Sony CPD-E400E - Manuals - manualsarea.com

Page 2 - LEAKAGE TEST; COMPONENTS IDENTIFIED BY SHADING AND MARK; Earth Ground

CPD-E400/E400E – 2 – LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part hav- ing a return to chassis, must not exceed 0.5 mA (500 microam- peres). Leakage current can be measured by any one of three methods. 1. A commerc...

Page 3 - ** When your computer is in a power saving mode, MONITOR IS IN; If the

CPD-E400/E400E – 3 – POWER SAVING FUNCTION DIAGNOSIS This monitor meets the power-saving guidelines set by VESA, E NERGY S TAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically red...

Page 4 - TIMING SPECIFICATION

CPD-E400/E400E – 4 – TIMING SPECIFICATION MODE AT PRODUCTION MODE 1 MODE 2 RESOLUTION 738 X 414 1600 X 1200 CLOCK 28.322 MHz 202.500 MHz HORIZONTAL H-FREQ 31.469 kHz 93.750 kHz usec usec H. TOTAL 31.777 10.667 H. BLK 5.720 2.765 H. FP 0.318 0.316 H. SYNC 3.813 0.948 H. BP 1.589 1.501 H. ACTIV 26.057...

Page 5 - TABLE OF CONTENTS; Section; SAFETY RELATED ADJUSTMENT; Schematic Diagrams and Printed Wiring; ELECTRICAL PARTS LIST

CPD-E400/E400E – 5 – TABLE OF CONTENTS Section Title Page 1. GENERAL ................................................................. 1-1 2. DISASSEMBLY 2-1. Cabinet Removal ................................................ 2-1 2-2. Shield (EMI, Video), Side Cover (L and R) Removal ....................

Page 6 - Precautions; US; Identifying parts and controls

SECTION 1 GENERAL The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual. 1-1 4 Precautions Warning on power connections • Use the supplied power cord. If you use a different ...

Page 7 - Setup; Step 1: Connect your monitor to; Step 2: Connect the power cord

1-2 6 Setup Before using your monitor, check that the following accessories are included in your carton:• Power cord• Current G3 adapter (for beige system) (1)• Setup Disk (1)• Warranty card• Notes on cleaning the screen’s surface• This instruction manual Step 1: Connect your monitor to your compute...

Page 8 - Customizing Your Monitor; Navigating the menu

1-3 8 Selecting the on-screen menu language (LANG) English, French, German, Spanish, Italian, Dutch, Swedish, Russian and Japanese versions of the on-screen menus are available. The default setting is English. 1 Press the center of the control button. See page 9 for more information on using the con...

Page 11 - Resetting the adjustments; Technical Features; Preset and user modes; Power saving function; Troubleshooting

1-6 14 THIN HORIZONTAL LINE The lines that appear on your screen are damper wires. See page 15 for more information about the damper wires. DISTORTED SHAPE If the shape of the picture on the screen seems distorted, try adjusting the picture’s geometry. Move the control button , to jump directly to t...

Page 12 - Trouble symptoms and remedies

1-7 16 Trouble symptoms and remedies If the problem is caused by the connected computer or other equipment, please refer to the connected equipment’s instruction manual.Use the self-diagnosis function (page 18) if the following recommendations do not resolve the problem. Symptom Check these items No...

Page 13 - Self-diagnosis function; Specifications

1-8 18 Self-diagnosis function This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer, the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is i...

Page 14 - Cabinet; Video shield

CPD-E400/E400E 2-1. CABINET REMOVAL SECTION 2 DISASSEMBLY 2-2. SHIELD (EMI, VIDEO), SIDE COVER (L and R) REMOVAL 2-1 Bezel assembly 1 3 Cabinet Push in the tip of a screwdriver about 5mm to unlock the two claws. 1 Two claws Two claws 2 Two screws(+BVTP 4 x 16) Bezel assembly Cabinet Cabinet 5 Four s...

Page 15 - D BOARD REMOVAL; A board

CPD-E400/E400E 2-3. A BOARD REMOVAL 2-4. REAR SHIELD COMPLETE ASSY, D BOARD REMOVAL 2-2 3 Three screws(+BVTT 3 x 8) 4 A board CN306 CN311 CN303 CN309 CN305 1 Screw(+BVTT 4 x 8) 2 Cable stopper 5 Three screws(+BVTT 3 x 8) CN601 CN600 CN303 8 D board N board 6 Screw(+P 3.5 x 20) 7 Two screws(+BVTP 3 x...

Page 17 - Anode Button

CPD-E400/E400E 2-7. PICTURE TUBE REMOVAL 2-4 CN11 CN801 CN1 2pin 4 Four screws(Tapping screw (5)) 3 Three connectors 7 Neck assembly 1 Anode cap 2 A board 8 Deflection yoke 6 Picture tube 5 Bezel assembly 3 When one side of the rubber cap isseparated from the anode button, theanode-cap can be remove...

Page 19 - SECTION 3; a) High Voltage Adjustment; Note:Perform high voltage adjustment after the rough adjust-

CPD-E400/E400E Part Replaced ( ] ) D Board T901(FBT), IC901, R924, R925, RV901 • Mounted D board D Board T901(FBT), R917, R918, R923, R920,R919, R1004, C920,D911, R912, • Mounted D board D Board R933, R932, R921, R1006, D915, D917,IC901, T901(FBT) • Mounted D board b) High Voltage Hold-Down Function...

