help you isolate the cause of a problem and as a result, eliminate the need to contact technical support.• The unit cannot be operated t The key protection function works. Set the KEY INHIBIT setting to OFF in the KEY INHIBIT menu....

Specifications 27 General Power AC 100 to 240 V, 50/60 Hz, 0.5 A to 0.3 A DC 12 V, 1.9 A Power consumption Maximum: approx. 27 W Peak inrush current (1) Power ON, current probe method: 30 A (100 V), 60 A (240 V) (2) Hot switching inrush current, measured in accordance with European standard EN55103-...

Specifications 28 Pin assignment PARALLEL REMOTE connector Modular connector(8-pin) You can allocate functions using the REMOTE menu (see page 24). Wiring required to use the Remote Control Connect the function you want to use with a Remote Control to the Ground (Pin 5). Available signal formats The...

Dimensions 29 Dimensions Front Side Bottom (Without the stand) Top Side (When the stand is moved) 222.4 ( 8 7 / 8 ) 183.5 ( 7 1 / 4 ) 166 ( 6 5 / 8 ) 17.5 ( 23 / 32 ) 148.8 ( 5 7 / 8 ) 161.8 ( 6 3 / 8 ) 13 ( 1 7 / 3 2 ) 161.5 ( 6 3 / 8 ) 130 ( 5 1 / 8 ) 149.6 ( 6 ) 5.6 ( 1 / 4 ) 70 ( 2 7 / 8 ) 60 ( ...