Sony HDC-930 - Manuals

3 (E) HDC-900/950 IMM Manual Structure Purpose of this manual This manual is the installation and maintenance manual of HD Color Camera HDC-900/910/950/930 and HD CCD Block Adaptor HKC-T950 for HDC-950/930. This manual is intended for use by trained system and service engineers, and isprovided infor...

4 (E) HDC-900/950 IMM ..... “Semiconductor Pin Assignments” CD-ROM (Available on request) This “Semiconductor Pin Assignments” CD-ROM allows you to search for semiconductors used in B&P Company equipment.Semiconductors that cannot be searched for on this CD-ROM are listed in the maintenance manu...

1-1 (E) HDC-900/950 IMM Section 1 Installation Overview 1-1. Checking before Installation 1-1-1. Checking the ROM and Software Version When connecting the peripheral equipment in the list below to HDC-900/910/950/930, be sure to check that the ROM and software version on each peripheral device is co...

1-3 (E) HDC-900/950 IMM !. !; 8 !, 2 4 !/ !- !] 5 36 !\ 9 7 1 !' ![ * @[ @- @= @/!\ @\ @- @[ @= @] HDC-950/930 Connector Layout * : Use 4 connector by selecting PROMPTER OUT, GENLOCK IN and RET IN signals with the switch. PROMPTER OUT signal become effective when the camera is connected to CCU.GENLO...

1-4 (E) HDC-900/950 IMM 1 2 3 4 7 7 7 7 7 RET CONTROL (6P FEMALE) (External view) No. Signal I/O Specifications 1 INCOM 1 IN Zi > 10 k Z MIC ON/OFF ON : GNDOFF : OPEN 2 INCOM 2 IN Zi > 10 k Z MIC ON/OFF ON : GNDOFF : OPEN 3 GND —— 4 NC No connection 5 RET 1 ON/OFF IN Zi > 10 k Z ON : GNDOFF...

1-9 (E) HDC-900/950 IMM 1 5 10 11 16 17181920 234 !; !; !; !; !; VF (20P FEMALE) (HDC-950/930) (External view) No. Signal I/O Specifications 1 S-DA TA IN/OUT TTL level 2 NC No connection 3 NC No connection 4 SCK OUT TTL level 5 NC No connection 6 NC No connection 7 NC No connection 8 G TALLY OUT ON ...

1-13 (E) HDC-900/950 IMM Yellow Black White Red Red White Blue Red White Orange White Red Yellow White Black Blue Red Brown Gray Red 1-2-2. Wiring Diagrams for Cables CCA-5 Cable HDCZ Cable 1-2. Connectors and Cables

1-19 (E) HDC-900/950 IMM S104 S103 S1 S101 AU-271 board (A side) S102 S201 S2 S202 S301 S304 S203 S204 S303 B C D E F G A 5 4 3 2 1 AU CM DYNINCOM 1 INCOM 1 switch INCOM 1 MIC GAIN switch MIC GAIN DYNINCOM 2 MIC GAIN MICMONITOR ON + 0 _ + 0 _ OFF INCOM 2 switch INCOM 2 MIC GAIN switch MIC MONITOR sw...

1-21 (E) HDC-900/950 IMM 1-5. Switch Setting on the Boards * 1: The Tracker connector communicates to INCOM1 at the standard setting, yet it is communicable to INCOM2 by setting S1-1, S301-1 and S301-4to ON. * 2: When setting S2-1 or S2-2 to ON, set bit1 and bit2 of S101, S102, S201 and S202 as show...

1-25 (E) HDC-900/950 IMM Screw (B4 x 20) Screws (B3 x 6) Screws (B3 x 8) Pad spacer Shoulder pat assembly 1-7. Adjusting the Position of the Shoulder Pad (HDC-950/930) The shoulder pad is factory-configured to the more for- ward position considering the mass of the camera, yet it isadjustable accord...

1-27 (E) HDC-900/950 IMM 1-10. Disconnecting/Reconnecting Flexible Card Wire m. Be sure to turn off the power when disconnecting and connecting the flexible card wire. To power off, be sure to disconnect the cable connected to the DC IN connector or the battery, in addition to turningoff the power s...

