Sony CDP-CE275 - Manuals - manualsarea.com

Page 2 - ADJ MODE; ADJ Mode Special Function Table; Button

10 CDP-CE275/CE375 SECTION 4 TEST MODE ADJ MODE NOTE: This mode cannot be performed without a general remote com-mander. 1. Chuck the CD first, and then turn OFF the power.2. Short-circuit the test point TP1 (ADJ) of the MAIN board and ground with a lead wire. 3. Press the [POWER] button to turn ON ...

Page 3 - Buttons and Corresponding Button Numbers; All lit; Partial lighting 2

11 CDP-CE275/CE375 Buttons and Corresponding Button Numbers Button Button Number or Display DISC1 12 DISC2 11 DISC3 10 DISC4 9 DISC5 8 PLAY MODE 20 PEAK SEARCH 19 FADER 18 REPEAT 17 TIME 16 H (PLAY) Partial lighting 1 X (PAUSE) Partial lighting 2 x (STOP) All lit EX-CHANGE 35 DISC SKIP 36 m 24 M 25 ...

Page 4 - Display contents

12 CDP-CE275/CE375 AGING MODE For the aging mode, three modes of all mode, disc table mode, and loading mode are available. This set has the Aging mode for operation check of the mechanism deck.• If a failure occurred The aging operation stops and a faulty status is displayed on the fluorescent indi...

Page 5 - S Curve Check; • Try to measure several times to make sure than the ratio of A : B; Checking Location: BD board; SECTION 5

13 CDP-CE275/CE375 Ver 1.1 2001.07 Note: 1. CD Block is basically designed to operate without adjustment. There- fore, check each item in order given. 2. Use PATD-012 disc (4-225-203-01) unless otherwise indicated.3. Use an oscilloscope with more than 10M Ω impedance. 4. Clean the object lens by an ...

Page 6 - BD board

14 CDP-CE275/CE375 Ver 1.1 2001.07 E-F Balance Check Connection: Procedure:1. Set the test disc (PATD-012). Disc chucking operation iscomplete, then press the [POWER] button to turn the power off. 2. Connect an oscilloscpe to test point TP (TE1) and TP (VC) onthe BD board. 3. Connect between test po...

Page 7 - NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS; • Voltages and waveforms are dc with respect to ground; • Circuit Boards Location

15 15 CDP-CE275/CE375 SECTION 6 DIAGRAMS 6-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Schematic Diagram:• All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolyticsand tantalums. • All resistors are in Ω and 1 / 4 W or less...

Page 8 - SCHEMATIC DIAGRAM – BD Board –; See page 24 for Waveforms.; IC BD

17 17 CDP-CE275/CE375 6-3. SCHEMATIC DIAGRAM – BD Board – • See page 24 for Waveforms. • See page 24 for IC Block Diagrams. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont...

Page 9 - SCHEMATIC DIAGRAM – JUNCTION/SENSOR/LOADING MOTOR Boards –; See page 25 for IC Block Diagram.; TO MAIN BOARD

19 19 CDP-CE275/CE375 6-5. SCHEMATIC DIAGRAM – JUNCTION/SENSOR/LOADING MOTOR Boards – • See page 25 for IC Block Diagram. TO MAIN BOARD (Page 21) IC BD

Page 10 - SCHEMATIC DIAGRAM – MAIN Board –; See page 24 for Waveform.

21 21 CDP-CE275/CE375 6-7. SCHEMATIC DIAGRAM – MAIN Board – • See page 24 for Waveform. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les ...

Page 11 - SCHEMATIC DIAGRAM – PANEL Section –

23 23 CDP-CE275/CE375 6-9. SCHEMATIC DIAGRAM – PANEL Section – The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piè...