Page 20 - Landing Rough Adjustment

CPD-E400/E400E SECTION 4 ADJUSTMENTS 4-1 • Landing Rough Adjustment 1. Enter the full white signal. (or the full black dots signal).2. Adjust the contrast to the maximum.3. Make the screen monogreen.Note: Off the outputs from R ch and B ch of SG.4. Reverse the DY, and adjust coarsely the purity magn...

Page 21 - Convergence Rough Adjustment; Adjust the focus volume 1 and 2 for the optimum focus.; Convergence Specification; b) Flush the shaded portions of TLH plate with the DY rear; All mode; MODE

CPD-E400/E400E Connect the communication cable of the computer to the connector located on the D board on the monitor. Run the service softwareand then follow the instruction. IBM AT Computer as a Jig 1-690-391-21 1 A-1500-819-AInterface Unit 2 *The parts above ( ) are necessary for DAS adjustment. ...

Page 24 - RGB OUT

5-5 5-6 5-2. FRAME SCHEMATIC DIAGRAM 5-3. CIRCUIT BOARDS LOCATION D A H N H KB KG KR G1 G2 GM G4 RCV HV 1 2 3 4 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 1 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 1 2 3 4 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6...

Page 25 - μμ; WIRING BOARDS; Terminal name of semiconductors in silk screen; — A BOARD —; : Refer to Terminal name of semiconductors; • A BOARD SEMICONDUCTOR LOCATION; IC

Note: • All capacitors are in µ F unless otherwise noted. (pF: µµ F) Capacitors without voltage indication are all 50 V. • Indication of resistance, which does not have one for rating electrical power, is as follows. Pitch: 5 mm Rating electrical power 1/4 W (CHIP : 1/10 W) • All resistors are in oh...

Page 26 - • A BOARD WAVEFORMS; C BLOCK; PICTURE

5-9 5-10 (1) Schematic Diagram of A Board 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A B C D E F G H I 4.16 Vp-p (H) 4.16 Vp-p (H) 4.08 Vp-p (H) 49.8 Vp-p (H) 49.8 Vp-p (H) 48.8 Vp-p (H) 49.8 Vp-p (H) 49.8 Vp-p (H) 48.8 Vp-p (H) 1.78 Vp-p (8 MHz) 1 2 3 4 5 6 7 8 9 0 • A BOARD WAVEFORMS 4.7 0.4 3.8 4.9 4 0 4.1...

Page 27 - BOARD WAVEFORM

5-11 5-12 (2) Schematic Diagrams of D ( a , b , c ) Board 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 A B C D E F G H I Schematic diagram Ò A A A A A board Schematic diagram D D D D D - a board l • Divided circuit diagram One sheet of D board circuit diagram is divided into three sheets, each having the code...

Page 28 - BOARD WAVEFORMS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 A B C D E F G H I 5-14 5-13 • Divided circuit diagram One sheet of D board circuit diagram is divided into three sheets, each having the code D- a to D- c . For example, the destination ab1 on the code D- a sheet is connected to ab1 on the D- b sheet. a b 1 Ref. No. ...

Page 29 - BOARD; : Refer to Terminal name of semiconductors in silk screen; • D BOARD SEMICONDUCTOR LOCATION

5-15 5-16 1 2 3 4 5 6 7 8 9 10 A B C D E F G H I Schematic diagram D D D D D - c board l Schematic diagram Ò D D D D D - b board • Divided circuit diagram One sheet of D board circuit diagram is divided into three sheets, each having the code D- a to D- c . For example, the destination ab1 on the co...

Page 30 - — D BOARD —

5-17 5-18 — D BOARD — D µ -COM, CY, DEFLECTION, POWER, H DEF, HV 1 2 3 4 5 6 7 A B C D E NOTE:The circuit indicated as left contains high voltage of over600 Vp-p. Care must be paid to prevent an electric shock ininspection or repairing.

Page 31 - DSP; — H BOARD —

1 2 3 4 5 6 7 8 9 10 11 12 13 14 A B C D E F G H I 5-20 5-19 Schematic diagrams N N N N N , H H H H H boards l N DSP H USER CONTROL (3) Schematic Diagrams of N, H Boards — N BOARD (Conductor Side) — — N BOARD (Component Side) — — H BOARD — 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 ...

Page 34 - DESCRIPTION; SECTION 6; The components identified

CPD-E400/E400E • Items marked " * " are not stocked since t h e y a r e s e l d o m r e q u i r e d f o r r o u t i n eservice. Some delay should be anticipatedwhen ordering these items. • I t e m s w i t h n o p a r t n u m b e r a n d n o description are not stocked because theyare seldom ...

Page 37 - Les composants identifiés par la marque; SECTION 7; The components identified by

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified ¡ marked are critical for safety.Replace only with the part number specified. Les composants identifiés par la marque ¡ sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numér...

Page 40 - AD

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified ¡ marked are critical for safety.Replace only with the part number specified. Les composants identifiés par la marque ¡ sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numér...

Page 47 - DHN

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified ¡ marked are critical for safety.Replace only with the part number specified. Les composants identifiés par la marque ¡ sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numér...

Page 48 - Sony Corporation; Computer Display Company; English; Printed in Japan

REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK The components identified ¡ marked are critical for safety.Replace only with the part number specified. Les composants identifiés par la marque ¡ sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numér...