1-28 (E) HDC-900/950 IMM AU-271 board suffix -13 and higher (B side) R271 1 A B C D E F G 2 3 4 5 1-11. Notes on Use of the RTS Kit 1-11. Notes on Use of the RTS Kit Connecting the RTS Intercom System Kit BKP-7913(option) to the INTERCOM 2 connector of HDC-900/910/ 950/930 allows the INTERCOM 2 conn...

2-1 (E) HDC-900/950 IMM Optical contacts (white) Insert the shorter nose end Shock absorber portion Handle 2-1. Cleaning of Connector/Cable It is recommendable to clean the optical contact portionsmentioned below before connecting this unit to the camera control unit. . CCU connector of this unit . ...

2-2 (E) HDC-900/950 IMM Optical contacts (white) Alignment sleeve 2. When the turn stops, pull out the remover in thestraight line forcedly. n The alignment sleeve can be removed/reinstalled with the sleeve itself attached to the tip of the remover.Great care should be taken so as not to lose or dam...

2-3 (E) HDC-900/950 IMM PrecisionP2.6 x 5 PrecisionP2.6 x 5 PrecisionP2.6 x 5 Top chassis cover assembly Fan grill holder Fan grill PrecisionP2.6 x 5 2-2. Cleaning the Vent Portion of the Fan (HDC-950/930 only) A part for preventing from dust is attached in the vent portion of the fan. Clean this co...

2-4 (E) HDC-900/950 IMM 2-3. Replacing the Fuse w The fuse is critical for safely operating. Do exchange with the fuses authorized by the manufacturer, otherwise a fireand electric shock may occur. 2-3-1. HDC-900/910 In the power supply portion of the HDC-900/910, fuses for protecting from the overc...

3-1 (E) HDC-900/950 IMM 3-1. Setup Menu The setup menu is used for selecting various setting values, items displayed on the viewfinder screen, the method of displaying, and adjustments. The menu is displayed on the viewfinder screen. The menu canalso be displayed by connecting an external monitor to...

3-3 (E) HDC-900/950 IMM 3-1. Setup Menu DISPLAY switch MENU switch Rotary Encoder Switches (HDC-950/930) DISPLAY switch ON : Displays characters and messages indicating the settings and operating status of the unit on theviewfinder screen. OFF : Turns off all the displays on the viewfinder screen. M...

3-4 (E) HDC-900/950 IMM 3-2. TOP Menu 3-2. TOP Menu The TOP menu is provided for indicating the whole configuration of the menu items. Displaying the TOP menu HDC-900/910 : Set the DISPLAY switch from “OFF” to “MENU” while pressing the MENU SELECT switch toward the “ENTER” side. HDC-950/930 : Set th...

3-7 (E) HDC-900/950 IMM 3-4. PAINT Menu The PAINT menu contains overall general paint adjustment items, such as white adjustment.For details, refer to the operation manual supplied with this unit. SW STATUS page Item Setting Description FLARE ON, OFF Sets the flare correction circuit to ON or OFF. G...

3-8 (E) HDC-900/950 IMM VIDEO LEVEL page Item Setting Description WHITE _ 99 to 99 Adjusts the white level of R, G, B. BLACK _ 99 to 99 Adjusts the black level of R, G, B and master. FLARE _ 99 to 99 Adjusts the flare level of R, G, B and master. GAMMA _ 99 to 99 Adjusts the gamma correction curve o...

3-9 (E) HDC-900/950 IMM GAMMA page Item Setting Description LEVEL _ 99 to 99 Adjusts the gamma correction curve of the R, G, B and master. COARSE 0.35 to 0.90 Sets the correction curve of the master gamma in 0.05 steps. TABLE STANDARD, Selects the gamma table. USER * STANDARD : Select the standard g...

3-10 (E) HDC-900/950 IMM BLK GAMMA page Item Setting Description RGB LEVEL _ 99 to 99 Adjusts the black gamma of the R, G, B and master. RGB RANGE 1, 2, 3, 4 Sets the upper limit of the video level which the RGB black gammaaffects. ON, OFF Sets the RGB black gamma correction function to ON or OFF. Y...

3-12 (E) HDC-900/950 IMM (Display is initial values.) < K N E E > [ R ] [ G ] [ B ] [ M ]P O I N T : 0 0 0 0S L O P E : 0 0 0 0W H T C L P : 0 0 0 0K N E E S A T L E V E L 0 K N E E : O NK N E E S A T : O F FW H T C L I P : O NT E S T : O F F < K N E E > [ R ] [ G ] [ B ] [ M ]P O I N T ...

3-14 (E) HDC-900/950 IMM SKIN DETAIL page Item Setting Description SKIN DTL ON, OFF When this setting is ON, the setting [1] of the channel 1 is always setON. Sets the skin detail function to ON or OFF. SKIN GATE b) ON, OFF Sets the zebra indication of the skin tone detail portion to ON or OFF. CH S...

3-15 (E) HDC-900/950 IMM USER MATRIX page Item Setting Description R-G, R-B, _ 99 to 99 Sets the linear matrix coefficient for each R-G, R-B, G-R, G-B, B-R, G-R, G-B, _ 99 to 99 and B-G. B-R, B-G, _ 99 to 99 MATRIX a) ON, OFF Sets the linear matrix correction function to ON or OFF. PRESET a) ON, OFF...

3-16 (E) HDC-900/950 IMM MULTI MATRIX page Item Setting Description PHASE 0, 23, 45, 68, 90, Sets the angle that varies the multi matrix correction function. 113, 135, 158, 180, (sixteen-axis mode) 203, 225, 248, 270,293, 315, 338 HUE _ 99 to 99 Adjusts the color phase the multi matrix correction fu...

3-17 (E) HDC-900/950 IMM SHUTTER page Item Setting Description SHUTTER ON, OFF Sets the shutter/ECS mode to ON or OFF. Table below a) Sets the shutter speed.(The selectable shutter speed varies with each format.) ECS FREQ Table below b) Sets the ECS frequency.(The selectable ECS frequency variable r...

3-18 (E) HDC-900/950 IMM SCENE FILE page Item Setting Description 1, 2, 3, 4, 5 Saves and calls the scene file (the data painted in accordance with theshooting scene.) (Same as the SCENE FILE page in the FILE menu.) STORE STANDARD Returns the current paint adjustment amount and switch settings to th...

3-21 (E) HDC-900/950 IMM AUTO IRIS page Item Setting Description AUTO IRIS b) ON, OFF Sets the auto iris function to ON to OFF. WINDOW 1, 2, 3, 4, 5, 6 Selects the auto iris window. a) OVERRIDE _ 99 to 99 Sets the reference value of the auto iris level by ± 2 focus. _ 99 (2 iris nearly closed) ↔ 99 ...

3-22 (E) HDC-900/950 IMM < S D I > P R O M P T E R : O F FB N C S D I O U T : O F F < O U T P U T > P R O M P T E R : O F FB N C S D I O U T : O F F L I N E R E X P : O F F (Display is initial values.) ROM Version lower than 1.30 ROM Version 1.30 or higher MULTI FORMAT page Item Setting ...

3-24 (E) HDC-900/950 IMM OTHERS1 page Item Setting Description FAN MODE AUTO1, Sets the fan mode. AUTO2, AUTO1 : normal mode MIN, MAX AUTO2 : silent modeMIN : minimum rotation mode MAX : maximum rotation mode H PHASE _ 3072 to 1023 Adjusts the H phase. CHU BARS ON, OFF Sets the CHU BARS to ON or OFF...

3-25 (E) HDC-900/950 IMM 3-5. MAINTENANCE Menu OTHERS2 page Item Setting Description MENU RESUME OPE MENU, Sets the menu screen displayed when starting the menu. OFF, ALL OPE MENU : Starts to display from the page in the operation menu, which was displayed at powering off of the previous time. OFF :...

3-27 (E) HDC-900/950 IMM < O P E R A T O R F I L E > R E A D ( M S C A M ) W R I T E ( C A M M S ) P R E S E TS T O R E P R E S E T F I L E F I L E I D :C A M C O D ED A T E 3-6. FILE Menu File menu is used to operate the file such as saving the reference file. OPERATOR FILE page Item Setting ...

3-29 (E) HDC-900/950 IMM REFERENCE page Item Setting Description STORE FILE * 1 Registers the adjustment values of each item as the reference file. STANDARD * 1 Returns the data registered in the reference file to the reference value. READ (MS → CAM) Reads out reference file from the memory stick to...

3-31 (E) HDC-900/950 IMM 3-6. FILE Menu FILE CLEAR page Item Setting Description PRESET * 1 Returns the preset value of the operator file set by the user to the OPERATOR original value at factory setting. REFERENCE (ALL) * 1 Returns each adjustment value registered in the reference file to theorigin...

3-32 (E) HDC-900/950 IMM 3-7. DIAGNOSIS Menu 3-7. DIAGNOSIS Menu The DIAGNOSIS menu displays the self-diagnosis of every plug-in board and photo-receptive conditionof the optical connector, etc. SDI page Item Setting Description OPTICAL LEVEL GREEN, Displays a photo-receptive condition of the optica...

3-33 (E) HDC-900/950 IMM < B O A R D S T A T U S > R O M : V 1 . 0 0 O H B : O K S G : O KV A : O K A T : O KD P R : O K A U : O KV D A : O K R E : O KD A D : O K P S : O KS D I : O KD A P : O K BOARD STATUS page Item Setting Description ROM Indicates the ROM version for IC1/AT-130 board OHB O...

HDC-900/950 IMM 4-1 (E) Section 4 File System The HDC-900/910/950/930 are equipped with various file systems for managing data. 4-1. File Structure The following six types of files are available. 1. Operator File Stores the items displayed on the viewfinder and switch settings for camera operator. T...

HDC-900/950 IMM 4-5 (E) 4-4. Registering the Scene File Storing the Scene File to the Memory Stick (Refer to step 1 of Fig. 4-3.) The scene file stored in the camera unit is stored to the memory stick.Set the setup menu as follows. Reading the Scene File from the Memory Stick (Refer to step 3 of Fig...

4-10 (E) HDC-900/950 IMM 4-7. Registering the OHB File 4-7. Registering the OHB File The OHB file is used for storing the maintenance adjustment values of the CCD block and the data willbe stored in the camera. The data can be stored using the setup menu or the MSU (master setup unit). The items to ...

HDC-900/950 IMM 4-11 (E) 4-7. Registering the OHB File 4-7-2. Adjusting the ND Offset The white balance may be slightly deviated in the ND filters. In such cases, adjust the offset. Taking theND filter 1 white balance as the reference, the ND offset stores the deviation of the white balance of ND fi...

4-14 (E) HDC-900/950 IMM 4-8. File items page item OPERATOR REFERENCE SCENE OHB LENS STANDARD ( * 9) Power is Factory turned ON set 10 PRESET MATRIX SW _ _ _ REF _ OFF MATRIX SW _ _ _ REF _ OFF 11 MULTI MATRIX PHASE _ _ _ _ _ _ _ 0 MULTI MATRIX HUE _ _ _ REF _ 0 MULTI MATRIX SAT _ _ _ REF _ 0 MULTI ...

4-16 (E) HDC-900/950 IMM 4-8. File items MSU connected only item OPERATOR REFERENCE SCENE OHB LENS STANDARD ( * 9) Power is Factory turned ON set V DTL CREATION MODE _ _ _ REF _ Y V DTL CONTROL MODE _ _ _ _ REF _ H/V KNEE MAX _ OFF _ _ OFF OFF OFF AUTO KNEE POINT _ _ _ _ REF _ 0 WHITE SETUP MODE _ _...

Printed in Japan Sony Corporation 2003. 10 08 B&P Company ©2000 H K C - T 9 5 0 ( S Y ) H D C - 9 0 0 ( S Y ) H D C - 9 0 0 / L ( J ) H D C - 9 1 0 ( U C J, C E ) H D C - 9 1 0 / L ( J ) H D C - 9 3 0 ( S Y ) H D C - 9 5 0 ( J N , S Y ) J, E 3 - 2 0 4 - 3 3 8 - 0 8